Study guide
8.1 Division of the State Architect (DSA): Field Act & Public K-12/Community College Oversight
California Supplemental Examination CSE
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: California Architects Practice Act & Professional Practice
1.1 Licensing, Board Authority, and Unlicensed Practice Exceptions 1.2 Mandatory Written Contracts & Required Provisions 1.3 Architect's Stamp, Signature, and Professional Liability
2 Chapter 2: Professional Conduct, Ethics & Business Entities
2.1 Rules of Professional Conduct & Disciplinary Grounds 2.2 Permissible Business Entities, Firm Names, and Filing Requirements 2.3 Copyright, Instruments of Service & Ownership of Architectural Documents
3 Chapter 3: Contractual Roles, Scope & Consultant Agreements
3.1 Standard Owner-Architect Agreements (AIA B101 / B102) & California Practice Realities 3.2 Consultant Selection, Prime-Consultant Agreements & Liability Flow-Down (AIA C401) 3.3 Project Delivery Methods & Impact of Project Funding Sources
4 Chapter 4: Risk Management, Dispute Resolution & Project Planning
4.1 Professional Standard of Care & Managing Contractual Risk and Liability 4.2 Dispute Resolution in California Practice: Mediation, Arbitration, and Litigation 4.3 Project Scheduling, Budgeting Assumptions, and Milestone Approvals
5 Chapter 5: Site Feasibility, Schematic Design & Discretionary Approvals
5.1 Site Feasibility Studies, Existing-Conditions Due Diligence & Project Impacts 5.2 Programming, Schematic Design Development & Stakeholder Engagement 5.3 Local Land-Use Control: General Plans, Zoning, Specific Plans & Local Ordinances 5.4 The Discretionary Approval Process: Use Permits, Variances, Design Review & Hearings 5.5 Entitlement Exhibits, Conditions of Approval & Leading the Approval Team
6 Chapter 6: Environmental Review & CEQA Compliance
6.1 CEQA Regulatory Framework: Lead, Responsible, and Trustee Agencies 6.2 CEQA Process: Statutory & Categorical Exemptions, Initial Studies, and (Mitigated) Negative Declarations 6.3 Environmental Impact Reports (EIR) & Official Filings (NOP, NOC, NOD, NOE)
7 Chapter 7: California Coastal Act & Specialized Regional Regulations
7.1 California Coastal Commission & Coastal Development Permits (CDP) 7.2 Local Coastal Programs (LCP), Coastal Zone Boundaries, and Appeals 7.3 Clean Air Act (CARB/AQMDs) & Clean Water Regulations (Porter-Cologne, RWQCB & SWPPP)
8 Chapter 8: State Agency Jurisdictions: DSA, HCAI & Essential Services
8.1 Division of the State Architect (DSA): Field Act & Public K-12/Community College Oversight 8.2 Department of Health Care Access and Information (HCAI): Alfred E. Alquist Act & Healthcare Facility Classification 8.3 Essential Services Buildings Seismic Safety Act (ESBSSA) & California Historical Building Code (CHBC)
9 Chapter 9: California Building Code (CBC Title 24 Part 2) Core Architecture Provisions
9.1 Occupancy Classifications, Building Heights, and Allowable Floor Areas (CBC Chapters 3 & 5) 9.2 Fire and Smoke Protection Features, Fire Barriers, and Fire-Resistance Ratings (CBC Chapter 7) 9.3 Means of Egress, Occupant Load Calculations, and Exit Separation (CBC Chapter 10) 9.4 California Health and Safety Code: Building Standards Law, State Housing Law & Health Mandates
10 Chapter 10: Accessibility Requirements: Title 24 Chapter 11B & ADA
10.1 California Accessibility Framework: CBC Chapter 11B vs Federal ADA Standards 10.2 Accessible Routes, Entrances, Parking, and Site Arrival Points 10.3 Accessible Restrooms, Signage, Scoping, and Path of Travel Alteration Thresholds
11 Chapter 11: California Site Conditions & Natural Hazards
11.1 Seismic Hazard Mapping: Alquist-Priolo Earthquake Fault Zoning Act & Liquefaction 11.2 Wildland-Urban Interface (WUI) & Fire Hazard Severity Zones (CBC Chapter 7A & CFC Part 9) 11.3 Flood Hazard Zones (FEMA/DWR) & California Wind Exposure Categories
12 Chapter 12: Energy Efficiency: California Energy Code (Title 24 Part 6)
12.1 Energy Code Compliance Approaches: Prescriptive vs Performance & Time Dependent Valuation (TDV) 12.2 Mandatory Energy Measures: Envelope, HVAC, Lighting, Solar PV & Energy Storage Systems
13 Chapter 13: Sustainability (CALGreen) & Systems Integration
13.1 CALGreen (Title 24 Part 11) Mandatory Nonresidential & Residential Green Building Measures 13.2 Life-Cycle Cost Analysis (LCCA) & Value Engineering in California Practice 13.3 Building Systems Integration: MEP Coordination, Materials Evaluation & Acoustic Control
14 Chapter 14: Construction Document Requirements & Regulatory Coordination
14.1 CD Content, Detailing & Inter-Disciplinary Coordination for Agency Approval and Bidding 14.2 Authority Having Jurisdiction (AHJ) Hierarchy, Local Amendments & Local Finding Requirements 14.3 Reconciling Conflicting Codes, Standards, and Regulatory Mandates
15 Chapter 15: Plan Check & Permitting Processes
15.1 Permitting Procedures, Plan Check Review, Agency Comment Inquiries & Approval Pathways 15.2 Phased Permitting, Deferred Approvals, Encroachment Permits & Public Right-of-Way Coordination
16 Chapter 16: California Public Contract Code & Bidding Procedures
16.1 Public Works Bidding, Competitive Bidding Thresholds & Responsive vs Responsible Bidders 16.2 Subletting and Subcontracting Fair Practices Act & Subcontractor Listing Rules (PCC §§ 4100–4114) 16.3 California Prevailing Wage Requirements, DIR Registration & Certified Payroll Records
17 Chapter 17: California Mechanics Lien Law & Payment Remedies
17.1 20-Day Preliminary Notice Requirements & Timing (Civil Code § 8200) 17.2 Mechanics Liens, Recording Deadlines & Impact of Notice of Completion (Civil Code §§ 8400–8494) 17.3 Stop Payment Notices, Payment Bonds & Design Professional Liens (Civil Code §§ 8300–8319, 9350–9566)
18 Chapter 18: Construction Administration: Pre-Construction, Submittals, Changes & Field Observation
18.1 Pre-Construction & Pre-Installation Meetings and the Construction Manager's Impact on Services 18.2 Shop Drawings, Submittals & Architect's Deferred Submittal Review and Stamp 18.3 Construction Changes: Change Orders (CO), CCDs, ASIs & DSA Category A/B CCDs 18.4 Periodic Site Observations, Field Reports & the Means-and-Methods Boundary
19 Chapter 19: Inspection, Close-Out & Post-Construction Services
19.1 Special Inspections, Testing (CBC Chapter 17) & DSA/HCAI Continuous Field Inspection 19.2 Project Close-Out, Payment Applications (G702/G703), Retainage & California Warranty/Defect Limitations (CCP §§ 337.1 & 337.15) 19.3 Post-Construction Services, Record Documents & the Warranty Period 19.4 Construction Industry Standards, Detailing & Referenced Standards
8.1 Division of the State Architect (DSA): Field Act & Public K-12/Community College Oversight
Key Takeaways Explain This Topic AI
The Field Act of 1933 (Education Code §§ 17280–17316 for K-12; §§ 81130–81147 for Community Colleges) establishes mandatory state-level seismic and structural design standards for California public schools.
The Division of the State Architect (DSA) exercises exclusive plan review and construction enforcement across three core regulatory pillars: Structural Safety (SS), Fire and Life Safety (FLS), and Accessibility (ACS).
Continuous on-site inspection must be performed by a DSA-certified Project Inspector (Inspector of Record - IOR) employed directly by the school district governing board, never by the general contractor.
Construction Change Documents (CCDs) are bifurcated under IR A-6: Category A changes (affecting SS, FLS, or ACS) require DSA pre-approval prior to construction, while Category B changes (minor non-safety modifications) do not require prior approval.
Final project certification requires semi-annual and final Verified Reports (Form DSA-6 series) submitted under penalty of perjury by the architect, structural engineer, project inspector, and contractor.
Last updated: September 2026
Division of the State Architect (DSA): Field Act & Public K-12/Community College Oversight
Public school architecture in California occupies a uniquely rigorous regulatory environment. Unlike standard commercial or residential structures permitted by municipal or county building departments, public educational facilities are governed by state-level legislation designed to guarantee extraordinary structural resilience and student life safety. Candidates preparing for the California Supplemental Examination (CSE) must master the administrative procedures, legal mandates, and oversight roles enforced by the Division of the State Architect (DSA) under the historic Field Act of 1933 .
The Field Act of 1933: Historical and Statutory Foundation
On March 10, 1933, the magnitude 6.4 Long Beach earthquake devastated Southern California, destroying or severely damaging more than 230 school buildings. Because the earthquake struck at 5:54 PM when classrooms were vacant, catastrophic casualties among children were averted. Recognizing that unreinforced masonry school buildings would have caused thousands of student deaths had the tremor struck during school hours, the California Legislature acted with unprecedented speed. Within thirty days, Assemblyman C. Don Field authored, and Governor James Rolph signed into law, the Field Act of 1933 .
The Field Act established a permanent statewide mandate requiring that all public school buildings be designed and constructed to resist severe seismic lateral forces. The statute is codified in the California Education Code under two primary divisions:
K-12 Public Schools: California Education Code §§ 17280–17316.
Community Colleges: California Education Code §§ 81130–81147.
Jurisdictional Scope & Critical Exclusions
DSA exercises direct plan review and construction enforcement authority over:
All public elementary, middle, and high school districts (K-12).
All California Community College districts.
State-owned or state-leased essential services buildings.
Critical Distinction for the CSE: The Field Act applies strictly to public school districts and community colleges . It does not govern private schools, parochial schools, or charter schools occupying private non-district facilities. Furthermore, the four-year public university systems—the University of California (UC) and California State University (CSU) —are legally exempt from DSA Field Act plan review. UC and CSU campuses operate under independent seismic policies and maintain campus building officials, though DSA retains jurisdiction over state accessibility compliance (DSA-ACS) on university properties.
The Three Pillars of DSA Plan Review
Operating within the California Department of General Services (DGS), the DSA functions as the Authority Having Jurisdiction (AHJ) for covered educational construction. A complete DSA plan approval requires compliance across three fundamental disciplines, known colloquially as the Three Pillars of DSA Review :
Structural Safety (SS): Direct structural engineering evaluation enforcing the California Building Code (CCR Title 24, Part 2) with specialized amendments in Chapter 16A and 17A. Review encompasses gravity framing, lateral force-resisting systems, foundation geotechnical reports, and dynamic seismic drift limitations.
Fire and Life Safety (FLS): Enforces fire-resistive construction, spatial separation, allowable building areas, occupancy loads, egress geometry, automatic fire sprinkler systems, and fire alarm notification systems. DSA exercises this review through statutory authority delegated by the Office of the State Fire Marshal (OSFM) under CCR Title 24, Part 9.
Accessibility (Access / ACS): Enforces universal barrier-free physical and sensory accessibility under CCR Title 24, Part 2, Chapter 11B, coordinating California building standards with Title II of the federal Americans with Disabilities Act (ADA). DSA review covers accessible approaches, exterior paths of travel, parking, entrances, door clearances, restrooms, drinking fountains, assistive listening systems, and specialized educational casework.
Title 24, Part 1, Chapter 4: Administrative Regulations
CCR Title 24, Part 1, Chapter 4 governs the administrative lifecycle of public school construction. The administrative rules establish clear lines of legal liability and procedural checkpoints that architects must execute:
The Architect in General Responsible Charge
Pursuant to Title 24, Part 1, Section 4-316, all drawings, specifications, and structural calculations must be prepared under the direct supervision of a California-licensed architect or structural engineer. When multiple consultants collaborate (civil, structural, mechanical, electrical), one primary professional must be formally designated on the application (Form DSA-1) as the Architect or Engineer in General Responsible Charge .
The Architect in General Responsible Charge retains statutory duty to:
Coordinate all engineering disciplines and ensure complete cross-disciplinary drawing reconciliation.
Submit all plans, change documents, and technical addenda to DSA for review.
Provide general personal observation of construction progress at appropriate construction milestones.
Prepare and execute verified reports under penalty of perjury.
The Project Inspector (Inspector of Record - IOR)
A foundational tenet of the Field Act is that quality construction requires continuous, unbiased oversight. Under CCR Title 24, Part 1, Section 4-333 and Section 4-342, construction must be inspected by an independent, DSA-certified Project Inspector (often termed the Inspector of Record, or IOR).
Certification Classes
DSA certifies project inspectors through rigorous examinations into four distinct classifications:
Class 1: Qualified to inspect all types of public school construction, including multi-story structural steel and complex concrete shear wall buildings.
Class 2: Qualified to inspect all building types except high-rise structural steel or complex structures.
Class 3: Limited to single-story wood frame, light gauge steel, and masonry construction.
Class 4: Specialized in relocatable modular classrooms and shade structures.
Mandatory Direct Board Employment (The Independence Rule)
The Education Code explicitly mandates that the Project Inspector must be employed and compensated directly by the school district governing board (Form DSA-5-P). The IOR must never be employed, subcontracted, or compensated by the general contractor, construction manager, or testing laboratory. This absolute institutional separation ensures that the inspector remains immune to commercial pressures regarding project schedule or construction costs.
Continuous Inspection Duties
The IOR must provide continuous inspection of all construction operations. If the project architect or structural engineer specifies concrete rebar placement, structural welding, or masonry grouting, the work cannot be covered or poured until the IOR physically verifies compliance with the DSA-approved documents. The inspector maintains a continuous daily job log (Form DSA-152, Project Inspection Card), issues formal notifications of non-compliant work to the contractor, and files semi-annual and final verified reports.
Construction Change Documents (CCDs): Category A vs. Category B
During school construction, deviations from approved drawings frequently arise due to unforeseen site conditions, material substitutions, or design clarifications. Under DSA Interpretation of Regulations IR A-6 , modifications are strictly classified as either Category A or Category B Construction Change Documents:
Classification Definition & Scope DSA Approval Timing Impact on Construction
Category A (CCD-A) Changes affecting Structural Safety (SS), Fire & Life Safety (FLS), or Accessibility (ACS) . Examples: modifying structural framing, altering shear walls, reconfiguring exit corridors, moving fire alarm panels, or changing door threshold slopes. Mandatory Pre-Approval: Must be formally submitted to DSA and stamped "Approved" prior to commencing the affected work . Contractor cannot proceed with work until DSA signs off; unapproved work risks stop-work notices and certification denial.
Category B (CCD-B) Changes not affecting SS, FLS, or ACS. Examples: changing paint colors, modifying non-rated cabinetry finishes, shifting non-bearing millwork, or minor plumbing fixture brand substitutions. Informational Record: Submitted to DSA for record filing; does not require DSA pre-approval prior to construction. Work may proceed immediately upon sign-off by the Architect in General Responsible Charge and School District.
Form DSA-6: Mandatory Verified Reports & Closeout Certification
Under Education Code § 17309 and CCR Title 24 Part 1 § 4-336, construction cannot be deemed legally certified until all primary project participants file sworn Verified Reports (Form DSA-6 series) . These reports state under penalty of perjury that all work was performed in strict accordance with the DSA-approved plans and specifications.
Who Must File Form DSA-6?
Form DSA-6-AE: Architect and Structural Engineer of Record.
Form DSA-6-PI: Project Inspector of Record (IOR).
Form DSA-6-C: General Contractor and specialty subcontractors.
Verified reports must be submitted:
Semi-annually during the active life of the project.
Immediately when work is suspended for more than one month.
When any professional, inspector, or contractor is relieved, terminated, or substituted.
Upon final completion of the construction contract.
Upon receipt of all verified reports, complete testing laboratory reports (Form DSA-291), and verified inspector closeout cards (Form DSA-152), DSA issues a formal Certification Letter (Form DSA-102 or DSA-179) . If a school district occupies a building without DSA certification, the state issues a formal Notice of Non-Certification, creating significant legal exposure and insurance vulnerabilities for the district board.
Pre-Check (PC) and Alteration Thresholds
To streamline school construction, DSA maintains specialized procedural pathways for standardized structures and minor modernizations:
Pre-Check (PC) Approval: Manufacturers and architects may submit standard designs for relocatable classrooms, modular buildings, and shade canopies for statewide DSA "Pre-Check" approval. When a district purchases a PC design, DSA plan review is confined strictly to site-specific conditions (soil foundations, utility hookups, and accessible paths of travel), drastically cutting plan check timelines.
Rehabilitation and Alteration Thresholds (IR A-10 / IR A-22): For existing school modernizations, statutory valuation thresholds determine whether full structural or accessibility upgrades are triggered. Under Education Code § 17280(a), minor maintenance or alterations costing less than statutory thresholds (indexed annually) that do not affect structural members or fire/life safety may proceed without prior DSA plan review, provided work complies with code standards.
Table: DSA Project Roles, Forms, and Submittal Workflows
Project Role Governing Authority Key Statutory Responsibility Primary DSA Forms
School District Board California Education Code Project Owner; enters contracts; directly employs Project Inspector and geotechnical testing lab. DSA-1 (Application), DSA-5-P (Inspector Employment)
Architect in General Responsible Charge CCR Title 24 Part 1 § 4-316 Prepares design; coordinates consultants; submits CCDs; conducts periodic field observation; files verified reports. DSA-1 (Submittal), CCD-A / CCD-B, DSA-6-AE (Verified Report)
Structural Engineer of Record (SE) CCR Title 24 Part 1 § 4-317 Designs structural and lateral force-resisting systems; reviews structural shop drawings; conducts periodic field observation. Delegated Design Submittals, DSA-6-AE
Project Inspector (IOR) CCR Title 24 Part 1 § 4-333 Certified by DSA; provides continuous on-site inspection; verifies compliance; maintains inspection card and job logs. DSA-152 (Inspection Card), DSA-6-PI (Verified Report)
General Contractor CCR Title 24 Part 1 § 4-343 Constructs facility per approved plans; executes CCD work only after required approvals; files verified reports. DSA-6-C (Verified Report)
DSA Field Engineer CCR Title 24 Part 1 § 4-334 Conducts periodic field surveillance visits; reviews IOR records; verifies CCD-A approvals; issues stop-work orders if required. Field Surveillance Reports, DSA-102 (Certification)
CSE Exam Traps & Practical Takeaways
Trap 1: Charter and University Jurisdictions: Do not assume all public education falls under DSA Field Act review. UC and CSU campuses are exempt from Field Act structural plan check. Similarly, charter schools operating in privately leased commercial facilities are permitted through local municipal building departments unless the school district owns or builds the facility.
Trap 2: Inspector Contracting: A common exam scenario features a general contractor offering to subcontract the Project Inspector to "streamline site communication." This is illegal under the Field Act. The IOR must be under direct, independent contract with the school district governing board.
Trap 3: Proceeding with CCD-A Work: Contractors often pressure architects to allow structural or egress work to proceed while a Category A Construction Change Document is "under review at DSA." An architect must never authorize construction of CCD-A modifications prior to written DSA approval. Doing so violates Title 24 Part 1 and jeopardizes final certification.
Trap 4: Verified Reports Under Penalty of Perjury: Form DSA-6 is not a standard AIA certificate of substantial completion. It is a sworn statutory statement executed under penalty of perjury. An architect cannot sign a DSA-6 if unresolved code deviations or unapproved Category A changes remain uncertified in the field.