Study guide
10.3 Compound and Reverse Curves
California Civil Engineering Surveying CES
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 California Civil PE Path and Scheduling 1.3 Test Day, References, and Calculators
2 Chapter 2: Civil Engineer Surveying Authority
2.1 Professional Engineers Act: Engineering Surveying 2.2 Civil Engineer vs Professional Land Surveyor Limits 2.3 Board Rules, Accuracy Statements, and Map Act Context
3 Chapter 3: Survey Types and Control
3.1 Control Surveys: Purpose and Procedures 3.2 Alignment and Route Surveys 3.3 Topographic Surveys: Aerial, Surface, and Utilities
4 Chapter 4: Data Collection Methods, Accuracy, and GIS
4.1 Data Collection Methods: Leveling and LiDAR 4.2 Accuracy, Precision, and Error Types 4.3 GIS Applications for Civil Engineering Surveys
5 Chapter 5: Horizontal and Vertical Datums
5.1 Horizontal Datums and Assumed Systems 5.2 Vertical Datums and Benchmarks 5.3 Control Networks and Datum Selection
6 Chapter 6: Field Distances, Angles, and Conflicts
6.1 Measuring Horizontal Distances 6.2 Measuring Angles and Establishing Points 6.3 Construction Conflicts: Utilities, Structures, and Substructures
7 Chapter 7: Field Leveling and Equipment
7.1 Differential Leveling and Level Notes 7.2 Trigonometric Leveling 7.3 Surveying Equipment: Distance, Angle, Elevation
8 Chapter 8: Traverse and Rectangular Coordinates
8.1 Latitudes, Departures, and Coordinates 8.2 Error of Closure 8.3 Traverse Adjustment and Side Shots
9 Chapter 9: Angles, Distances, and Equipment Errors
9.1 Azimuths, Bearings, Backbearings, and Deflections 9.2 Horizontal, Slope, and Vertical Distances 9.3 Equipment Errors and Corrections
10 Chapter 10: Horizontal Curves
10.1 Circular Curve Elements 10.2 Horizontal Curve Stationing and Layout 10.3 Compound and Reverse Curves
11 Chapter 11: Vertical Curves and Line and Grade
11.1 Vertical Curve Geometry and Grades 11.2 High and Low Points and Intermediate Elevations 11.3 Line and Grade from Plans and Profiles
12 Chapter 12: Contours, Offsets, Areas, and Earthwork
12.1 Contours and Cross-Sections 12.2 Offsets and Vertical Interference 12.3 Areas, DMD, and Earthwork Volumes
13 Chapter 13: Mapping
13.1 Interpreting Maps and Plans 13.2 Interpolating Elevations and Plotting Features 13.3 Map Scales and Accuracy Standards
14 Chapter 14: Construction Staking and Cross-Sections
14.1 Stationing and Stake Marking 14.2 Hinge Points, Catch Points, and Grade Breaks 14.3 Slope Staking from Typical Sections
15 Chapter 15: Construction Alignment Layout
15.1 Staking Horizontal Alignment and Curves 15.2 Staking Vertical Alignment and Grades 15.3 Mixed Layout Problems and Exam Strategy
10.3 Compound and Reverse Curves
Key Takeaways Explain This Topic AI
A compound curve is two same-hand arcs meeting at a PCC with centers |R1 − R2| apart; a reverse curve is opposite-hand, meeting at a PRC with centers R1 + R2 apart.
For R1 = 600 ft, Δ1 = 24°, R2 = 400 ft, and Δ2 = 18°, L1 = 251.33 ft, L2 = 125.66 ft, Ta = 215.69 ft, and Tb = 179.39 ft — not the simple-curve value 600 tan 21° = 230.32 ft.
Equal-radius reverse curves R = 200 ft connecting parallel centerlines 80.00 ft apart have Δ = 36°52'12" on each arc and L = 128.70 ft each.
Compound curves are the everyday ramp tool; reverse S-curves appear on offset streets; high-speed reverse usually needs a tangent between the arcs for superelevation runoff.
The standing CES trap is applying T = R tan(I/2) to a compound as if it were one simple curve.
Last updated: September 2026
A simple curve has one radius. Domain III.E of the CES test plan also names compound and reverse curves. Both are two circular arcs sharing a common tangent at the junction, but they differ in hand (direction of curvature) and in the distance between centers. The exam trap is to grab T = R tan(Δ/2) as if the whole alignment were one simple curve.
- Same-hand compound vs opposite-hand reverse
- Compound curves (same direction)
A compound curve joins two (or more) circular arcs that turn the same way , with different radii, meeting at the point of compound curvature (PCC) . At the PCC the two arcs share a common tangent and a common radial line. Centers O1, O2, and the PCC are collinear, and
O1O2 = |R1 − R2| .
Total intersection angle of the combined alignment is I = Δ1 + Δ2 .
Each arc still has its own simple-curve length:
L1 = R1 Δ1 π / 180, L2 = R2 Δ2 π / 180, L = L1 + L2 .
What is not simple is the overall tangent from the PC to the combined PI, or from that PI to the PT. Those incoming and outgoing tangents Ta and Tb are unequal when R1 ≠ R2. They are not T = R1 tan(I/2), not T = R2 tan(I/2), and not T = R_avg tan(I/2). Each local arc would have its own mini-PI if you treated it as a standalone simple curve (t1 = R1 tan(Δ1/2), t2 = R2 tan(Δ2/2)), and those local tangent lengths are also not Ta and Tb.
- Place the PC at the origin with the incoming tangent along +x. Then, with I = Δ1 + Δ2,
- PTy = R1 − (R1 − R2) cos Δ1 − R2 cos I
- PTx = (R1 − R2) sin Δ1 + R2 sin I
- Ta = PTx − PTy / tan I
- Tb = PTy / sin I
Those two-center formulas are the replacement for T = R tan(I/2). Stationing still uses PC = PI − Ta and PT = PC + L1 + L2, never PI + Tb as a station.
Worked compound layout: R1 = 600 ft, Δ1 = 24°00', R2 = 400 ft, Δ2 = 18°00'
Place the larger radius first (common on ramps that tighten). I = 42°00'.
- L1 = 600 × 24 × π / 180 = 251.33 ft
- L2 = 400 × 18 × π / 180 = 125.66 ft
- L = 376.99 ft
Local simple tangents (not the overall PI tangents):
- t1 = 600 tan 12° = 127.53 ft
- t2 = 400 tan 9° = 63.35 ft
Two-center geometry for the combined PI:
- Ta = 215.69 ft (PC to PI along the back tangent)
- Tb = 179.39 ft (PI to PT along the forward tangent)
The trap value T = R1 tan(I/2) = 600 tan 21° = 230.32 ft is 14.63 ft too long on the incoming side. The average-radius fake T = 500 tan 21° = 191.93 ft is too short. Either error shifts every station.
Station the curve from a PI at 30+00.00:
- PC = 30+00.00 − 2+15.69 = 27+84.31
- PCC = 27+84.31 + 2+51.33 = 30+35.64
- PT = 30+35.64 + 1+25.66 = 31+61.30
Check: PC + L = 27+84.31 + 3+76.99 = 31+61.30. Note that PI + Tb = 30+00 + 1+79.39 = 31+79.39, which is not the PT station — the same PI+T trap, now with unequal Ta and Tb.
Arc degrees: D1 = 5729.58 / 600 = 9.549° , D2 = 5729.58 / 400 = 14.324° . The alignment gets sharper after the PCC, which is the usual ramp story: a large-radius entrance compounds into a smaller-radius turning roadway.
Reverse curves (opposite direction)
A reverse curve joins two circular arcs that turn opposite ways, meeting at the point of reverse curvature (PRC) or with a short tangent between. At a direct PRC the arcs share a common tangent, the hand flips, centers O1, O2, and the PRC are collinear, and
O1O2 = R1 + R2 .
Net direction change of the alignment is |Δ1 − Δ2| when the two deflections partly cancel. Connecting parallel tangents requires Δ1 = Δ2 = Δ, and the offset between those tangents is
p = R1(1 − cos Δ) + R2(1 − cos Δ) = (R1 + R2)(1 − cos Δ) .
Worked reverse layout: parallel streets, equal radii
Two parallel street centerlines are 80.00 ft apart. Connect them with a reverse pair of equal-radius arcs, R1 = R2 = 200.00 ft , meeting at a PRC (no intermediate tangent).
- p = 2 R (1 − cos Δ) = 80.00
- 1 − cos Δ = 80 / 400 = 0.20
- cos Δ = 0.80
- Δ = arccos(0.80) = 36.8699° = 36°52'12" (the 3-4-5 angle: sin Δ = 0.60, tan Δ = 0.75)
Each arc: L = 200 × 36.8699 × π / 180 = 128.70 ft Each simple tangent: T = 200 tan(18°26'06") = 200 × 1/3 = 66.67 ft Total centerline through both arcs: 257.40 ft Offset check: 400 (1 − 0.80) = 80.00 ft.
If the street design inserts a 120-ft internal tangent between PT1 and PC2 — the usual highway preference — you no longer have a single PRC. Each arc is then an ordinary simple curve with its own PC, PI, and PT, and stationing adds the 120-ft tangent between PT1 and PC2. Example: R1 = 400 ft, R2 = 350 ft, Δ = 20°00' each, connecting tangent 120.00 ft:
- T1 = 400 tan 10° = 70.53 ft , L1 = 139.63 ft
- T2 = 350 tan 10° = 61.71 ft , L2 = 122.17 ft
Occupied centerline from PC1 to PT2 = L1 + 120.00 + L2 = 381.80 ft (the approach T1 and exit T2 sit outside that run)
Streets vs ramps
Setting Typical curve Why
Local / collector streets Reverse (S-curve) to pick up an offset, a dog-leg, or a parking-aisle shift Low speed; parallel-street connections are common
Arterial that must tighten between controls Compound Fit a changing radius between right-of-way pins
Freeway ramps and loops Compound, often large R then small R Match high-speed entry to a tighter turning roadway
High-speed reverse Avoid a bare PRC; insert a tangent Needs length for superelevation to run down, through zero, and up the other way
Caltrans-style highway practice generally does not like a reverse pair with no tangent between at highway speed. Direct PRC reverse curves still appear on slow streets, site drives, and some ramp gore geometry. Compound curves are the everyday ramp tool and appear on channelized intersection returns.
Exam traps
Simple T on a compound. T = R tan(I/2) using R1, R2, or an average is wrong for Ta and Tb. Use two-center Ta, Tb, then station from PC through PCC to PT.
Using O1O2 = |R1 − R2| on a reverse. Reverse centers are R1 + R2 apart.
Forgetting the hand change. Compound: Δ1 + Δ2 add. Reverse: they oppose.
Stationing through the combined PI. Same rule as Section 10.2: PC = PI − Ta, PT = PC + L1 + L2, not PI + Tb.
Degree-of-curve mix. Each arc has its own D = 5729.58 / R. There is no single D for a compound.
If a CES stem gives only one R and one Δ, it is a simple curve. If it names a PCC or two radii in the same direction, it is compound. If it names a PRC, an S-curve, or opposite deflection, it is reverse. Draw O, the common radius through the junction, and the two tangents before you pick a formula.