Study guide
Overpacks, Salvage Packaging & Pressure Differential Standards
IATA Dangerous Goods Regulations Air
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: General Philosophy, Applicability & CBTA Framework
Legal Basis & International Regulatory Framework Shipper & Operator Responsibilities in Air Transport Competency-Based Training & Assessment (CBTA) & Certification Categories Dangerous Goods Security & High Consequence Dangerous Goods
2 Chapter 2: Dangerous Goods Limitations
Forbidden Dangerous Goods & Hidden Dangerous Goods Recognition Passenger & Crew Baggage Provisions (Section 2.3 Provisions Table) State Variations & Operator Variations (Sections 2.8 and 2.9) Excepted Quantities (EQ) & Limited Quantities (LQ) Provisions Operators' Own Property (COMAT) & Dangerous Goods in Air Mail
3 Chapter 3: Classification of the 9 Hazard Classes
Class 1 (Explosives) & Class 2 (Gases) Classification Class 3 (Flammable Liquids) & Class 4 (Flammable Solids, Spontaneous Combustibles, Dangerous When Wet) Class 5 (Oxidizing Substances & Organic Peroxides) & Class 6 (Toxic & Infectious Substances) Class 7 (Radioactive Material) Basics, Activity Limits & Radiation Protection Class 8 (Corrosives) & Class 9 (Miscellaneous Dangerous Goods & Environmentally Hazardous) Packing Groups (PG I, II, III) & Precedence of Hazards Matrix
4 Chapter 4: Identification & List of Dangerous Goods
Navigating Section 4.2 (Blue Pages & Table Columns A–N) Proper Shipping Names, UN/ID Numbers & Technical Name Rules Special Provisions (Section 4.4) & Mixture/Solution Rules Lithium Batteries Identification & Classification (UN 3090, 3091, 3480, 3481) Section 4.3 Numerical Cross-Reference & the End-to-End Lookup Workflow
5 Chapter 5: Packing Requirements & UN Specification Packaging
General Packing Requirements, Single vs. Combination Packaging & Ullage Rules Packing Instructions (PI) Selection & Quantity Limitations UN Specification Packaging Codes & Performance Tests (Drop, Stacking, Hydraulic Pressure) Overpacks, Salvage Packaging & Pressure Differential Standards Dry Ice, Consumer Commodity (ID 8000) & Class-Specific Packing Provisions Infectious Substances in Practice: Packing Instruction 620 and Packing Instruction 650
6 Chapter 6: Marking & Labelling Requirements
DGR 7.1 — Package Marking Requirements DGR 7.2 — Hazard Class & Subsidiary Risk Labels (Specifications & Placement Rules) DGR 7.2 — Handling Labels (Cargo Aircraft Only, Orientation Arrows, Magnetized Material, Cryogenic) DGR 7.1 — Lithium Battery, Excepted Quantity & Limited Quantity Marks
7 Chapter 7: Dangerous Goods Documentation
DGR 8.1 — Shipper's Declaration for Dangerous Goods (SDDG): Structure & Completion Rules DGR 8.2 — Air Waybill Handling Information & Non-Dangerous Goods Declarations DGR Section 8 — Electronic Shipper's Declaration (e-DGD) & Documentation Retention
8 Chapter 8: Stowage, Handling & Emergency Procedures
Cargo Acceptance Checks & Acceptance Checklist Verification Loading Limitations, Cargo Aircraft Only (CAO) & ULD Rules Segregation & Incompatibility Rules (Table 9.3.A Segregation Matrix) Notification to Captain (NOTOC) & Pilot-in-Command Information Dangerous Goods Incidents, Reporting & Emergency Response Procedures Class 7 Radioactive Material: Section 10 Packing, Labelling, Documentation & Stowage
Overpacks, Salvage Packaging & Pressure Differential Standards
Key Takeaways Explain This Topic AI
An overpack is an enclosure used by a single shipper to consolidate one or more fully compliant packages into a single handling unit for convenience or protection.
Overpacks must be marked with the word 'OVERPACK' (minimum 12 mm height) and duplicate all inner package PSNs, UN numbers, hazard labels, and orientation arrows unless visible.
Salvage packagings are special UN certified containers marked with the letter 'T' (e.g., 1A2T) used to transport damaged, leaking, or defective dangerous goods packages.
All inner packagings (and single packagings) containing liquid dangerous goods in air transport must withstand an internal pressure differential of not less than 95 kPa without leaking.
Incompatible dangerous goods requiring segregation under DGR Table 9.3.A must never be combined within the same overpack.
Last updated: August 2026
Overpacks, Salvage Packaging & Pressure Differential Standards
Beyond standard individual packages, air cargo operations frequently utilize specialized packaging configurations to streamline handling, protect cargo, or manage damaged packages. Understanding the legal definitions, marking rules, and pressure standards for overpacks , salvage packagings , and pressure differential compliance is critical for dangerous goods certification.
1. Overpacks: Definition, Rules & Construction
An overpack is defined under IATA DGR Section 5.0.1.5 as an enclosure used by a single shipper to contain one or more dangerous goods packages to form a single handling unit for convenience of handling and stowage. Examples include a shrink-wrapped wooden pallet, a plastic stretch-wrapped crate, or a large protective outer box. +-------------------------------------------------------------------------+
- | OVERPACK CONFIGURATION |
- | |
- | +-------------------------------------------------------------------+ |
- | | OVERPACK ENCLOSURE | |
- | | Markings: "OVERPACK" (12 mm min), PSN, UN ####, Labels, Arrows | |
- | | | |
- | | +-----------------------+ +-----------------------+ | |
- | | | Compliant Package 1 | | Compliant Package 2 | | |
- | | | UN 1263 Paint (4G) | | UN 1263 Paint (4G) | | |
- | | +-----------------------+ +-----------------------+ | |
- | +-------------------------------------------------------------------+ |
- +-------------------------------------------------------------------------+
- Fundamental Overpack Rules
Independent Compliance : An overpack is not an outer packaging of a combination package. Every individual package placed inside an overpack must independently meet all DGR packaging, UN specification testing, marking, labeling, and net quantity rules.
Segregation Compliance : Incompatible dangerous goods that require segregation under DGR Section 9.3.2 (Table 9.3.A) —such as Class 3 Flammable Liquids and Division 5.1 Oxidizers—must never be placed inside the same overpack.
Single Shipper Requirement : An overpack is by definition assembled by a single shipper . Packages from different shippers must not be combined into one overpack.
2. Overpack Marking and Labeling Requirements
Unless all marks and labels representative of every dangerous goods package inside the overpack are clearly visible from the exterior, the shipper must reproduce all required package markings and labels on the outside of the overpack.
Exterior Overpack Markings Checklist
The Word "OVERPACK" : Printed in lettering at least 12 mm (0.5 inches) high.
Proper Shipping Name (PSN) & UN Number : For every dangerous good contained within (e.g., UN 1263, Paint ).
Shipper & Consignee Information : Full name and physical address.
Hazard Warning Labels : Primary and subsidiary hazard labels for each package contained.
Handling Labels : Special handling labels such as Cargo Aircraft Only (CAO) or Environmentally Hazardous Substance labels.
Package Orientation Arrows ("THIS SIDE UP") : Placed on two opposite vertical sides of the overpack whenever liquid dangerous goods packages are enclosed.
Shipper's Declaration Documentation
When packages are tendered in an overpack, the Shipper's Declaration for Dangerous Goods (DGD) must explicitly include the notation "Overpack Used" adjacent to the package details, indicating to ground acceptance staff that packaging limits apply to individual inner packages within the overpack.
3. Salvage Packaging ('T' Marking & Operational Use)
When a dangerous goods package is found to be damaged, defective, leaking, or non-compliant during handling or transit, it cannot be loaded onto an aircraft in that condition. It must be safely enclosed within a salvage packaging .
UN Code Identification for Salvage Packaging
Salvage packagings are specially tested UN specification containers designated by the capital letter 'T' inserted immediately after the packaging type code: UN Mark Example: 1 A 2 T / Y300 / S / 26 / USA / +AA9876 \text{UN Mark Example: } \mathbf{1A2T \text{ / Y300 / S / 26 / USA / +AA9876}} UN Mark Example: 1A2T / Y300 / S / 26 / USA / +AA9876
1A2T : Removable-head steel drum specifically tested and certified as a salvage packaging .
1H2T : Removable-head plastic drum tested as a salvage packaging. Salvage Packaging Codes:
- Removable-head Steel Drum: 1A2T
- Removable-head Plastic Drum: 1H2T
- Operational Salvage Transport Procedures
Absorbent Placement : Sufficient inert absorbent material must be placed inside the salvage drum to surrounding the damaged inner package to absorb all free liquid.
Exterior Markings : The salvage drum must be marked with the Proper Shipping Name and UN number of the damaged substance, plus the word "SALVAGE" in bold lettering.
Documentation : The Shipper's Declaration must state "Salvage Package" in the quantity and type of packing section.
4. The Aviation Internal Pressure Differential Standard (95 kPa)
During flight, commercial aircraft cargo holds undergo cabin altitude pressure changes. As external ambient pressure drops, internal pressure inside sealed liquid containers pushes outward against container walls. Aircraft Ascent Profile & Internal Pressure Differential:
- Ground Level (101 kPa) --> Cruise Altitude (75 kPa Ambient Pressure)
- |====================================|
- | Sealed Liquid Container |
- | Internal Pressure: 170 kPa |
- | Differential: 170 - 75 = 95 kPa |
- |====================================|
- The Mandatory 95 kPa Rule
All inner packagings (or single packagings) intended to contain liquid dangerous goods for air transport must be capable of withstanding, without leaking, an internal pressure differential of: Required Internal Pressure Differential ≥ 95 kPa (13.8 psi / 0.95 bar) \text{Required Internal Pressure Differential} \ge 95 \text{ kPa (13.8 psi / 0.95 bar)} Required Internal Pressure Differential ≥ 95 kPa (13.8 psi / 0.95 bar)
Or a pressure derived from the total vapour pressure of the liquid at 55°C, whichever is greater . This requirement is independent of the packing group and applies to every liquid offered by air.
High Vapor Pressure & Low Pressure Exceptions
Packing Group I Liquids : The UN design-type hydraulic test for a PG I single packaging is at least 250 kPa , so such packagings comfortably exceed the 95 kPa air requirement. Do not confuse that design-type test pressure with the 95 kPa differential.
No lower alternative exists : 95 kPa is a floor, not a target. There is no reduced differential for short sectors, cargo aircraft, low-altitude routings, or non-viscous liquids — any figure below 95 kPa is a misreading.
Temperature Integrity Range : Pressure differential integrity must be maintained across ambient transport temperatures ranging from -40°C to +55°C (-40°F to +131°F) .