Study guide

9.2 Pesticide Application Techniques

California Structural Pest Control — Branch 2 General Pest Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Licensing, Laws, and SPCB Regulations

1.1 SPCB Board Rules, Licensing, and Field Rep Requirements 1.2 Recordkeeping, Reporting, and Disciplinary Procedures 1.3 SPCB vs. DPR vs. EPA: Regulatory Jurisdictions

2 Chapter 2: Structural Pest Identification: Cockroaches and Ants

2.1 Biology and Identification of California Pest Cockroaches 2.2 Biology, Trails, and Identification of California Ants 2.3 Metamorphosis and Basic Insect Anatomy

3 Chapter 3: Identification: Flying, Stinging, Fabric, and Stored Product Pests

3.1 Stinging and Biting Insects: Bees, Wasps, Hornets, Yellowjackets, and Bed Bugs 3.2 Flies, Gnats, and Occasional Invaders 3.3 Stored Product Pests and Fabric Pests

4 Chapter 4: Biology & Identification: Rodents and Vertebrate Pests

4.1 Commensal Rodents Biology and Habits 4.2 Signs of Rodent Infestation and Harborages 4.3 Birds and Other Vertebrate Pests

5 Chapter 5: Inspections, Monitoring, and Conducive Conditions

5.1 Customer Interviewing and Inspection Techniques 5.2 Identifying Conducive Conditions 5.3 Pest Monitoring Tools, Traps, and Thresholds

6 Chapter 6: Integrated Pest Management (IPM) & Treatment Planning

6.1 Principles and Steps of Integrated Pest Management 6.2 Mechanical, Cultural, Biological, and Physical Controls 6.3 Chemical Control Selection, Resistance Management, and Treatment Planning

7 Chapter 7: Pest Control Equipment, Maintenance, and Calibration

7.1 Application Equipment: Compressed Air Sprayers, Dusters, and Bait Guns 7.2 Equipment Maintenance and Troubleshooting 7.3 Equipment Calibration

8 Chapter 8: Pesticides, Formulations, Labels, and Calculations

8.1 Pesticide Formulations and Adjuvants 8.2 Deciphering the Pesticide Label 8.3 Dose, Dilution, and Area Application Calculations

9 Chapter 9: Treatment Preparation, Notification, and Application

9.1 Site Preparation, Customer Notification, and Chemical Safety 9.2 Pesticide Application Techniques 9.3 Post-Application Notice, Service Records, and Re-entry Directions

10 Chapter 10: Safety, Environmental Protection, and Personal Safety

10.1 Environmental Protection: Drift, Runoff, Water Protection, and Spill Response 10.2 Pesticide Storage, Transport, Container Disposal, and Waste Management 10.3 Personal Protection: Exposure Routes, PPE Requirements, and Respirator Programs 10.4 Symptoms of Pesticide Poisoning, First Aid, and Emergency Procedures

9.2 Pesticide Application Techniques

Key Takeaways Explain This Topic AI

DPR defines crack and crevice treatment as applying small amounts of insecticide directly into cracks and crevices where insects hide or enter; minimal pesticide should remain on the surface.

A spot treatment under DPR's definition is an application to limited areas that will not exceed two square feet, where pests are likely to occur or have been found.

For listed pyrethroids applied outdoors by pest control for hire, California allows a perimeter band of no more than 3 feet out from the building and no more than 2 feet up vertical surfaces (3 CCR 6970).

To prevent bait shyness and treatment failure, liquid or aerosol repellent sprays must never be applied on or near active bait stations.

Last updated: October 2026

  • 9.2 Pesticide Application Techniques
  • Precision Application

In structural pest control, application methods are as critical as active ingredients. California regulations prioritize target-specific techniques to minimize chemical volume, reduce environmental impact, and prevent occupant exposure. This section details crack and crevice, spot, perimeter, broadcast, and baiting treatments.

Crack and Crevice Treatment

A crack and crevice treatment is the application of small amounts of pesticide directly into openings where pests hide, nest, or enter structures.

Specifications and Equipment

Definition: DPR defines crack and crevice treatment as "the application of small amounts of insecticide directly into cracks and crevices in which insects hide or through which they may enter the building" (3 CCR 6000). Examples are openings at expansion joints, between different elements of construction, and between equipment and floors, and only minimal amounts of pesticide should remain on the surface. The definition sets no maximum gap width or pressure.

Application Pressure: Use the low pressure the label and equipment call for. High pressure causes splashing, blowback, and drift, contaminating non-target surfaces.

Nozzle Selection: Use a pin-stream nozzle or an injector tube tip (metal or plastic straw). A broad fan spray over the surface is not a crack and crevice treatment.

Importance in Pest Control

This technique is the primary method for controlling German cockroaches ( Blattella germanica ), bed bugs ( Cimex lectularius ), and ants. Because these pests hide in structural gaps, injecting pesticides into voids maximizes target contact and shields the chemical from sunlight and cleaning, extending residual life. Most importantly, it prevents contact with occupants and pets, making it suitable for schools and hospitals.

Spot Treatment

A spot treatment is a localized application of pesticide to a specific, limited surface area where pests walk or harbor.

Dimensional Limits and Restrictions

DPR defines a spot treatment as "an application to limited areas that will not exceed two square feet on which pests are likely to occur or have been located during the process of monitoring or inspection" (3 CCR 6000).

Maximum Spot Size: Any single treated spot must not exceed 2 square feet .

No Percentage Rule: The DPR definition sets no percentage-of-room limit; the label may add its own restrictions.

Application Areas: Spot treatments target baseboards, under appliances, behind sinks, and around door/window frames.

Technicians must measure treatment zones carefully. Covering an entire floor or wall with "multiple adjacent spot treatments" is no longer a spot treatment, and it violates any label that allows only spot or crack and crevice use.

Perimeter (Barrier) Treatment

A perimeter treatment is the application of pesticide around the exterior of a structure to prevent outdoor pests from invading.

Application Dimensions

Follow the label's band dimensions. For the pyrethroids listed in 3 CCR 6970 (such as bifenthrin, cypermethrin, deltamethrin, and permethrin) applied outdoors by pest control for hire, California sets these maximums:

Up the Foundation: A perimeter band on walls, foundations, and fencing may reach a maximum height of 2 feet above grade.

Out on the Soil: A perimeter band on soil, mulch, gravel, lawn, turf, or groundcover may be 3 feet wide or less from the base of the building outward.

Runoff and Environmental Hazards

Technicians must prevent drift and runoff from contaminating waterways.

Hardscapes: For listed pyrethroids, horizontal impervious surfaces such as driveways and patios, and windows and doors, may receive only spot, crack and crevice, or pin-stream (1 inch wide or less) treatments, and applications to storm drains, sewers, and curbside gutters are prohibited.

Weather: Listed pyrethroids may not be applied outdoors to any site during precipitation, except to the underside of eaves, or to surfaces with standing water (3 CCR 6970(e)). Follow any additional weather restriction on the label.

Broadcast Treatment

A broadcast treatment is the uniform application of pesticide over a broad, continuous surface area.

Branch 2 Restrictions

Broadcast applications are limited by the label:

Indoor: Allowed only where the label permits a broadcast or general surface use for the site and pest (for example, some flea products).

Outdoor: For listed pyrethroids, broadcast treatment of soil, lawn, turf, or groundcover is allowed but not within 2 feet of any horizontal impervious surface; only a pin stream of 1 inch or less may be made inside that 2-foot strip (3 CCR 6970(a)).

Baiting Strategies and Safety

Baiting relies on the target pest ingesting a pesticide formulation mixed with an attractive food source. Because baits must be consumed, placement and safety are paramount.

Placement and Safety

Foraging Paths: Baits must be placed directly in areas of pest activity, such as cockroach harborages or along ant trails.

Harborage Access: Focus placements in dark, warm, and humid areas: behind refrigerators, around plumbing pipes, and in cabinet corners.

Tamper-Resistant Stations: Rodenticide bait must be in tamper-resistant bait stations where children, pets, nontarget mammals, or birds may reach it, and in California almost all rodent bait used in and around structures must be in bait stations within 50 feet of a structure (UC IPM). Follow the label on securing stations. A rodenticide bait station must be marked with the label's signal word or symbols, the generic pesticide name, and the company's name, address, and telephone number (16 CCR 1983(i)).

Out of Reach: Loose gel or granular baits must be placed in cracks, crevices, or voids that are completely inaccessible to children and pets.

Avoiding Chemical Contamination

The Contamination Trap: Never apply liquid or aerosol repellent sprays on or near bait placements. Repellent chemicals contaminate the bait, making it unpalatable. Pests will avoid the bait, causing the treatment to fail.

Sequence of Service: If both liquid barriers and baits are used, apply liquids to the exterior perimeter and utilize non-repellent formulations or baits exclusively in indoor harborages.

  • Technique Spatial Definition / Dimension Key Equipment / Restriction
  • Crack & Crevice Small amounts into cracks and crevices (3 CCR 6000) Pin-stream/injector; low pressure
  • Spot Treatment Limited areas of 2 sq ft or less (3 CCR 6000) Low pressure; baseboards
  • Perimeter Pyrethroids: up to 2 ft up wall, up to 3 ft out (3 CCR 6970) Follow label band; no storm drains
  • Broadcast Wide continuous area Only where the label allows; pyrethroids not within 2 ft of hardscape
  • Baiting Localized target placement in harborages Keep away from repellents; use stations
  • Exam Traps and Real-World Scenarios

Exam Trap: The "Multiple Spots" Loophole. An applicator cannot apply multiple "2 square foot" spots right next to each other to cover an entire wall. That is no longer a spot treatment under DPR's definition (limited areas of 2 square feet or less), and it violates any label that allows only spot or crack and crevice use. Exam Trap: Bait Contamination. An exam question may describe a technician applying a synthetic pyrethroid spray (a known repellent) directly over a gel bait station to "speed up" cockroach control. This is incorrect practice because the repellent spray contaminates the bait, rendering the baiting program useless.