Study guide

ADAS Components: Sensors, Diagnosis & Calibration

Red Seal Automotive Service Technician Interprovincial Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the Red Seal Automotive Service Technician Exam

2 Safety & Common Occupational Skills

Shop Safety, Hoists & Personal Protective Equipment Hazardous Materials, WHMIS 2015 & Environmental Disposal Precision Measurement, Tools & Fasteners Communication, Mentoring & Service Documentation

3 Engines, Fuel & Emission Systems (Part A)

Section 3.1: Four-Stroke Engine Fundamentals & Mechanical Diagnostics Accessory Drive Systems: Belts, Tensioners & Pulleys Section 3.2: Fuel Delivery Systems: Gasoline Direct Injection (GDI) & Common-Rail Diesel (CRD) Section 3.3: Ignition Systems, Firing Orders & Combustion Diagnostics

4 Engines, Fuel & Emission Systems (Part B)

Cooling & Lubrication Systems Emission Control Systems: EVAP, EGR, Catalytic Converters & Diesel Controls Diesel Intake, Exhaust & Turbocharger Systems

5 Electrical & Electronic Systems (Part A)

Electrical Fundamentals, Ohm's Law & Circuit Calculations Battery Diagnostics & Starting/Charging System Testing Circuit Troubleshooting: Voltage Drop & Parasitic Draw Testing Circuit & Wiring Repair: Splices, Terminals & Harness Integrity

6 Electrical & Electronic Systems (Part B)

Electronic Components: Sensors, Actuators & Pulse-Width Modulation Vehicle Communication Networks & Multiplexing Programming, Immobilizers & Advanced Module Integration Lighting & Wiper Systems Diagnosis and Repair ADAS Components: Sensors, Diagnosis & Calibration

7 Drivetrain & Transmissions (Part A)

5.1 Clutch Systems & Manual Transmissions/Transaxles 5.2 Automatic Transmissions: Torque Converters & Planetary Gearsets 5.3 Continuously Variable Transmissions (CVT) & Hybrid Drivetrains

8 Drivetrain & Transmissions (Part B)

Section 5.4: Transfer Cases, 4WD/AWD Systems & Drive Axles Section 5.5: Differentials, Final Drives & Gear Setup

9 Brakes, Steering & Suspension (Part A)

Hydraulic Brake Systems & Master Cylinder/Caliper Service Anti-Lock Brakes (ABS), Traction/Stability Control & Wheel Speed Sensors Steering Systems & Electric Power Steering (EPS)

10 Brakes, Steering & Suspension (Part B)

Section 6.4: Suspension Systems & Component Diagnosis Section 6.5: Wheel Alignment Geometry & Correction Section 6.6: Tires, Wheels & Tire Pressure Monitoring Systems (TPMS)

11 HVAC, Restraints & Body Systems

7.1 A/C Refrigeration Cycle, R-1234yf & Refrigerant Service 7.2 Cabin Heating & Automatic Climate Control 7.3 Restraint Systems (SRS) & Body Electrical Accessories Body NVH: Wind Noise, Rattles & Water Leak Diagnosis Latches, Locks, Movable Glass & Body Trim

12 Hybrid & Electric Vehicle Systems

Hybrid & Electric Vehicle High-Voltage Systems High-Voltage Battery Diagnosis & Service

13 Diagnostics & Troubleshooting Strategy

Systematic Diagnostic Strategy & OBD-II Interface Oscilloscope Waveform Analysis & Intermittent Fault Diagnostics

ADAS Components: Sensors, Diagnosis & Calibration

Key Takeaways Explain This Topic AI

Forward-facing cameras handle lane keeping and traffic sign recognition, while radar sensors provide long-range object detection for adaptive cruise control and forward collision warning.

Static calibration is performed in-shop with targets and alignment fixtures; dynamic calibration requires driving the vehicle on marked roads so the module learns sensor orientation.

Windshield replacement, bumper R&R, wheel alignment, and ADAS module replacement all commonly require recalibration per manufacturer service information.

Misaligned ADAS sensors produce symptoms such as false collision warnings, lane departure alerts on straight roads, and adaptive cruise dropping out at highway speeds.

Steering angle sensor and wheel speed sensor data must be accurate before ADAS calibration; hybrid and EV service near ADAS modules requires high-voltage disable procedures and SRS precautions.

Last updated: July 2026

ADAS Components: Sensors, Diagnosis & Calibration

Advanced Driver Assistance Systems (ADAS) have become standard equipment on most vehicles sold in Canada. The Red Seal Automotive Service Technician occupational standard addresses ADAS under Tasks 14 (electrical/electronic accessories), 15 (HVAC and comfort systems integration), 18 (steering and suspension alignment effects), and 19 (brake and stability system interaction). Technicians must understand sensor types, calibration requirements, and the relationship between chassis geometry and ADAS accuracy.

ADAS Sensor Types and Roles

Modern ADAS platforms combine multiple sensor technologies, each optimized for specific detection ranges and conditions:

Sensor Type Typical Location Primary ADAS Functions

Forward camera Inside windshield, rearview mirror area Lane departure warning, lane keep assist, traffic sign recognition, pedestrian detection (with fusion)

Radar (24 GHz / 77 GHz) Front grille, bumper cover, or corner fascia Adaptive cruise control, forward collision warning, automatic emergency braking

  • Ultrasonic Bumper fascia (short range) Parking assist, low-speed obstacle detection
  • LiDAR Roof or bumper (emerging) High-resolution 3D mapping for autonomous features
  • Steering angle sensor Steering column or EPS module Lane keep assist, electronic stability control input
  • Wheel speed sensors Each wheel hub ABS, traction control, adaptive cruise speed matching

Sensor fusion combines data from multiple sources. For example, forward collision warning may use radar for distance measurement and camera for object classification (vehicle vs pedestrian vs stationary object). A fault in one sensor can disable multiple ADAS features because the system cannot verify data confidence.

  • Key ADAS Features
  • Forward Collision Warning / Automatic Emergency Braking (FCW/AEB)

Radar and/or camera monitors the road ahead. If closing speed indicates an imminent collision, the system warns the driver and may apply brakes autonomously. Misaligned forward radar causes false warnings or failure to detect vehicles ahead.

Lane Keep Assist / Lane Departure Warning (LKA/LDW)

The forward camera tracks lane markings. If the vehicle drifts without a turn signal, the system alerts the driver or applies gentle steering correction through the electric power steering (EPS) module. A camera knocked out of alignment during windshield replacement is the most common cause of erratic lane keep behaviour.

Blind Spot Monitoring (BSM)

Rear corner radar sensors detect vehicles in adjacent lanes. A warning icon illuminates in the side mirror. Bumper repairs or repainting without recalibration can shift radar aim.

Adaptive Cruise Control (ACC)

Front radar maintains a set following distance from the vehicle ahead by controlling throttle and brake application. Wheel speed sensor errors or radar misalignment cause the system to disengage unexpectedly.

Static vs Dynamic Calibration

Static calibration is performed in the shop with the vehicle stationary. It requires:

  • A level floor and correct vehicle ride height (full fuel tank or specified ballast per service information)
  • Manufacturer-specific calibration targets positioned at precise distances and heights from the sensor
  • Alignment fixtures, laser tools, or scan-tool-guided target placement
  • Correct tire pressure and no cargo load beyond specification

Dynamic calibration (also called on-road calibration or relearn ) requires driving the vehicle on well-marked roads at specified speeds for a set distance. The ADAS module uses known road geometry to adjust its internal aim parameters. Dynamic calibration is often performed after static calibration as a verification step, or as the sole method on some vehicle platforms.

  • Calibration Type Where Performed Equipment Needed Typical Duration
  • Static Service bay Targets, fixtures, scan tool 30–90 minutes
  • Dynamic Public road Scan tool, clear lane markings 15–30 minutes driving
  • Combined Bay then road Both Per manufacturer procedure
  • When Calibration Is Required

Calibration is not optional after certain repairs. Always consult the manufacturer's position statement and service information. Common triggers include:

  • Windshield replacement — forward camera mount is bonded to the glass
  • Front or rear bumper cover removal or replacement — radar and ultrasonic sensors mount behind the fascia
  • Wheel alignment — changes in toe, camber, or caster affect the vehicle's thrust angle relative to sensor aim
  • ADAS module R&R — camera, radar, or fusion module replacement
  • Collision repair — structural damage shifts sensor mounting points
  • Suspension component replacement — struts, control arms, or steering rack changes ride height or thrust angle
  • Steering angle sensor replacement — requires zero-point calibration

Skipping calibration after any of these services can leave ADAS features disabled, illuminate warning lamps, or worse—operate with incorrect aim, creating a safety hazard.

Scan-Tool Calibration Routines

OEM and aftermarket scan tools provide guided calibration routines that:

  • Verify preconditions (battery voltage above 12.4 V, correct tire pressure, no DTCs in related modules)
  • Confirm steering angle sensor center position
  • Walk the technician through target placement or road test parameters
  • Record calibration success or failure with timestamp

If calibration fails repeatedly, check for underlying faults before retrying: a bent radar bracket, windshield with incorrect tint band placement, or a steering angle sensor that has not been zeroed will cause calibration rejection.

Misalignment Symptoms

Technicians should recognize these customer complaints as potential ADAS calibration issues:

  • False forward collision warnings when no vehicle is ahead — forward radar aimed too high or too low
  • Lane departure alerts on straight highways — camera pitch or yaw out of specification

Adaptive cruise disengages at speed — radar obstruction (ice, mud, bumper cover distortion) or wheel speed sensor discrepancy

  • Blind spot warnings with no adjacent traffic — rear corner radar misaimed after body repair
  • ADAS warning lamp illuminated — module detected internal aim fault or missing calibration

Always retrieve diagnostic trouble codes (DTCs) from all ADAS-related modules before beginning physical inspection. A stored calibration-missing code confirms the need for recalibration rather than component replacement.

Steering Angle Sensor and Wheel Speed Interaction

The steering angle sensor (SAS) tells the ADAS and stability control modules the driver's intended path. If the SAS zero point is incorrect after an alignment or steering component service, lane keep assist may steer in the wrong direction. Most vehicles require a SAS calibration routine after alignment—this is a separate step from ADAS camera/radar calibration but equally critical.

Wheel speed sensors provide individual wheel velocity data. If one sensor reads differently from the others (due to a damaged tone ring or air gap issue), traction control and adaptive cruise may disengage because the system cannot trust the speed data. Verify wheel speed sensor signals with a scan tool data stream before attempting ADAS calibration.

Safety: Airbags and High-Voltage Systems

ADAS sensors are often located near supplemental restraint system (SRS) components. The forward camera sits behind the windshield near the passenger airbag deployment zone. Rear radar sensors may be near side curtain airbag inflators in the roof pillars.

Before working near ADAS modules:

Disconnect the negative battery terminal and wait the manufacturer-specified SRS capacitor discharge time (typically 1 to 10 minutes)

  • Do not apply power to the vehicle with ADAS modules disconnected unless directed by service information
  • Handle airbag-class connectors with care—do not probe SRS circuits with a test light

On hybrid electric vehicles (HEVs) and battery electric vehicles (BEVs), ADAS radar and camera modules may share mounting areas with high-voltage components. Follow the high-voltage disable procedure: remove the service disconnect, verify zero voltage at the component with a rated voltmeter, and wear Class 0 insulating gloves (1,000 V AC rated) that have been air-tested before use. Never assume a vehicle is de-energized without measurement.

Document all calibration results in the repair order. Many insurers and collision networks require proof of ADAS calibration after windshield or structural repairs.