Study guide
Vehicle Communication Networks & Multiplexing
Red Seal Automotive Service Technician Interprovincial Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the Red Seal Automotive Service Technician Exam
2 Safety & Common Occupational Skills
Shop Safety, Hoists & Personal Protective Equipment Hazardous Materials, WHMIS 2015 & Environmental Disposal Precision Measurement, Tools & Fasteners Communication, Mentoring & Service Documentation
3 Engines, Fuel & Emission Systems (Part A)
Section 3.1: Four-Stroke Engine Fundamentals & Mechanical Diagnostics Accessory Drive Systems: Belts, Tensioners & Pulleys Section 3.2: Fuel Delivery Systems: Gasoline Direct Injection (GDI) & Common-Rail Diesel (CRD) Section 3.3: Ignition Systems, Firing Orders & Combustion Diagnostics
4 Engines, Fuel & Emission Systems (Part B)
Cooling & Lubrication Systems Emission Control Systems: EVAP, EGR, Catalytic Converters & Diesel Controls Diesel Intake, Exhaust & Turbocharger Systems
5 Electrical & Electronic Systems (Part A)
Electrical Fundamentals, Ohm's Law & Circuit Calculations Battery Diagnostics & Starting/Charging System Testing Circuit Troubleshooting: Voltage Drop & Parasitic Draw Testing Circuit & Wiring Repair: Splices, Terminals & Harness Integrity
6 Electrical & Electronic Systems (Part B)
Electronic Components: Sensors, Actuators & Pulse-Width Modulation Vehicle Communication Networks & Multiplexing Programming, Immobilizers & Advanced Module Integration Lighting & Wiper Systems Diagnosis and Repair ADAS Components: Sensors, Diagnosis & Calibration
7 Drivetrain & Transmissions (Part A)
5.1 Clutch Systems & Manual Transmissions/Transaxles 5.2 Automatic Transmissions: Torque Converters & Planetary Gearsets 5.3 Continuously Variable Transmissions (CVT) & Hybrid Drivetrains
8 Drivetrain & Transmissions (Part B)
Section 5.4: Transfer Cases, 4WD/AWD Systems & Drive Axles Section 5.5: Differentials, Final Drives & Gear Setup
9 Brakes, Steering & Suspension (Part A)
Hydraulic Brake Systems & Master Cylinder/Caliper Service Anti-Lock Brakes (ABS), Traction/Stability Control & Wheel Speed Sensors Steering Systems & Electric Power Steering (EPS)
10 Brakes, Steering & Suspension (Part B)
Section 6.4: Suspension Systems & Component Diagnosis Section 6.5: Wheel Alignment Geometry & Correction Section 6.6: Tires, Wheels & Tire Pressure Monitoring Systems (TPMS)
11 HVAC, Restraints & Body Systems
7.1 A/C Refrigeration Cycle, R-1234yf & Refrigerant Service 7.2 Cabin Heating & Automatic Climate Control 7.3 Restraint Systems (SRS) & Body Electrical Accessories Body NVH: Wind Noise, Rattles & Water Leak Diagnosis Latches, Locks, Movable Glass & Body Trim
12 Hybrid & Electric Vehicle Systems
Hybrid & Electric Vehicle High-Voltage Systems High-Voltage Battery Diagnosis & Service
13 Diagnostics & Troubleshooting Strategy
Systematic Diagnostic Strategy & OBD-II Interface Oscilloscope Waveform Analysis & Intermittent Fault Diagnostics
Vehicle Communication Networks & Multiplexing
Key Takeaways Explain This Topic AI
High-speed CAN (CAN-C) runs at 500 kbps using differential voltage signaling on a twisted-pair bus to resist electromagnetic interference.
During a recessive (logical 1) state, CAN-H and CAN-L sit at 2.5V; during a dominant (logical 0) state, CAN-H rises to 3.5V and CAN-L drops to 1.5V.
A healthy high-speed CAN bus has two 120-ohm termination resistors in parallel, yielding a total resistance of 60 ohms across DLC pins 6 and 14.
LIN is a low-cost, single-wire master-slave bus operating at up to 20 kbps for non-safety-critical systems like windows and wipers.
MOST is a high-speed fiber-optic network running in a ring topology for infotainment, where sharp bends or scratches will interrupt light transmission.
Last updated: July 2026
Section 4.5: Vehicle Communication Networks & Multiplexing
Modern vehicles contain dozens of electronic control modules that must share real-time data to coordinate vehicle operation. To eliminate the weight, complexity, and cost of routing dedicated point-to-point wires between every module, automotive manufacturers utilize multiplexing . Multiplexing is the process of transmitting multiple digital messages or data streams simultaneously over a single, shared communication medium (a bus network). This network architecture allows modules, such as the engine control module and transmission control module, to share sensor data like throttle position and engine speed instantly.
Network Topologies and Architectures
Automotive communication networks are arranged in specific physical layouts, known as topologies:
Ring Topology : Modules are connected in a closed loop, where data passes sequentially from one module to the next. A failure in one module or wire breaks the entire loop. This is primarily used in fiber-optic infotainment systems.
Star Topology : All modules connect to a central splice pack or gateway module. If one module or its wire fails, the rest of the network remains operational. However, a failure of the central gateway disables the entire network.
Bus Topology : A single main trunk line running through the vehicle, with individual modules connected via short branch lines (stub wires). This is the standard layout for powertrain and chassis networks.
Controller Area Network (CAN)
The Controller Area Network (CAN) is the dominant multiplexed communication standard in modern light-duty vehicles. Developed by Bosch and standardized globally, high-speed CAN (CAN-C) operates at a transmission speed of 500 kilobits per second (kbps), while low-speed CAN (CAN-B) operates at 125 kbps.
1. Physical Layer and Differential Voltage Signaling
High-speed CAN uses a two-wire bus consisting of a CAN High (CAN-H) and a CAN Low (CAN-L) wire. These wires are twisted together (twisted-pair) to cancel out electromagnetic interference (EMI) and radio frequency interference (RFI).
CAN uses differential voltage signaling, meaning the network logical states (zeros and ones) are determined by the difference in voltage between CAN-H and CAN-L, rather than a single wire's voltage relative to ground. This design makes the network highly resistant to electrical noise:
Recessive State (Logical 1) : When no module is transmitting a dominant bit, the bus rests in the recessive state. Both CAN-H and CAN-L are biased to approximately 2.5 volts. The differential voltage (CAN-H minus CAN-L) is 0 volts.
Dominant State (Logical 0) : When a module transmits a bit, it drives the bus to the dominant state. CAN-H is pulled up to approximately 3.5 volts, and CAN-L is pulled down to approximately 1.5 volts. The differential voltage is 2.0 volts.
Because the receiver circuits only measure the difference between the two wires, any external noise spike that affects both wires equally will not alter the differential voltage, preventing data corruption.
2. Termination Resistors
To prevent electrical signal reflections (echoes) from bouncing back from the ends of the bus wires and corrupting data, high-speed CAN networks require termination resistors . The network uses two 120-ohm resistors connected in parallel across the CAN-H and CAN-L lines at the physical extremities of the bus (typically inside the Engine Control Module - ECM and the Instrument Cluster or Body Control Module - BCM).
By applying Ohm's law for parallel resistance:
Total Resistance = 1 / ((1 / 120) + (1 / 120)) = 60 ohms
Technicians can verify network integrity by connecting a digital multimeter (DMM) across Data Link Connector (DLC) Pin 6 (CAN-H) and Pin 14 (CAN-L). With the battery disconnected:
A reading of 60 ohms indicates both termination resistors and the bus wiring are intact.
A reading of 120 ohms indicates one of the termination resistors or its associated branch circuit is open.
A reading of near 0 ohms indicates a short circuit between the CAN-H and CAN-L wires.
An infinite resistance reading indicates an open circuit in both terminating paths or a complete break in the bus trunk lines.
Local Interconnect Network (LIN)
The Local Interconnect Network (LIN) is a low-speed, single-wire sub-network designed to reduce cost in non-critical applications. LIN operates at speeds up to 20 kbps. It uses a master-slave configuration, where a single master module (such as the BCM) controls all communication on the LIN bus. The slave modules (such as window switches, power mirrors, wiper motors, or climate controls) only transmit data when specifically commanded by the master. LIN does not require termination resistors and is highly cost-effective because it uses a single unshielded wire. The master module acts as a gateway module , translating LIN commands to CAN messages so they can be read by other high-speed modules.
Specialty Networks
Media Oriented Systems Transport (MOST): A high-speed network that uses fiber-optic cables to transmit audio, video, and infotainment data in a ring topology at speeds up to 150 Mbps. Instead of electrical current, MOST transmits pulses of light. If a fiber-optic cable is bent too sharply, kinked, or scratched, light transmission fails, and the entire infotainment loop goes down.
FlexRay : An ultra-high-speed, time-triggered, redundant protocol (up to 10 Mbps) used for safety-critical drive-by-wire applications, active suspension, and advanced driver assistance systems (ADAS) where immediate, deterministic timing is required.
Diagnostic Procedures for Communication Networks
When a network fault occurs, modules cannot exchange data, generating a diagnostic trouble code (DTC) starting with the letter "U" (U-codes), such as U0100 (Lost Communication with ECM). Network diagnosis must follow a structured path:
Verify Battery Voltage : Low system voltage is the leading cause of communication faults. If system voltage drops below 10.5V, modules may randomly shut down or fail to boot.
Perform a Network Scan : Connect a scan tool to the DLC and execute a global module scan to determine which modules are communicating and which are offline.
Measure Resistance at DLC : Disconnect the vehicle battery. Set a DMM to ohms and measure between Pin 6 (CAN-H) and Pin 14 (CAN-L). A reading of 60 ohms is normal. If it is 120 ohms, locate the open circuit or the module containing the missing termination resistor.
Measure Bias Voltages : Reconnect the battery, turn the ignition key ON (engine off). Measure voltage from DLC Pin 6 to Pin 5 (Signal Ground). It should read approximately 2.5V to 2.7V. Measure DLC Pin 14 to Pin 5. It should read approximately 2.3V to 2.5V. The sum of the two voltages should be exactly 5.0V. If CAN-H reads 0V, there is a short to ground. If it reads 12V, there is a short to power.
Use a Digital Storage Oscilloscope (DSO) : Connect channel 1 to CAN-H and channel 2 to CAN-L. Set the time base to 10–20 microseconds. You should see mirrored waveforms. Any spikes, noise, or flatlines indicate physical wiring damage, electromagnetic interference, or a failing transceiver inside a module.
Isolate Modules : If the bus is shorted, disconnect modules one by one while monitoring DLC resistance or the oscilloscope waveform. When the short disappears, the disconnected module is the source of the fault.