Study guide

3.2 Cylinder Blocks, Liners, Pistons, Crankshafts & Valve Trains

Red Seal Heavy Duty Equipment Technician Interprovincial Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety, Regulations & Environmental Compliance

1.1 Workplace Safety, PPE, Lockout/Tagout & Zero-Energy State 1.2 WHMIS 2015/GHS, Hazardous Materials & Environmental Regulations 1.3 Fire Prevention, Emergency Preparedness & Stored-Energy Hazards

2 Chapter 2: Trade Tools, Fasteners, Rigging & Shop Practices

2.1 Precision Measuring Tools & Diagnostic Instruments 2.2 Fasteners, Thread Pitch, Grades & Torque-to-Yield Procedures 2.3 Rigging Hardware, Slings, Crane Hand Signals & Hoisting Safety 2.4 Welding, Cutting, Heating & Electronic Shielding / ECM Grounding

3 Chapter 3: Diesel Engine Fundamentals & Mechanical Systems

3.1 Four-Stroke Diesel Theory, Combustion Principles & Cylinder Heads 3.2 Cylinder Blocks, Liners, Pistons, Crankshafts & Valve Trains 3.3 Engine Lubrication Systems, Oil Pumps, Coolers & Filtration 3.4 Cooling Systems, Water Pumps, Thermostats, Radiators & Fan Drives

4 Chapter 4: Air Induction, Exhaust & Turbocharging Systems

4.1 Air Intake Systems, Dry/Oil-Bath Filters & Restriction Indicators 4.2 Turbochargers, Wastegates & Variable Geometry Turbines (VGT) 4.3 Charge Air Coolers, Intake Heaters & Exhaust Manifolds

5 Chapter 5: Fuel Injection & Engine Management Systems

5.1 High-Pressure Common Rail (HPCR) Systems & Piezo/Solenoid Injectors 5.2 Electronic Unit Injectors (EUI), HEUI & Low-Pressure Supply Circuits 5.3 Diesel Engine Sensors, Actuators, Timing & ECM Calibration 5.4 Diesel Fuel Standards, Winter Blends, Biodiesel & Water Contamination

6 Chapter 6: Exhaust Aftertreatment & Emission Control Systems

6.1 Exhaust Gas Recirculation (EGR) Circuits, Valves & Cooler Failure Modes 6.2 Diesel Oxidation Catalysts (DOC), Diesel Particulate Filters (DPF) & Regeneration 6.3 Selective Catalytic Reduction (SCR), Diesel Exhaust Fluid (DEF) & Anti-Tampering Rules

7 Chapter 7: Hydraulic Principles, Fluids, Reservoirs & Actuators

7.1 Principles of Hydraulics, Pascal's Law, Force, Pressure & Flow 7.2 Hydraulic Fluids, Additives, ISO 4406 Cleanliness & Filtration 7.3 Reservoirs, Hydraulic Hoses, Hard Lines & Fitting Types (ORFS, JIC, BSPP) 7.4 Hydraulic Cylinders, Rotary Motors & Mechanical Leverage Calculations

8 Chapter 8: Hydraulic Pumps, Valves & Control Circuits

8.1 Hydraulic Pumps: Gear, Vane, Radial & Axial Piston (Fixed vs Variable) 8.2 Pressure Control, Directional Spool & Flow Control Valves 8.3 Open-Center, Closed-Center & Load-Sensing Pressure-Compensated (LSPC) Systems 8.4 Pilot Control Systems, Proportional Solenoids & Electro-Hydraulic Controls

9 Chapter 9: Hydrostatic Drive Systems & Industrial Pneumatics

9.1 Closed-Loop Hydrostatic Drive Theory, Swashplates & Bi-Directional Flow 9.2 Charge Pressure Pumps, Cross-Port Relief Valves & Loop Flushing Valves 9.3 Pneumatic Supply Systems, Compressors, Governors & Air Dryers 9.4 Pneumatic Control Valves, Actuators & Heavy Machine Air Circuits

10 Chapter 10: Heavy Duty Electrical Fundamentals & Circuit Diagnostics

10.1 Electrical Fundamentals, Ohm's Law, Watts & Digital Multimeter Usage 10.2 Series, Parallel, Series-Parallel Circuits & Voltage Drop Troubleshooting 10.3 Wiring Harnesses, Connectors, Relays, Solenoids & Circuit Protection 10.4 Heavy Duty 12V/24V Battery Banks, State-of-Charge, Testing & Safe Boosting

11 Chapter 11: Cranking, Charging & Cold-Starting Systems

11.1 Heavy Duty Starting Motors, Control Relays, Solenoids & Pinion Engagement 11.2 Brushless/Brush Alternators, Internal Regulators & Charging Circuit Testing 11.3 Cold-Weather Starting Aids: Glow Plugs, Air Intake Grid Heaters & Block Heaters

12 Chapter 12: Machine Electronics, CAN Bus & Digital Diagnostics

12.1 Electronic Control Modules (ECMs), Microprocessors & Clean Ground Requirements 12.2 Sensors: Analog Variable, Digital Pulse, PWM, Thermistors & Hall-Effect 12.3 Controller Area Network (CAN Bus), SAE J1939 Architecture & Terminating Resistors (60Ω/120Ω) 12.4 Diagnostic Trouble Codes: Suspect Parameter Numbers (SPN), FMI Codes & Guided Troubleshooting

13 Chapter 13: Clutches, Torque Converters & Manual Transmissions

13.1 Heavy Duty Push/Pull Clutches, Free Play, Linkage Adjustment & Clutch Brakes 13.2 Torque Converters: Impeller, Turbine, Stator One-Way Clutch & Fluid Flow 13.3 Lockup Clutches, Fluid Couplers & Hydraulic Driveline Retarders 13.4 Sliding Gear, Collar-Shift, Synchromesh Transmissions & Transfer Cases

14 Chapter 14: Powershift Transmissions, Automatics & Drivelines

14.1 Countershaft & Planetary Powershift Transmissions, Hydraulic Clutch Packs & Modulating Valves 14.2 Electronic Transmission Controls, Shift Calibration & Stall Testing Safety 14.3 Drive Shafts, Universal Joints (Phasing & Angles), Slip Splines & Carrier Bearings 14.4 Standard Differentials, Limited Slip, Inter-Axle Differentials (Power Divider) & Diff Locks

15 Chapter 15: Heavy Duty Drive Axles & Final Drive Systems

15.1 Single, Double & Triple Planetary Final Drives & Gear Reduction Ratios 15.2 Full-Floating Axle Shafts, Spindle Bearings, Preload Adjustments & Hub Seals 15.3 Track Machine Final Drives, Bull Gear Reductions & Duo-Cone (Floating Face) Seals

16 Chapter 16: Heavy Duty Brake Systems & Retarders

16.1 Air Brake Systems: Dual Circuits, Compressors, Valves, S-Cam & Air Disc Brakes 16.2 Hydraulic Service Brakes, Nitrogen-Charged Accumulators, Boosters & Anti-Lock (ABS) 16.3 Spring-Applied Hydraulic-Release (SAHR) & Enclosed Wet Multi-Disc Brakes 16.4 Engine Compression Brakes (Jake Brakes), Exhaust Restrictors & Hydrodynamic Retarders

17 Chapter 17: Steering & Suspension Systems

17.1 Conventional Wheel Steering: Ackerman Geometry, Kingpins, Tie Rods & Power Steering 17.2 Articulated Steering: Center-Pivot Joints, Steering Cylinders & Cushion Valves 17.3 Heavy Duty Suspensions: Walking Beams, Rubber Blocks, Air Springs & Hydraulic Struts

18 Chapter 18: Undercarriage & Wheel Assemblies

18.1 Track Chains, Rails, Sealed and Lubricated Tracks (SALT), Pins, Bushings & Pitch Measurement 18.2 Track Rollers, Front Idlers, Recoil Springs & Grease-Tension Adjustment 18.3 Off-The-Road (OTR) Tires, Multi-Piece Rims, Demounting Safety & Wheel Torquing

19 Chapter 19: Environmental Control & Sound Suppression Systems

19.1 Air Conditioning Refrigeration Cycle, Compressors, Condensers, TXVs & R-134a/R-1234yf Handling 19.2 Cab Heating Cores, Coolant Shutoff Valves, Auxiliary Fuel-Fired Heaters & Defrosting 19.3 Cab Filtration (HEPA/Activated Carbon), Positive Pressurization & Acoustic Sound Suppression

20 Chapter 20: Structural Components, Cabs, Implements & Diagnostics

20.1 Equipment Chassis, Articulation Bearings, Structural Welds & Non-Destructive Testing (NDT) 20.2 Roll-Over Protective Structures (ROPS), Falling Object Structures (FOPS) & Cab Certification 20.3 Work Implements (Buckets, Blades, Rippers), Pivot Pins, Bushings & Hydraulic Quick Couplers 20.4 Systematic 8-Step Troubleshooting, ISO 4406 Fluid Cleanliness, Wear Metal Spectrometry & Preventive Maintenance

21 Official Blueprint & Professional Practice

21.1 Official Exam Blueprint, Format & Study Strategy 21.2 Service Information, Documentation & Job Action Plans 21.3 Communication, Mentoring & Shift Handover

22 Operator Station, Hybrid & All-Electric Equipment

22.1 Operator Station Components, Visibility, Controls & Monitoring 22.2 Hybrid Equipment: Architecture, Service & Diagnostics 22.3 All-Electric Equipment: Batteries, Charging, Drives & Diagnostics

3.2 Cylinder Blocks, Liners, Pistons, Crankshafts & Valve Trains

Key Takeaways Explain This Topic AI

Wet cylinder liner protrusion (typically 0.003 in to 0.006 in / 0.076 mm to 0.152 mm) must be verified with hold-down clamps and dial indicators, with shims installed beneath the counterbore to correct uneven standout.

Liner cavitation erosion is caused by high-frequency piston slap inducing microscopic coolant vapor bubble implosions against the outer liner wall; it is prevented through rigid liner fit, proper protrusion, and chemical passivating coolants.

Fractured-split connecting rods feature unique microscopic interlocking mating surfaces that must never be filed, deburred, wire-brushed, or swapped.

Crankshaft journals must be inspected with outside micrometers for out-of-round and taper, maintaining oil clearances within 0.002 in to 0.004 in (0.051 mm to 0.102 mm) verified by Plastigauge or dial bore gauge.

Keystone piston rings provide self-cleaning action in high-temperature ring grooves, and end gaps must be measured at specified bore depths and staggered to prevent combustion blow-by.

Last updated: September 2026

3.2 Cylinder Blocks, Liners, Pistons, Crankshafts & Valve Trains

The bottom end and valve train of a heavy-duty diesel engine endure intense mechanical stress, cyclic torsional vibrations, and severe thermal loading. Precision measurements, meticulous adherence to tolerances, and accurate failure diagnostics are fundamental to ensuring engine longevity and reliability.

Cylinder Blocks & Liners (Parent Bore, Dry & Wet Liners)

Heavy-duty engine blocks are cast from high-strength grey iron or compacted graphite iron, featuring deep-skirt crankcase architectures extending well below the crankshaft centerline, often reinforced with cross-bolted main bearing caps. Parent Bore Dry Cylinder Liner Wet Cylinder Liner

  • (Integral Block) (Thin Sleeve Pressed in) (Coolant Directly Contacts Outer Wall)
  • ┌──────────────┐ ┌──┬──────────────┬──┐ ┌──┬──────────────┬──┐ ◄ Upper Flange
  • │ Block Iron │ │B │ Liner │B │ │ │ Liner │ │
  • │ │ │l │ │l │ │C │ │C │
  • │ Cylinder │ │o │ Cylinder │o │ │o │ Cylinder │o │ ◄ Coolant
  • │ Bore │ │c │ Bore │c │ │o │ Bore │o │ Passage
  • │ │ │k │ │k │ │l │ │l │
  • │ │ │ │ │ │ │ │ │ │
  • └──────────────┘ └──┴──────────────┴──┘ └──┴──────────────┴──┘ ◄ Lower O-Ring Seals
  • Liner Architectural Differences

Parent Bore (En-bloc): Cylinder bores are machined directly into the engine block casting. When worn, cylinders must be bored and honed oversize, requiring oversize pistons and rings.

Dry Liners: Thin-walled steel or cast iron sleeves pressed into a fully supported cylinder bore. The liner does not contact coolant directly. They provide cylinder renewal without overboring the block, but heat dissipation depends on 100% metal-to-metal contact with the block bore.

Wet Liners: Heavy-duty engines (Caterpillar, Cummins, Detroit, John Deere) almost universally utilize wet liners. The outer wall of the liner is exposed directly to circulating engine coolant. It is supported at the top by a machined counterbore ledge and sealed at the bottom crankcase bore by multiple elastomeric O-rings (typically fluorocarbon/Viton and ethylene-propylene) and a crevice seal.

Wet Liner Protrusion (Standout) Measurement & Shimming

Liner protrusion—the height the liner flange extends above the cylinder block fire deck—is the single most critical dimension in wet-liner engine assembly. Dial Indicator on Sled Gauge

  • [ 0.004" ]
  • ▼
  • Block Deck ───┐ ┌─── Liner Flange Fire Dam
  • ══════════════╡ │═════════════════════════
  • Block Deck │ │
  • Counterbore ──┴───┘ ◄ Counterbore Shim Placed Here
  • Precision Protrusion Measurement Procedure

Thoroughly clean the block counterbore ledge using a brass wire wheel or chemical solvent to remove all carbon, rust, and old sealant. Never use aggressive abrasives that cut into the iron.

Install the clean liner into the bore without lower O-ring seals.

Secure the liner down into the counterbore using hold-down clamps and Grade 8 bolts torqued to specified clamping loads (typically 50 to 70 lb-ft / 68 to 95 N·m) to simulate the clamped load of a torqued cylinder head.

Mount a dial indicator on a sled fixture. Zero the indicator under tension on the engine block deck surface.

Slide the indicator contact tip over onto the liner flange fire dam. Measure at four points: 0°, 90°, 180°, and 270° around the circumference.

Standard Specifications: Typical liner protrusion is 0.003 to 0.006 in (0.076 to 0.152 mm) . Crucially, variation across four points on a single liner must not exceed 0.001 in (0.025 mm) , and variation between any two adjacent cylinders must not exceed 0.001 in (0.025 mm) .

Corrective Shimming: If protrusion is below specification or uneven, the counterbore ledge must be cut using a portable counterbore cutting tool to ensure a flat, square seating surface. Precision stainless steel or brass shims of calculated thickness are placed beneath the liner flange to achieve exact protrusion.

Consequences of Incorrect Protrusion

Insufficient Protrusion (<0.003 in): The cylinder head fire deck cannot exert adequate clamping pressure on the gasket fire ring. High-pressure combustion gases blow past the seal, burning the gasket and entering the cooling jacket.

Excessive Protrusion (>0.006 in): The liner takes an excessive proportion of total cylinder head bolt clamping force. This flexes the cylinder head casting, starves outer coolant/oil seal beads of pressure, and causes the liner flange to crack or fracture.

Wet Liner Cavitation Erosion Mechanics

Cavitation erosion is an aggressive failure mode occurring on the coolant side of wet cylinder liners:

Piston Slap Excitation: During the transition between the compression and power strokes, combustion pressure violently slaps the piston skirt against the major thrust side of the liner wall.

Vibratory Flexing: This impact induces high-frequency acoustic vibrations in the cylinder liner wall, causing it to flex inward and outward at thousands of cycles per second.

Vapor Bubble Formation: As the liner wall rapidly flexes away from the coolant, a localized low-pressure zone forms where coolant pressure drops below its vapor pressure. Microscopic vapor bubbles instantaneously nucleate.

Violent Bubble Implosion: As the liner wall rebounds outward, localized pressure spikes dramatically. The vapor bubbles implode violently against the liner surface, generating micro-jets of liquid with localized shock pressures exceeding 100,000 psi (700 MPa) .

Pinhole Perforation: These shockwaves tear microscopic particles of iron from the outer liner surface. Over operating hours, deep honeycomb pitting develops exclusively along the major and minor thrust axes, eventually perforating the liner wall and dumping coolant into the combustion chamber and oil pan.

Piston Anatomy, Skirt Profiles & Ring Packs Piston Anatomy & Ring Pack:

  • ┌──────────────────────────────┐ ◄ Forged Steel Crown (Combustion Bowl)
  • │ [ Combustion Bowl ] │
  • │ ──┬──────────────────────┬── │ ◄ Top Compression Ring (Keystone Profile)
  • │ │ │ │
  • │ ──┴──────────────────────┴── │ ◄ Second Scraper Ring (Napier Hook Face)
  • │ ──┬──────────────────────┬── │ ◄ Oil Control Ring (With Expander Spring)
  • │ │ Wrist Pin │ │
  • │ │ (Bushed Boss) │ │
  • │ └──────────────────────┘ │ ◄ Cast Aluminum Skirt (Cam-Ground Oval)
  • └──────────────────────────────┘
  • Piston Construction & Materials

Articulated Pistons: Feature a forged steel crown containing the combustion bowl and ring pack, pinned to a separate cast aluminum skirt. The steel crown withstands peak combustion temperatures and pressures exceeding 200 bar, while the lightweight aluminum skirt stabilizes the piston in the bore.

Monolithic Steel Pistons (e.g., Mahle Monotherm): Single-piece forged steel pistons standard in modern Tier 4 Final engines. Steel's superior tensile strength allows thinner cross-sections, reduced compression height, and larger internal cooling oil galleries.

Cam-Ground Skirt Profile: Pistons are machined elliptical (oval) when cold, with the minor diameter parallel to the wrist pin and the major diameter perpendicular to the wrist pin (thrust faces). Because the wrist pin boss contains far more aluminum mass than the thin skirt walls, it expands significantly more when heated. At operating temperature, the piston expands into a perfectly round cylinder.

Barrel-Taper Profile: The piston crown is subjected to direct combustion flame and operates hotter than the lower skirt. Therefore, the crown diameter is machined noticeably smaller than the skirt diameter cold to allow for greater thermal expansion.

The Three-Ring Pack

Top Compression Ring: Features a keystone (wedge-shaped) cross-section (typically 7° or 15° angled sides) and a plasma-moly or ceramic-chromium Physical Vapor Deposition (PVD) coating. As the piston oscillates, the tapered keystone sides exert a self-cleaning mechanical scraping action in the ring groove, preventing hard carbon from packing behind the ring and causing ring sticking.

Second (Intermediate) Ring: Usually a taper-faced ring with a Napier hook lower edge. Acts as both a secondary combustion pressure seal and a scraper that strips excess lubricating oil downward away from the combustion chamber.

Oil Control Ring: Composed of dual chrome or nitrided steel rails energized by an internal coiled stainless steel expander spring. It meters a microscopic oil film (approx. 1 to 2 μm thick) on the cylinder wall to lubricate the compression rings, scraping the surplus downward through oil drainage holes in the piston ring land back to the crankcase.

Precision Ring Gap & Clearance Measurements

Ring End Gap: Square the ring into the cylinder bore at a specified depth (using an inverted piston head to ensure perpendicularity). Measure the gap between ring ends using a feeler gauge. An end gap that is too small will butt together when thermally expanded, causing severe bore scuffing, ring breakage, and piston seizure.

Side Clearance: Insert a feeler gauge between the ring and the ring land groove. Excessive clearance leads to ring flutter at high RPM and oil pumping into the combustion chamber; insufficient clearance causes ring binding when hot.

Staggering Rule: Stagger all ring end gaps (typically 120° apart for a 3-ring pack, or 180° apart for compression rings). Never align any ring end gap with the wrist pin axis or the major/minor thrust faces.

Connecting Rods & Crankshaft Precision Machining Connecting Rod Anatomy:

  • [ Small End / Pin Bushing ]
  • │
  • │ ◄ H-Beam Shank (High Tensile Alloy Steel)
  • │
  • [ Big End / Crank Journal ]
  • ─────────────────────────── ◄ Fractured-Split Parting Line
  • [ Rod Cap ] (Unique Interlocking Jagged Teeth)
  • Fractured-Split (Crack-Split) Connecting Rods

Modern heavy-duty engines employ cracked-cap connecting rod technology:

Manufacturing: The connecting rod big-end is forged as a single piece. Laser notches are scribed on the parting line, and a hydraulic mandrel snaps the cap away from the rod shank under high impulse force.

Interlocking Strength: The resulting fracture surfaces exhibit thousands of unique, microscopic interlocking jagged teeth. This provides exceptional shear resistance and guarantees precise cap-to-rod alignment without alignment dowel pins.

CRITICAL SHOP RULE: Never deburr, stone, file, wire brush, or clean fractured parting surfaces with abrasive pads. Altering the microscopic fracture peaks destroys the cap-to-rod interlocking alignment, causing bearing bore distortion, oil clearance failure, and catastrophic rod throw. Caps and rods are uniquely matched pairs and cannot be interchanged, reversed, or mixed.

Crankshaft Journal Inspection: Taper & Out-of-Round

Inspect all main and rod journals using a calibrated outside micrometer. Measure each journal across two axes (0° and 90°) at two longitudinal locations (front and rear of the journal). Crankshaft Journal Measurement Points:

  • Position A (Front) Position B (Rear)
  • Vertical Vertical
  • ▲ ▲
  • │ │
  • Horizontal ◄───┼───► Horizontal ◄──────┼──────► Horizontal
  • │ │
  • ▼ ▼
  • Out-of-Round = Vertical minus Horizontal at the SAME position (A or B)
  • Taper = Front measurement minus Rear measurement along the SAME axis

Out-of-Round (Ovality): The difference between the vertical and horizontal diameter at the same longitudinal position. Maximum service limit is typically 0.0005 in (0.013 mm) .

Taper (Conical Wear): The difference between the front diameter and rear diameter along the same plane. Maximum service limit is typically 0.0005 in (0.013 mm) .

Corrective Action: If wear exceeds limits, machine the crankshaft to standard undersizes (e.g., -0.010 in, -0.020 in / -0.25 mm, -0.50 mm) and fit matching undersize bearing shells.

Main Bearing Oil Clearance & Plastigauge Verification

Hydrodynamic oil film clearance must be maintained between 0.0020 and 0.0040 in (0.051 to 0.102 mm) on heavy-duty journals:

Ensure journals, bearing shells, and caps are clean and completely dry of oil.

Lay a calibrated strip of Plastigauge wax across the journal centerline.

Install the bearing cap and torque all bolts to full manufacturer specifications in sequence. Do not rotate the crankshaft while Plastigauge is installed.

Remove the cap. Compare the width of the flattened wax strip against the graduated scale envelope to determine running clearance.

Crankshaft End-Play (Thrust Clearance)

Crankshaft end-play regulates forward and aft movement, controlled by thrust washers or flanged main bearings:

Mount a dial indicator on the flywheel housing with the indicator tip resting against the flywheel face or crankshaft snout.

Pry the crankshaft fully forward, zero the gauge, and pry the crankshaft fully rearward.

Typical service limit is 0.004 to 0.012 in (0.10 to 0.30 mm) . Excessive end-play causes connecting rod twisting, abnormal wrist pin bushing wear, and timing gear misalignment.

Valve Trains: Camshafts, Lifters, Pushrods & Rockers

  • Valve Train Type Pushrod / Cam-in-Block (OHV) Overhead Camshaft (OHC / DOHC)
  • Location Camshaft located low in engine block crankcase Camshaft mounted directly on cylinder head deck

Actuation Cam Lobe ──► Lifter ──► Pushrod ──► Rocker ──► Valve Cam Lobe ──► Roller Rocker (or Direct Follower) ──► Valve

Inertia / Deflection High reciprocating mass; pushrods flex under high valve spring loads Low reciprocating mass; zero pushrod flex; precise high-RPM valve control

Engine Height Compact cylinder head profile; lower overall engine center of gravity Taller cylinder head assembly; requires complex timing gear or chain train

Camshaft Lobe Lift Measurement

Measure total lobe height across the nose (H) and base circle diameter (W) with an outside micrometer:

Lobe Lift = H - W

Compare calculated lift against OEM specifications. Worn or spalled lobes reduce valve lift and duration, causing restricted cylinder breathing, low boost pressure, black smoke, and cylinder misfire under load.

Valve Lash & Engine Brake Adjustment

Thermal Clearance Necessity: Exhaust valves run hundreds of degrees hotter than intake valves; therefore, exhaust lash clearance is always wider (e.g., 0.026 in / 0.66 mm exhaust vs 0.014 in / 0.36 mm intake cold).

Adjustment Method: Turn engine to specified cylinder TDC compression stroke. Insert feeler gauge between rocker arm pad and valve bridge/stem. Adjust screw until a firm sliding drag is felt. Tighten locknut and re-verify clearance.

Compression Brake (Jake Brake) Slave Piston Lash: Adjust slave piston lash using a dial indicator or feeler gauge (typically 0.018 to 0.032 in). If slave piston clearance is set too tight, the exhaust valve will be held cracked off its seat during normal combustion, causing burned valves, severe compression loss, and engine misfire.