Study guide
12.3 Controller Area Network (CAN Bus), SAE J1939 Architecture & Terminating Resistors (60Ω/120Ω)
Red Seal Heavy Duty Equipment Technician Interprovincial Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety, Regulations & Environmental Compliance
1.1 Workplace Safety, PPE, Lockout/Tagout & Zero-Energy State 1.2 WHMIS 2015/GHS, Hazardous Materials & Environmental Regulations 1.3 Fire Prevention, Emergency Preparedness & Stored-Energy Hazards
2 Chapter 2: Trade Tools, Fasteners, Rigging & Shop Practices
2.1 Precision Measuring Tools & Diagnostic Instruments 2.2 Fasteners, Thread Pitch, Grades & Torque-to-Yield Procedures 2.3 Rigging Hardware, Slings, Crane Hand Signals & Hoisting Safety 2.4 Welding, Cutting, Heating & Electronic Shielding / ECM Grounding
3 Chapter 3: Diesel Engine Fundamentals & Mechanical Systems
3.1 Four-Stroke Diesel Theory, Combustion Principles & Cylinder Heads 3.2 Cylinder Blocks, Liners, Pistons, Crankshafts & Valve Trains 3.3 Engine Lubrication Systems, Oil Pumps, Coolers & Filtration 3.4 Cooling Systems, Water Pumps, Thermostats, Radiators & Fan Drives
4 Chapter 4: Air Induction, Exhaust & Turbocharging Systems
4.1 Air Intake Systems, Dry/Oil-Bath Filters & Restriction Indicators 4.2 Turbochargers, Wastegates & Variable Geometry Turbines (VGT) 4.3 Charge Air Coolers, Intake Heaters & Exhaust Manifolds
5 Chapter 5: Fuel Injection & Engine Management Systems
5.1 High-Pressure Common Rail (HPCR) Systems & Piezo/Solenoid Injectors 5.2 Electronic Unit Injectors (EUI), HEUI & Low-Pressure Supply Circuits 5.3 Diesel Engine Sensors, Actuators, Timing & ECM Calibration 5.4 Diesel Fuel Standards, Winter Blends, Biodiesel & Water Contamination
6 Chapter 6: Exhaust Aftertreatment & Emission Control Systems
6.1 Exhaust Gas Recirculation (EGR) Circuits, Valves & Cooler Failure Modes 6.2 Diesel Oxidation Catalysts (DOC), Diesel Particulate Filters (DPF) & Regeneration 6.3 Selective Catalytic Reduction (SCR), Diesel Exhaust Fluid (DEF) & Anti-Tampering Rules
7 Chapter 7: Hydraulic Principles, Fluids, Reservoirs & Actuators
7.1 Principles of Hydraulics, Pascal's Law, Force, Pressure & Flow 7.2 Hydraulic Fluids, Additives, ISO 4406 Cleanliness & Filtration 7.3 Reservoirs, Hydraulic Hoses, Hard Lines & Fitting Types (ORFS, JIC, BSPP) 7.4 Hydraulic Cylinders, Rotary Motors & Mechanical Leverage Calculations
8 Chapter 8: Hydraulic Pumps, Valves & Control Circuits
8.1 Hydraulic Pumps: Gear, Vane, Radial & Axial Piston (Fixed vs Variable) 8.2 Pressure Control, Directional Spool & Flow Control Valves 8.3 Open-Center, Closed-Center & Load-Sensing Pressure-Compensated (LSPC) Systems 8.4 Pilot Control Systems, Proportional Solenoids & Electro-Hydraulic Controls
9 Chapter 9: Hydrostatic Drive Systems & Industrial Pneumatics
9.1 Closed-Loop Hydrostatic Drive Theory, Swashplates & Bi-Directional Flow 9.2 Charge Pressure Pumps, Cross-Port Relief Valves & Loop Flushing Valves 9.3 Pneumatic Supply Systems, Compressors, Governors & Air Dryers 9.4 Pneumatic Control Valves, Actuators & Heavy Machine Air Circuits
10 Chapter 10: Heavy Duty Electrical Fundamentals & Circuit Diagnostics
10.1 Electrical Fundamentals, Ohm's Law, Watts & Digital Multimeter Usage 10.2 Series, Parallel, Series-Parallel Circuits & Voltage Drop Troubleshooting 10.3 Wiring Harnesses, Connectors, Relays, Solenoids & Circuit Protection 10.4 Heavy Duty 12V/24V Battery Banks, State-of-Charge, Testing & Safe Boosting
11 Chapter 11: Cranking, Charging & Cold-Starting Systems
11.1 Heavy Duty Starting Motors, Control Relays, Solenoids & Pinion Engagement 11.2 Brushless/Brush Alternators, Internal Regulators & Charging Circuit Testing 11.3 Cold-Weather Starting Aids: Glow Plugs, Air Intake Grid Heaters & Block Heaters
12 Chapter 12: Machine Electronics, CAN Bus & Digital Diagnostics
12.1 Electronic Control Modules (ECMs), Microprocessors & Clean Ground Requirements 12.2 Sensors: Analog Variable, Digital Pulse, PWM, Thermistors & Hall-Effect 12.3 Controller Area Network (CAN Bus), SAE J1939 Architecture & Terminating Resistors (60Ω/120Ω) 12.4 Diagnostic Trouble Codes: Suspect Parameter Numbers (SPN), FMI Codes & Guided Troubleshooting
13 Chapter 13: Clutches, Torque Converters & Manual Transmissions
13.1 Heavy Duty Push/Pull Clutches, Free Play, Linkage Adjustment & Clutch Brakes 13.2 Torque Converters: Impeller, Turbine, Stator One-Way Clutch & Fluid Flow 13.3 Lockup Clutches, Fluid Couplers & Hydraulic Driveline Retarders 13.4 Sliding Gear, Collar-Shift, Synchromesh Transmissions & Transfer Cases
14 Chapter 14: Powershift Transmissions, Automatics & Drivelines
14.1 Countershaft & Planetary Powershift Transmissions, Hydraulic Clutch Packs & Modulating Valves 14.2 Electronic Transmission Controls, Shift Calibration & Stall Testing Safety 14.3 Drive Shafts, Universal Joints (Phasing & Angles), Slip Splines & Carrier Bearings 14.4 Standard Differentials, Limited Slip, Inter-Axle Differentials (Power Divider) & Diff Locks
15 Chapter 15: Heavy Duty Drive Axles & Final Drive Systems
15.1 Single, Double & Triple Planetary Final Drives & Gear Reduction Ratios 15.2 Full-Floating Axle Shafts, Spindle Bearings, Preload Adjustments & Hub Seals 15.3 Track Machine Final Drives, Bull Gear Reductions & Duo-Cone (Floating Face) Seals
16 Chapter 16: Heavy Duty Brake Systems & Retarders
16.1 Air Brake Systems: Dual Circuits, Compressors, Valves, S-Cam & Air Disc Brakes 16.2 Hydraulic Service Brakes, Nitrogen-Charged Accumulators, Boosters & Anti-Lock (ABS) 16.3 Spring-Applied Hydraulic-Release (SAHR) & Enclosed Wet Multi-Disc Brakes 16.4 Engine Compression Brakes (Jake Brakes), Exhaust Restrictors & Hydrodynamic Retarders
17 Chapter 17: Steering & Suspension Systems
17.1 Conventional Wheel Steering: Ackerman Geometry, Kingpins, Tie Rods & Power Steering 17.2 Articulated Steering: Center-Pivot Joints, Steering Cylinders & Cushion Valves 17.3 Heavy Duty Suspensions: Walking Beams, Rubber Blocks, Air Springs & Hydraulic Struts
18 Chapter 18: Undercarriage & Wheel Assemblies
18.1 Track Chains, Rails, Sealed and Lubricated Tracks (SALT), Pins, Bushings & Pitch Measurement 18.2 Track Rollers, Front Idlers, Recoil Springs & Grease-Tension Adjustment 18.3 Off-The-Road (OTR) Tires, Multi-Piece Rims, Demounting Safety & Wheel Torquing
19 Chapter 19: Environmental Control & Sound Suppression Systems
19.1 Air Conditioning Refrigeration Cycle, Compressors, Condensers, TXVs & R-134a/R-1234yf Handling 19.2 Cab Heating Cores, Coolant Shutoff Valves, Auxiliary Fuel-Fired Heaters & Defrosting 19.3 Cab Filtration (HEPA/Activated Carbon), Positive Pressurization & Acoustic Sound Suppression
20 Chapter 20: Structural Components, Cabs, Implements & Diagnostics
20.1 Equipment Chassis, Articulation Bearings, Structural Welds & Non-Destructive Testing (NDT) 20.2 Roll-Over Protective Structures (ROPS), Falling Object Structures (FOPS) & Cab Certification 20.3 Work Implements (Buckets, Blades, Rippers), Pivot Pins, Bushings & Hydraulic Quick Couplers 20.4 Systematic 8-Step Troubleshooting, ISO 4406 Fluid Cleanliness, Wear Metal Spectrometry & Preventive Maintenance
21 Official Blueprint & Professional Practice
21.1 Official Exam Blueprint, Format & Study Strategy 21.2 Service Information, Documentation & Job Action Plans 21.3 Communication, Mentoring & Shift Handover
22 Operator Station, Hybrid & All-Electric Equipment
22.1 Operator Station Components, Visibility, Controls & Monitoring 22.2 Hybrid Equipment: Architecture, Service & Diagnostics 22.3 All-Electric Equipment: Batteries, Charging, Drives & Diagnostics
12.3 Controller Area Network (CAN Bus), SAE J1939 Architecture & Terminating Resistors (60Ω/120Ω)
Key Takeaways Explain This Topic AI
SAE J1939 is a high-speed differential broadcast serial bus operating at 250 kbps (J1939-11) or 500 kbps (J1939-14), utilizing twisted-pair wiring (CAN_H yellow, CAN_L green) to cancel electromagnetic interference.
The physical bus layout consists of a linear backbone trunk line with stub connections limited to a maximum length of 1.0 meter (3.3 feet) to prevent destructive signal reflections.
Two 120-ohm terminating resistors placed at the extreme physical ends of the backbone in parallel establish exactly 60 ohms total bus resistance; measuring 120 ohms indicates an open/missing terminator, while 40 ohms indicates an unauthorized third terminator.
At the recessive state (bus idle/logical 1), both CAN_H and CAN_L sit at 2.5V with 0V differential; during a dominant state (logical 0), CAN_H rises to ~3.5V and CAN_L drops to ~1.5V, creating a 2.0V differential.
Arbitration is non-destructive and bitwise based on the 29-bit CAN identifier, where dominant zero bits override recessive one bits, ensuring the highest priority safety and powertrain messages transmit without delay.
Last updated: September 2026
Controller Area Network (CAN Bus), SAE J1939 Architecture & Terminating Resistors (60Ω/120Ω)
Prior to the advent of serial multiplexing, heavy-duty mobile machinery required massive, complex wiring harnesses containing hundreds of individual copper conductors running between the operator cab, engine compartment, transmission, and hydraulic control valves. Each sensor signal had to be hardwired independently to every controller that required the information. The Controller Area Network (CAN) —specifically standardized for heavy commercial vehicles and off-highway equipment under the Society of Automotive Engineers (SAE) J1939 family of standards—revolutionized machine design by replacing point-to-point wiring with a shared, high-speed digital communications bus. A Red Seal technician must master J1939 physical layer architecture, differential voltage signaling, termination mathematics, and systematic bus troubleshooting.
SAE J1939 Fundamentals & Physical Layer Specifications
SAE J1939 is an open industrial communications standard built upon the Robert Bosch CAN 2.0B protocol. It defines the physical wiring, baud rates, message framing, network management, and diagnostic protocols for commercial vehicles, mining equipment, agricultural tractors, and construction machinery. SAE J1939 LINEAR BUS TOPOLOGY
- Terminating Terminating
- Resistor Resistor
- (120 Ω) (120 Ω)
- ┌──────┐ ┌──────┐
- │ ├──────┬──────────────────────┬──────────────────────┬──────┤ │
- │120 Ω │ │ CAN_High (Yellow) │ │ │120 Ω │
- │ ├────┐ │ │ │ ┌────┤ │
- └──────┘ │ │ CAN_Low (Green) │ │ │ └──────┘
- │ │ │ │ │
- │ │ │ │ │
- │ │ Stub Drop (≤ 1.0 m) │ │ │ Stub Drop (≤ 1.0 m)
- ▼ ▼ ▼ ▼ ▼
- ┌───────────┐ ┌───────────┐ ┌───────────┐
- │Engine ECM │ │ Trans ECM │ │Hydraul ECM│
- └───────────┘ └───────────┘ └───────────┘
- Data Transmission Rates
SAE J1939-11 & J1939-15: Standard heavy-duty data rate of 250 kbps (kilobits per second) . Each bit duration ( T bit T_{\text{bit}} T bit ) is exactly 4.0 μ s 4.0\ \mu\text{s} 4.0 μ s . J1939-11 specifies shielded twisted pair, while J1939-15 permits unshielded twisted pair in light-duty or enclosed runs.
SAE J1939-14: High-speed physical layer operating at 500 kbps ( T bit = 2.0 μ s T_{\text{bit}} = 2.0\ \mu\text{s} T bit = 2.0 μ s ). Deployed on modern Tier 4 Final and Stage V machinery to support high-bandwidth requirements for complex exhaust aftertreatment dosing systems, automated machine guidance (GPS/telematics), and electronic implement steering.
Physical Media: Twisted Shielded Pair (J1939-11)
Under the J1939-11 physical specification, the cable assembly consists of three elements encased within an outer protective jacket:
CAN_High (CAN_H): Yellow insulated copper conductor.
CAN_Low (CAN_L): Green insulated copper conductor.
CAN_Shield (Drain Wire): Bare tinned copper drain wire in continuous contact with a conductive aluminum-mylar foil wrap surrounding the twisted conductors.
The Critical Shield Grounding Rule: The CAN shield drain wire must be connected to machine chassis ground at ONLY ONE SINGLE POINT along the entire bus (typically near the primary power distribution center or central diagnostic connector). Grounding the shield at multiple points creates an electrical ground loop : circulating currents from high-draw chassis loads flow through the shield, inducing destructive electromagnetic noise directly into the yellow and green data lines!
Twisted-Pair Common-Mode Rejection
The CAN_H and CAN_L wires are twisted around each other at a mandatory pitch of at least 1 twist per inch (approximately 33 to 40 twists per meter) . This geometry provides exceptional Common-Mode Noise Rejection :
When an external electromagnetic interference field (from an alternator stator, a high-current starter relay, or a radio transmitter) passes through the cable, it cuts across both conductors equally because their physical positions alternate continuously. Consequently, the noise induces an identical unwanted voltage spike on both CAN_H and CAN_L simultaneously ( V noise V_{\text{noise}} V noise ).
Because the receiving CAN transceiver does not measure voltage relative to ground, but strictly measures the differential voltage between the two conductors: V diff = ( V CAN_H + V noise ) − ( V CAN_L + V noise ) = V CAN_H − V CAN_L V_{\text{diff}} = (V_{\text{CAN\_H}} + V_{\text{noise}}) - (V_{\text{CAN\_L}} + V_{\text{noise}}) = V_{\text{CAN\_H}} - V_{\text{CAN\_L}} V diff = ( V CAN_H + V noise ) − ( V CAN_L + V noise ) = V CAN_H − V CAN_L
The common-mode noise voltage ( V noise V_{\text{noise}} V noise ) cancels out completely, leaving the true digital data packet unaltered.
Bus Topology: Linear Backbone vs. Stub Drops
SAE J1939 strictly dictates a linear bus topology (a single continuous trunk line). Star, ring, or tree topologies are explicitly prohibited.
1. Backbone Trunk Line
The main bus cable—termed the backbone —must form an unbroken continuous electrical trunk line running from one physical end of the machinery to the other (e.g., from the front cab instrument cluster down the chassis frame to the engine and aftertreatment compartments). Under J1939-11, the maximum total backbone length must not exceed 40 meters (131 feet) .
2. Stub Drops
Individual electronic controllers, sensors, and the 9-pin Deutsch diagnostic connector branch off the main backbone via short branch lines known as stub drops :
Maximum Stub Length: Must not exceed 1.0 meter (3.3 feet) under J1939-11. For 500 kbps J1939-14 networks, OEM specifications recommend stubs under 0.33 meters (1.0 foot) .
The Physics of Stub Length Limits: Electrical signals travel through copper wire at approximately 200 , 000 km/s 200,000\text{ km/s} 200 , 000 km/s (two-thirds the speed of light). If a stub drop is too long, high-frequency signal transitions reflect off the high-impedance transceiver input at the end of the stub and travel back into the main backbone. These reflections produce waveform "ringing" (voltage overshoot and undershoot) that corrupts data bits, causing cyclic redundancy check (CRC) errors and forcing controllers into bus-off communication shutdown.
Terminating Resistors: Theory, Mathematics & Testing
High-speed transmission lines require precise impedance matching to prevent signal reflections. When a high-frequency digital pulse reaches the end of an unterminated wire, the sudden impedance discontinuity causes the electromagnetic wave energy to bounce backward toward the transmitter, obliterating following bits. PARALLEL TERMINATING RESISTOR NETWORK
- ┌───────────────────────────────┐
- ┌──────────┤ CAN_High Backbone (Yellow) ├──────────┐
- │ └───────────────────────────────┘ │
- ┌───┴───┐ ┌───┴───┐
- │ R_T1 │ 120 Ω │ R_T2 │ 120 Ω
- │ (End) │ (0.5W, 1%) │ (End) │ (0.5W, 1%)
- └───┬───┘ └───┬───┘
- │ ┌───────────────────────────────┐ │
- └──────────┤ CAN_Low Backbone (Green) ├──────────┘
- └───────────────────────────────┘
- R_Total = (120 x 120) / (120 + 120) = 14400 / 240 = 60.0 Ω
- The 120-Ohm Standard & Parallel Equivalent Resistance
To absorb the signal wave energy completely without reflection, a 120 Ω 120\ \Omega 120 Ω (0.5 W, 1% tolerance, metal film) terminating resistor is installed across CAN_H and CAN_L at the two extreme physical ends of the backbone trunk line. These resistors match the characteristic impedance ( Z 0 ≈ 120 Ω Z_0 \approx 120\ \Omega Z 0 ≈ 120 Ω ) of the twisted cable.
Because the two 120 Ω 120\ \Omega 120 Ω terminating resistors are connected across the same two conductors, they are wired in an electrical parallel circuit . The equivalent total bus resistance ( R total R_{\text{total}} R total ) is calculated using the standard parallel resistance formula: 1 R total = 1 R 1 + 1 R 2 = 1 120 Ω + 1 120 Ω = 2 120 Ω ⟹ R total = 120 Ω 2 = 60.0 Ω \frac{1}{R_{\text{total}}} = \frac{1}{R_1} + \frac{1}{R_2} = \frac{1}{120\ \Omega} + \frac{1}{120\ \Omega} = \frac{2}{120\ \Omega} \implies R_{\text{total}} = \frac{120\ \Omega}{2} = 60.0\ \Omega R total 1 = R 1 1 + R 2 1 = 120 Ω 1 + 120 Ω 1 = 120 Ω 2 ⟹ R total = 2 120 Ω = 60.0 Ω
Or via the product-over-sum formula: R total = R 1 × R 2 R 1 + R 2 = 120 × 120 120 + 120 = 14 , 400 240 = 60.0 Ω R_{\text{total}} = \frac{R_1 \times R_2}{R_1 + R_2} = \frac{120 \times 120}{120 + 120} = \frac{14,400}{240} = 60.0\ \Omega R total = R 1 + R 2 R 1 × R 2 = 120 + 120 120 × 120 = 240 14 , 400 = 60.0 Ω
Step-by-Step DMM Resistance Testing Protocol (Key-OFF)
Bus termination resistance testing is the primary initial diagnostic test for any CAN bus failure:
Turn the machine ignition switch to OFF .
Disconnect the battery negative cable or switch the master battery disconnect switch to OFF. This ensures the digital multimeter (DMM) does not pass test current through live circuits, which produces inaccurate resistance readings and can damage the meter.
Connect the DMM test leads across CAN_H (Pin C) and CAN_L (Pin D) at the 9-pin Deutsch diagnostic service port (or at any convenient breakout tee on the backbone).
Measured Bus Resistance Electrical State of CAN Bus Diagnostic Root Cause & Required Action
60 Ω ± 3 Ω 60\ \Omega \pm 3\ \Omega 60 Ω ± 3 Ω ( 57 to 63 Ω 57\text{ to }63\ \Omega 57 to 63 Ω ) Healthy / Nominal Termination Both 120 Ω 120\ \Omega 120 Ω terminating resistors are present, connected in parallel, and functional. Backbone continuity is intact between both ends.
120 Ω ± 5 Ω 120\ \Omega \pm 5\ \Omega 120 Ω ± 5 Ω Single Terminator Active Exactly one terminating resistor is disconnected, missing, or internally open, OR the backbone harness is severed between the test point and one end of the machine. Data corruption will occur due to signal reflections.
40 Ω ± 2 Ω 40\ \Omega \pm 2\ \Omega 40 Ω ± 2 Ω Over-Terminated (Three Resistors) An unauthorized third 120 Ω 120\ \Omega 120 Ω terminating resistor is present on the bus ( 1 R T = 1 120 + 1 120 + 1 120 = 3 120 ⟹ 40 Ω \frac{1}{R_T} = \frac{1}{120} + \frac{1}{120} + \frac{1}{120} = \frac{3}{120} \implies 40\ \Omega R T 1 = 120 1 + 120 1 + 120 1 = 120 3 ⟹ 40 Ω ). Occurs frequently when an aftermarket display, GPS modem, or payload scale with an unconfigured internal terminator is installed. Overloads transceivers.
0 Ω to 5 Ω 0\ \Omega\text{ to }5\ \Omega 0 Ω to 5 Ω Short Circuit Between Bus Lines Direct short between CAN_H and CAN_L (harness pinched under frame rail, water intrusion in connector cavity, or internally shorted transceiver chip). Communication is totally disabled across all ECMs.
O L OL O L (Infinite Resistance) Total Bus Open Circuit Both terminating resistors are missing/disconnected, or the backbone wiring has a dual-wire open circuit on both sides of the diagnostic port.
Differential Operating Voltages & Transceiver States
CAN transceivers communicate by driving the differential voltage between the two lines between two distinct electrical states: Recessive (logical 1) and Dominant (logical 0) . CAN DIFFERENTIAL VOLTAGE STATES
- Voltage
- 4.0V ──
- 3.5V ── ┌─────────────────┐ (CAN_High Dominant = 3.5V)
- 3.0V ── │ │
- 2.5V ── ────────────┘ └──────────── (Recessive Baseline = 2.5V)
- 2.0V ── ────────────┐ ┌──────────── (Recessive Baseline = 2.5V)
- 1.5V ── │ │
- 1.0V ── └─────────────────┘ (CAN_Low Dominant = 1.5V)
- 0V ──
- ◄─ Recessive ─►◄─── Dominant ──►◄─ Recessive ─►
- Differential 0V Differential 2V Differential 0V
- (Bit = 1) (Bit = 0) (Bit = 1)
- 1. Recessive State (Logical 1 / Bus Idle)
When no controller is actively transmitting, or when transmitting a logical "1" bit, internal biasing resistors inside every connected transceiver pull both CAN_H and CAN_L to an identical DC potential: V CAN_H = 2.50 V , V CAN_L = 2.50 V V_{\text{CAN\_H}} = 2.50\text{ V}, \quad V_{\text{CAN\_L}} = 2.50\text{ V} V CAN_H = 2.50 V , V CAN_L = 2.50 V
The resulting differential voltage is exactly zero: V diff = V CAN_H − V CAN_L = 2.50 V − 2.50 V = 0.00 V V_{\text{diff}} = V_{\text{CAN\_H}} - V_{\text{CAN\_L}} = 2.50\text{ V} - 2.50\text{ V} = 0.00\text{ V} V diff = V CAN_H − V CAN_L = 2.50 V − 2.50 V = 0.00 V
2. Dominant State (Logical 0 / Active Bit)
When an ECM transmits a logical "0" bit, its internal transceiver activates solid-state switching transistors:
The high-side driver pulls CAN_H up to + 3.50 V +3.50\text{ V} + 3.50 V (nominal range 2.75 V to 4.50 V 2.75\text{ V to }4.50\text{ V} 2.75 V to 4.50 V ).
The low-side driver pulls CAN_L down to + 1.50 V +1.50\text{ V} + 1.50 V (nominal range 0.50 V to 2.25 V 0.50\text{ V to }2.25\text{ V} 0.50 V to 2.25 V ).
This generates a robust differential voltage of approximately 2.00 V 2.00\text{ V} 2.00 V : V diff = V CAN_H − V CAN_L = 3.50 V − 1.50 V = 2.00 V V_{\text{diff}} = V_{\text{CAN\_H}} - V_{\text{CAN\_L}} = 3.50\text{ V} - 1.50\text{ V} = 2.00\text{ V} V diff = V CAN_H − V CAN_L = 3.50 V − 1.50 V = 2.00 V
Receiver Thresholds
Every transceiver receiver contains a high-speed differential comparator:
If V diff < 0.50 V V_{\text{diff}} < 0.50\text{ V} V diff < 0.50 V , the receiver decodes a Recessive Bit (1) .
If V diff > 0.90 V V_{\text{diff}} > 0.90\text{ V} V diff > 0.90 V , the receiver decodes a Dominant Bit (0) .
DMM Voltage Testing (Key-ON, Engine Running)
While high-speed bits switch in microseconds, a standard DMM measures the time-averaged DC voltage. With the ignition switch ON and healthy communication occurring:
Measure CAN_H to Chassis Ground: Normal reading is 2.60 V to 3.00 V 2.60\text{ V to }3.00\text{ V} 2.60 V to 3.00 V DC (average of 2.5 V 2.5\text{ V} 2.5 V recessive and 3.5 V 3.5\text{ V} 3.5 V dominant pulses).
Measure CAN_L to Chassis Ground: Normal reading is 2.00 V to 2.40 V 2.00\text{ V to }2.40\text{ V} 2.00 V to 2.40 V DC (average of 2.5 V 2.5\text{ V} 2.5 V recessive and 1.5 V 1.5\text{ V} 1.5 V dominant pulses).
The 5.0-Volt Summation Rule: Because the transceiver drives CAN_H upward and CAN_L downward symmetrically by an equal voltage delta, the sum of the two line voltages must always equal approximately 5.00 V 5.00\text{ V} 5.00 V ( 2.7 V + 2.3 V = 5.0 V 2.7\text{ V} + 2.3\text{ V} = 5.0\text{ V} 2.7 V + 2.3 V = 5.0 V ). If the sum deviates significantly from 5.0 V 5.0\text{ V} 5.0 V (e.g., V H = 3.8 V , V L = 2.5 V ⟹ 6.3 V V_H = 3.8\text{ V}, V_L = 2.5\text{ V} \implies 6.3\text{ V} V H = 3.8 V , V L = 2.5 V ⟹ 6.3 V ), a short to power or ground offset fault is confirmed.
Non-Destructive Bitwise Arbitration & Priority Framing
CAN is a multi-master broadcast network —any controller can initiate transmission whenever the bus is idle. But what happens when two controllers attempt to transmit simultaneously?
The 29-Bit Identifier Structure
SAE J1939 uses an extended 29-bit message identifier format containing four distinct fields:
Priority (3 bits): Values 0 to 7 0\text{ to }7 0 to 7 ( 0 0 0 is highest priority, 7 7 7 is lowest priority).
Parameter Group Number - PGN (18 bits): Defines the message content (e.g., PGN 61444 = Electronic Engine Controller 1 / Engine Speed).
Source Address - SA (8 bits): Identifies the transmitting controller (e.g., Address 0 = Engine #1, Address 3 = Transmission, Address 49 = Cab Display). NON-DESTRUCTIVE BITWISE ARBITRATION
- Bit Time: 1 2 3 4 5 (Node B Backs Off!)
- Node A (Eng): 0 0 1 0 0 (Transmits Dominant 0)
- Node B (Disp): 0 0 1 0 1 (Transmits Recessive 1)
- ═════════════════════════════════════════════════
- Bus State: 0 0 1 0 0 (Dominant 0 Overwrites 1)
- ▲
- │ Node B detects mismatch,
│ halts transmission immediately.
The Arbitration Mechanism
Arbitration occurs bit-by-bit during the transmission of the 29-bit identifier:
In CAN transceiver physical logic, a Dominant bit (0) physically overpowers a Recessive bit (1) on the differential bus wire. If one node drives a 0 (differential voltage 2.0 V 2.0\text{ V} 2.0 V ) and another node floats a 1 (differential voltage 0.0 V 0.0\text{ V} 0.0 V ), the bus physically sits at 2.0 V 2.0\text{ V} 2.0 V (dominant 0).
Every transmitting controller simultaneously listens to the bus state via its internal receiver while driving each bit.
When Node A (Engine ECM transmitting Priority 3) and Node B (Cab Display transmitting Priority 6) transmit simultaneously, they output identical bits until bit position 5. At bit 5, Node A drives a dominant 0, while Node B outputs a recessive 1.
Node B monitors the bus and detects that the physical bus is dominant (0) when it attempted to send a recessive (1). Node B instantly recognizes that a higher-priority message is contesting the bus.
Node B ceases transmission immediately in mid-bit without corrupting Node A's frame, and transitions into a receiver. Node A completes its message transmission without a single microsecond of latency or data loss. Once the bus becomes idle, Node B re-arbitrates and transmits its message.