Study guide

13.1 Belt Conveyors: Components, Tracking & Training

Red Seal Industrial Mechanic Millwright

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety & Occupational Skills

1.1 WHMIS, SDS & Hazardous Materials 1.2 Lockout/Tagout (LOTO) & Energy Isolation 1.3 Confined Space Entry & Fall Protection 1.4 Blueprint Reading, Trade Math & Precision Measurement Tools 1.5 Hand Tools, Portable Power Tools & Shop Machines 1.6 Access Equipment: Ladders, Scaffolds & Elevating Work Platforms 1.7 Planning Work, Permits, Communication & Mentoring

2 Chapter 2: Fasteners & Bolted Joints

2.1 Threaded Fasteners, Bolts & Thread Standards 2.2 Torque Values, Tightening Patterns & Thread Pitch/Gaging 2.3 Non-Threaded Fasteners, Pins, Keys & Anchors

3 Chapter 3: Rigging, Hoisting & Crane Signals

3.1 Sling Angles, Sling Types & Leg Tension Calculations 3.2 Working Load Limit (WLL) & Hardware Inspection 3.3 Centre of Gravity & Load Weight Estimation 3.4 Hoists, Overhead Cranes & Standard Hand Signals 3.5 Jacking, Skidding, Rollers & Moving Equipment 3.6 Lift Planning, Area Control & Rigging Equipment Maintenance

4 Chapter 4: Prime Movers & Electric Motors

4.1 Electric Motors, Enclosures, Frame Sizes & Synchronous Speed 4.2 Motor Installation, Nameplates & Overload Protection 4.3 Engine Prime Movers & Mechanical Drives Introduction

5 Chapter 5: Belt & Chain Mechanical Drives

5.1 V-Belts, Timing Belts & Sheave Alignment 5.2 Belt Tensioning, Pitch Diameter & Speed Ratios 5.3 Roller Chains, Sprocket Alignment & Lubrication 5.4 Clutches, Brakes & Torque Limiters

6 Chapter 6: Gear Drives, Couplings & Reducers

6.1 Gear Types, Geometry & Gear Ratios 6.2 Couplings (Rigid, Flexible, Fluid) & Installation 6.3 Shaft Keys, Keyways, Taper Sleeves & Hub Fits 6.4 Gear Reducers, Backlash & Mechanical Drive Troubleshooting

7 Chapter 7: Industrial Pumps & Systems

7.1 Centrifugal Pumps, Impellers & Performance Curves 7.2 Positive Displacement Pumps (Gear, Vane, Piston, Diaphragm) 7.3 Cavitation, NPSHa vs NPSHr & Pump Priming 7.4 Pump Maintenance, Packing & Mechanical Seals

8 Chapter 8: Compressors, Fans & Pneumatics

8.1 Reciprocating & Rotary Screw Air Compressors 8.2 Compressed Air Treatment, FRL Units & Air Receivers 8.3 Centrifugal & Axial Fans, Affinity Laws & Airflow 8.4 Pneumatic Circuits, Valves, Actuators & Troubleshooting 8.5 Vacuum Systems, Pumps & Venturi Generators

9 Chapter 9: Bearings, Lubrication & Seals

9.1 Plain Bearings, Bushings & Fits 9.2 Rolling Element Bearings & Installation 9.3 Bearing Heating Limits, Fits & Removal Tools 9.4 Industrial Lubricants, Viscosity, Grease NLGI Grades & Seals

10 Chapter 10: Precision Alignment & Foundations

10.1 Precision Shaft Alignment (Rim-and-Face & Reverse-Dial Methods) 10.2 Laser Alignment, Soft Foot Correction & Thermal Growth 10.3 Machinery Foundations, Leveling, Grouting & Dowelling

11 Chapter 11: Vibration Analysis & Predictive Maintenance

11.1 Vibration Analysis, Dynamic Balancing & Thermography 11.2 Preventive/Predictive Maintenance & Decommissioning 11.3 Non-Destructive Testing (NDT) Methods 11.4 Lubricant & Fluid Analysis 11.5 Commissioning: Pre-Start Checks, Run-In & Documentation

12 Chapter 12: Hydraulic Systems

12.1 Hydraulic Fundamentals: Pascal’s Law, Pressure, Flow & Power 12.2 Hydraulic Fluids, Reservoirs, Filtration & Contamination Control 12.3 Hydraulic Pumps: Gear, Vane & Piston Designs 12.4 Hydraulic Valves: Pressure, Directional & Flow Control 12.5 Hydraulic Actuators: Cylinders, Motors & Accumulators 12.6 Hydraulic Conductors, ISO 1219 Symbols & System Troubleshooting

13 Chapter 13: Conveying Systems, Material Handling & Automation

13.1 Belt Conveyors: Components, Tracking & Training 13.2 Screw, Bucket, Roller, Chain & Pneumatic Conveyors 13.3 Robotics & Automated Equipment

14 Chapter 14: Process Piping, Tanks & Vessels

14.1 Process Piping: Materials, Sizing, Fittings & Joining 14.2 Flanges, Gaskets & Piping Bolted-Joint Assembly 14.3 Tanks, Vessels & Containers: Installation, Inspection & Repair

15 Chapter 15: Materials, Fabrication, Cutting & Welding

15.1 Material Identification: Ferrous & Non-Ferrous Metals, Plastics 15.2 Heat Treatment of Metals 15.3 Oxy-Fuel & Plasma Arc Cutting 15.4 Welding Processes: SMAW, GMAW, GTAW, OFW & Equipment Care 15.5 Layout Procedures & Maintaining Precision Measuring Tools

13.1 Belt Conveyors: Components, Tracking & Training

Key Takeaways Explain This Topic AI

A belt always moves toward the end of an idler or pulley that it contacts first, which is the governing rule for every tracking correction.

Train a belt starting at the tail and working toward the head, adjusting no more than about 3 mm at a time and running several full belt revolutions between adjustments.

Correct belt sag between troughing idlers is 2–3% of idler spacing; more sag spills material and accelerates idler wear, less sag overtightens the belt.

Gravity take-ups provide constant tension automatically, while screw take-ups must be adjusted manually and are limited to short conveyors under roughly 45 m.

Head pulley lagging is grooved in a herringbone or diamond pattern with the apex pointing in the direction of belt travel so trapped water and fines are shed outward.

Last updated: August 2026

Task D-20 (Services conveying systems) carries 5 of the 135 exam questions, and belt conveyors dominate that task. In sawmills, mines, aggregate plants, grain terminals and food plants, the millwright is the trade that installs, aligns, tracks and repairs them.

Conveyor Components TYPICAL TROUGHED BELT CONVEYOR (side elevation)

  • Loading skirtboard Primary belt scraper
  • | |
  • v carrying run (troughing idlers, 20/35/45 deg) v
  • [ ]==*==*==*==*==*==*==*==*==*==*==*==*==*==*==*==*==*==*==*==[ HEAD ]---> discharge
  • ^ [PULLEY ]
  • TAIL PULLEY (driven, lagged)
  • ^ |
  • | return run (flat return idlers, wider spacing) v
  • +----o---------o---------o---------o---------o------[SNUB]---[BEND]
  • | |
  • GRAVITY TAKE-UP (vertical counterweight)-------+
  • Component Function Service points
  • Head pulley Drive pulley at the discharge; usually lagged Lagging wear, shaft alignment, bearing lubrication

Tail pulley Return/turn-around at the loading end; often winged to shed material Material buildup, seized bearings

  • Snub pulley Increases the wrap angle on the drive pulley to raise available friction Alignment; must be square
  • Bend pulley Redirects the belt around the take-up Alignment and buildup
  • Take-up Maintains belt tension and absorbs stretch Free travel; counterweight must hang clear
  • Troughing idlers Support the loaded run in a 20, 35 or 45 degree trough Seized rollers, shell wear-through
  • Impact idlers Rubber-cushioned rollers under the loading point Cushion condition
  • Return idlers Support the empty run, spaced roughly twice as far apart Buildup causing mistracking

Training idlers Self-aligning rollers that pivot to steer the belt Free pivot; not a substitute for squaring the frame

  • Belt cleaners Primary scraper at the head pulley face, secondary below Blade wear and tension
  • Skirtboard and seal Contains material at the loading zone Rubber seal wear scoring the belt
  • Belt Construction and Splicing

A conveyor belt is a carcass (plies of polyester/nylon fabric, steel cord for long high-tension runs) bonded between a top cover (thicker, takes impact and abrasion) and a bottom cover (thin, runs on idlers). Belts are specified by width, ply count or steel cord rating, cover thickness in millimetres, and cover compound (general purpose, oil-resistant, heat-resistant, fire-resistant/FRAS for underground).

Splice type Strength retained Notes

Mechanical fastener (hinged or plate) 35–50% of belt rating Fast, repairable in place, allows belt removal; leaks fines, damages cleaners

  • Cold vulcanized (adhesive) 60–80% No heat source needed; sensitive to temperature and cleanliness
  • Hot vulcanized (heated press) 90–100% Strongest and smoothest; requires a vulcanizing press and time

A square splice is essential. An out-of-square splice makes the belt run to one side each time the splice passes a pulley, producing a mistrack that appears and disappears once per belt revolution — a distinctive diagnostic signature.

Belt Tracking: The Governing Rule

A belt moves toward the end of the idler or pulley that it contacts first.

Everything about training follows from that one statement. If the leading (first-contacted) end of an idler is skewed forward in the direction of belt travel, the belt migrates toward that end. DIRECTION OF BELT TRAVEL ------------------------>

Idler skewed like this: Belt drifts this way:

  • / ^
  • =====/===== |
  • / toward the
  • (left end advanced forward) LEFT (advanced) end
  • Causes of Mistracking, in Order of Frequency

Off-centre loading — material dropped to one side of the belt. Fix the chute, not the idlers. This is the single most common cause.

Material buildup on pulleys and idler shells — creates a local crown that steers the belt. Fix the cleaners.

Frame out of square or out of level — the belt follows the geometry. Check with a string line and level before touching anything.

Seized idler rollers — a locked roller drags one side.

Out-of-square splice — mistrack recurs once per belt revolution.

Belt camber (a bowed belt) — new belt stored improperly, or a belt cut from a bad roll.

Training Procedure

Correct the causes first. Clean buildup, free seized rollers, square and level the structure, and fix the loading point. Idler skewing cannot compensate for a crooked frame.

Run the empty belt and mark where it runs off. Then run it loaded — a belt that tracks empty but not loaded is almost always a loading-point problem.

Work from tail to head , in the direction of belt travel.

Adjust the idlers in the region where the belt begins to drift , not where it is already off. Adjust roughly one idler in every ten, and never more than about 3 mm (1/8 in) per adjustment.

Wait several complete belt revolutions after each change before judging the result. A long conveyor may need many minutes.

Use self-aligning training idlers on both the carrying and return runs for continuing control, but only after the structure and loading are correct.

Never attempt tracking adjustments with bare hands near a moving belt, and never use a pry bar against a running belt. Where a belt must be observed running, use the designated observation points outside the guarding.

Belt Tension, Sag and Take-Ups

Correct tension is the minimum that (a) transmits the drive torque without slip and (b) limits sag between idlers to 2–3% of the idler spacing . Excessive sag lets material tumble and spill and hammers the idlers; insufficient sag overloads bearings, splices and the belt carcass.

Take-up type Operation Application

Screw (manual) Threaded rods pull the tail pulley back; adjusted by hand Short conveyors, roughly under 45 m; requires periodic re-adjustment

Gravity (counterweight) A weighted carriage rides a vertical or horizontal frame Automatic constant tension; standard for long conveyors

Hydraulic / winch Powered tensioner with pressure control Long overland or high-tension conveyors

Take-up travel must accommodate belt stretch — commonly 1.5–2% of belt length for fabric belts , far less for steel-cord belts. When adjusting a screw take-up, move both sides equally and measure; unequal adjustment is itself a tracking error.

Drive, Lagging and Wrap

Available drive friction depends on the coefficient of friction, the arc of wrap on the drive pulley, and the slack-side tension. A snub pulley raises the wrap from 180 degrees to 210–240 degrees. Lagging — bonded or vulcanized rubber, or ceramic tiles for wet abrasive duty — raises the friction coefficient and improves wet-condition traction. Grooved lagging patterns (herringbone or diamond) must be installed with the apex pointing in the direction of belt travel so water and fines are pushed outward and shed off the pulley ends.

Mandatory Safety Devices

Conveying systems are a high-injury area. Sub-task requirements tie directly to Task A-1:

Nip-point guards at every pulley, at the drive, and wherever the belt approaches a roller.

Pull-cord (lanyard) emergency stops running the accessible length of the conveyor, with latching stop switches.

Zero-speed / belt-slip switch to shut down the drive if the belt stops while the motor runs.

Belt misalignment switches and plugged-chute detectors on enclosed systems.

Anti-runback (backstop) devices on inclined conveyors so a loaded belt cannot reverse when power is lost.

Full lock-out/tag-out including gravity take-up blocking. A counterweight is stored energy: it must be blocked or lowered and secured before any belt work.