Study guide

13.2 Screw, Bucket, Roller, Chain & Pneumatic Conveyors

Red Seal Industrial Mechanic Millwright

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety & Occupational Skills

1.1 WHMIS, SDS & Hazardous Materials 1.2 Lockout/Tagout (LOTO) & Energy Isolation 1.3 Confined Space Entry & Fall Protection 1.4 Blueprint Reading, Trade Math & Precision Measurement Tools 1.5 Hand Tools, Portable Power Tools & Shop Machines 1.6 Access Equipment: Ladders, Scaffolds & Elevating Work Platforms 1.7 Planning Work, Permits, Communication & Mentoring

2 Chapter 2: Fasteners & Bolted Joints

2.1 Threaded Fasteners, Bolts & Thread Standards 2.2 Torque Values, Tightening Patterns & Thread Pitch/Gaging 2.3 Non-Threaded Fasteners, Pins, Keys & Anchors

3 Chapter 3: Rigging, Hoisting & Crane Signals

3.1 Sling Angles, Sling Types & Leg Tension Calculations 3.2 Working Load Limit (WLL) & Hardware Inspection 3.3 Centre of Gravity & Load Weight Estimation 3.4 Hoists, Overhead Cranes & Standard Hand Signals 3.5 Jacking, Skidding, Rollers & Moving Equipment 3.6 Lift Planning, Area Control & Rigging Equipment Maintenance

4 Chapter 4: Prime Movers & Electric Motors

4.1 Electric Motors, Enclosures, Frame Sizes & Synchronous Speed 4.2 Motor Installation, Nameplates & Overload Protection 4.3 Engine Prime Movers & Mechanical Drives Introduction

5 Chapter 5: Belt & Chain Mechanical Drives

5.1 V-Belts, Timing Belts & Sheave Alignment 5.2 Belt Tensioning, Pitch Diameter & Speed Ratios 5.3 Roller Chains, Sprocket Alignment & Lubrication 5.4 Clutches, Brakes & Torque Limiters

6 Chapter 6: Gear Drives, Couplings & Reducers

6.1 Gear Types, Geometry & Gear Ratios 6.2 Couplings (Rigid, Flexible, Fluid) & Installation 6.3 Shaft Keys, Keyways, Taper Sleeves & Hub Fits 6.4 Gear Reducers, Backlash & Mechanical Drive Troubleshooting

7 Chapter 7: Industrial Pumps & Systems

7.1 Centrifugal Pumps, Impellers & Performance Curves 7.2 Positive Displacement Pumps (Gear, Vane, Piston, Diaphragm) 7.3 Cavitation, NPSHa vs NPSHr & Pump Priming 7.4 Pump Maintenance, Packing & Mechanical Seals

8 Chapter 8: Compressors, Fans & Pneumatics

8.1 Reciprocating & Rotary Screw Air Compressors 8.2 Compressed Air Treatment, FRL Units & Air Receivers 8.3 Centrifugal & Axial Fans, Affinity Laws & Airflow 8.4 Pneumatic Circuits, Valves, Actuators & Troubleshooting 8.5 Vacuum Systems, Pumps & Venturi Generators

9 Chapter 9: Bearings, Lubrication & Seals

9.1 Plain Bearings, Bushings & Fits 9.2 Rolling Element Bearings & Installation 9.3 Bearing Heating Limits, Fits & Removal Tools 9.4 Industrial Lubricants, Viscosity, Grease NLGI Grades & Seals

10 Chapter 10: Precision Alignment & Foundations

10.1 Precision Shaft Alignment (Rim-and-Face & Reverse-Dial Methods) 10.2 Laser Alignment, Soft Foot Correction & Thermal Growth 10.3 Machinery Foundations, Leveling, Grouting & Dowelling

11 Chapter 11: Vibration Analysis & Predictive Maintenance

11.1 Vibration Analysis, Dynamic Balancing & Thermography 11.2 Preventive/Predictive Maintenance & Decommissioning 11.3 Non-Destructive Testing (NDT) Methods 11.4 Lubricant & Fluid Analysis 11.5 Commissioning: Pre-Start Checks, Run-In & Documentation

12 Chapter 12: Hydraulic Systems

12.1 Hydraulic Fundamentals: Pascal’s Law, Pressure, Flow & Power 12.2 Hydraulic Fluids, Reservoirs, Filtration & Contamination Control 12.3 Hydraulic Pumps: Gear, Vane & Piston Designs 12.4 Hydraulic Valves: Pressure, Directional & Flow Control 12.5 Hydraulic Actuators: Cylinders, Motors & Accumulators 12.6 Hydraulic Conductors, ISO 1219 Symbols & System Troubleshooting

13 Chapter 13: Conveying Systems, Material Handling & Automation

13.1 Belt Conveyors: Components, Tracking & Training 13.2 Screw, Bucket, Roller, Chain & Pneumatic Conveyors 13.3 Robotics & Automated Equipment

14 Chapter 14: Process Piping, Tanks & Vessels

14.1 Process Piping: Materials, Sizing, Fittings & Joining 14.2 Flanges, Gaskets & Piping Bolted-Joint Assembly 14.3 Tanks, Vessels & Containers: Installation, Inspection & Repair

15 Chapter 15: Materials, Fabrication, Cutting & Welding

15.1 Material Identification: Ferrous & Non-Ferrous Metals, Plastics 15.2 Heat Treatment of Metals 15.3 Oxy-Fuel & Plasma Arc Cutting 15.4 Welding Processes: SMAW, GMAW, GTAW, OFW & Equipment Care 15.5 Layout Procedures & Maintaining Precision Measuring Tools

13.2 Screw, Bucket, Roller, Chain & Pneumatic Conveyors

Key Takeaways Explain This Topic AI

Screw conveyor capacity falls sharply with incline, dropping roughly 30% at 15 degrees and about 55% at 25 degrees, so inclined screws must be re-rated.

Hanger bearings are the highest-wear item in a screw conveyor and must be selected for the material — hardened, wood, or self-lubricating — never standard rolling-element bearings.

Every inclined bucket elevator requires an anti-runback backstop so a loaded leg cannot reverse and dump its load into the boot on power loss.

Centrifugal-discharge bucket elevators run at high speed with spaced buckets; continuous-discharge elevators run slowly with buckets nested to protect fragile material.

Dilute-phase pneumatic conveying uses high air velocity at low pressure and suspends the material, while dense-phase uses low velocity at high pressure and moves the material in slugs.

Last updated: August 2026

Belt conveyors are only one part of Task D-20 . Process plants move product by screw, bucket, chain, roller and air, and each has its own failure signature.

Screw Conveyors (Augers)

A screw conveyor is a helical flight welded to a pipe or shaft, rotating in a U-shaped or tubular trough , pushing material axially.

Part Notes

Flighting Sectional or helicoid; hard-surfaced for abrasives; may be ribbon (sticky materials) or cut-and-folded (mixing)

  • Coupling shafts and bolts Join screw sections; bolts are a wear item and shear if the conveyor is jammed
  • Hanger bearings Support intermediate joints inside the material stream — the highest-wear component
  • End bearings and seals Carry thrust; thrust bearing is placed at the discharge end so the screw is in tension
  • Trough and cover Bolted covers must be interlocked or bolted with tools-required fasteners

Hanger bearing selection is a favourite exam point. These bearings run submerged in the conveyed product, so a sealed ball bearing would be destroyed immediately. Choices are hard-iron or hardened-steel bushings for abrasives, oil-impregnated bronze or hardwood (rock maple) for grain and food service, and UHMW or nylon for corrosive or wash-down duty. Hanger bearings must be inspected on a scheduled interval because a failed hanger lets the screw drop and grind the trough through.

Incline de-rating: capacity is calculated for horizontal service and falls quickly as the screw is inclined, because material rolls back over the flight. Approximate loss is about 10% at 5 degrees, 30% at 15 degrees, and 55% at 25 degrees; above roughly 30 degrees a tubular housing with close-clearance flighting is required.

Trough loading is limited by material: about 45% for light free-flowing product, 30% for average, and 15% for abrasive or sluggish material. Overloading a screw stalls it, shears coupling bolts and destroys hanger bearings.

Safety: an open screw conveyor is one of the most lethal machines in a plant. Covers must be secured, guarded and interlocked, and lock-out is mandatory before removing any cover.

Bucket Elevators

A bucket elevator raises bulk material vertically using buckets on a belt or chain running between a head section and a boot section.

Type Speed Discharge mechanism Suits

Centrifugal High (roughly 1.2–2.0 m/s belt speed) Material thrown out by centrifugal force at the head pulley; buckets spaced apart Free-flowing granular material — grain, sand, cement

Continuous Low Material slides over the back of the preceding bucket; buckets nested Fragile, abrasive or aerated material

Positive discharge Low Buckets snubbed back and inverted over the head Sticky or slow-flowing material

Critical service points:

Backstop (anti-runback): mandatory. Without it, a loss of power on a loaded leg lets the whole column run backward and pile into the boot, wrecking the machine and creating a serious hazard on restart.

Boot take-up: tensions the belt or chain; must be adjusted evenly on both sides.

Boot cleanout and inspection door: buildup in the boot causes belt slip and heat.

Explosion protection: grain, sugar, flour, coal and many other dusts are combustible. Elevator legs commonly carry explosion relief panels, bearing temperature sensors, belt-alignment and belt-slip switches. Bearing temperature monitoring and belt-slip detection are dust-explosion prevention devices, not just maintenance conveniences.

  • Roller and Chain Conveyors
  • Roller Conveyors

Type Drive Notes

Gravity roller None — slope Typical pitch 1.5–3% depending on load; roller centres must give at least three rollers under the shortest package

Belt-driven live roller (BDLR) Flat belt pressed against the roller undersides Quiet, gentle; belt tension via pressure rollers

  • Chain-driven live roller (CDLR) Roll-to-roll chain loops Heavy loads, pallets, hot or dirty environments
  • Line-shaft Spools and urethane bands off a common shaft Low cost, light duty, slip-band overload protection

Motorized drive roller (MDR) 24 V DC motor inside a roller, zoned control Zero-pressure accumulation, energy efficient

Roller conveyor faults a millwright fixes: seized bearings (a single locked roller scuffs product and stalls light loads), out-of-square frames causing product skew, worn drive bands, and incorrect roller pitch after a product change.

Chain and Drag Conveyors

Apron / pan conveyors — overlapping steel pans on two strands of heavy chain; used for hot, sharp or very heavy material such as forgings or foundry sand.

Slat conveyors — slats on chain, used in assembly and bottling.

Drag / en-masse conveyors — flights on a chain pull material through an enclosed trough; compact and dust-tight, common in grain and biomass.

Overhead trolley conveyors — enclosed-track or I-beam trolleys on chain for paint lines and meat processing.

Chain conveyor service centres on chain elongation (measure over a defined number of pitches; replace at roughly 2–3% elongation), sprocket tooth hooking, correct catenary sag, and lubrication compatible with the product. Both strands on a two-strand conveyor must be tensioned and phased identically or the flights will run crooked and gouge the trough.

Pneumatic Conveying

Pneumatic systems move dry bulk powder and granules through pipe using air.

Mode Air velocity Pressure Behaviour Suits

Dilute phase High (roughly 15–35 m/s) Low (under about 100 kPa) Particles fully suspended in the air stream Non-abrasive, non-fragile powders; long routing flexibility

Dense phase Low (roughly 2–10 m/s) High (up to about 600 kPa) Material moves as slugs or plugs along the pipe bottom Abrasive or friable products; lower product degradation and pipe wear

System types are pressure (push) from a blower or compressor, vacuum (pull) using a vacuum blower and receiver, or combined. Key components include the blower or compressor, the rotary airlock (rotary valve) that meters material into a pressurized line while sealing against air blow-back, diverter valves, the receiving cyclone or filter receiver, and the bin vent filter.

Rotary airlock service is core millwright work: vane-tip-to-housing clearance is typically 0.1–0.2 mm and must be measured and restored, because worn clearance lets conveying air blow back through the valve, killing throughput. Airlocks are also a severe amputation hazard and must be locked out and the inlet chute cleared before any hand enters the housing.

Pneumatic system troubleshooting: a line plug is usually caused by velocity dropping below the material's saltation velocity — too little air, a leaking airlock, a partially closed diverter, or a wet product. Excessive pipe elbow wear indicates dilute-phase velocity that is too high for an abrasive product; long-radius or ceramic-lined elbows are the fix.