Study guide

12.5 Hydraulic Actuators: Cylinders, Motors & Accumulators

Red Seal Industrial Mechanic Millwright

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety & Occupational Skills

1.1 WHMIS, SDS & Hazardous Materials 1.2 Lockout/Tagout (LOTO) & Energy Isolation 1.3 Confined Space Entry & Fall Protection 1.4 Blueprint Reading, Trade Math & Precision Measurement Tools 1.5 Hand Tools, Portable Power Tools & Shop Machines 1.6 Access Equipment: Ladders, Scaffolds & Elevating Work Platforms 1.7 Planning Work, Permits, Communication & Mentoring

2 Chapter 2: Fasteners & Bolted Joints

2.1 Threaded Fasteners, Bolts & Thread Standards 2.2 Torque Values, Tightening Patterns & Thread Pitch/Gaging 2.3 Non-Threaded Fasteners, Pins, Keys & Anchors

3 Chapter 3: Rigging, Hoisting & Crane Signals

3.1 Sling Angles, Sling Types & Leg Tension Calculations 3.2 Working Load Limit (WLL) & Hardware Inspection 3.3 Centre of Gravity & Load Weight Estimation 3.4 Hoists, Overhead Cranes & Standard Hand Signals 3.5 Jacking, Skidding, Rollers & Moving Equipment 3.6 Lift Planning, Area Control & Rigging Equipment Maintenance

4 Chapter 4: Prime Movers & Electric Motors

4.1 Electric Motors, Enclosures, Frame Sizes & Synchronous Speed 4.2 Motor Installation, Nameplates & Overload Protection 4.3 Engine Prime Movers & Mechanical Drives Introduction

5 Chapter 5: Belt & Chain Mechanical Drives

5.1 V-Belts, Timing Belts & Sheave Alignment 5.2 Belt Tensioning, Pitch Diameter & Speed Ratios 5.3 Roller Chains, Sprocket Alignment & Lubrication 5.4 Clutches, Brakes & Torque Limiters

6 Chapter 6: Gear Drives, Couplings & Reducers

6.1 Gear Types, Geometry & Gear Ratios 6.2 Couplings (Rigid, Flexible, Fluid) & Installation 6.3 Shaft Keys, Keyways, Taper Sleeves & Hub Fits 6.4 Gear Reducers, Backlash & Mechanical Drive Troubleshooting

7 Chapter 7: Industrial Pumps & Systems

7.1 Centrifugal Pumps, Impellers & Performance Curves 7.2 Positive Displacement Pumps (Gear, Vane, Piston, Diaphragm) 7.3 Cavitation, NPSHa vs NPSHr & Pump Priming 7.4 Pump Maintenance, Packing & Mechanical Seals

8 Chapter 8: Compressors, Fans & Pneumatics

8.1 Reciprocating & Rotary Screw Air Compressors 8.2 Compressed Air Treatment, FRL Units & Air Receivers 8.3 Centrifugal & Axial Fans, Affinity Laws & Airflow 8.4 Pneumatic Circuits, Valves, Actuators & Troubleshooting 8.5 Vacuum Systems, Pumps & Venturi Generators

9 Chapter 9: Bearings, Lubrication & Seals

9.1 Plain Bearings, Bushings & Fits 9.2 Rolling Element Bearings & Installation 9.3 Bearing Heating Limits, Fits & Removal Tools 9.4 Industrial Lubricants, Viscosity, Grease NLGI Grades & Seals

10 Chapter 10: Precision Alignment & Foundations

10.1 Precision Shaft Alignment (Rim-and-Face & Reverse-Dial Methods) 10.2 Laser Alignment, Soft Foot Correction & Thermal Growth 10.3 Machinery Foundations, Leveling, Grouting & Dowelling

11 Chapter 11: Vibration Analysis & Predictive Maintenance

11.1 Vibration Analysis, Dynamic Balancing & Thermography 11.2 Preventive/Predictive Maintenance & Decommissioning 11.3 Non-Destructive Testing (NDT) Methods 11.4 Lubricant & Fluid Analysis 11.5 Commissioning: Pre-Start Checks, Run-In & Documentation

12 Chapter 12: Hydraulic Systems

12.1 Hydraulic Fundamentals: Pascal’s Law, Pressure, Flow & Power 12.2 Hydraulic Fluids, Reservoirs, Filtration & Contamination Control 12.3 Hydraulic Pumps: Gear, Vane & Piston Designs 12.4 Hydraulic Valves: Pressure, Directional & Flow Control 12.5 Hydraulic Actuators: Cylinders, Motors & Accumulators 12.6 Hydraulic Conductors, ISO 1219 Symbols & System Troubleshooting

13 Chapter 13: Conveying Systems, Material Handling & Automation

13.1 Belt Conveyors: Components, Tracking & Training 13.2 Screw, Bucket, Roller, Chain & Pneumatic Conveyors 13.3 Robotics & Automated Equipment

14 Chapter 14: Process Piping, Tanks & Vessels

14.1 Process Piping: Materials, Sizing, Fittings & Joining 14.2 Flanges, Gaskets & Piping Bolted-Joint Assembly 14.3 Tanks, Vessels & Containers: Installation, Inspection & Repair

15 Chapter 15: Materials, Fabrication, Cutting & Welding

15.1 Material Identification: Ferrous & Non-Ferrous Metals, Plastics 15.2 Heat Treatment of Metals 15.3 Oxy-Fuel & Plasma Arc Cutting 15.4 Welding Processes: SMAW, GMAW, GTAW, OFW & Equipment Care 15.5 Layout Procedures & Maintaining Precision Measuring Tools

12.5 Hydraulic Actuators: Cylinders, Motors & Accumulators

Key Takeaways Explain This Topic AI

Cylinder mounting style determines rod alignment: centreline mounts (flange, tie-rod) absorb thrust in line, while foot mounts create an overturning moment unless keyed.

A stop tube is added to long-stroke cylinders to increase the separation between piston and rod bearing and prevent jackknifing at full extension.

Hydraulic motor torque (lb-in) equals displacement (in³/rev) times pressure differential (psi) divided by 6.28.

Gas-charged accumulators must be pre-charged with dry nitrogen only — never air or oxygen — because compressed oxygen in contact with oil can detonate.

A bladder accumulator used for energy storage is typically pre-charged to about 80–90% of minimum system pressure, measured with the hydraulic side fully discharged to tank.

Last updated: August 2026

Actuators convert fluid power back into mechanical work. Sub-task E-21.01/E-21.04 questions concentrate on installation geometry, seal selection, and the safety rules around stored energy in accumulators.

Cylinder Construction

A typical tie-rod industrial cylinder consists of a honed steel barrel, a cap end (blind end), a head end (rod-gland end), a piston with seals and wear bands, a hard-chrome-plated rod, a rod bearing (gland bushing), a rod seal, and a rod wiper that scrapes contamination off the retracting rod before it reaches the seal. Four tie rods clamp the assembly, torqued in a criss-cross pattern to the manufacturer's specification.

  • Cylinder type Construction Where used
  • Tie-rod Bolted end caps, fully rebuildable Standard industrial machinery to about 3,000 psi
  • Welded (mill-type) Welded end caps, heavy wall Mobile equipment, mills, high shock, higher pressure
  • Telescopic Nested stages of decreasing diameter Long stroke in a short retracted length — dump bodies, lifts

Ram (single-acting) One large-diameter moving element, no annulus Elevators, jacks, presses where gravity returns the load

Seal Materials

  • Elastomer Temperature range Compatible with Avoid
  • Nitrile (Buna-N) -40 C to 100 C Petroleum oil, water-glycol Phosphate ester, ozone
  • Viton (FKM) -20 C to 200 C Phosphate ester, high heat Low-temperature service, hot water/steam
  • Polyurethane -30 C to 80 C Petroleum oil, high abrasion High heat, water-based fluids
  • PTFE -100 C to 200 C Nearly everything Needs an energizer; poor elasticity
  • Mounting, Stop Tubes and Rod Buckling

Mounting style determines whether the rod stays aligned under load.

Centreline mounts — flange (cap or head), tie-rod extended, or centreline lug — put the reaction force on the same axis as the thrust and produce no bending moment.

Foot (side lug) mounts put the mounting surface below the axis, so thrust creates an overturning moment . Foot-mounted cylinders must be dowelled or keyed at the cap end so bolts carry no shear.

Pivot mounts — clevis, trunnion, spherical bearing — allow the cylinder to swing with a moving load and must be free to align in the working plane only.

A stop tube is a spacer sleeve on the rod inside the cylinder that prevents the piston from coming closer than a set distance to the rod bearing at full extension. Increasing that separation reduces the bearing load caused by rod sag and side load. Long-stroke cylinders (roughly 40 in and above) require a stop tube to avoid jackknifing and rapid gland wear. Cylinders subject to compressive column loads must also be checked for rod buckling using the manufacturer's stroke-versus-rod-diameter chart based on the mounting style and end conditions.

Cushioning

An end-of-stroke cushion uses a tapered cushion spear or sleeve that enters a matching recess, trapping oil and forcing it out through an adjustable needle valve. A parallel check valve lets oil in freely to restart the stroke. Adjust the cushion needle so the piston decelerates smoothly without bouncing; over-restriction can spike pressure above the relief setting.

Hydraulic Motors

A hydraulic motor is a pump running in reverse: fluid energy in, shaft torque out.

  • Motor type Speed range Torque Notes
  • Gear High (up to ~3,000 RPM) Low Cheap, contamination-tolerant, poor low-speed control
  • Vane Medium Medium Smooth, moderate cost
  • Gerotor / orbital (LSHT) Very low (10–800 RPM) High Low-speed high-torque; conveyor and auger drives, winches

Axial piston Wide, variable High Best efficiency and control; closed-loop transmissions T ( lb-in ) = D ( in 3 / rev ) × Δ P ( psi ) 6.28 T\ (\text{lb-in}) = \frac{D\ (\text{in}^3/\text{rev}) \times \Delta P\ (\text{psi})}{6.28} T ( lb-in ) = 6.28 D ( in 3 / rev ) × Δ P ( psi ) ​ N ( RPM ) = 231 × Q ( GPM ) D ( in 3 / rev ) N\ (\text{RPM}) = \frac{231 \times Q\ (\text{GPM})}{D\ (\text{in}^3/\text{rev})} N ( RPM ) = D ( in 3 / rev ) 231 × Q ( GPM ) ​

Worked example. A 6.0 in³/rev orbital motor drives a conveyor at a 1,800 psi differential, fed 12 GPM. T = 6.0 × 1,800 6.28 = 10,800 6.28 = 1,720 lb-in = 143 lb-ft T = \frac{6.0 \times 1{,}800}{6.28} = \frac{10{,}800}{6.28} = 1{,}720\text{ lb-in} = 143\text{ lb-ft} T = 6.28 6.0 × 1 , 800 ​ = 6.28 10 , 800 ​ = 1 , 720 lb-in = 143 lb-ft N = 231 × 12 6.0 = 2,772 6.0 = 462 RPM N = \frac{231 \times 12}{6.0} = \frac{2{,}772}{6.0} = 462\text{ RPM} N = 6.0 231 × 12 ​ = 6.0 2 , 772 ​ = 462 RPM

Case drain lines on piston and some vane motors must return to tank directly, below oil level, with no restriction and no check valve . Plumbing a case drain into a pressurized return manifold blows the shaft seal out — a very common field failure that the exam likes to test.

Accumulators

An accumulator stores hydraulic energy. It supplies peak flow beyond pump capacity, maintains pressure against leakage, absorbs shock, and provides emergency actuation on power loss.

Type Construction Characteristics

Weight-loaded Dead weight on a vertical ram Constant pressure over the whole stroke; very large, rare, used in central hydraulic plants

Spring-loaded Compression spring on a piston Pressure rises as it fills; small volumes, low pressure

Gas — bladder Nitrogen-filled elastomer bladder in a steel shell Fast response, no piston friction, most common industrial type

Gas — piston Free piston separating nitrogen from oil Large volumes, high pressure ratios, tolerates fast cycling

Gas — diaphragm Welded metal shell with a flexible diaphragm Small volumes; shock suppression on pumps and lines

Pre-Charge Rules

Dry nitrogen only. Never charge with compressed air or oxygen: oxygen compressed against hydrocarbon oil can ignite explosively (dieseling).

Measure pre-charge with the hydraulic side fully discharged to tank , using a charging-and-gauging assembly on the gas valve.

Energy-storage service: pre-charge to roughly 80–90% of minimum system pressure . Too low a pre-charge means the bladder bottoms on the poppet; too high means the bladder slams the shell top and the usable volume collapses.

Shock/pulsation suppression: pre-charge to roughly 60–70% of average working pressure .

Check pre-charge after the first week of service, then at scheduled intervals; nitrogen permeates slowly through a bladder.

Mandatory Safety Rule

An accumulator holds full system pressure after the pump is shut off and locked out. Every hydraulic lockout on an accumulator-equipped machine must include operating the automatic dump / bleed-down valve and verifying zero pressure on the gauge before any line is opened. This connects directly to Task A-1.04 (lock-out/tag-out and zero-energy state) and is one of the most frequently examined safety points in fluid power.