Study guide
12.1 Hydraulic Fundamentals: Pascal’s Law, Pressure, Flow & Power
Red Seal Industrial Mechanic Millwright
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety & Occupational Skills
1.1 WHMIS, SDS & Hazardous Materials 1.2 Lockout/Tagout (LOTO) & Energy Isolation 1.3 Confined Space Entry & Fall Protection 1.4 Blueprint Reading, Trade Math & Precision Measurement Tools 1.5 Hand Tools, Portable Power Tools & Shop Machines 1.6 Access Equipment: Ladders, Scaffolds & Elevating Work Platforms 1.7 Planning Work, Permits, Communication & Mentoring
2 Chapter 2: Fasteners & Bolted Joints
2.1 Threaded Fasteners, Bolts & Thread Standards 2.2 Torque Values, Tightening Patterns & Thread Pitch/Gaging 2.3 Non-Threaded Fasteners, Pins, Keys & Anchors
3 Chapter 3: Rigging, Hoisting & Crane Signals
3.1 Sling Angles, Sling Types & Leg Tension Calculations 3.2 Working Load Limit (WLL) & Hardware Inspection 3.3 Centre of Gravity & Load Weight Estimation 3.4 Hoists, Overhead Cranes & Standard Hand Signals 3.5 Jacking, Skidding, Rollers & Moving Equipment 3.6 Lift Planning, Area Control & Rigging Equipment Maintenance
4 Chapter 4: Prime Movers & Electric Motors
4.1 Electric Motors, Enclosures, Frame Sizes & Synchronous Speed 4.2 Motor Installation, Nameplates & Overload Protection 4.3 Engine Prime Movers & Mechanical Drives Introduction
5 Chapter 5: Belt & Chain Mechanical Drives
5.1 V-Belts, Timing Belts & Sheave Alignment 5.2 Belt Tensioning, Pitch Diameter & Speed Ratios 5.3 Roller Chains, Sprocket Alignment & Lubrication 5.4 Clutches, Brakes & Torque Limiters
6 Chapter 6: Gear Drives, Couplings & Reducers
6.1 Gear Types, Geometry & Gear Ratios 6.2 Couplings (Rigid, Flexible, Fluid) & Installation 6.3 Shaft Keys, Keyways, Taper Sleeves & Hub Fits 6.4 Gear Reducers, Backlash & Mechanical Drive Troubleshooting
7 Chapter 7: Industrial Pumps & Systems
7.1 Centrifugal Pumps, Impellers & Performance Curves 7.2 Positive Displacement Pumps (Gear, Vane, Piston, Diaphragm) 7.3 Cavitation, NPSHa vs NPSHr & Pump Priming 7.4 Pump Maintenance, Packing & Mechanical Seals
8 Chapter 8: Compressors, Fans & Pneumatics
8.1 Reciprocating & Rotary Screw Air Compressors 8.2 Compressed Air Treatment, FRL Units & Air Receivers 8.3 Centrifugal & Axial Fans, Affinity Laws & Airflow 8.4 Pneumatic Circuits, Valves, Actuators & Troubleshooting 8.5 Vacuum Systems, Pumps & Venturi Generators
9 Chapter 9: Bearings, Lubrication & Seals
9.1 Plain Bearings, Bushings & Fits 9.2 Rolling Element Bearings & Installation 9.3 Bearing Heating Limits, Fits & Removal Tools 9.4 Industrial Lubricants, Viscosity, Grease NLGI Grades & Seals
10 Chapter 10: Precision Alignment & Foundations
10.1 Precision Shaft Alignment (Rim-and-Face & Reverse-Dial Methods) 10.2 Laser Alignment, Soft Foot Correction & Thermal Growth 10.3 Machinery Foundations, Leveling, Grouting & Dowelling
11 Chapter 11: Vibration Analysis & Predictive Maintenance
11.1 Vibration Analysis, Dynamic Balancing & Thermography 11.2 Preventive/Predictive Maintenance & Decommissioning 11.3 Non-Destructive Testing (NDT) Methods 11.4 Lubricant & Fluid Analysis 11.5 Commissioning: Pre-Start Checks, Run-In & Documentation
12 Chapter 12: Hydraulic Systems
12.1 Hydraulic Fundamentals: Pascal’s Law, Pressure, Flow & Power 12.2 Hydraulic Fluids, Reservoirs, Filtration & Contamination Control 12.3 Hydraulic Pumps: Gear, Vane & Piston Designs 12.4 Hydraulic Valves: Pressure, Directional & Flow Control 12.5 Hydraulic Actuators: Cylinders, Motors & Accumulators 12.6 Hydraulic Conductors, ISO 1219 Symbols & System Troubleshooting
13 Chapter 13: Conveying Systems, Material Handling & Automation
13.1 Belt Conveyors: Components, Tracking & Training 13.2 Screw, Bucket, Roller, Chain & Pneumatic Conveyors 13.3 Robotics & Automated Equipment
14 Chapter 14: Process Piping, Tanks & Vessels
14.1 Process Piping: Materials, Sizing, Fittings & Joining 14.2 Flanges, Gaskets & Piping Bolted-Joint Assembly 14.3 Tanks, Vessels & Containers: Installation, Inspection & Repair
15 Chapter 15: Materials, Fabrication, Cutting & Welding
15.1 Material Identification: Ferrous & Non-Ferrous Metals, Plastics 15.2 Heat Treatment of Metals 15.3 Oxy-Fuel & Plasma Arc Cutting 15.4 Welding Processes: SMAW, GMAW, GTAW, OFW & Equipment Care 15.5 Layout Procedures & Maintaining Precision Measuring Tools
12.1 Hydraulic Fundamentals: Pascal’s Law, Pressure, Flow & Power
Key Takeaways Explain This Topic AI
Pascal’s law states that pressure applied to a confined fluid is transmitted undiminished and acts with equal force on equal areas in all directions.
A hydraulic pump delivers flow, never pressure; pressure exists only as the fluid meets resistance, so a pump discharging to an open tank reads near zero.
Force equals pressure times area (F = P x A), so a 3 in bore cylinder at 2,000 psi develops 14,137 lbf on extension.
Actuator speed is set by flow rate, not pressure: cylinder velocity (in/min) = 231 x GPM divided by the piston area in square inches.
Hydraulic horsepower = (psi x GPM) / 1714; a 3,000 psi, 10 GPM circuit absorbs about 17.5 hp before pump and motor losses.
Last updated: August 2026
Major Work Activity E — Services fluid power systems carries 21 of the 135 questions on the Interprovincial exam, and Task E-21 (Services hydraulic systems) alone carries 12 questions — the single largest task on the entire exam . Nearly every one of those questions rests on the four relationships covered here. Millwrights install, diagnose, maintain and repair hydraulic power units on presses, injection moulders, mobile equipment, mill gates, log haul-ups, and clamping systems, so the fundamentals must be automatic.
Pascal’s Law and Confined Fluid
Pascal’s law states that pressure applied to a confined fluid at rest is transmitted undiminished in all directions and acts with equal force on equal areas , at right angles to the containing surfaces. Three consequences drive the whole trade:
A small input force acting on a small area can generate a very large output force on a large area — hydraulic force multiplication .
Pressure is uniform throughout a static connected circuit, so a gauge anywhere downstream of the pump (with no restriction between) reads the same value.
Liquids are effectively incompressible (mineral oil compresses roughly 0.5% per 1,000 psi), so motion transfers almost instantly — unlike air, which stores energy by compressing.
Pressure Definition and Units
Pressure is force per unit area. Canadian shops work in both systems, and the exam uses both:
- Unit Symbol Equivalence
- Pounds per square inch psi 1 psi = 6.895 kPa
- Kilopascal kPa 1,000 kPa = 1 MPa = 145 psi
- Bar bar 1 bar = 100 kPa = 14.5 psi
- Atmosphere (sea level) atm 1 atm = 14.7 psia = 101.3 kPa
Gauge pressure (psig) reads zero at atmosphere; absolute pressure (psia) adds the 14.7 psi atmospheric column. Pump inlet (suction) calculations must use absolute pressure, because a pump inlet can only ever pull down toward a vacuum — atmospheric pressure is what actually pushes fluid into the pump.
Pumps Make Flow — Resistance Makes Pressure
This is the single most-tested concept in hydraulics, and the most common apprentice misconception.
A hydraulic pump is a flow generator . It moves a fixed volume of oil per revolution from inlet to outlet. If that outlet were piped straight back to an open reservoir, the gauge would read only the few psi needed to push oil through the return line. Pressure is generated by resistance to flow — a load on a cylinder, an orifice, a closed valve, or a relief valve setting. PUMP OUTPUT = FLOW (GPM / L/min) RESISTANCE = PRESSURE (psi / kPa)
- +--------+ Q +--------------+ Load 20,000 lb
- | PUMP |----------->| CYLINDER |=========[]============
- +--------+ +--------------+
- | ^
- | Relief valve | Pressure rises only until the
- +--> set 3,000 psi | load moves, or the relief opens
Practical consequences a millwright is expected to state:
A machine that will not build pressure is usually leaking flow internally (worn pump, bypassing cylinder seal, relief valve stuck open), not "short of pressure."
A machine that builds full pressure but moves slowly has lost flow (worn pump, restricted filter, partly closed flow control), not force.
Loss of force points to pressure; loss of speed points to flow. Memorize that pairing — it decides many exam troubleshooting questions.
Force, Area and Mechanical Advantage F = P × A F = P \times A F = P × A
For a round cylinder bore, area is: A = π D 2 4 = 0.7854 D 2 A = \frac{\pi D^2}{4} = 0.7854 D^2 A = 4 π D 2 = 0.7854 D 2
Worked example — extension force. A cylinder with a 3.0 in bore is fed 2,000 psi. A = 0.7854 × 3.0 2 = 7.069 in 2 A = 0.7854 \times 3.0^2 = 7.069\text{ in}^2 A = 0.7854 × 3. 0 2 = 7.069 in 2 F = 2,000 × 7.069 = 14,137 lbf F = 2{,}000 \times 7.069 = 14{,}137\text{ lbf} F = 2 , 000 × 7.069 = 14 , 137 lbf
Worked example — retraction force. The same cylinder has a 1.5 in rod. On retraction, oil acts on the annulus (bore area minus rod area): A ann = 0.7854 × ( 3.0 2 − 1.5 2 ) = 0.7854 × 6.75 = 5.301 in 2 A_{\text{ann}} = 0.7854 \times (3.0^2 - 1.5^2) = 0.7854 \times 6.75 = 5.301\text{ in}^2 A ann = 0.7854 × ( 3. 0 2 − 1. 5 2 ) = 0.7854 × 6.75 = 5.301 in 2 F = 2,000 × 5.301 = 10,603 lbf F = 2{,}000 \times 5.301 = 10{,}603\text{ lbf} F = 2 , 000 × 5.301 = 10 , 603 lbf
A standard differential cylinder therefore always pushes harder than it pulls, and always retracts faster than it extends at the same flow rate. Presses, balers and clamps are oriented so the working stroke is the extend stroke.
Flow, Velocity and Actuator Speed
Flow rate (Q) is volume per unit time — GPM (US gallons per minute) or L/min. One US gallon equals 231 cubic inches , a conversion the exam expects you to use unprompted.
Cylinder speed: v ( in/min ) = 231 × GPM A ( in 2 ) v\ (\text{in/min}) = \frac{231 \times \text{GPM}}{A\ (\text{in}^2)} v ( in/min ) = A ( in 2 ) 231 × GPM
Worked example. Feeding the 3.0 in bore cylinder above with 8 GPM: v = 231 × 8 7.069 = 1,848 7.069 = 261.4 in/min ≈ 21.8 ft/min v = \frac{231 \times 8}{7.069} = \frac{1{,}848}{7.069} = 261.4\text{ in/min} \approx 21.8\text{ ft/min} v = 7.069 231 × 8 = 7.069 1 , 848 = 261.4 in/min ≈ 21.8 ft/min
Retracting the same cylinder with the same 8 GPM on the 5.301 in² annulus gives 348.6 in/min — about 1.33 times faster, exactly the inverse of the force ratio. Energy is conserved: what you gain in speed you lose in force.
Fluid Velocity in Conductors
Line sizing controls turbulence, heat and noise. Accepted industrial design velocities:
- Line Recommended velocity Reason
- Pump suction / inlet 2–4 ft/s (0.6–1.2 m/s) Prevents inlet starvation and pump cavitation
- Return line 10–15 ft/s (3–4.5 m/s) Low back-pressure, allows filter and cooler
- Pressure line 15–20 ft/s (4.5–6 m/s) Balances line size against friction heat
Undersized suction line is the classic root cause of pump cavitation and its distinctive high-pitched rattling noise.
Hydraulic Power Hydraulic HP = P ( psi ) × Q ( GPM ) 1714 \text{Hydraulic HP} = \frac{P\ (\text{psi}) \times Q\ (\text{GPM})}{1714} Hydraulic HP = 1714 P ( psi ) × Q ( GPM ) Hydraulic kW = P ( bar ) × Q ( L/min ) 600 \text{Hydraulic kW} = \frac{P\ (\text{bar}) \times Q\ (\text{L/min})}{600} Hydraulic kW = 600 P ( bar ) × Q ( L/min )
Worked example — motor sizing. A power unit runs 10 GPM at 3,000 psi. HHP = 3,000 × 10 1714 = 17.5 hp \text{HHP} = \frac{3{,}000 \times 10}{1714} = 17.5\text{ hp} HHP = 1714 3 , 000 × 10 = 17.5 hp
At a combined pump and drive efficiency of about 85%, the electric motor must deliver roughly 20.6 hp, so a 25 hp motor is selected. Every hydraulic horsepower that does not do useful work becomes heat : 1 hp = 2,545 BTU/hr. A relief valve dumping 10 GPM at 3,000 psi continuously adds about 44,500 BTU/hr to the reservoir — which is why a machine left deadheaded on relief overheats within minutes.
Exam Traps
Pressure gauge reads zero, motor runs. The pump may be fine — look for an unloaded circuit, an open-centre valve, or a relief valve stuck open.
Hydraulic oil is not a coolant. Any pressure drop across a valve, orifice or relief converts directly to heat in the tank.
Do not confuse head with pressure : 1 psi lifts water 2.31 ft, but oil at 0.87 specific gravity gives 2.65 ft per psi.