Study guide
14.2 Flanges, Gaskets & Piping Bolted-Joint Assembly
Red Seal Industrial Mechanic Millwright
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety & Occupational Skills
1.1 WHMIS, SDS & Hazardous Materials 1.2 Lockout/Tagout (LOTO) & Energy Isolation 1.3 Confined Space Entry & Fall Protection 1.4 Blueprint Reading, Trade Math & Precision Measurement Tools 1.5 Hand Tools, Portable Power Tools & Shop Machines 1.6 Access Equipment: Ladders, Scaffolds & Elevating Work Platforms 1.7 Planning Work, Permits, Communication & Mentoring
2 Chapter 2: Fasteners & Bolted Joints
2.1 Threaded Fasteners, Bolts & Thread Standards 2.2 Torque Values, Tightening Patterns & Thread Pitch/Gaging 2.3 Non-Threaded Fasteners, Pins, Keys & Anchors
3 Chapter 3: Rigging, Hoisting & Crane Signals
3.1 Sling Angles, Sling Types & Leg Tension Calculations 3.2 Working Load Limit (WLL) & Hardware Inspection 3.3 Centre of Gravity & Load Weight Estimation 3.4 Hoists, Overhead Cranes & Standard Hand Signals 3.5 Jacking, Skidding, Rollers & Moving Equipment 3.6 Lift Planning, Area Control & Rigging Equipment Maintenance
4 Chapter 4: Prime Movers & Electric Motors
4.1 Electric Motors, Enclosures, Frame Sizes & Synchronous Speed 4.2 Motor Installation, Nameplates & Overload Protection 4.3 Engine Prime Movers & Mechanical Drives Introduction
5 Chapter 5: Belt & Chain Mechanical Drives
5.1 V-Belts, Timing Belts & Sheave Alignment 5.2 Belt Tensioning, Pitch Diameter & Speed Ratios 5.3 Roller Chains, Sprocket Alignment & Lubrication 5.4 Clutches, Brakes & Torque Limiters
6 Chapter 6: Gear Drives, Couplings & Reducers
6.1 Gear Types, Geometry & Gear Ratios 6.2 Couplings (Rigid, Flexible, Fluid) & Installation 6.3 Shaft Keys, Keyways, Taper Sleeves & Hub Fits 6.4 Gear Reducers, Backlash & Mechanical Drive Troubleshooting
7 Chapter 7: Industrial Pumps & Systems
7.1 Centrifugal Pumps, Impellers & Performance Curves 7.2 Positive Displacement Pumps (Gear, Vane, Piston, Diaphragm) 7.3 Cavitation, NPSHa vs NPSHr & Pump Priming 7.4 Pump Maintenance, Packing & Mechanical Seals
8 Chapter 8: Compressors, Fans & Pneumatics
8.1 Reciprocating & Rotary Screw Air Compressors 8.2 Compressed Air Treatment, FRL Units & Air Receivers 8.3 Centrifugal & Axial Fans, Affinity Laws & Airflow 8.4 Pneumatic Circuits, Valves, Actuators & Troubleshooting 8.5 Vacuum Systems, Pumps & Venturi Generators
9 Chapter 9: Bearings, Lubrication & Seals
9.1 Plain Bearings, Bushings & Fits 9.2 Rolling Element Bearings & Installation 9.3 Bearing Heating Limits, Fits & Removal Tools 9.4 Industrial Lubricants, Viscosity, Grease NLGI Grades & Seals
10 Chapter 10: Precision Alignment & Foundations
10.1 Precision Shaft Alignment (Rim-and-Face & Reverse-Dial Methods) 10.2 Laser Alignment, Soft Foot Correction & Thermal Growth 10.3 Machinery Foundations, Leveling, Grouting & Dowelling
11 Chapter 11: Vibration Analysis & Predictive Maintenance
11.1 Vibration Analysis, Dynamic Balancing & Thermography 11.2 Preventive/Predictive Maintenance & Decommissioning 11.3 Non-Destructive Testing (NDT) Methods 11.4 Lubricant & Fluid Analysis 11.5 Commissioning: Pre-Start Checks, Run-In & Documentation
12 Chapter 12: Hydraulic Systems
12.1 Hydraulic Fundamentals: Pascal’s Law, Pressure, Flow & Power 12.2 Hydraulic Fluids, Reservoirs, Filtration & Contamination Control 12.3 Hydraulic Pumps: Gear, Vane & Piston Designs 12.4 Hydraulic Valves: Pressure, Directional & Flow Control 12.5 Hydraulic Actuators: Cylinders, Motors & Accumulators 12.6 Hydraulic Conductors, ISO 1219 Symbols & System Troubleshooting
13 Chapter 13: Conveying Systems, Material Handling & Automation
13.1 Belt Conveyors: Components, Tracking & Training 13.2 Screw, Bucket, Roller, Chain & Pneumatic Conveyors 13.3 Robotics & Automated Equipment
14 Chapter 14: Process Piping, Tanks & Vessels
14.1 Process Piping: Materials, Sizing, Fittings & Joining 14.2 Flanges, Gaskets & Piping Bolted-Joint Assembly 14.3 Tanks, Vessels & Containers: Installation, Inspection & Repair
15 Chapter 15: Materials, Fabrication, Cutting & Welding
15.1 Material Identification: Ferrous & Non-Ferrous Metals, Plastics 15.2 Heat Treatment of Metals 15.3 Oxy-Fuel & Plasma Arc Cutting 15.4 Welding Processes: SMAW, GMAW, GTAW, OFW & Equipment Care 15.5 Layout Procedures & Maintaining Precision Measuring Tools
14.2 Flanges, Gaskets & Piping Bolted-Joint Assembly
Key Takeaways Explain This Topic AI
ASME B16.5 flange pressure classes (150, 300, 600, 900, 1500, 2500) state a pressure-temperature rating, not a fixed pressure — the allowable pressure falls as temperature rises.
A raised-face steel flange must never be bolted directly to a flat-face cast iron flange, because the raised face acts as a fulcrum and cracks the brittle casting.
Spiral-wound gaskets require both an inner ring and an outer centring ring on raised-face flanges to prevent inward buckling and to centre the gasket.
ASME PCC-1 bolt-up practice uses a numbered cross pattern in four passes — snug, 30%, 60% and 100% of target torque — followed by at least one rotational round pass.
Flange alignment must be corrected before bolting: rotational misalignment of bolt holes and gaps between faces must never be pulled closed with the flange bolts.
Last updated: August 2026
Sub-tasks D-19.02/.06/.08 and A-3.05 (Uses fastening and retaining devices) meet at the flanged joint. A leaking flange is the most common piping call-out a millwright receives, and almost all of those leaks come from assembly errors rather than gasket defects.
Flange Types
Type Construction Use
Weld neck Long tapered hub butt-welded to the pipe Highest integrity; high pressure, cyclic and high-temperature service
- Slip-on Slides over the pipe, filleted inside and out Lower cost, easier fit-up; lower fatigue strength
- Socket weld Pipe bottoms in a socket, single external fillet Small bore, NPS 2 and under
- Lap joint Loose backing flange over a stub end Frequent dismantling, expensive alloys (only the stub is alloy)
- Threaded Screwed onto NPT pipe Low pressure, no welding permitted areas
- Blind Solid disc Positive isolation and vessel closures
- Flange Faces
Face Description Gasket
Raised face (RF) Gasket surface raised roughly 1.6 mm (Class 150/300) above the bolt circle Ring gasket inside the bolt circle
Flat face (FF) Full flat surface Full-face gasket covering the bolt circle
Ring type joint (RTJ) Machined groove for a metal ring Oval or octagonal soft-iron/stainless ring; very high pressure
The critical compatibility rule: never bolt a raised-face steel flange to a flat-face cast iron flange . The raised face bears only on the centre of the brittle casting and acts as a fulcrum, so tightening the bolts bends and cracks the cast flange. The correct practice is to machine the steel flange to flat face and use a full-face gasket , which spreads the load out to the bolt circle.
The gasket surface finish matters too. Standard raised faces are serrated (a concentric or spiral phonographic groove, typically 125–250 micro-inch Ra) to bite into a soft gasket. Facing a flange smooth for a soft gasket invites blow-out.
Pressure Classes
ASME B16.5 classes — 150, 300, 600, 900, 1500 and 2500 — are pressure-temperature ratings , not fixed pressures. A Class 150 carbon steel flange is rated near 285 psig at ambient but only about 150 psig at 260 C and less as temperature climbs further. Class number is not the working pressure. Matching flange class, bolting material and gasket to the actual service pressure and temperature is a design requirement, not a field improvisation.
Gasket Selection
Gasket Construction Service
Compressed non-asbestos sheet Aramid or glass fibre with elastomer binder General water, air, low-pressure process
PTFE (virgin or expanded) Chemically inert fluoropolymer Aggressive chemicals; expanded PTFE conforms to damaged faces
Graphite (flexible) Exfoliated graphite, often with a metal insert High temperature, steam
Spiral wound Alternating V-shaped metal strip and filler wound in a spiral The industrial standard for steam, hydrocarbons and higher pressures
Ring joint (RTJ) Solid metal oval or octagonal ring Very high pressure and temperature; wellheads, high-pressure headers
Metal jacketed Soft filler in a metal envelope Heat exchangers
A spiral-wound gasket on a raised face requires two rings:
The outer centring ring locates the gasket concentric to the bore and acts as a compression stop so the winding is not crushed.
The inner ring prevents the winding from buckling inward into the pipe bore under pressure, and is mandatory for PTFE-filled gaskets and for high-pressure and vacuum service.
Colour coding on the outer ring edge identifies the winding metal, and a stripe identifies the filler material — worth knowing when verifying that the right gasket is being installed.
Never reuse a gasket , and never stack two gaskets to close a gap. Never apply thread sealant or "goop" to a gasket face on a properly finished flange.
Flange Alignment Before Bolting
The joint must fit before any bolt is loaded. Common acceptance criteria used in industry (verify against the project specification):
Condition Typical tolerance
Parallelism (gap variation across the face) Within about 0.8 mm (1/32 in) measured at four points 90 degrees apart
- Centreline offset (concentricity) Within about 1.5 mm (1/16 in)
- Rotational bolt-hole alignment Bolts must pass freely by hand through both flanges
- Face-to-face gap Gasket thickness plus a small tolerance; must not require bolt pull
Never use the flange bolts as a come-along. Pulling misaligned flanges together with the studs preloads the joint permanently, transfers that force straight into the connected pump, compressor or vessel nozzle, cocks the gasket, and guarantees an eventual leak. Correct the pipe support, the spool length or the hanger instead.
Standard flange practice is to orient bolt holes straddling the vertical and horizontal centrelines ("two-holing"), so no bolt sits at top dead centre and gauge or drain connections stay clear.
Bolt-Up: The ASME PCC-1 Method
ASME PCC-1 (Guidelines for Pressure Boundary Bolted Flange Joint Assembly) is the accepted reference. The objective is uniform gasket stress, not maximum torque.
Inspect and clean. Wire-brush the flange faces, check for radial scratches across the seating surface, and confirm both faces and the gasket are clean, dry and undamaged.
Use new bolting where specified, and lubricate the stud threads and nut bearing faces with the specified compound. Torque values assume a stated nut factor; an unlubricated stud may reach only 40–60% of the intended preload for the same torque.
Number the bolts around the flange (1, 2, 3 ... clockwise) so the pattern can be followed and recorded.
Fit the gasket dry and centred. Do not use adhesive or grease to hold it.
Hand-tighten and check gap at four points before applying torque.
Apply torque in a criss-cross (star) pattern in stages:
- Pass 1 — snug, roughly 20–30% of target
- Pass 2 — about 50–70% of target
- Pass 3 — 100% of target
- Pass 4 — a rotational (clockwise) round pass at 100%, continuing until no nut turns further
Re-check after 4 hours or after the first thermal cycle where the specification calls for it, because gaskets relax (short-term creep) and bolts lose preload. 8-BOLT FLANGE CROSS-PATTERN SEQUENCE
- 1
- 7 4
6 5 tightening order:
- 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8
- 3 8 (each bolt roughly opposite
- 2 the previous one)
For large-diameter and high-class flanges, hydraulic torque wrenches or hydraulic bolt tensioners are used to achieve accurate, repeatable preload; tensioners stretch the stud directly and avoid friction scatter entirely.
Leak Diagnosis on a Flanged Joint
Symptom Likely cause
Leak at one segment of the circumference Uneven bolt load, a flange out of parallel, or a damaged face at that point
- Leak appearing after the first heat-up Gasket relaxation — the joint needed a hot re-torque
- Gasket blown out radially Under-bolted, wrong gasket class, or spiral-wound installed without an inner ring
- Gasket crushed and extruded Over-torqued, wrong gasket for the class, or missing outer centring ring
- Repeat failures on the same joint Pipe strain forcing the joint — investigate supports, not the gasket