Study guide
14.1 Process Piping: Materials, Sizing, Fittings & Joining
Red Seal Industrial Mechanic Millwright
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety & Occupational Skills
1.1 WHMIS, SDS & Hazardous Materials 1.2 Lockout/Tagout (LOTO) & Energy Isolation 1.3 Confined Space Entry & Fall Protection 1.4 Blueprint Reading, Trade Math & Precision Measurement Tools 1.5 Hand Tools, Portable Power Tools & Shop Machines 1.6 Access Equipment: Ladders, Scaffolds & Elevating Work Platforms 1.7 Planning Work, Permits, Communication & Mentoring
2 Chapter 2: Fasteners & Bolted Joints
2.1 Threaded Fasteners, Bolts & Thread Standards 2.2 Torque Values, Tightening Patterns & Thread Pitch/Gaging 2.3 Non-Threaded Fasteners, Pins, Keys & Anchors
3 Chapter 3: Rigging, Hoisting & Crane Signals
3.1 Sling Angles, Sling Types & Leg Tension Calculations 3.2 Working Load Limit (WLL) & Hardware Inspection 3.3 Centre of Gravity & Load Weight Estimation 3.4 Hoists, Overhead Cranes & Standard Hand Signals 3.5 Jacking, Skidding, Rollers & Moving Equipment 3.6 Lift Planning, Area Control & Rigging Equipment Maintenance
4 Chapter 4: Prime Movers & Electric Motors
4.1 Electric Motors, Enclosures, Frame Sizes & Synchronous Speed 4.2 Motor Installation, Nameplates & Overload Protection 4.3 Engine Prime Movers & Mechanical Drives Introduction
5 Chapter 5: Belt & Chain Mechanical Drives
5.1 V-Belts, Timing Belts & Sheave Alignment 5.2 Belt Tensioning, Pitch Diameter & Speed Ratios 5.3 Roller Chains, Sprocket Alignment & Lubrication 5.4 Clutches, Brakes & Torque Limiters
6 Chapter 6: Gear Drives, Couplings & Reducers
6.1 Gear Types, Geometry & Gear Ratios 6.2 Couplings (Rigid, Flexible, Fluid) & Installation 6.3 Shaft Keys, Keyways, Taper Sleeves & Hub Fits 6.4 Gear Reducers, Backlash & Mechanical Drive Troubleshooting
7 Chapter 7: Industrial Pumps & Systems
7.1 Centrifugal Pumps, Impellers & Performance Curves 7.2 Positive Displacement Pumps (Gear, Vane, Piston, Diaphragm) 7.3 Cavitation, NPSHa vs NPSHr & Pump Priming 7.4 Pump Maintenance, Packing & Mechanical Seals
8 Chapter 8: Compressors, Fans & Pneumatics
8.1 Reciprocating & Rotary Screw Air Compressors 8.2 Compressed Air Treatment, FRL Units & Air Receivers 8.3 Centrifugal & Axial Fans, Affinity Laws & Airflow 8.4 Pneumatic Circuits, Valves, Actuators & Troubleshooting 8.5 Vacuum Systems, Pumps & Venturi Generators
9 Chapter 9: Bearings, Lubrication & Seals
9.1 Plain Bearings, Bushings & Fits 9.2 Rolling Element Bearings & Installation 9.3 Bearing Heating Limits, Fits & Removal Tools 9.4 Industrial Lubricants, Viscosity, Grease NLGI Grades & Seals
10 Chapter 10: Precision Alignment & Foundations
10.1 Precision Shaft Alignment (Rim-and-Face & Reverse-Dial Methods) 10.2 Laser Alignment, Soft Foot Correction & Thermal Growth 10.3 Machinery Foundations, Leveling, Grouting & Dowelling
11 Chapter 11: Vibration Analysis & Predictive Maintenance
11.1 Vibration Analysis, Dynamic Balancing & Thermography 11.2 Preventive/Predictive Maintenance & Decommissioning 11.3 Non-Destructive Testing (NDT) Methods 11.4 Lubricant & Fluid Analysis 11.5 Commissioning: Pre-Start Checks, Run-In & Documentation
12 Chapter 12: Hydraulic Systems
12.1 Hydraulic Fundamentals: Pascal’s Law, Pressure, Flow & Power 12.2 Hydraulic Fluids, Reservoirs, Filtration & Contamination Control 12.3 Hydraulic Pumps: Gear, Vane & Piston Designs 12.4 Hydraulic Valves: Pressure, Directional & Flow Control 12.5 Hydraulic Actuators: Cylinders, Motors & Accumulators 12.6 Hydraulic Conductors, ISO 1219 Symbols & System Troubleshooting
13 Chapter 13: Conveying Systems, Material Handling & Automation
13.1 Belt Conveyors: Components, Tracking & Training 13.2 Screw, Bucket, Roller, Chain & Pneumatic Conveyors 13.3 Robotics & Automated Equipment
14 Chapter 14: Process Piping, Tanks & Vessels
14.1 Process Piping: Materials, Sizing, Fittings & Joining 14.2 Flanges, Gaskets & Piping Bolted-Joint Assembly 14.3 Tanks, Vessels & Containers: Installation, Inspection & Repair
15 Chapter 15: Materials, Fabrication, Cutting & Welding
15.1 Material Identification: Ferrous & Non-Ferrous Metals, Plastics 15.2 Heat Treatment of Metals 15.3 Oxy-Fuel & Plasma Arc Cutting 15.4 Welding Processes: SMAW, GMAW, GTAW, OFW & Equipment Care 15.5 Layout Procedures & Maintaining Precision Measuring Tools
14.1 Process Piping: Materials, Sizing, Fittings & Joining
Key Takeaways Explain This Topic AI
Pipe is specified by Nominal Pipe Size and schedule: the outside diameter is fixed for a given NPS, and a higher schedule adds wall thickness inward, reducing the bore.
Process piping in Canada is designed and installed to ASME B31.3, with pressure-retaining fabrication registered through provincial authorities under CSA B51.
An eccentric reducer on a pump suction line is installed flat side up so no air pocket can form ahead of the pump inlet.
Gate, ball, plug and butterfly valves are isolation devices, while globe and needle valves are the correct choice for throttling service.
Thermal growth of a straight run is calculated as change in length equals coefficient times length times temperature change; a 30 m carbon steel line heated 100 C grows about 35 mm and must be accommodated by loops or expansion joints.
Last updated: August 2026
Task D-19 (Services process piping, tanks and containers) carries 4 exam questions across eight sub-tasks — install, diagnose, maintain and repair, for both piping and vessels. Millwrights routinely install pump suction and discharge piping, lubrication and cooling lines, compressed air mains and process headers.
Pipe Sizing: NPS and Schedule
Nominal Pipe Size (NPS) is a dimensionless designator, not a measurement. For a given NPS, the outside diameter is fixed , and the schedule number sets the wall thickness. Increasing the schedule thickens the wall inward , shrinking the bore while the OD stays the same — this is what makes standard fittings work across schedules.
- NPS Outside diameter Sch 40 wall Sch 40 ID Sch 80 wall Sch 80 ID
- 2 in 2.375 in 0.154 in 2.067 in 0.218 in 1.939 in
- 4 in 4.500 in 0.237 in 4.026 in 0.337 in 3.826 in
- 6 in 6.625 in 0.280 in 6.065 in 0.432 in 5.761 in
At and above NPS 14 the designator equals the actual OD in inches. Note that at NPS 2 and below, the nominal size is neither the OD nor the ID — a common source of ordering errors.
Tubing is entirely different: tube is specified by actual outside diameter and wall thickness (or by BWG/gauge). A 1/2 in tube measures 0.500 in OD; a 1/2 in pipe measures 0.840 in OD.
Materials
Material Common specification Service
Carbon steel ASTM A53 (welded/seamless), A106 (seamless, high temperature) General process, steam, compressed air, oil
Stainless steel 304/304L, 316/316L Corrosive service, food and pharmaceutical, chloride-bearing streams favour 316
- Copper Type K (thickest), L, M (thinnest) Instrument air, potable water, refrigeration (Type ACR)
- PVC / CPVC Sch 40 / Sch 80 Cold chemical and water service; CPVC to about 90 C. Never for compressed air
- HDPE Rated by DR (dimension ratio) Buried water, slurry, effluent; heat-fusion joined
- Ductile iron Class-rated Large water mains, fire protection
Never use PVC for compressed gas. PVC fails by brittle shatter, propelling fragments; compressed air stores enough energy to make that failure lethal. This is a routinely examined safety rule.
Codes and Jurisdiction
ASME B31.3 (Process Piping) governs design, materials, fabrication, examination and testing of process piping.
ASME B31.1 (Power Piping) governs boiler external piping and power plant service.
CSA B51 is the Canadian code for boilers, pressure vessels and pressure piping. Pressure-retaining designs are registered with a Canadian Registration Number (CRN) , and welding is performed by shops qualified under CSA W47.1 to CSA W59 procedures.
Enforcement is provincial : TSSA in Ontario, ABSA in Alberta, Technical Safety BC, and equivalent authorities elsewhere. A millwright must know that pressure-retaining welds require a qualified welder and procedure, and are not general shop work.
Fittings
Fitting Purpose Notes
90 / 45 degree elbow Direction change Long radius (1.5 x NPS) is standard; short radius only where space forces it and pressure drop allows
- Tee (equal / reducing) Branch connection Reducing tee saves a separate reducer
- Concentric reducer Size change on a common centreline Vertical lines and discharge piping
Eccentric reducer Size change with one flat side Pump suction: flat side up , so no air pocket collects at the pump inlet
- Union Breakable joint in threaded pipe Place near equipment for removal
- Coupling / half coupling Straight joint, branch outlet Threadolet/weldolet for branch takeoffs
Cap / plug / blind flange Termination or isolation A blind flange is the positive isolation for line-breaking work
Joining Methods
Method Pressure capability Application and cautions
Threaded (NPT) Low to medium, small bore Fast; use approved sealant or PTFE tape wrapped in the thread direction; not for high vibration or critical service
Socket weld High, NPS 2 and under Requires a 1.5 mm expansion gap at the socket bottom before welding, or thermal stress cracks the weld
Butt weld Highest Full-penetration weld, smooth bore, best for critical and high-temperature service; requires bevelled ends and fit-up alignment
Flanged High Breakable for maintenance; see section 14.2
Grooved coupling Medium Roll- or cut-grooved ends with a housing and gasket; fast, allows minor deflection, common in fire and HVAC service
- Solvent weld Low PVC/CPVC; requires primer, correct cement, and full cure time before pressurizing
- Heat fusion Medium HDPE butt or electrofusion; produces a joint as strong as the pipe
Compression / flare Low to medium, tubing Instrument and lube lines; ferrule must not be reused on a new tube end
Valves: Isolation versus Throttling
- Valve Function Key point
- Gate Isolation only Full bore, low pressure drop; throttling erodes the seat and causes chatter
- Ball Quarter-turn isolation Fast, tight shutoff; standard ball valves also should not throttle
Butterfly Isolation, coarse control Compact and cheap in large sizes; disc obstructs flow slightly even when open
- Plug Isolation Lubricated or sleeved; handles slurries
- Globe Throttling Flow changes direction through a seat and disc; higher pressure drop but excellent control
- Needle Fine throttling Small bore, instrument and metering service
Check Prevents reverse flow Swing, lift, wafer/dual-plate, and silent (spring-assisted) types; orientation and flow arrow are critical
Diaphragm / pinch Isolation and control of slurries No cavity to trap solids
Stem style matters for clearance and diagnostics: a rising stem shows valve position visually and needs headroom; a non-rising stem fits confined spaces but gives no visual indication.
Thermal Expansion and Pipe Supports
Piping grows when it heats. Ignoring that growth breaks nozzles off pumps and vessels — a mechanical failure the millwright is called to repair. Δ L = α × L × Δ T \Delta L = \alpha \times L \times \Delta T Δ L = α × L × Δ T
Worked example. A 30 m carbon steel steam condensate line (alpha = 11.7 x 10⁻⁶ mm/mm/C) is installed at 20 C and operates at 120 C. Δ L = ( 11.7 × 10 − 6 ) × 30,000 mm × 100 = 35.1 mm \Delta L = (11.7 \times 10^{-6}) \times 30{,}000\text{ mm} \times 100 = 35.1\text{ mm} Δ L = ( 11.7 × 1 0 − 6 ) × 30 , 000 mm × 100 = 35.1 mm
That 35 mm has to go somewhere. Accommodation methods:
Expansion loop — a U-shaped offset that flexes; the simplest and most reliable, needs space.
Bellows expansion joint — a metal bellows that compresses axially; must be installed with the shipping bars removed only after the anchors and guides are complete , or it will squirm and fail.
Slip joint — a packed telescoping joint; requires periodic packing service.
Offsets and changes of direction — natural flexibility in a routed system.
Support hardware:
- Support Function
- Anchor Rigid restraint; establishes the fixed point from which growth is directed
- Guide Allows axial movement, prevents lateral movement and buckling
- Rigid hanger / rod Carries weight where no vertical movement occurs
- Spring hanger (variable) Carries weight while allowing vertical thermal movement; load varies with travel
- Constant-support hanger Maintains constant load through the full travel; used at sensitive equipment nozzles
- Roller / slide support Lets a horizontal run move axially over a support
Pipe strain on rotating equipment is a classic millwright failure mode. Piping must be supported so that it comes to the pump or compressor flange free and in alignment , with no need to pull the flanges together. The standard check is to set a dial indicator on the pump shaft, loosen the suction and discharge flange bolts, and watch for shaft movement. Movement greater than about 0.05 mm (0.002 in) means the piping is forcing the casing, which will distort the housing, destroy the alignment, and wreck the bearings and seals. Correct the piping — never shim the pump to chase a pipe-strain misalignment.
Line Breaking and Isolation
Opening a process line is a controlled activity governed by A-1.04 zero-energy principles:
Identify the contents and hazards from the P&ID and the SDS.
Isolate with double block and bleed where the service is hazardous, or install a blind/spade for positive isolation.
Drain, vent, flush and purge; verify with a gauge that pressure is zero.
Lock out and tag every isolation point, including the drivers of any pump that can repressurize the line.
Wear PPE for the contents, and crack the flange on the far side from your body, breaking the joint at the bottom last so residual liquid drains away from you.