Study guide
3.5 Jacking, Skidding, Rollers & Moving Equipment
Red Seal Industrial Mechanic Millwright
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety & Occupational Skills
1.1 WHMIS, SDS & Hazardous Materials 1.2 Lockout/Tagout (LOTO) & Energy Isolation 1.3 Confined Space Entry & Fall Protection 1.4 Blueprint Reading, Trade Math & Precision Measurement Tools 1.5 Hand Tools, Portable Power Tools & Shop Machines 1.6 Access Equipment: Ladders, Scaffolds & Elevating Work Platforms 1.7 Planning Work, Permits, Communication & Mentoring
2 Chapter 2: Fasteners & Bolted Joints
2.1 Threaded Fasteners, Bolts & Thread Standards 2.2 Torque Values, Tightening Patterns & Thread Pitch/Gaging 2.3 Non-Threaded Fasteners, Pins, Keys & Anchors
3 Chapter 3: Rigging, Hoisting & Crane Signals
3.1 Sling Angles, Sling Types & Leg Tension Calculations 3.2 Working Load Limit (WLL) & Hardware Inspection 3.3 Centre of Gravity & Load Weight Estimation 3.4 Hoists, Overhead Cranes & Standard Hand Signals 3.5 Jacking, Skidding, Rollers & Moving Equipment 3.6 Lift Planning, Area Control & Rigging Equipment Maintenance
4 Chapter 4: Prime Movers & Electric Motors
4.1 Electric Motors, Enclosures, Frame Sizes & Synchronous Speed 4.2 Motor Installation, Nameplates & Overload Protection 4.3 Engine Prime Movers & Mechanical Drives Introduction
5 Chapter 5: Belt & Chain Mechanical Drives
5.1 V-Belts, Timing Belts & Sheave Alignment 5.2 Belt Tensioning, Pitch Diameter & Speed Ratios 5.3 Roller Chains, Sprocket Alignment & Lubrication 5.4 Clutches, Brakes & Torque Limiters
6 Chapter 6: Gear Drives, Couplings & Reducers
6.1 Gear Types, Geometry & Gear Ratios 6.2 Couplings (Rigid, Flexible, Fluid) & Installation 6.3 Shaft Keys, Keyways, Taper Sleeves & Hub Fits 6.4 Gear Reducers, Backlash & Mechanical Drive Troubleshooting
7 Chapter 7: Industrial Pumps & Systems
7.1 Centrifugal Pumps, Impellers & Performance Curves 7.2 Positive Displacement Pumps (Gear, Vane, Piston, Diaphragm) 7.3 Cavitation, NPSHa vs NPSHr & Pump Priming 7.4 Pump Maintenance, Packing & Mechanical Seals
8 Chapter 8: Compressors, Fans & Pneumatics
8.1 Reciprocating & Rotary Screw Air Compressors 8.2 Compressed Air Treatment, FRL Units & Air Receivers 8.3 Centrifugal & Axial Fans, Affinity Laws & Airflow 8.4 Pneumatic Circuits, Valves, Actuators & Troubleshooting 8.5 Vacuum Systems, Pumps & Venturi Generators
9 Chapter 9: Bearings, Lubrication & Seals
9.1 Plain Bearings, Bushings & Fits 9.2 Rolling Element Bearings & Installation 9.3 Bearing Heating Limits, Fits & Removal Tools 9.4 Industrial Lubricants, Viscosity, Grease NLGI Grades & Seals
10 Chapter 10: Precision Alignment & Foundations
10.1 Precision Shaft Alignment (Rim-and-Face & Reverse-Dial Methods) 10.2 Laser Alignment, Soft Foot Correction & Thermal Growth 10.3 Machinery Foundations, Leveling, Grouting & Dowelling
11 Chapter 11: Vibration Analysis & Predictive Maintenance
11.1 Vibration Analysis, Dynamic Balancing & Thermography 11.2 Preventive/Predictive Maintenance & Decommissioning 11.3 Non-Destructive Testing (NDT) Methods 11.4 Lubricant & Fluid Analysis 11.5 Commissioning: Pre-Start Checks, Run-In & Documentation
12 Chapter 12: Hydraulic Systems
12.1 Hydraulic Fundamentals: Pascal’s Law, Pressure, Flow & Power 12.2 Hydraulic Fluids, Reservoirs, Filtration & Contamination Control 12.3 Hydraulic Pumps: Gear, Vane & Piston Designs 12.4 Hydraulic Valves: Pressure, Directional & Flow Control 12.5 Hydraulic Actuators: Cylinders, Motors & Accumulators 12.6 Hydraulic Conductors, ISO 1219 Symbols & System Troubleshooting
13 Chapter 13: Conveying Systems, Material Handling & Automation
13.1 Belt Conveyors: Components, Tracking & Training 13.2 Screw, Bucket, Roller, Chain & Pneumatic Conveyors 13.3 Robotics & Automated Equipment
14 Chapter 14: Process Piping, Tanks & Vessels
14.1 Process Piping: Materials, Sizing, Fittings & Joining 14.2 Flanges, Gaskets & Piping Bolted-Joint Assembly 14.3 Tanks, Vessels & Containers: Installation, Inspection & Repair
15 Chapter 15: Materials, Fabrication, Cutting & Welding
15.1 Material Identification: Ferrous & Non-Ferrous Metals, Plastics 15.2 Heat Treatment of Metals 15.3 Oxy-Fuel & Plasma Arc Cutting 15.4 Welding Processes: SMAW, GMAW, GTAW, OFW & Equipment Care 15.5 Layout Procedures & Maintaining Precision Measuring Tools
3.5 Jacking, Skidding, Rollers & Moving Equipment
Key Takeaways Explain This Topic AI
A load raised on a jack must be cribbed and blocked as it rises — never work under a load supported only by hydraulic or mechanical jacks.
A box crib is generally limited to a height of about three times its narrowest base dimension, and the timbers must bear fully on each other at the corners.
Jacks must sit on a solid level base with the load centred on the saddle, because an off-centre or tilted jack can kick out under load.
Forklift rated capacity is quoted at a standard load centre, commonly 600 mm (24 in), and capacity drops sharply as the actual load centre moves further out.
Machinery rollers and skates must be positioned so the load stays inside the roller footprint, with the load centre of gravity kept low and tag lines used for control.
Last updated: August 2026
Sub-task B-7.03 (Selects hoisting/lifting and moving equipment) and B-8.02 (Performs hoist/lift and move) cover far more than cranes. Most heavy machinery inside a plant is moved without a crane — jacked, cribbed, rolled and skidded into place. This is core millwright work and it kills people who take shortcuts.
Jacks
Type Description Notes
Bottle jack Vertical hydraulic ram in a bottle-shaped body High capacity, short stroke; must be used within a few degrees of vertical
- Journal jack Hydraulic jack with a long screw extension Adjustable working height
- Toe jack Hydraulic jack with a low toe at the base Lifts a load with almost no clearance under it
- Air/hydraulic jack Shop-air driven hydraulic pump Fast repeated lifting
- Mechanical screw jack Acme screw, hand or wrench driven Holds position mechanically; will not bleed down
- Ratchet (track) jack Rack-and-pawl lifting jack Rugged; the handle kicks back violently if released under load
- Jacking Rules
Set the jack on a solid, level base — a steel plate or a hardwood pad spreading the load onto the floor. A jack sinking into fill or a floor drain tips and shoots out.
Centre the load on the saddle and make sure the lifting point on the machine is a designed jacking point capable of the load.
Jack the load in small increments and crib as you go. The rule is simple and absolute: the cribbing follows the load up, and the load is never left on the jack alone.
Never place any part of your body under a load supported only by jacks. Hydraulic jacks bleed down, seals fail and hoses burst.
Lower in small increments too , removing cribbing progressively — most jacking incidents happen on the way down.
Use two or more jacks in a coordinated sequence for a long machine, keeping the load level so it does not walk off a jack.
Inspect for leaking seals, bent rams, damaged saddles and illegible capacity markings and remove defective jacks from service.
- Cribbing and Blocking BOX CRIB Rules of thumb
- Use sound, square, hardwood or
- =============== engineered cribbing (no split,
- || || painted or rotten timber)
- ===================== - Each layer laid 90 degrees to the
- || || one below, with full corner bearing
- ===================== - Height limited to roughly 3x the
- || || narrowest base dimension
- ========================= - Keep the crib plumb and centred
- solid level floor - Wedges and shims only for final
- take-up, never as main support
Cribbing capacity depends on the wood species, timber size and the contact area at the corners — a crib carries load only where the timbers actually cross. Never build a crib on soft or uneven ground without a sill, and never mix timber sizes within a layer.
Rollers, Skates and Skidding
Method Description Application
Pipe rollers Round bar or pipe under a load on a flat steel plate or timber runway Simple and cheap; requires constant re-feeding of rollers at the front and is hard to steer
Machinery skates / rollers Purpose-built roller assemblies with steerable and fixed heads Standard for moving machine bases and gearboxes in a plant
Air casters (air bearings) Rubber torus inflated by shop air; the load floats on a film of air Very heavy loads on smooth, sealed floors; almost no floor loading concentration
- Skidding on plates Load slid on greased steel plates or PTFE-faced pads Short controlled moves, tight quarters
- Rail and dolly systems Load carried on trolleys along a temporary rail Long, repeatable moves
Roller rules:
Distribute the rollers so the load stays within the roller footprint at all times, and account for the centre of gravity shifting as the load tips over a floor joint or transition plate.
Keep the centre of gravity low and the load secured to the skates so it cannot walk off.
Never put hands or feet near a roller. Feed and adjust pipe rollers with a bar, never by hand.
Watch the floor rating and surface : expansion joints, floor drains, trench covers, and slab edges will stop or capsize a roller move.
Use tag lines for control and keep everyone out of the potential travel path — especially downhill of the load.
Pulling and Positioning Devices
Device Notes
Come-along (lever hoist) Ratcheting lever hoist with chain or wire rope; never extend the handle with a cheater bar — the rating assumes the standard handle length
Chain fall (hand chain hoist) Manual hoist with a hand chain; verify the load chain is not twisted or capsized on the hook block
Wire rope grip hoist (griphoist type) Pulls or lifts through the machine on any length of wire rope; the shear pin is a designed overload protection and must never be replaced with a bolt
Winch (electric or air) Fixed pull; verify anchorage capacity and keep at least the manufacturer's minimum wraps on the drum
Hydraulic push-pull rams Precise final positioning of heavy machinery
Always confirm the anchor point is rated for the load. Attaching a come-along to a handrail, a small pipe, or an unknown lug is a common and serious error.
Forklifts and Industrial Trucks
Powered lift trucks are designed, tested and used in Canada under the CSA B335 series , and operators must be trained and evaluated.
Rated capacity is quoted at a standard load centre — commonly 600 mm (24 in) from the face of the forks. As the actual load centre moves further out, the safe capacity drops steeply.
Worked example. A truck rated 2,500 kg at a 600 mm load centre picks up a gearbox whose centre of gravity is 900 mm from the fork face. The overturning moment is proportional to the distance, so the approximate available capacity is: 2,500 × 600 900 = 1,667 kg 2{,}500 \times \frac{600}{900} = 1{,}667\text{ kg} 2 , 500 × 900 600 = 1 , 667 kg
Always confirm against the actual data plate and load chart on the machine, and re-check the plate whenever an attachment is fitted — a fork extension, drum clamp or side-shifter reduces capacity and moves the load centre.
Stability: a counterbalanced lift truck is stable while the combined centre of gravity stays inside the stability triangle formed by the two front wheels and the pivot of the steer axle. It is why raising a load while travelling, turning with a raised load, or braking hard causes tip-overs.
Operating rules: travel with the forks low and tilted back; travel in reverse when the load blocks the view; sound the horn at blind corners; never lift personnel on the forks or on a pallet — only in an approved, secured personnel platform with the truck's controls attended; and set the mast vertical, lower the forks, apply the brake and remove the key when parking.