Study guide

1.5 Hand Tools, Portable Power Tools & Shop Machines

Red Seal Industrial Mechanic Millwright

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety & Occupational Skills

1.1 WHMIS, SDS & Hazardous Materials 1.2 Lockout/Tagout (LOTO) & Energy Isolation 1.3 Confined Space Entry & Fall Protection 1.4 Blueprint Reading, Trade Math & Precision Measurement Tools 1.5 Hand Tools, Portable Power Tools & Shop Machines 1.6 Access Equipment: Ladders, Scaffolds & Elevating Work Platforms 1.7 Planning Work, Permits, Communication & Mentoring

2 Chapter 2: Fasteners & Bolted Joints

2.1 Threaded Fasteners, Bolts & Thread Standards 2.2 Torque Values, Tightening Patterns & Thread Pitch/Gaging 2.3 Non-Threaded Fasteners, Pins, Keys & Anchors

3 Chapter 3: Rigging, Hoisting & Crane Signals

3.1 Sling Angles, Sling Types & Leg Tension Calculations 3.2 Working Load Limit (WLL) & Hardware Inspection 3.3 Centre of Gravity & Load Weight Estimation 3.4 Hoists, Overhead Cranes & Standard Hand Signals 3.5 Jacking, Skidding, Rollers & Moving Equipment 3.6 Lift Planning, Area Control & Rigging Equipment Maintenance

4 Chapter 4: Prime Movers & Electric Motors

4.1 Electric Motors, Enclosures, Frame Sizes & Synchronous Speed 4.2 Motor Installation, Nameplates & Overload Protection 4.3 Engine Prime Movers & Mechanical Drives Introduction

5 Chapter 5: Belt & Chain Mechanical Drives

5.1 V-Belts, Timing Belts & Sheave Alignment 5.2 Belt Tensioning, Pitch Diameter & Speed Ratios 5.3 Roller Chains, Sprocket Alignment & Lubrication 5.4 Clutches, Brakes & Torque Limiters

6 Chapter 6: Gear Drives, Couplings & Reducers

6.1 Gear Types, Geometry & Gear Ratios 6.2 Couplings (Rigid, Flexible, Fluid) & Installation 6.3 Shaft Keys, Keyways, Taper Sleeves & Hub Fits 6.4 Gear Reducers, Backlash & Mechanical Drive Troubleshooting

7 Chapter 7: Industrial Pumps & Systems

7.1 Centrifugal Pumps, Impellers & Performance Curves 7.2 Positive Displacement Pumps (Gear, Vane, Piston, Diaphragm) 7.3 Cavitation, NPSHa vs NPSHr & Pump Priming 7.4 Pump Maintenance, Packing & Mechanical Seals

8 Chapter 8: Compressors, Fans & Pneumatics

8.1 Reciprocating & Rotary Screw Air Compressors 8.2 Compressed Air Treatment, FRL Units & Air Receivers 8.3 Centrifugal & Axial Fans, Affinity Laws & Airflow 8.4 Pneumatic Circuits, Valves, Actuators & Troubleshooting 8.5 Vacuum Systems, Pumps & Venturi Generators

9 Chapter 9: Bearings, Lubrication & Seals

9.1 Plain Bearings, Bushings & Fits 9.2 Rolling Element Bearings & Installation 9.3 Bearing Heating Limits, Fits & Removal Tools 9.4 Industrial Lubricants, Viscosity, Grease NLGI Grades & Seals

10 Chapter 10: Precision Alignment & Foundations

10.1 Precision Shaft Alignment (Rim-and-Face & Reverse-Dial Methods) 10.2 Laser Alignment, Soft Foot Correction & Thermal Growth 10.3 Machinery Foundations, Leveling, Grouting & Dowelling

11 Chapter 11: Vibration Analysis & Predictive Maintenance

11.1 Vibration Analysis, Dynamic Balancing & Thermography 11.2 Preventive/Predictive Maintenance & Decommissioning 11.3 Non-Destructive Testing (NDT) Methods 11.4 Lubricant & Fluid Analysis 11.5 Commissioning: Pre-Start Checks, Run-In & Documentation

12 Chapter 12: Hydraulic Systems

12.1 Hydraulic Fundamentals: Pascal’s Law, Pressure, Flow & Power 12.2 Hydraulic Fluids, Reservoirs, Filtration & Contamination Control 12.3 Hydraulic Pumps: Gear, Vane & Piston Designs 12.4 Hydraulic Valves: Pressure, Directional & Flow Control 12.5 Hydraulic Actuators: Cylinders, Motors & Accumulators 12.6 Hydraulic Conductors, ISO 1219 Symbols & System Troubleshooting

13 Chapter 13: Conveying Systems, Material Handling & Automation

13.1 Belt Conveyors: Components, Tracking & Training 13.2 Screw, Bucket, Roller, Chain & Pneumatic Conveyors 13.3 Robotics & Automated Equipment

14 Chapter 14: Process Piping, Tanks & Vessels

14.1 Process Piping: Materials, Sizing, Fittings & Joining 14.2 Flanges, Gaskets & Piping Bolted-Joint Assembly 14.3 Tanks, Vessels & Containers: Installation, Inspection & Repair

15 Chapter 15: Materials, Fabrication, Cutting & Welding

15.1 Material Identification: Ferrous & Non-Ferrous Metals, Plastics 15.2 Heat Treatment of Metals 15.3 Oxy-Fuel & Plasma Arc Cutting 15.4 Welding Processes: SMAW, GMAW, GTAW, OFW & Equipment Care 15.5 Layout Procedures & Maintaining Precision Measuring Tools

1.5 Hand Tools, Portable Power Tools & Shop Machines

Key Takeaways Explain This Topic AI

An abrasive wheel must carry a maximum rated speed equal to or greater than the spindle speed of the tool it is mounted on, and must be ring-tested before mounting.

On a bench or pedestal grinder the work rest is set within 3 mm of the wheel and the tongue guard within 6 mm, and both are re-adjusted as the wheel wears.

Impact wrenches are never used to set a final torque value; they seat the fastener and a calibrated torque wrench then establishes preload.

Mushroomed chisel and punch heads must be ground back, because the work-hardened rim breaks off as high-velocity fragments when struck.

Work in a drill press must always be clamped or held in a vise — a drill grabbing an unclamped part turns it into a rotating blade, and gloves must never be worn at any rotating machine.

Last updated: August 2026

Task A-2 (Uses tools and equipment) carries 5 of the 25 questions in Major Work Activity A, split across hand and portable power tools, shop machines, and access equipment. These questions are practical and specific — guard clearances, wheel speeds, and the tools that must never be used for a given job.

Hand Tools

Tool Selection and safety points

Wrenches A 6-point socket or box end grips the flats and is preferred on tight or rounded fasteners; a 12-point offers more engagement angles but concentrates load on the corners. Pull a wrench, never push , so a slip does not drive your knuckles into the machine

Striking (slugging) wrench Heavy box wrench struck with a hammer for large flange and bearing nuts; use only where designed, and never strike a standard wrench

Torque wrench Beam, click, dial and digital types. Never use a torque wrench to loosen a fastener , and back a click wrench off to its lowest setting for storage so the spring does not take a set

Torque multiplier Planetary gearbox that multiplies input torque; the reaction arm must bear on a solid surface, never on a hand or a hose

  • Pliers and channel locks Gripping and holding only; never use as a wrench on a fastener that must be reused
  • Screwdrivers Match tip and shank to the fastener; a screwdriver is not a pry bar, chisel or punch

Hammers Ball peen for metal work, dead blow for assembly without marring, sledge for heavy work. A loose or cracked handle takes the hammer out of service

Chisels and punches Struck-tool heads work-harden and mushroom ; the mushroomed rim breaks off as shrapnel when struck. Dress heads back to a slight chamfer on a schedule

Files Single cut for finishing, double cut for fast removal. Never use a file without a handle — the tang will go through a hand if the file catches

Hacksaw Blade TPI chosen so at least three teeth contact the work ; too coarse a blade straddles thin material and strips teeth

Pullers Two- and three-jaw, hydraulic, and slide-hammer types. Centre the puller screw on the shaft end, protect the shaft centre, and never heat a bearing while a puller is loaded unless the procedure calls for it. Always drape a blanket over a loaded puller — a jaw that lets go becomes a projectile

Portable Power Tools

Electrical safety:

Tools must be CSA-certified and either Class I (grounded, three-prong) or Class II (double insulated, two-prong with the double-square symbol) . Never remove a ground pin.

A ground fault circuit interrupter (GFCI) is required for portable tools used outdoors, in wet locations, and in most construction and confined-space work.

Inspect cords before every use; remove tools with damaged cords, cracked housings or defeated guards from service and tag them.

Do not carry a tool by its cord, and unplug before changing accessories.

Pneumatic tools: connect with a safety whip check or restraint cable across each coupling, because a hose that separates under pressure whips violently. Never point an air nozzle at a person, and limit air blow-gun nozzle pressure per the applicable regulation.

The impact wrench rule. An impact wrench delivers uncontrolled, highly variable torque — it is a seating tool, not a torquing tool . Fasteners that require a specified preload (bearing lock nuts, coupling bolts, flange bolts, cylinder head bolts) are run down with an impact and then finished with a calibrated torque wrench or a tensioner.

Abrasive Wheels and Grinders

Abrasive wheel failure is one of the most severe injury sources in a shop.

Speed rating. The wheel's maximum rated RPM printed on its blotter must be equal to or greater than the no-load spindle speed of the tool. Never fit a 6,000 RPM wheel on a 10,000 RPM angle grinder.

Ring test. Before mounting, suspend the wheel on a pin and tap it lightly with a non-metallic handle about 45 degrees each side of vertical. A clear ring means the wheel is sound; a dull thud means it is cracked — destroy it.

Mounting. Use matched flanges of the correct diameter with blotters (paper washers) on both sides. Tighten the nut only enough to drive the wheel; over-tightening cracks it.

Run-in. After mounting, stand to the side and run the wheel at operating speed for a full minute before use.

Bench and pedestal grinder guarding: the work rest is set within 3 mm (1/8 in) of the wheel face and the tongue guard within 6 mm (1/4 in) of the wheel periphery. Both must be re-adjusted as the wheel wears down. A gap larger than that lets the work be dragged down between the rest and the wheel.

Side grinding. Only wheels specifically rated for side loading (such as a Type 27 depressed-centre wheel) may be used on their side. Grinding on the side of a straight Type 1 wheel can shatter it.

Always wear a face shield over safety glasses when grinding, and never grind aluminum, brass or wood on a wheel intended for steel — soft metal loads the wheel and causes bursting.

Shop Machines (A-2.02)

Machine Key safety and technique points

Drill press Clamp the work or hold it in a vise. A drill that grabs spins an unclamped part into a rotating blade. Select speed from the cutting-speed formula for the material and drill size, use cutting fluid on steel, and peck-drill deep holes to clear chips

Engine lathe Remove the chuck key before starting — this is the single most common lathe injury cause. Set the tool bit on centre height, guard the chuck, never measure or clean chips while the spindle turns, and use a brush not fingers for chips

Milling machine Secure the work in a vise or clamp it to the table; understand climb versus conventional milling; stop the spindle before measuring

Horizontal / vertical band saw Match blade TPI to material thickness (three teeth in the cut), adjust the guides close to the work, and keep the upper guard down to the minimum working height

Hydraulic press Never exceed the rated capacity ; use the shield, chain the workpiece or use a press guard because parts fly when they release, and stand out of the line of the ram

Pedestal grinder / abrasive chop saw As above, plus secure clamping and spark direction away from combustibles

Universal machine rules: no gloves, loose sleeves, jewellery or unrestrained long hair at any rotating machine; guards in place; lock out before changing belts, gears or making adjustments inside a guard; and never leave a machine running unattended.

Fabricating a Work Piece (A-3.02)

The standard sequence a millwright follows to make a part:

Read the drawing and confirm material, dimensions, tolerances and finish.

Select and verify material — the right grade and enough stock allowance for machining and cutting kerf.

Lay out from an established datum (see section 15.5).

Cut oversize , leaving machining allowance.

Machine to size , working from the datum, roughing then finishing.

Drill, tap, bore and key as required.

Deburr and break sharp edges — a burr causes assembly interference and a sharp corner is a fatigue initiator.

Verify every dimension against the drawing before the part leaves the bench, and record any deviation.