Study guide

11.4 Lubricant & Fluid Analysis

Red Seal Industrial Mechanic Millwright

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety & Occupational Skills

1.1 WHMIS, SDS & Hazardous Materials 1.2 Lockout/Tagout (LOTO) & Energy Isolation 1.3 Confined Space Entry & Fall Protection 1.4 Blueprint Reading, Trade Math & Precision Measurement Tools 1.5 Hand Tools, Portable Power Tools & Shop Machines 1.6 Access Equipment: Ladders, Scaffolds & Elevating Work Platforms 1.7 Planning Work, Permits, Communication & Mentoring

2 Chapter 2: Fasteners & Bolted Joints

2.1 Threaded Fasteners, Bolts & Thread Standards 2.2 Torque Values, Tightening Patterns & Thread Pitch/Gaging 2.3 Non-Threaded Fasteners, Pins, Keys & Anchors

3 Chapter 3: Rigging, Hoisting & Crane Signals

3.1 Sling Angles, Sling Types & Leg Tension Calculations 3.2 Working Load Limit (WLL) & Hardware Inspection 3.3 Centre of Gravity & Load Weight Estimation 3.4 Hoists, Overhead Cranes & Standard Hand Signals 3.5 Jacking, Skidding, Rollers & Moving Equipment 3.6 Lift Planning, Area Control & Rigging Equipment Maintenance

4 Chapter 4: Prime Movers & Electric Motors

4.1 Electric Motors, Enclosures, Frame Sizes & Synchronous Speed 4.2 Motor Installation, Nameplates & Overload Protection 4.3 Engine Prime Movers & Mechanical Drives Introduction

5 Chapter 5: Belt & Chain Mechanical Drives

5.1 V-Belts, Timing Belts & Sheave Alignment 5.2 Belt Tensioning, Pitch Diameter & Speed Ratios 5.3 Roller Chains, Sprocket Alignment & Lubrication 5.4 Clutches, Brakes & Torque Limiters

6 Chapter 6: Gear Drives, Couplings & Reducers

6.1 Gear Types, Geometry & Gear Ratios 6.2 Couplings (Rigid, Flexible, Fluid) & Installation 6.3 Shaft Keys, Keyways, Taper Sleeves & Hub Fits 6.4 Gear Reducers, Backlash & Mechanical Drive Troubleshooting

7 Chapter 7: Industrial Pumps & Systems

7.1 Centrifugal Pumps, Impellers & Performance Curves 7.2 Positive Displacement Pumps (Gear, Vane, Piston, Diaphragm) 7.3 Cavitation, NPSHa vs NPSHr & Pump Priming 7.4 Pump Maintenance, Packing & Mechanical Seals

8 Chapter 8: Compressors, Fans & Pneumatics

8.1 Reciprocating & Rotary Screw Air Compressors 8.2 Compressed Air Treatment, FRL Units & Air Receivers 8.3 Centrifugal & Axial Fans, Affinity Laws & Airflow 8.4 Pneumatic Circuits, Valves, Actuators & Troubleshooting 8.5 Vacuum Systems, Pumps & Venturi Generators

9 Chapter 9: Bearings, Lubrication & Seals

9.1 Plain Bearings, Bushings & Fits 9.2 Rolling Element Bearings & Installation 9.3 Bearing Heating Limits, Fits & Removal Tools 9.4 Industrial Lubricants, Viscosity, Grease NLGI Grades & Seals

10 Chapter 10: Precision Alignment & Foundations

10.1 Precision Shaft Alignment (Rim-and-Face & Reverse-Dial Methods) 10.2 Laser Alignment, Soft Foot Correction & Thermal Growth 10.3 Machinery Foundations, Leveling, Grouting & Dowelling

11 Chapter 11: Vibration Analysis & Predictive Maintenance

11.1 Vibration Analysis, Dynamic Balancing & Thermography 11.2 Preventive/Predictive Maintenance & Decommissioning 11.3 Non-Destructive Testing (NDT) Methods 11.4 Lubricant & Fluid Analysis 11.5 Commissioning: Pre-Start Checks, Run-In & Documentation

12 Chapter 12: Hydraulic Systems

12.1 Hydraulic Fundamentals: Pascal’s Law, Pressure, Flow & Power 12.2 Hydraulic Fluids, Reservoirs, Filtration & Contamination Control 12.3 Hydraulic Pumps: Gear, Vane & Piston Designs 12.4 Hydraulic Valves: Pressure, Directional & Flow Control 12.5 Hydraulic Actuators: Cylinders, Motors & Accumulators 12.6 Hydraulic Conductors, ISO 1219 Symbols & System Troubleshooting

13 Chapter 13: Conveying Systems, Material Handling & Automation

13.1 Belt Conveyors: Components, Tracking & Training 13.2 Screw, Bucket, Roller, Chain & Pneumatic Conveyors 13.3 Robotics & Automated Equipment

14 Chapter 14: Process Piping, Tanks & Vessels

14.1 Process Piping: Materials, Sizing, Fittings & Joining 14.2 Flanges, Gaskets & Piping Bolted-Joint Assembly 14.3 Tanks, Vessels & Containers: Installation, Inspection & Repair

15 Chapter 15: Materials, Fabrication, Cutting & Welding

15.1 Material Identification: Ferrous & Non-Ferrous Metals, Plastics 15.2 Heat Treatment of Metals 15.3 Oxy-Fuel & Plasma Arc Cutting 15.4 Welding Processes: SMAW, GMAW, GTAW, OFW & Equipment Care 15.5 Layout Procedures & Maintaining Precision Measuring Tools

11.4 Lubricant & Fluid Analysis

Key Takeaways Explain This Topic AI

A representative oil sample is taken from a live, turbulent zone in the system while the equipment is at operating temperature, never from the bottom of a sump or a drained line.

Wear metals identify the failing component: iron points to gears and races, copper to bronze bushings and thrust washers, tin and lead to babbitt, and silicon to dirt ingress.

A viscosity change of more than about 10% from the new-oil specification is a standard alarm limit, indicating oxidation, fuel or solvent dilution, or a wrong-oil top-up.

A rising total acid number shows oxidation and additive depletion, while a falling total base number in an engine oil shows the reserve alkalinity is exhausted.

Particle counting to ISO 4406 measures contamination while spectrographic analysis measures wear and additive chemistry — the two answer different questions and are used together.

Last updated: August 2026

Sub-task F-23.05 (Performs fluid analysis procedures) turns a routine oil sample into an early warning of failure. Oil analysis answers three separate questions, and a good program keeps them distinct:

Is the lubricant still fit for service? — viscosity, acid number, additive levels, oxidation.

Is the lubricant contaminated? — particle count, water, glycol, fuel, soot.

Is the machine wearing? — wear metals, ferrous density, particle shape.

Taking a Representative Sample

The single largest source of bad analysis data is a bad sample.

Rule Reason

Sample with the machine running at normal operating temperature Wear particles and water stay suspended; a cold, settled system gives a falsely clean result

Sample from a live, turbulent zone — a dedicated sampling valve on a pressurized or return line, or a drop-tube in a circulating sump Static tank bottoms concentrate sludge and water, and drain-port samples are unrepresentative

Sample upstream of the filter, downstream of the components Otherwise the filter removes the very evidence being sampled

Flush the sampling valve before filling the bottle Removes the stagnant slug of oil sitting in the port

Use clean, certified sample bottles and cap them immediately Ambient dust will corrupt a particle count in seconds

Sample the same point, the same way, at the same interval every time Analysis is a trend tool; a single result out of context means very little

Label completely — equipment ID, sample point, date, hours on oil, hours on machine, oil brand and grade, any top-ups The lab cannot interpret without this

Laboratory Tests and What They Reveal

Test Measures Indicates

Kinematic viscosity at 40 C Resistance to flow Increase: oxidation, contamination with a heavier oil, soot loading. Decrease: fuel or solvent dilution, shear-down of a VI improver, wrong-oil top-up

Spectrographic (elemental) analysis Parts per million of wear metals, contaminants and additives Which component is wearing, what dirt is present, and whether the additive package is depleted

Particle count (ISO 4406) Particles per millilitre at 4, 6 and 14 micron Cleanliness against target; the primary hydraulic system health metric

Water content (crackle test, Karl Fischer) Free, emulsified and dissolved water Seal or cooler leaks, condensation, wash-down ingress

Total acid number (TAN) Acidic by-products Oxidation and additive depletion; a rising TAN forecasts varnish and corrosion

Total base number (TBN) Reserve alkalinity (engine oils) Remaining ability to neutralize combustion acids; a falling TBN sets the drain interval

Ferrous density / PQ index Total ferromagnetic material Large wear particles that spectrographic analysis misses

Analytical ferrography Particle size, shape and colour under a microscope The wear mechanism — cutting, fatigue spalling, sliding, corrosion

FTIR (infrared) Oxidation, nitration, sulphation, soot, glycol Chemical degradation and specific contaminants

The key limitation of spectrographic analysis: most spectrometers only reliably detect particles below about 5–10 micron . A bearing shedding large spalls can show low wear-metal ppm while it is failing, which is exactly why ferrous density and ferrography are added when a problem is suspected.

Reading Wear Metals

  • Element Common source in industrial machinery
  • Iron (Fe) Gears, shafts, bearing races and rollers, housings, rust
  • Copper (Cu) Bronze bushings, thrust washers, cages, oil cooler cores
  • Lead (Pb) / Tin (Sn) Babbitt journal bearings, solder from a cooler
  • Aluminum (Al) Pistons, thrust bearings, housings, or dirt (as aluminosilicate)
  • Chromium (Cr) Plated shafts, rings, some bearing steels
  • Silicon (Si) Dirt ingress — silica dust; also silicone antifoam or sealant
  • Sodium (Na) / Potassium (K) Coolant leak (glycol inhibitors) or salt water ingress

Zinc (Zn), Phosphorus (P), Calcium (Ca), Molybdenum (Mo), Boron (B) Additives — anti-wear, detergent, dispersant; a decline signals additive depletion

Interpretation is about rate, not absolute value. A gearbox that reads 40 ppm iron consistently is normal for that gearbox; the same reading in a unit that has always run at 8 ppm is an alarm. Trend every point against its own history, and always correlate with hours on the oil — ppm accumulate over time in a non-drained sump.

A classic diagnostic pair: rising silicon together with rising iron and copper means dirt is entering through a failed breather or seal and is abrading the components. The fix is the ingress path, not the oil.

Water and Contamination Limits

  • Contaminant Typical concern threshold
  • Water in industrial oil Above roughly 500 ppm (0.05%) is a caution; free water is always actionable
  • Water in hydraulic oil Tighter still; hazy oil already means the saturation point has been passed
  • Glycol Any detectable glycol is a serious alarm — it forms abrasive oil balls and destroys bearings
  • Fuel dilution (engines) Above about 2–5% depending on the engine builder
  • Soot (diesel) Above the engine maker's limit; increases viscosity and abrasive wear

A quick field crackle test — a drop of oil on a hot plate at about 150 C — audibly crackles when free or emulsified water is present, giving an immediate indication between lab samples.

Grease Analysis

Grease can be analyzed too, though sampling is harder. Useful tests are consistency (penetration), oil separation (bleed), oxidation, wear metals and contamination. A purged sample taken from a bearing's grease outlet during relubrication tells you what is happening inside the bearing. Look for hardening or dry, crusty grease (oxidation or over-temperature), a soupy consistency (mechanical shear or wrong-grease mixing), and grey or metallic discolouration (wear).

Grease incompatibility is a common self-inflicted failure: mixing a lithium-complex grease with a polyurea grease can collapse the thickener into a fluid that runs out of the bearing. Confirm compatibility before changing grease types, and where in doubt, purge the bearing completely.

Converting Results into Action

Result Action

Viscosity outside about ±10% of specification Confirm the correct product was used, investigate contamination or oxidation, change the oil

Particle count above target code Check breathers, seals and filter condition; add or upgrade filtration; consider a kidney-loop flush

Water above limit Find the ingress path — cooler leak, seal, breather, wash-down — then dry or replace the charge

Rising wear metals with rising ferrous density Increase inspection frequency, correlate with vibration and thermography, plan an intervention

  • Silicon rising with wear metals Fix the ingress path first; oil changes alone will not stop the wear
  • Additive elements declining The oil is at the end of its useful life regardless of how clean it looks

Oil analysis is one leg of a condition-monitoring program. Its power multiplies when correlated with vibration analysis and thermography from section 11.1: a gearbox with rising iron, a rising 1x gearmesh vibration and a warm bearing housing is a confirmed finding, not a suspicion.