Study guide

1.2 RSOS Blueprint & Exam Weightings

Red Seal Truck and Transport Mechanic 310T

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 RSOS Blueprint & Exam Weightings 1.3 How to Study for the 310T Red Seal

2 Common Occupational Skills

2.1 Safety, PPE & Hazardous Materials 2.2 Tools, Hoisting & Welding Protection 2.3 Documentation, Service Info & Fasteners 2.4 Communication & Mentoring

3 Diesel Engines — Base Engine & Supporting Systems

3.1 Base Engines & Compression Ignition 3.2 Lubrication Systems 3.3 Intake, Turbocharging & Charge-Air Cooling 3.4 Exhaust Aftertreatment: EGR, DOC, DPF & SCR

4 Diesel Engines — Management, Fuel, Retarders & Cooling

4.1 Engine Management Systems 4.2 Fuel Delivery Systems 4.3 Engine Retarder Systems 4.4 Cooling Systems

5 Air Systems

5.1 Air Compressor & Governor 5.2 Air Dryer, Relay & Protection Valves 5.3 Air System Diagnosis 5.4 Air System Service & Repair

6 Foundation Brakes, Spring Brakes & ABS

6.1 S-Cam Foundation Brakes 6.2 Spring Brakes & Parking/Emergency 6.3 ABS & Slack Adjusters 6.4 Brake Diagnosis & Repair

7 Batteries, Charging, Spark Ignition & Starting

7.1 Battery Systems 7.2 Charging Systems 7.3 Spark Ignition Systems 7.4 Starting Systems

8 Electrical Components, J1939 & Advanced Diagnostics

8.1 Electrical Components & Accessories 8.2 Vehicle Management Systems & J1939 8.3 Parasitic Draw & No-Code Diagnostics

9 Clutches & Transmissions

9.1 Clutches & Clutch Brakes 9.2 Manual Transmissions & Transfer Cases 9.3 Automatic Transmissions 9.4 Automated Manual Transmissions

10 Drivelines, Drive Axles & Drivetrain Retarders

10.1 Driveline Systems 10.2 Drive Axle Assemblies 10.3 Drivetrain Retarders

11 Steering, Chassis, Suspension & Hitches

11.1 Steering Systems 11.2 Chassis & Frames 11.3 Suspension Systems 11.4 Hitches & Couplers

12 Tires, Wheels, Hubs & Cab Systems

12.1 Tires, Wheels & Hubs 12.2 Interior Cab Components 12.3 Exterior Cab Components

13 Trailers & Transport Bodies

13.1 Trailer Components & Accessories 13.2 Trailer Heating & Refrigeration Systems 13.3 Trailer Diagnosis Scenarios

14 Cab Climate Control Systems

14.1 Heating & Ventilation 14.2 Air Conditioning Systems 14.3 Refrigerant Identification, Recovery & Leak Detection

15 Hydraulic Systems & Power Take-Off

15.1 Hydraulic Fundamentals 15.2 Hydraulic Diagnosis 15.3 Repair, Contamination Control & PTO

16 Hybrid & Electric Vehicle Systems

16.1 Hybrid Vehicles 16.2 Electric Vehicles (EV) 16.3 High-Voltage Safety Procedures

1.2 RSOS Blueprint & Exam Weightings

Key Takeaways Explain This Topic AI

The exam is built from the Red Seal Occupational Standard (RSOS), organized into 11 Major Work Activities (Blocks A through K), each broken into Tasks and further into Sub-tasks - exam questions are written against sub-tasks

The official question distribution across the 135-question exam is: A-8, B-21, C-17, D-22, E-17, F-18, G-5, H-8, I-7, J-8, K-4

Block D (Electrical & Electronic Systems, 22 questions, ~16%) and Block B (Engines & Supporting Systems, 21 questions, ~16%) are the two largest single blocks - together with Block C (Air & Brake Systems, 17 questions) and Block F (Steering/Chassis/Suspension, 18 questions) they carry the bulk of the exam

The consumer-facing exam-meta marketing page on this site groups content into 6 simplified domains for browsing convenience - candidates must study the official 11-block RSOS structure, not the simplified marketing groupings, to match how the exam is actually written

Block K (Hybrid & Electric Vehicles) is the newest and smallest block at only 4 questions, but it is a dedicated block precisely because commercial fleets are electrifying and Red Seal added it to keep the standard current

Last updated: July 2026

What The RSOS Actually Is

The Red Seal Occupational Standard (RSOS) is the official document that defines everything a certified Truck and Transport Mechanic must know and be able to do. It is not a study guide - it is the source document that the exam-writing committee uses to build every single question on your exam. Understanding its structure is the single highest-leverage thing you can do before opening a textbook, because it tells you exactly how much of the exam each subject area controls.

The RSOS organizes the trade into Major Work Activities (MWAs) , labelled Block A through Block K - 11 blocks in total. Each block breaks down further into Tasks (broad job functions within that block), and each Task breaks down again into Sub-tasks (specific, testable skills and knowledge points). This is the critical mechanic to internalize:

Exam questions are written against Sub-tasks, not against Blocks or Tasks directly.

A Block is simply the sum of its Tasks' sub-tasks. When you see "Block C: Air & Brake Systems, 17 questions," that is not one general theme tested loosely - it is a fixed number of questions drawn from a defined list of specific sub-tasks under Task 13 (air systems) and Task 14 (brake systems). Studying at the sub-task level, not just the block-title level, is what separates candidates who recognize a scenario from candidates who only recognize a chapter heading.

The Official Block-By-Block Question Count

The following table is the exam's actual blueprint, taken directly from the red-seal.ca exam-information page for the trade. It is the single most important table in this entire study guide - return to it whenever you are deciding where to spend your next study hour.

  • Block Major Work Activity Questions % of Exam
  • A Common Occupational Skills 8 ~6%
  • B Engines and Supporting Systems 21 ~16%
  • C Air and Brake Systems 17 ~13%
  • D Electrical and Electronic Systems 22 ~16%
  • E Drive Trains 17 ~13%
  • F Steering, Chassis, Suspension, and Tires 18 ~13%
  • G Cabs 5 ~4%
  • H Trailers 8 ~6%
  • I Climate Control 7 ~5%
  • J Hydraulic Systems 8 ~6%
  • K Hybrid and Electric Vehicles 4 ~3%
  • Total 135 100%

A few patterns worth acting on immediately:

Block D (22Q) and Block B (21Q) are the two heaviest blocks. Electrical/electronic systems and engines together account for nearly a third of the exam - roughly 43 of your 135 questions.

Blocks C, E, and F (17, 17, 18Q) form a dense middle tier covering air/brakes, drive trains, and steering/chassis/suspension/tires. Combined with B and D, these five blocks (B, C, D, E, F) account for 95 of 135 questions - about 70% of the entire exam.

Blocks G, H, I, J, and K are lighter (4-8 questions each) but should not be skipped entirely - together they still total 32 questions, more than the whole of Block B or D on their own.

If you have limited study time before your sitting, this table - not a generic chapter list - should decide your hour-by-hour allocation.

The MWA to Task to Sub-task Hierarchy In Practice

To make the hierarchy concrete, consider Block C (Air and Brake Systems) . It contains two Tasks: Task 13 (Air Systems) and Task 14 (Brake Systems) . Task 13's sub-tasks cover the air compressor and governor, the air dryer and supply-side valves, and system-level leak/pressure diagnosis. Task 14's sub-tasks cover foundation brakes (S-cam, drums, shoes), spring brakes and parking/emergency function, ABS and slack adjusters, and integrated brake diagnosis. Every one of Block C's 17 exam questions traces back to one of these named sub-tasks - there is no "general air brake trivia" category floating outside the standard.

This matters for study strategy in two ways:

Breadth beats depth within a block. Because a block's questions are spread across every sub-task under its Tasks, mastering one sub-task deeply while ignoring another under the same Task still leaves exam points on the table. A candidate who knows the air compressor cold but has never studied slack adjuster stroke limits is still exposed on Block C questions.

Scenario framing follows sub-task language. RSOS sub-tasks are typically phrased as job-real actions - "diagnose," "inspect," "service," "repair." Expect exam items to mirror that phrasing: a stem describing symptoms and asking what a technician should diagnose or do next, rather than a bare definitional question. Studying sub-task action verbs, not just component names, prepares you for the actual question style.

This chapter's companion chapters (2 through 16) are organized to walk every Block A-K Task in order, so working through this guide sequentially gives you sub-task-level coverage of the entire RSOS - not just the block titles.

Why This Site's Simplified 6-Domain View Is Not What You Should Study

This site's own exam overview page (and other consumer-facing marketing pages) group the trade's content into 6 simplified domains for easy browsing - things like "Brakes (Air), Steering & Suspension (~24%)" or "Diesel Engines, Fuel & Emissions (~20%)." These groupings are useful for getting an intuitive feel for the trade at a glance, and they are a reasonable approximation built by merging adjacent official blocks together for marketing readability.

But they are not the structure the exam is written from , and you should not build your study calendar around the 6-domain view. Two concrete gaps to be aware of:

Simplified marketing domain What it merges Why it under-specifies the real exam

"Brakes (Air), Steering & Suspension" (~24%) Blocks C + F Hides that Air/Brakes (C) and Steering/Chassis/Suspension/Tires (F) are tested as two separate 17Q and 18Q blocks with distinct sub-tasks

"HVAC, Hydraulics & Diagnostics" (~12%) Blocks I + J (+ general diagnostics) Hides that Climate Control (I, 7Q) and Hydraulic Systems (J, 8Q) are separately defined blocks, and omits that Cabs (G) and Hybrid/EV (K) exist as their own blocks entirely

The simplified view also has no place at all for Block G (Cabs) or Block K (Hybrid and Electric Vehicles) as standalone categories - they get folded into other groupings or left implicit. If you only studied from a 6-domain breakdown, you could walk into the exam having never deliberately reviewed cab electrical accessories or HEV high-voltage safety, and lose points on Blocks G and K that a candidate using the official 11-block RSOS would have covered.

The rule for this study guide: use the 11-block, A-through-K structure in this table as your map. Treat any simplified domain grouping you see elsewhere on this site as a marketing summary, never as your study syllabus.