Study guide

4.1 Spray Polyurethane Foam (SPF) and Liquid-Applied Protective Coatings

California C-39 Roofing Contractor Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Planning, Codes, and Roofing Estimating

1.1 California Building Codes, Title 24 Energy Standards, and Plan Reading 1.2 Roof Geometry, Area Calculations, and Pitch Multipliers 1.3 Material Takeoffs, Squares, and Waste Calculations 1.4 Roof System Selection, Specifications, Permits, and Project Scheduling 1.5 Labor Production Rates, Overhead, Profit, and Roofing Bid Pricing

2 Chapter 2: Job Site Preparation and Substrate Remediation

2.1 Jobsite Protection, Material Staging, and Temporary Weatherproofing 2.2 Tear-Off Procedures, Overlay Limitations, and Hazardous Materials 2.3 Roof Deck Inspection, Substrate Preparation, and Sheathing Repairs

3 Chapter 3: Low-Slope Roof Systems — Built-Up, Modified Bitumen, and Single-Ply

3.1 Built-Up Roofing (BUR) Systems, Felts, and Hot Bitumen Application 3.2 Modified Bitumen Membrane Systems (APP vs. SBS) and Installation 3.3 Single-Ply Roofing Membranes (TPO, PVC, EPDM) and Seaming Methods

4 Chapter 4: Low-Slope Roof Systems — SPF, Coatings, Flashings, and Maintenance

4.1 Spray Polyurethane Foam (SPF) and Liquid-Applied Protective Coatings 4.2 Low-Slope Drainage, Perimeters, Penetration Flashings, and Scuppers 4.3 Low-Slope Diagnostics, Blister Repairs, and Preventative Maintenance

5 Chapter 5: Steep-Slope Roofing — Flashing, Underlayment, and Ventilation

5.1 Steep-Slope Underlayments, Felt Grades, and Self-Adhering Ice/Water Barriers 5.2 Flashing Details: Valleys, Drip Edges, Step Flashing, Aprons, and Crickets 5.3 Attic and Roof Ventilation: NFVA Requirements, Vent Types, and Airflow Balance

6 Chapter 6: Steep-Slope Roofing — Materials, Installation, and Repair

6.1 Asphalt Shingle Installation, Fastening Patterns, and Wind/Slope Requirements 6.2 Concrete and Clay Tile Roofing (TRI Standards, Battens, and Fastening) 6.3 Standing Seam Metal Panels, Wood Shakes, Slate, and Steep-Slope Repairs 6.4 Steep-Slope Leak Diagnosis, Targeted Repairs, and the Repair-or-Replace Decision

7 Chapter 7: California Roofing Safety — Cal/OSHA, Fall Protection, and Hazards

7.1 Cal/OSHA Fall Protection: Residential Roofing (§1731), Roof Hazards (§1730), and PFAS 7.2 Cal/OSHA Ladder Safety, Scaffold Erection, and Power Line Clearance 7.3 Heat Illness Prevention (CCR §3395), Hot Asphalt Safety, and Personnel PPE 7.4 Injury and Illness Prevention Program, Safety Training, Recordkeeping, and Cal/OSHA Reporting 7.5 Hazard Communication, Asbestos, Lead, and Silica: Managing Unknown Materials

8 Chapter 8: CSLB Licensing Law and Business Organization

8.1 CSLB Licensing Classifications, Bond Requirements, and License Law 8.2 Business Entity Choice, Personnel of Record, and Qualifier Responsibilities 8.3 Advertising Rules, Home Improvement Salespersons, and Subcontracting

9 Chapter 9: Business Finances, Financial Reporting, and Taxes

9.1 Cash Management, Job Costing, and Working Capital 9.2 Budgeting, Business Planning, and Break-Even Analysis 9.3 Financial Reporting: Statements, Accounting Methods, and Key Ratios 9.4 Federal and California Taxes for Roofing Contractors

10 Chapter 10: Employment Requirements, Supervision, and Payroll

10.1 Hiring: Worker Classification, Verification, and New-Hire Reporting 10.2 Supervising and Training Employees 10.3 Performance Evaluation, Personnel Records, and Termination 10.4 California Payroll: Wages, Overtime, Meal and Rest Periods, and Deposits

11 Chapter 11: Insurance, Bonds, and Payment Remedies

11.1 Workers' Compensation Insurance for California Roofing Contractors 11.2 Business Insurance and Surety Bonds 11.3 California Mechanics Lien Law, 20-Day Preliminary Notices, and Lien Waivers

12 Chapter 12: Contract Requirements, Bidding, and Project Execution

12.1 California Roofing Contracts, Home Improvement Law (B&P §7159), and Warranties 12.2 Bidding Practices, Bid Documents, and Competitive Bidding Law 12.3 Job Cost Control and Change Order Management 12.4 Project Organization, Scheduling, and Documentation 12.5 Payments: Progress Payments, Retention, and California Prompt Payment Law

13 Chapter 13: Public Works Roofing Projects

13.1 Prevailing Wage, DIR Registration, and Certified Payroll 13.2 Public Works Bonding and Insurance Requirements

4.1 Spray Polyurethane Foam (SPF) and Liquid-Applied Protective Coatings

Key Takeaways Explain This Topic AI

Closed-cell spray polyurethane foam (SPF) for roofing is a two-component thermoset plastic mixed at a 1:1 volumetric ratio, formulated to an in-place density of 2.5 to 3.0 lbs/cu ft with a compressive strength of 40–45 psi and >90% closed-cell structure.

SPF must be installed in incremental passes (lifts) of 0.5 to 1.5 inches, never exceeding 2.0 inches in a single pass to prevent runaway exothermic heat accumulation that causes internal scorching, charring, split fissures, and fire hazards.

Substrate preparation requires complete removal of loose and embedded gravel via spudding and vacuuming down to smooth asphalt on existing BUR, moisture levels strictly under 8–10%, and rust-inhibitive or epoxy priming on metal and masonry surfaces.

Because SPF degrades rapidly under solar ultraviolet (UV) radiation within days, protective elastomeric coatings (acrylic, silicone, or polyurethane) must be applied at specified Dry Film Thickness (DFT = WFT × % Solids by Volume), typically 20 to 30 dry mils in two contrasting coats.

California Energy Code Title 24 cool roof standards mandate roof coatings on low-slope buildings to achieve minimum aged solar reflectance (≥ 0.63) and thermal emittance (≥ 0.75) or a Solar Reflectance Index (SRI) ≥ 75, often reinforced with broadcast ceramic granules for impact and slip resistance.

Last updated: September 2026

Spray Polyurethane Foam (SPF) and Liquid-Applied Protective Coatings

Trade Overview: Spray Polyurethane Foam (SPF) roofing systems provide a seamless, monolithic thermal insulation and waterproofing barrier sprayed directly onto commercial low-slope roof decks. Because SPF forms in situ through a rapid chemical reaction, successful field installation requires strict control of chemical mixing ratios, ambient temperatures, substrate moisture, and incremental pass thicknesses. Furthermore, because unprotected polyurethane foam degrades under ultraviolet (UV) radiation within days, an elastomeric protective coating system is mandatory under California Building Code Chapter 15 and Title 24 Energy Standards.

SPF Chemistry, Mixing Ratio, and Physical Properties

Spray Polyurethane Foam used in roofing is a rigid, closed-cell thermoset plastic formed by combining two liquid chemical components at the spray gun tip at high pressure (1,000 to 1,500 psi) and elevated temperature (110°F to 140°F):

A-Side Component (Isocyanate): Typically polymeric methylene diphenyl diisocyanate (PMDI). It acts as the hardener and cross-linking reactant.

B-Side Component (Polyol Resin Blend): A proprietary blend of polyols, chemical blowing agents (hydrofluoroolefins [HFOs] or water), amine catalysts, silicone surfactants, and flame retardants.

Mixing Ratio: The proportioning equipment must deliver the A and B components at an exact 1:1 volumetric ratio . An "off-ratio" mixture results in severe physical defects: excess isocyanate creates a brittle, friable, dark-brown foam with poor adhesion, while excess polyol creates a spongy, gummy, soft foam with low compressive strength and dimensional shrinkage.

Material Standards and Physical Requirements (ASTM C1029)

Roofing-grade SPF must comply with ASTM C1029 (Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation), categorized as Type III or Type IV:

In-Place Core Density (ASTM D1622): Must range between 2.5 to 3.0 pounds per cubic foot (lbs/cu ft or pcf) . Wall-insulation foam (typically 1.8 to 2.0 pcf) is prohibited on roofs because it lacks the mechanical strength to support roof foot traffic, maintenance loads, and hail impact.

Compressive Strength (ASTM D1621): Minimum 40 to 45 pounds per square inch (psi) parallel to rise.

Closed-Cell Content (ASTM D2856): Must exceed 90% closed cells . This high closed-cell percentage prevents water absorption and liquid water migration through the foam body.

Thermal Resistance (R-Value): Provides an initial aged thermal resistance of approximately R-6.2 to R-6.7 per inch of thickness.

Lift Thickness and Exothermic Heat Dynamics

The reaction between isocyanate and polyol is intensely exothermic , generating internal core temperatures that easily exceed 300°F (149°C) as the liquid expands 25 to 30 times its original volume:

Incremental Passes (Lifts): Foam must be applied in passes ranging from 0.5 inch to 1.5 inches in thickness. Each lift must be allowed to fully react, expand, and cool before applying subsequent passes.

Maximum Pass Thickness: A single pass must never exceed 2.0 inches . Spraying passes thicker than 2 inches traps extreme exothermic heat inside the core. This heat accumulation causes internal scorching, charring, cell rupture, permanent loss of compressive strength, split fissures, and in extreme cases, spontaneous subsurface smoldering combustion hours after application.

Minimum Total Thickness: The total finished SPF thickness across the roof field is typically a minimum of 1.0 inch to 1.5 inches , feathered smoothly up perimeters, curbs, and penetrations to a minimum height of 8 inches .

Surface Texture Classifications: According to the Spray Polyurethane Foam Alliance (SPFA) and NRCA, acceptable surface textures for coating application are Smooth finish and Orange peel finish . Coarse textures classified as Popcorn or Tree bark exhibit severe surface irregularities and undercuts that cannot be uniformly coated; these surfaces must be mechanically scarified, planed flat, and resprayed.

Substrate Preparation, Reroofing BUR, and Priming

SPF adheres tenaciously to almost any clean, dry, structural substrate. However, surface contaminants or moisture will cause catastrophic delamination:

Substrate Moisture Constraints

Maximum Moisture Content: Wood and masonry decks must have a moisture content strictly below 8% to 10% . The substrate must be completely dry with zero dew, frost, or condensation.

Moisture Reaction: Applying SPF over damp substrates causes the isocyanate to react with water instead of the polyol, producing carbon dioxide ( C O 2 CO_2 C O 2 ​ ) gas. This reaction creates severe pinholing, surface bubbles, blisters, and total adhesion failure.

Reroofing over Existing Built-Up Roofs (BUR)

When applying SPF over an existing gravel-surfaced built-up roof (recover application):

Gravel Removal: All loose aggregate and embedded gravel must be completely removed using mechanical spudders and high-powered industrial roof vacuums down to the smooth flood coat or top ply.

Moisture Survey: An infrared or nuclear moisture survey must identify wet insulation. All wet areas must be cut out and replaced with dry, matched materials.

Surface Cleaning: The surface must be power-swept or air-blown free of all dust and dirt.

Priming Requirements

Metal Substrates (Steel, Aluminum): Must be power-washed to remove manufacturing oils and treated with a rust-inhibitive wash primer or epoxy primer to ensure adhesion and stop oxidation.

Concrete and Masonry: Require a high-penetration acrylic or epoxy primer to bind surface laitance and concrete dusting.

Asphalt Substrates: Smooth BUR or aged modified bitumen requires an asphalt primer ( ASTM D41 ) or quick-drying water-based acrylic primer to lock down residual bitumen dust.

Liquid-Applied Protective Coatings: Types and Formulations

SPF has zero natural resistance to solar ultraviolet (UV) radiation. Unprotected foam exposed to sunlight begins degrading within 24 to 72 hours, breaking down at a rate of 1/16 to 1/8 inch per year into an orange-brown, chalky, friable dust. An elastomeric roof coating must be applied over the entire foam surface.

Coating Chemistry Polymer Base Solids by Volume Ponding Water Resistance UV & Weather Stability Tensile & Puncture Resistance Primary Applications & Trade Notes

Acrylic (Elastomeric) 100% Acrylic water-based latex 50% – 65% Poor (re-emulsifies under prolonged submersion > 48 hrs) Excellent UV resistance; high solar reflectance Moderate (300–400 psi); requires regular maintenance Standard positive-slope commercial roofs; breathable, cost-effective; clean equipment with water

Silicone Moisture-cure silicone polymer 70% – 95% Outstanding (will not re-emulsify or degrade in standing water) Superior UV stability; inert to extreme heat and ozone Low tear strength (150–250 psi); easily gouged by bird pecks or foot traffic Roofs with flat slopes or minor ponding depressions; requires specialized silicone primer for recoating

Polyurethane (Urethane) Single-part moisture cure or 2-part aliphatic/aromatic 65% – 85% Good to Excellent (handles intermittent ponding) Aromatic requires aliphatic UV topcoat; aliphatic has superior UV Exceptional tensile strength (> 1,000 psi) and impact resistance Heavy foot-traffic corridors, high-hail risk regions, rooftop plant decks; applied as durable base coat

Dry Film Thickness (DFT) vs. Wet Film Thickness (WFT)

Roof coatings are specified in mils (1 mil = 0.001 inch). The roofer measures Wet Film Thickness (WFT) during spray application using a notched wet mil gauge, but the final cured membrane performance depends on the Dry Film Thickness (DFT): DFT = WFT × ( Percent Solids by Volume 100 ) \text{DFT} = \text{WFT} \times \left(\frac{\text{Percent Solids by Volume}}{100}\right) DFT = WFT × ( 100 Percent Solids by Volume ​ ) WFT = DFT ( Percent Solids by Volume 100 ) \text{WFT} = \frac{\text{DFT}}{\left(\frac{\text{Percent Solids by Volume}}{100}\right)} WFT = ( 100 Percent Solids by Volume ​ ) DFT ​

Spreading Rate and Mil Relationships

One gallon of liquid coating spread over 100 square feet (1 square) yields a theoretical wet film thickness of 16 mils ( 16.04 mils 16.04\text{ mils} 16.04 mils exactly).

Field Calculation Example: A specification requires a minimum finished dry film thickness of 24 dry mils using an acrylic coating that contains 60% solids by volume . WFT = 24 mils 0.60 = 40 wet mils \text{WFT} = \frac{24\text{ mils}}{0.60} = 40\text{ wet mils} WFT = 0.60 24 mils ​ = 40 wet mils Application Rate = 40 mils 16 mils/gal/sq = 2.5 gallons per square \text{Application Rate} = \frac{40\text{ mils}}{16\text{ mils/gal/sq}} = 2.5\text{ gallons per square} Application Rate = 16 mils/gal/sq 40 mils ​ = 2.5 gallons per square

Contrasting Multi-Coat Application: Coatings must be applied in a minimum of two separate coats of contrasting colors (e.g., gray base coat followed by white top coat). This ensures complete coverage, allows visual verification of pinhole-free application, and prevents thin spots.

Ceramic Granule Embedment

To protect the elastomeric coating from physical wear, bird pecks, and foot traffic, mineral granules are broadcast into the wet top coat:

Specification: ASTM D451 ceramic-coated roofing granules (#11 roofing grade).

Application Rate: 30 to 40 pounds per square broadcast uniformly into the uncured top coat at a minimum rate of 10 to 12 wet mils.

Benefits: Provides mechanical impact resistance against hail, increases surface traction for worker safety, and improves the assembly's UL 790 / ASTM E108 Class A fire rating.

California Energy Code (Title 24) Cool Roof Compliance

Under the California Building Code and Title 24 Part 6 (California Energy Code), low-slope nonresidential roofs and reroofing projects must meet strict "Cool Roof" radiative properties verified by the Cool Roof Rating Council (CRRC):

Aged Solar Reflectance: Minimum 0.63 (3-year aged rating).

Thermal Emittance: Minimum 0.75 (3-year aged rating).

Solar Reflectance Index (SRI): Alternatively, a minimum aged SRI of 75 (or initial SRI ≥ 82) satisfies Title 24 compliance. Bright white acrylic and silicone roof coatings routinely exceed an SRI of 100, significantly reducing rooftop temperatures and cooling loads in California climate zones.

Loading diagram... SPF Application, Lift Control, and Protective Coating Workflow