Study guide

3.1 Built-Up Roofing (BUR) Systems, Felts, and Hot Bitumen Application

California C-39 Roofing Contractor Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Planning, Codes, and Roofing Estimating

1.1 California Building Codes, Title 24 Energy Standards, and Plan Reading 1.2 Roof Geometry, Area Calculations, and Pitch Multipliers 1.3 Material Takeoffs, Squares, and Waste Calculations 1.4 Roof System Selection, Specifications, Permits, and Project Scheduling 1.5 Labor Production Rates, Overhead, Profit, and Roofing Bid Pricing

2 Chapter 2: Job Site Preparation and Substrate Remediation

2.1 Jobsite Protection, Material Staging, and Temporary Weatherproofing 2.2 Tear-Off Procedures, Overlay Limitations, and Hazardous Materials 2.3 Roof Deck Inspection, Substrate Preparation, and Sheathing Repairs

3 Chapter 3: Low-Slope Roof Systems — Built-Up, Modified Bitumen, and Single-Ply

3.1 Built-Up Roofing (BUR) Systems, Felts, and Hot Bitumen Application 3.2 Modified Bitumen Membrane Systems (APP vs. SBS) and Installation 3.3 Single-Ply Roofing Membranes (TPO, PVC, EPDM) and Seaming Methods

4 Chapter 4: Low-Slope Roof Systems — SPF, Coatings, Flashings, and Maintenance

4.1 Spray Polyurethane Foam (SPF) and Liquid-Applied Protective Coatings 4.2 Low-Slope Drainage, Perimeters, Penetration Flashings, and Scuppers 4.3 Low-Slope Diagnostics, Blister Repairs, and Preventative Maintenance

5 Chapter 5: Steep-Slope Roofing — Flashing, Underlayment, and Ventilation

5.1 Steep-Slope Underlayments, Felt Grades, and Self-Adhering Ice/Water Barriers 5.2 Flashing Details: Valleys, Drip Edges, Step Flashing, Aprons, and Crickets 5.3 Attic and Roof Ventilation: NFVA Requirements, Vent Types, and Airflow Balance

6 Chapter 6: Steep-Slope Roofing — Materials, Installation, and Repair

6.1 Asphalt Shingle Installation, Fastening Patterns, and Wind/Slope Requirements 6.2 Concrete and Clay Tile Roofing (TRI Standards, Battens, and Fastening) 6.3 Standing Seam Metal Panels, Wood Shakes, Slate, and Steep-Slope Repairs 6.4 Steep-Slope Leak Diagnosis, Targeted Repairs, and the Repair-or-Replace Decision

7 Chapter 7: California Roofing Safety — Cal/OSHA, Fall Protection, and Hazards

7.1 Cal/OSHA Fall Protection: Residential Roofing (§1731), Roof Hazards (§1730), and PFAS 7.2 Cal/OSHA Ladder Safety, Scaffold Erection, and Power Line Clearance 7.3 Heat Illness Prevention (CCR §3395), Hot Asphalt Safety, and Personnel PPE 7.4 Injury and Illness Prevention Program, Safety Training, Recordkeeping, and Cal/OSHA Reporting 7.5 Hazard Communication, Asbestos, Lead, and Silica: Managing Unknown Materials

8 Chapter 8: CSLB Licensing Law and Business Organization

8.1 CSLB Licensing Classifications, Bond Requirements, and License Law 8.2 Business Entity Choice, Personnel of Record, and Qualifier Responsibilities 8.3 Advertising Rules, Home Improvement Salespersons, and Subcontracting

9 Chapter 9: Business Finances, Financial Reporting, and Taxes

9.1 Cash Management, Job Costing, and Working Capital 9.2 Budgeting, Business Planning, and Break-Even Analysis 9.3 Financial Reporting: Statements, Accounting Methods, and Key Ratios 9.4 Federal and California Taxes for Roofing Contractors

10 Chapter 10: Employment Requirements, Supervision, and Payroll

10.1 Hiring: Worker Classification, Verification, and New-Hire Reporting 10.2 Supervising and Training Employees 10.3 Performance Evaluation, Personnel Records, and Termination 10.4 California Payroll: Wages, Overtime, Meal and Rest Periods, and Deposits

11 Chapter 11: Insurance, Bonds, and Payment Remedies

11.1 Workers' Compensation Insurance for California Roofing Contractors 11.2 Business Insurance and Surety Bonds 11.3 California Mechanics Lien Law, 20-Day Preliminary Notices, and Lien Waivers

12 Chapter 12: Contract Requirements, Bidding, and Project Execution

12.1 California Roofing Contracts, Home Improvement Law (B&P §7159), and Warranties 12.2 Bidding Practices, Bid Documents, and Competitive Bidding Law 12.3 Job Cost Control and Change Order Management 12.4 Project Organization, Scheduling, and Documentation 12.5 Payments: Progress Payments, Retention, and California Prompt Payment Law

13 Chapter 13: Public Works Roofing Projects

13.1 Prevailing Wage, DIR Registration, and Certified Payroll 13.2 Public Works Bonding and Insurance Requirements

3.1 Built-Up Roofing (BUR) Systems, Felts, and Hot Bitumen Application

Key Takeaways Explain This Topic AI

Built-Up Roofing (BUR) relies on multiple plies of reinforcing felts laminated with alternating moppings of hot asphalt or coal tar pitch to create a redundant, monolithic waterproofing barrier.

Asphalt grades (ASTM D312 Types I–IV) are classified by softening point and slope suitability, ranging from Type I (135°F–151°F, dead flat) to Type IV (210°F–225°F, steep slopes and vertical flashings up to 6:12).

Proper application viscosity requires heating bitumen to its Equiviscous Temperature (EVT) ± 25°F at the point of application, while strictly staying at least 25°F below the material's Flash Point (FP).

Standard 36-inch wide ply rolls require precise starter cuts (12", 24", 36" for 3-ply; 9", 18", 27", 36" for 4-ply) to establish uniform shingle exposures (11.3" for 3-ply, 8.5" for 4-ply) and prevent overlapping joints.

Protective aggregate surfacing requires a heavy bitumen flood coat of 50–60 lbs/sq of asphalt into which 400 lbs/sq of roofing gravel or 300 lbs/sq of slag is embedded.

Last updated: September 2026

Built-Up Roofing (BUR) Systems, Felts, and Hot Bitumen Application

Trade Overview: Built-Up Roofing (BUR) is a traditional multi-ply low-slope roof assembly constructed by laminating alternating layers of reinforcing felts with hot bitumen. For California C-39 roofing contractors, mastering BUR requires understanding material standards (ASTM D2178, D312, D450), temperature-viscosity relationships, shingling layout geometry, kettle safety, and surfacing requirements under California Building Code Chapter 15.

Anatomical Components of a Built-Up Roof Assembly

A conventional BUR system consists of four primary layered components:

Substrate and Base Sheets: Nailable decks (plywood/OSB) require a base sheet to isolate bitumen from joints. Non-nailable decks (concrete, rigid polyiso) accept mechanically fastened or adhered sheets. Standard specifications include ASTM D2626 (organic base sheet), ASTM D4601 (asphalt-coated fiberglass base sheet), and ASTM D4897 (venting base sheet with underside mineral granules to relieve vapor pressure over lightweight concrete).

Reinforcing Ply Felts: Modern BUR utilizes asphalt-impregnated glass fiber felts compliant with ASTM D2178 , which offer superior tensile stability and porosity over historical organic felts ( ASTM D226 ):

Type IV: Minimum longitudinal breaking strength of 44 lbf/in .

Type VI: Heavy-duty ply sheet with minimum longitudinal breaking strength of 60 lbf/in for high-stress assemblies.

Bituminous Moppings: Molten bitumen bonds plies and provides primary waterproofing. Hot asphalt ( ASTM D312 ) is mopped at 20 to 25 lbs per square (100 sq ft) ±15%. Coal tar pitch ( ASTM D450 Type I ) is applied at 25 to 30 lbs per square .

Protective Surfacing: Protects plies from solar ultraviolet radiation, foot traffic, and thermal shock using aggregate embedded in a flood coat, an ASTM D3909 mineral-surfaced cap sheet (75–80 lbs/sq), or Title 24 cool roof coatings.

Asphalt Grades and Bitumen Characteristics

ASTM D312 establishes four asphalt grades based on softening point and slope suitability:

Bitumen Type ASTM Standard Softening Point Max Slope EVT Range Primary Field Applications

Type I (Dead Flat) ASTM D312 135°F – 151°F 1/4 in/ft (2%) 350°F – 400°F Dead-flat roofs, heavy ponding areas, subterranean waterproofing

Type II (Flat) ASTM D312 158°F – 176°F 1/2 in/ft (4%) 375°F – 425°F Low-slope roofs with moderate drainage; interply mopping

Type III (Steep) ASTM D312 185°F – 205°F 3 in/ft (25%) 400°F – 450°F Standard commercial low-slope ply mopping and cap sheets

Type IV (Special Steep) ASTM D312 210°F – 225°F 6 in/ft (50%) 425°F – 475°F Vertical flashings, parapet walls, and steep roof inclines

Coal Tar Pitch (Type I) ASTM D450 126°F – 140°F 1/4 in/ft 330°F – 380°F Flat decks requiring superior ponding resistance and self-healing

Coal Tar Pitch vs. Asphalt: Coal tar pitch has exceptional resistance to standing water and exhibits cold-flow self-healing. However, its low softening point (126°F–140°F) restricts it to slopes <= 1/4 in/ft. Pitch volatiles also cause skin and eye burns under sunlight, requiring specialized PPE.

Temperature Dynamics: EVT, Flash Point, and Kettle Safety

Temperature control directly dictates bitumen viscosity, bonding strength, and fire safety:

Equiviscous Temperature (EVT): The temperature at which bitumen achieves proper viscosity for spreading:

Hand Mopping Viscosity: Target is 125 centistokes (cSt) .

Mechanical Spreader Viscosity: Target is 75 centistokes (cSt) (typically 20°F–25°F higher).

Application Tolerance: Bitumen must reach the deck within EVT ± 25°F . Applying below EVT produces heavy moppings and trapped air blisters; applying above EVT results in thin, starved interply moppings.

Flash Point (FP) vs. Finished Blowing Temperature (FBT):

Flash Point: The temperature at which open vapors flash in air. Kettles must operate at least 25°F to 50°F below the Flash Point .

Finished Blowing Temperature: The maximum manufacturing refinery temperature. Heating above FBT for over 3 to 4 hours causes "fall-in," degrading asphaltenes and permanently lowering the softening point.

Maximum Heating Limit: Typically 475°F–500°F for asphalt and 400°F–425°F for coal tar pitch.

Shingling Ply Felts: Starter Cuts and Exposure Geometry

BUR felts are applied shingle-fashion perpendicular to slope so laps shed water. On slopes exceeding 1/2 in/ft, plies run parallel to slope and are blind-nailed to prevent slippage.

Starter Cuts and Exposure Calculations (36-Inch Rolls)

To avoid thick ridge build-ups at the eave, starter plies are cut into proportional widths:

2-Ply Assembly: Starter cut to 18 inches, followed by full 36-inch rolls. Exposure is 17 inches with a 19-inch overlap.

3-Ply Assembly:

  • 1st Starter Ply: 12 inches wide (1/3 width)
  • 2nd Starter Ply: 24 inches wide (2/3 width)
  • 3rd Ply and Subsequent: Full 36-inch rolls

Exposure: ( 36 " − 2 " ) / 3 = 11.3 " (36" - 2") / 3 = 11.3" ( 36" − 2" ) /3 = 11.3" exposure (commonly marked at 11-1/3" to 12" lines) with a 24.6-inch overlap.

4-Ply Assembly:

  • 1st Starter Ply: 9 inches wide (1/4 width)
  • 2nd Starter Ply: 18 inches wide (2/4 width)
  • 3rd Starter Ply: 27 inches wide (3/4 width)
  • 4th Ply and Subsequent: Full 36-inch rolls

Exposure: ( 36 " − 2 " ) / 4 = 8.5 " (36" - 2") / 4 = 8.5" ( 36" − 2" ) /4 = 8.5" exposure with a 27.5-inch overlap, guaranteeing four continuous plies throughout.

End Laps and Brooming: End laps must be a minimum of 4 to 6 inches and staggered at least 3 feet between adjacent courses. Felts must be broomed in immediately behind the mop to eliminate air pockets and prevent blisters.

Surfacing and Aggregate Embedment Rates

Surfacing protects the bitumen plies from UV degradation and delivers ASTM E108 Class A fire resistance:

Bitumen Flood Coat: Applied at 50 to 60 lbs/sq for asphalt or 60 to 70 lbs/sq for coal tar pitch.

Aggregate Embedment (ASTM D1863):

Roofing Gravel: 400 lbs per square embedded while the flood coat is hot.

Crushed Slag: 300 lbs per square (reduced weight due to angular porosity and lower density).

Cap Sheet Surfacing: An ASTM D3909 mineral-surfaced cap sheet (75–80 lbs/sq) embedded into 20–25 lbs/sq hot asphalt with 2-inch side laps and 6-inch end laps.

California Title 24: Smooth-surfaced assemblies require an approved cool roof reflective coating meeting Title 24 Solar Reflectance Index (SRI) minimums.

Loading diagram... Built-Up Roof Assembly Cross-Section and 4-Ply Sequence