Study guide

1.1 California Building Codes, Title 24 Energy Standards, and Plan Reading

California C-39 Roofing Contractor Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Planning, Codes, and Roofing Estimating

1.1 California Building Codes, Title 24 Energy Standards, and Plan Reading 1.2 Roof Geometry, Area Calculations, and Pitch Multipliers 1.3 Material Takeoffs, Squares, and Waste Calculations 1.4 Roof System Selection, Specifications, Permits, and Project Scheduling 1.5 Labor Production Rates, Overhead, Profit, and Roofing Bid Pricing

2 Chapter 2: Job Site Preparation and Substrate Remediation

2.1 Jobsite Protection, Material Staging, and Temporary Weatherproofing 2.2 Tear-Off Procedures, Overlay Limitations, and Hazardous Materials 2.3 Roof Deck Inspection, Substrate Preparation, and Sheathing Repairs

3 Chapter 3: Low-Slope Roof Systems — Built-Up, Modified Bitumen, and Single-Ply

3.1 Built-Up Roofing (BUR) Systems, Felts, and Hot Bitumen Application 3.2 Modified Bitumen Membrane Systems (APP vs. SBS) and Installation 3.3 Single-Ply Roofing Membranes (TPO, PVC, EPDM) and Seaming Methods

4 Chapter 4: Low-Slope Roof Systems — SPF, Coatings, Flashings, and Maintenance

4.1 Spray Polyurethane Foam (SPF) and Liquid-Applied Protective Coatings 4.2 Low-Slope Drainage, Perimeters, Penetration Flashings, and Scuppers 4.3 Low-Slope Diagnostics, Blister Repairs, and Preventative Maintenance

5 Chapter 5: Steep-Slope Roofing — Flashing, Underlayment, and Ventilation

5.1 Steep-Slope Underlayments, Felt Grades, and Self-Adhering Ice/Water Barriers 5.2 Flashing Details: Valleys, Drip Edges, Step Flashing, Aprons, and Crickets 5.3 Attic and Roof Ventilation: NFVA Requirements, Vent Types, and Airflow Balance

6 Chapter 6: Steep-Slope Roofing — Materials, Installation, and Repair

6.1 Asphalt Shingle Installation, Fastening Patterns, and Wind/Slope Requirements 6.2 Concrete and Clay Tile Roofing (TRI Standards, Battens, and Fastening) 6.3 Standing Seam Metal Panels, Wood Shakes, Slate, and Steep-Slope Repairs 6.4 Steep-Slope Leak Diagnosis, Targeted Repairs, and the Repair-or-Replace Decision

7 Chapter 7: California Roofing Safety — Cal/OSHA, Fall Protection, and Hazards

7.1 Cal/OSHA Fall Protection: Residential Roofing (§1731), Roof Hazards (§1730), and PFAS 7.2 Cal/OSHA Ladder Safety, Scaffold Erection, and Power Line Clearance 7.3 Heat Illness Prevention (CCR §3395), Hot Asphalt Safety, and Personnel PPE 7.4 Injury and Illness Prevention Program, Safety Training, Recordkeeping, and Cal/OSHA Reporting 7.5 Hazard Communication, Asbestos, Lead, and Silica: Managing Unknown Materials

8 Chapter 8: CSLB Licensing Law and Business Organization

8.1 CSLB Licensing Classifications, Bond Requirements, and License Law 8.2 Business Entity Choice, Personnel of Record, and Qualifier Responsibilities 8.3 Advertising Rules, Home Improvement Salespersons, and Subcontracting

9 Chapter 9: Business Finances, Financial Reporting, and Taxes

9.1 Cash Management, Job Costing, and Working Capital 9.2 Budgeting, Business Planning, and Break-Even Analysis 9.3 Financial Reporting: Statements, Accounting Methods, and Key Ratios 9.4 Federal and California Taxes for Roofing Contractors

10 Chapter 10: Employment Requirements, Supervision, and Payroll

10.1 Hiring: Worker Classification, Verification, and New-Hire Reporting 10.2 Supervising and Training Employees 10.3 Performance Evaluation, Personnel Records, and Termination 10.4 California Payroll: Wages, Overtime, Meal and Rest Periods, and Deposits

11 Chapter 11: Insurance, Bonds, and Payment Remedies

11.1 Workers' Compensation Insurance for California Roofing Contractors 11.2 Business Insurance and Surety Bonds 11.3 California Mechanics Lien Law, 20-Day Preliminary Notices, and Lien Waivers

12 Chapter 12: Contract Requirements, Bidding, and Project Execution

12.1 California Roofing Contracts, Home Improvement Law (B&P §7159), and Warranties 12.2 Bidding Practices, Bid Documents, and Competitive Bidding Law 12.3 Job Cost Control and Change Order Management 12.4 Project Organization, Scheduling, and Documentation 12.5 Payments: Progress Payments, Retention, and California Prompt Payment Law

13 Chapter 13: Public Works Roofing Projects

13.1 Prevailing Wage, DIR Registration, and Certified Payroll 13.2 Public Works Bonding and Insurance Requirements

1.1 California Building Codes, Title 24 Energy Standards, and Plan Reading

Key Takeaways Explain This Topic AI

The California Building Code (Title 24 Part 2, Chapter 15) mandates Class A fire-rated roof assemblies for all structures located within designated High Fire Severity Zones.

California Energy Code Title 24 Part 6 requires low-slope commercial roofs to meet a minimum 3-year aged solar reflectance of 0.63 and thermal emittance of 0.75, or an aged Solar Reflectance Index (SRI) of 75.

Under CSLB C-39 classification (CCR Title 16, § 832.39), licensed roofing contractors install weatherproofing systems, flashing, and insulation, requiring mandatory deck nail, pre-roofing (dry-in), and final inspections by local building officials.

Secondary overflow roof drains or emergency scuppers per CBC § 1502 are mandatory on parapet-enclosed roofs, positioned at least 2 inches above primary drains with independent drainage piping.

Last updated: September 2026

California Building Codes, Title 24 Energy Standards, and Plan Reading

Navigating California's building codes is essential for professional practice under the California Contractors State License Board (CSLB). Roofing installations are governed by the California Building Standards Code (Title 24 CCR) : commercial projects fall under the 2022 California Building Code (CBC, Title 24, Part 2) , one- and two-family dwellings under the 2022 California Residential Code (CRC, Title 24, Part 2.5) , and energy conservation under the California Energy Code (Title 24, Part 6) .

1. CSLB C-39 Roofing Contractor Scope of Work

Under California Code of Regulations (CCR) Title 16, Division 8, Section 832.39 , the CSLB establishes the C-39 Roofing Contractor classification:

Authorized Scope : Installing weatherproofing materials including asphalt shingles, slate, tile, shakes, wood shingles, built-up roofing (BUR), modified bitumen, single-ply systems, liquid-applied roof coatings, spray polyurethane foam (SPF), and metal panels.

Accessory Components : Installing roof deck insulation, damp-proofing, and related architectural sheet metal—such as gravel stops, copings, valleys, gutters, downspouts, and flashing assemblies connected to the roof system.

Statutory Limits : A C-39 licensee may contract only within the field and scope the Board has classified it for (B&P Code § 7059). Taking on work outside the roofing classification — structural truss redesign, framing a new roof deck, or a multi-trade remodel — is a separate cause for disciplinary action under B&P Code § 7117.6 and must be subcontracted to an appropriately licensed contractor.

2. California Building Code (CBC) Chapter 15 & CRC Chapter 9

Chapter 15 of the CBC and Chapter 9 of the CRC regulate weather protection, fire resistance, and structural attachment.

Fire Classifications (CBC § 1505 & CRC § R902)

Roof coverings are classified as Class A, B, or C tested under ASTM E108 or UL 790 :

Class A : Highest fire resistance (flame spread index ≤ \le ≤ 25), protecting against severe fire exposures.

Class B & C : Moderate and light fire exposures.

Wildland-Urban Interface (WUI) Mandate : Under CBC Chapter 7A and CRC § R902.1, structures in designated Very High Fire Hazard Severity Zones (VHFHSZ) mandate Class A roof assemblies . Wood shakes must be factory-impregnated with fire retardants and listed as Class A systems.

Slope Classifications and Roof Drainage (CBC § 1502 & § 1507)

Steep-Slope Assemblies (> 2:12) : Asphalt shingles require a minimum slope of 2:12. For slopes from 2:12 to less than 4:12, a low-slope double underlayment (two plies of ASTM D226 felt lapped 19 inches) or self-adhering modified bitumen underlayment per CRC § R905.2.7 is mandatory. Slopes ≥ \ge ≥ 4:12 permit standard single-layer underlayment.

Low-Slope Assemblies ( ≤ \le ≤ 2:12) : BUR, modified bitumen, and single-ply membranes require a minimum finished slope of 1/4 inch per foot (2% slope) toward positive drainage points (CBC § 1507.10.1). Coal-tar BUR permits a minimum slope of 1/8:12 (1%).

Secondary (Emergency) Overflow Drainage (CBC § 1502.2) : Where a parapet or other perimeter construction can trap water if the primary drains clog, an independent secondary (emergency overflow) drain or scupper system is required. Secondary drains must discharge to an approved exterior location and must not be tied into the interior primary drain piping. The overflow inlet flow line is set 2 inches above the low point of the roof, and overflow scuppers are not less than 4 inches in open height.

3. Title 24, Part 6: California Energy Code (Cool Roofs)

Title 24 Part 6 mandates certified "Cool Roof" products rated by the Cool Roof Rating Council (CRRC) across California's 16 Climate Zones :

Solar Reflectance : Fraction of solar energy reflected from the roof (initial and 3-year aged ).

Thermal Emittance : Ability of the surface to radiate absorbed heat away from the building.

Solar Reflectance Index (SRI) : Composite metric calculated per ASTM E1980 .

Prescriptive Requirements (2022 Standards)

Occupancy & Slope Category Climate Zones Minimum 3-Year Aged Reflectance Minimum Thermal Emittance Minimum Aged SRI

  • Nonresidential Low-Slope ( ≤ \le ≤ 2:12) Zones 1–16 0.63 0.75 75
  • Nonresidential Steep-Slope (> 2:12) Zones 2–16 0.20 0.75 16
  • Single-Family Residential Steep-Slope Zones 4, 8–15 0.20 0.75 16
  • Multifamily Residential Low-Slope Zones 1–16 0.63 0.75 75

Exemptions : Residential cool roofs are exempt if the attic contains ≥ \ge ≥ R-38 insulation, an approved radiant barrier is installed, or continuous elevated tile battens provide a 1-inch airspace. Compliance must be certified on form CF2R-ENV-04-E by the C-39 contractor.

4. Architectural Plan Reading and Details

Accurate blueprint interpretation is essential for estimating and code compliance:

Roof Plans : Identify perimeter geometry, ridgelines, hips, valleys, rakes, eaves, roof slopes (pitch triangles), scuppers, and drains.

Crickets and Saddles (CBC § 1503.2 / CRC § R903.2.2) : Chimneys or penetrations more than 30 inches wide measured perpendicular to the slope require a cricket or saddle on the ridge side to deflect drainage around the curb. Cricket coverings must be sheet metal or the same material as the roof covering.

Parapet Walls and Base Flashing : Detail sheets specify a minimum 8-inch vertical base flashing height, sheet metal counterflashing set into masonry reglets, and inward-sloping metal copings.

Drip Edge Flashing (CRC § R905.2.8.5) : Required at eaves and gable rakes for asphalt shingles. Drip edge must extend at least 2 inches onto the deck with a 1/4-inch drip leg. Eave underlayment overlaps the drip edge; rake drip edge installs over underlayment.

5. Permitting and Mandatory Building Inspections

A local building permit is required prior to starting any reroofing project exceeding 100 sq ft (1 square). Standard municipal oversight requires three mandatory inspections:

Deck Nailing / Sheathing Inspection : Conducted after complete tear-off to inspect dry rot, deck thickness, and fastening patterns (e.g., 8d common nails spaced 6 inches on edges and 12 inches in the field).

Pre-Roofing / Dry-In Inspection : Conducted after underlayment, drip edge, valley flashings, and crickets are installed, before covering with shingles or tile.

Final Inspection : Conducted upon complete roof assembly installation, verifying flashings, ventilation, spark arrestors, and CRRC energy labels matching form CF2R-ENV-04-E.

Loading diagram... California Roofing Permitting and Inspection Lifecycle