Study guide
5.1 Steep-Slope Underlayments, Felt Grades, and Self-Adhering Ice/Water Barriers
California C-39 Roofing Contractor Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Planning, Codes, and Roofing Estimating
1.1 California Building Codes, Title 24 Energy Standards, and Plan Reading 1.2 Roof Geometry, Area Calculations, and Pitch Multipliers 1.3 Material Takeoffs, Squares, and Waste Calculations 1.4 Roof System Selection, Specifications, Permits, and Project Scheduling 1.5 Labor Production Rates, Overhead, Profit, and Roofing Bid Pricing
2 Chapter 2: Job Site Preparation and Substrate Remediation
2.1 Jobsite Protection, Material Staging, and Temporary Weatherproofing 2.2 Tear-Off Procedures, Overlay Limitations, and Hazardous Materials 2.3 Roof Deck Inspection, Substrate Preparation, and Sheathing Repairs
3 Chapter 3: Low-Slope Roof Systems — Built-Up, Modified Bitumen, and Single-Ply
3.1 Built-Up Roofing (BUR) Systems, Felts, and Hot Bitumen Application 3.2 Modified Bitumen Membrane Systems (APP vs. SBS) and Installation 3.3 Single-Ply Roofing Membranes (TPO, PVC, EPDM) and Seaming Methods
4 Chapter 4: Low-Slope Roof Systems — SPF, Coatings, Flashings, and Maintenance
4.1 Spray Polyurethane Foam (SPF) and Liquid-Applied Protective Coatings 4.2 Low-Slope Drainage, Perimeters, Penetration Flashings, and Scuppers 4.3 Low-Slope Diagnostics, Blister Repairs, and Preventative Maintenance
5 Chapter 5: Steep-Slope Roofing — Flashing, Underlayment, and Ventilation
5.1 Steep-Slope Underlayments, Felt Grades, and Self-Adhering Ice/Water Barriers 5.2 Flashing Details: Valleys, Drip Edges, Step Flashing, Aprons, and Crickets 5.3 Attic and Roof Ventilation: NFVA Requirements, Vent Types, and Airflow Balance
6 Chapter 6: Steep-Slope Roofing — Materials, Installation, and Repair
6.1 Asphalt Shingle Installation, Fastening Patterns, and Wind/Slope Requirements 6.2 Concrete and Clay Tile Roofing (TRI Standards, Battens, and Fastening) 6.3 Standing Seam Metal Panels, Wood Shakes, Slate, and Steep-Slope Repairs 6.4 Steep-Slope Leak Diagnosis, Targeted Repairs, and the Repair-or-Replace Decision
7 Chapter 7: California Roofing Safety — Cal/OSHA, Fall Protection, and Hazards
7.1 Cal/OSHA Fall Protection: Residential Roofing (§1731), Roof Hazards (§1730), and PFAS 7.2 Cal/OSHA Ladder Safety, Scaffold Erection, and Power Line Clearance 7.3 Heat Illness Prevention (CCR §3395), Hot Asphalt Safety, and Personnel PPE 7.4 Injury and Illness Prevention Program, Safety Training, Recordkeeping, and Cal/OSHA Reporting 7.5 Hazard Communication, Asbestos, Lead, and Silica: Managing Unknown Materials
8 Chapter 8: CSLB Licensing Law and Business Organization
8.1 CSLB Licensing Classifications, Bond Requirements, and License Law 8.2 Business Entity Choice, Personnel of Record, and Qualifier Responsibilities 8.3 Advertising Rules, Home Improvement Salespersons, and Subcontracting
9 Chapter 9: Business Finances, Financial Reporting, and Taxes
9.1 Cash Management, Job Costing, and Working Capital 9.2 Budgeting, Business Planning, and Break-Even Analysis 9.3 Financial Reporting: Statements, Accounting Methods, and Key Ratios 9.4 Federal and California Taxes for Roofing Contractors
10 Chapter 10: Employment Requirements, Supervision, and Payroll
10.1 Hiring: Worker Classification, Verification, and New-Hire Reporting 10.2 Supervising and Training Employees 10.3 Performance Evaluation, Personnel Records, and Termination 10.4 California Payroll: Wages, Overtime, Meal and Rest Periods, and Deposits
11 Chapter 11: Insurance, Bonds, and Payment Remedies
11.1 Workers' Compensation Insurance for California Roofing Contractors 11.2 Business Insurance and Surety Bonds 11.3 California Mechanics Lien Law, 20-Day Preliminary Notices, and Lien Waivers
12 Chapter 12: Contract Requirements, Bidding, and Project Execution
12.1 California Roofing Contracts, Home Improvement Law (B&P §7159), and Warranties 12.2 Bidding Practices, Bid Documents, and Competitive Bidding Law 12.3 Job Cost Control and Change Order Management 12.4 Project Organization, Scheduling, and Documentation 12.5 Payments: Progress Payments, Retention, and California Prompt Payment Law
13 Chapter 13: Public Works Roofing Projects
13.1 Prevailing Wage, DIR Registration, and Certified Payroll 13.2 Public Works Bonding and Insurance Requirements
5.1 Steep-Slope Underlayments, Felt Grades, and Self-Adhering Ice/Water Barriers
Key Takeaways Explain This Topic AI
Asphalt-saturated organic felts (ASTM D226 Type I #15 and Type II #30; ASTM D4869) provide breathable, water-shedding protection, whereas synthetic polymer underlayments (ASTM D8257) offer superior tensile strength, UV exposure durability, and slip resistance.
Under CBC § 1507.2.2 and CRC § R905.2.2, roof slopes from 2:12 to less than 4:12 require a low-slope double-layer underlayment application (19-inch lap) or an ASTM D1970 self-adhering modified bitumen membrane, whereas slopes 4:12 and greater permit standard single-layer underlayment with 2-inch headlaps and 4-inch end laps.
Mechanical attachment requires corrosion-resistant plastic-cap nails or tin-tag steel caps spaced 12 to 24 inches on-center along laps and center fields, preventing tear-out from high winds and worker foot traffic.
In designated California freeze-thaw mountain regions (e.g., Sierra Nevada and high-altitude alpine zones), CBC § 1507.1.2 mandates a self-adhering polymer-modified bitumen ice barrier extending from eave edges to at least 24 inches inside the interior wall line.
Last updated: September 2026
5.1 Steep-Slope Underlayments, Felt Grades, and Self-Adhering Ice/Water Barriers
Quick Answer: Steep-slope roof systems rely on secondary water-shedding underlayments installed directly over the structural deck. On standard slopes (4:12 and greater), the California Residential Code (CRC § R905.1.1) permits a single layer of underlayment with a 2-inch headlap and 4-inch end lap. On low slopes (2:12 to less than 4:12), contractors must install either a double-layer system (a 19-inch starter strip followed by full 36-inch sheets overlapped 19 inches) or a continuous self-adhering polymer-modified bitumen membrane meeting ASTM D1970. In California mountain regions with freeze-thaw cycles and history of ice damming, CBC § 1507.1.2 requires an ice barrier extending from the eave edge to a point at least 24 inches inside the interior wall line.
Underlayment serves as a critical secondary weatherproofing barrier beneath steep-slope roof coverings such as asphalt shingles, clay or concrete tiles, metal panels, and wood shakes. While primary roof coverings shed the vast majority of surface runoff, underlayment protects the timber deck from wind-driven rain, capillary moisture draw, ice dam backups, and incidental condensation. For California C-39 roofing contractors, selecting and fastening the correct underlayment grade in accordance with the California Building Code (CBC Chapter 15) and California Residential Code (CRC Chapter 9) is essential for inspection sign-off and long-term roof integrity.
1. Underlayment Classifications and Material Standards
Roofing underlayments are engineered from three primary material categories, each governed by distinct ASTM manufacturing standards and physical performance metrics.
Asphalt-Saturated Organic Felts
Traditional organic felts are manufactured from cellulose wood fibers or recycled paper rags saturated with waterproofing asphalt. They are classified under two primary standards:
ASTM D226 (Standard Specification for Asphalt-Saturated Organic Felt):
Type I (Commonly designated #15 Felt): Typical minimum net weight of 11.5 to 13 lbs per square (100 sq ft). Used primarily as a lightweight temporary barrier on standard residential slopes.
Type II (Commonly designated #30 Felt): Typical minimum net weight of 26 to 28 lbs per square. Provides greater tear resistance, thicker puncture resistance, and enhanced weatherproofing under heavier coverings such as wood shakes, slate, or architectural laminate shingles.
ASTM D4869 (Liquid Water Transmission Resistance): Evaluates physical liquid water penetration through asphalt felts. Classifications range from Type I to Type IV, with Type IV offering the highest liquid water holdout and breaking strength.
Vapor Permeability: Organic felts are breathable membranes, exhibiting a dry vapor permeance of approximately 5 to 8 perms. Under humid or damp conditions, the cellulose fibers absorb water vapor and expand, increasing permeability up to 30 perms and allowing interior attic moisture to escape.
Synthetic Polymer Underlayments
Synthetic underlayments are manufactured from woven or non-woven polypropylene, polyethylene, or polyolefin polymer matrices. Regulated under ASTM D8257 and ICC-ES Acceptance Criteria AC188 , synthetic membranes have largely superseded organic felts in modern trade practice:
Tensile and Tear Strength: Synthetics exhibit up to 10 to 20 times the tear and tensile resistance of ASTM D226 Type II felt. They do not tear out around fasteners under heavy crew foot traffic.
Moisture Impermeability and Rot Resistance: Synthetics do not absorb water, wrinkle, buckle, or rot when exposed to overnight dew or rain before shingle application.
Weight and Coverage Efficiency: A 10-square roll (1,000 sq ft) of synthetic underlayment weighs approximately 25 to 35 lbs, compared to #30 asphalt felt where five 2-square rolls weigh roughly 250 to 300 lbs total.
UV Exposure Ratings: High-grade synthetics incorporate UV-stabilizing chemical polymers permitting direct solar exposure from 30 days up to 180 days without material breakdown.
Vapor Retarder Profile: Most synthetics are non-breathable (vapor perms < 1.0). When installed over unvented or poorly vented attics, proper ventilation design is critical to avoid trapping deck condensation.
Self-Adhering Polymer-Modified Bitumen Membranes
Self-adhering membranes (often referred to in the trade as "ice and water shield") consist of polymer-modified asphalt (SBS - styrene-butadiene-styrene) laminated to a slip-resistant polymer film or mineral-granule surface, backed with a siliconized release film. Regulated by ASTM D1970 :
Thickness: Minimum membrane thickness of 40 mils (0.040 inches / 1.0 mm).
Self-Sealing Fastener Capabilities: The elastic SBS rubberized asphalt flows around shank penetrations, forming an elastomeric gasket around roofing nails and screws.
Direct Deck Adhesion: Adheres aggressively to clean CDX plywood, OSB, and metal flashing flanges without mechanical fasteners, creating a fully bonded, waterproof, non-shedding barrier.
Installation Temperatures: Must generally be applied at ambient temperatures of 40°F (4.4°C) or higher. Specialized low-temperature formulas permit installation down to 25°F (-4°C).
2. Slope Application Thresholds and Code Mandates
The California Residential Code (CRC § R905.1.1 and § R905.2.2) and California Building Code (CBC § 1507.1.1 and § 1507.2.2) dictate underlayment layering based strictly on roof pitch.
Roof Slope Category Slope Ratio Code Underlayment Mandate (CRC § R905 / CBC § 1507) Permitted Primary Coverings
Prohibited Steep-Slope < 2:12 (< 9.5°) Asphalt shingles and standard steep-slope systems strictly prohibited. Requires low-slope membrane (BUR, Mod-Bit, Single-Ply). Low-slope membranes only
Low Slope (Steep-Slope Assemblies) 2:12 to < 4:12 (9.5° to < 18.4°) Double-Layer Application: 19" starter strip at eaves, followed by full 36" sheets lapped 19" across entire deck, OR continuous self-adhering ASTM D1970 membrane. Asphalt shingles (low-slope application), metal panels
Standard Steep Slope 4:12 and greater (≥ 18.4°) Single-Layer Application: Minimum 2-inch headlap and 4-inch end lap across all successive courses. Asphalt shingles, concrete/clay tile, metal, wood shakes, slate
Double-Layer Application Technique (2:12 to < 4:12)
To construct a code-compliant double-layer underlayment on low slopes:
Apply a 19-inch-wide starter strip of underlayment parallel to the eave along the lowest roof perimeter.
Lay a full 36-inch-wide sheet directly over the starter strip, aligning the bottom edge flush with the eave metal flange.
Apply each subsequent 36-inch sheet overlapping the preceding sheet by exactly 19 inches (a 19-inch headlap leaves 17 inches exposed). This geometry ensures that two full layers of underlayment cover every square inch of the roof deck from eave to ridge.
End laps (vertical joints) must be overlapped a minimum of 6 inches and offset by at least 6 feet between adjoining plies.
3. Fastening Specifications and Mechanical Attachment
Improper fastening is a primary cause of underlayment blowout, water infiltration, and tear-off failures during construction.
Fastener Selection
Plastic-Cap Nails: Corrosion-resistant round plastic caps (minimum 1-inch diameter) molded onto 11- or 12-gauge barbed or ring-shank galvanized nails. The wide plastic head distributes holding pressure across synthetic polymers and lightweight felts, preventing head pull-through.
Tin Tags / Steel Caps: 1-5/8-inch round or square steel plates driven with roofing nails. Required in high-wind zones and under heavy concrete tile underlayments.
Staples: Smooth-wire staples are strictly prohibited by code in high-wind regions and under synthetic membranes, as staples create micro-punctures and lack pull-out resistance.
Fastener Patterns for 36-Inch Underlayment Rolls
Laps: Driven along all horizontal headlaps at 12 inches on-center (reduced to 6 inches o.c. in high-wind exposure zones per CRC Table R905.1.1(1)).
Field / Center Row: Two intermediate center rows staggered at 12 to 24 inches on-center , securing the field against wind uplift.
End Laps: Fastened at 6 inches on-center along the vertical 4-to-6-inch lap.
4. Eave Ice Barriers in California Alpine Climates
In California's mountainous regions—including the Sierra Nevada, Lake Tahoe Basin, Mammoth Lakes, Big Bear, and Mount Shasta—freezing ambient temperatures create severe ice dam hazards.
Ice Dam Mechanics
Heat escaping from living spaces through ceiling framing warms the attic air, heating the roof sheathing. Snow accumulating on the upper roof plane melts and flows downward toward the exterior eaves. Because eaves project beyond the exterior heated wall line, their temperature drops below 32°F (0°C). The runoff refreezes at the cold overhang, forming a solid ice ridge. Trapped runoff ponds behind this ice dam, backing upward beneath shingle laps and penetrating nail holes.
Mandatory Code Protection (CBC § 1507.1.2 & CRC § R905.1.2)
Where local building authorities document a history of ice forming along eaves (generally regions where the average daily January temperature is 25°F [-4°C] or lower):
An ice barrier consisting of an ASTM D1970 self-adhering polymer-modified bitumen membrane must be installed.
Geometry: The membrane must extend from the lowest perimeter edge of the eave to a point at least 24 inches (610 mm) inside the exterior wall line of the heated structure.
On roofs with wide overhangs (e.g., 24-inch soffits on a 6-inch exterior wall), a single 36-inch roll covers only 6 inches inside the wall line ( 36 − 24 − 6 = 6 inches 36 - 24 - 6 = 6\text{ inches} 36 − 24 − 6 = 6 inches ). In such cases, contractors must apply a second course of self-adhering membrane lapped 3 to 4 inches over the first course to achieve the required 24-inch interior margin.