Study guide
7.2 Icing, Fog Types & VLOS Weather Minimums
Transport Canada RPAS Basic Operations Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & Exam Overview
1.1 About the Transport Canada Small Basic Exam 1.2 How to Use This Study Guide & Exam Strategy
2 Chapter 2: Air Law — Regulatory Framework, Certification & Registration
2.1 Regulatory Scope & RPA Weight Categories 2.2 Pilot Certification, Minimum Age & Recency Requirements 2.3 RPA Registration, Marking & Record Keeping
3 Chapter 3: Air Law — Operational Limits, Airspace Buffers & Compliance
3.1 Altitude Limits, Bystander Separation & Right of Way 3.2 Aerodrome Stand-offs, Forest Fires & Special Approvals 3.3 Fitness to Fly, Impairment Rules & Incident Reporting
4 Chapter 4: Airspace Classification & Air Traffic Services
4.1 Canadian Airspace Classes A–G & Uncontrolled Operations 4.2 Special Use Airspace, NOTAMs & NAV CANADA Services
5 Chapter 5: Navigation, Aeronautical Charts & Time
5.1 Aeronautical Charts & the Canada Flight Supplement 5.2 Navigation Fundamentals, Coordinates & UTC Time Conversion
6 Chapter 6: Meteorology — Aviation Weather Reports & Density Altitude
6.1 Decoding METAR and TAF Weather Reports 6.2 Density Altitude & Atmospheric Pressure Effects
7 Chapter 7: Meteorology — Weather Hazards, Turbulence & Visibility
7.1 Thunderstorms, Wind Shear & Turbulence 7.2 Icing, Fog Types & VLOS Weather Minimums 7.3 Wind, Local Effects & Low-Level Cloud Recognition
8 Chapter 8: RPAS Systems, Power Plants & Fail-Safes
8.1 RPA Airframes, Propulsion & Electrical Systems 8.2 LiPo Battery Care, Charging & Cold-Weather Operations 8.3 Fuel Systems, Launch & Recovery Systems, Payloads & Maintenance Records
9 Chapter 9: C2 Link, Avionics & Theory of Flight
9.1 Command & Control (C2), Sensors & Fail-Safe Modes 9.2 Aerodynamics & Four Forces of Flight 9.3 Flight Instruments: Magnetic Compass, Altimeter, Airspeed Indicator & IMU 9.4 Airframe Configurations, Stability & Flight Controls
10 Chapter 10: Flight Operations, Planning & Risk Management
10.1 Pilot-in-Command Duties, SOPs & Checklists 10.2 Site Survey, Environmental Analysis & Hazard Mitigation
11 Chapter 11: Weight & Balance, Emergencies & Night Operations
11.1 Weight & Balance, Center of Gravity & Performance 11.2 Emergency Procedures, Flyaways & Night Flight
12 Chapter 12: Human Factors & Aeronautical Radiotelephony
12.1 Human Performance, IMSAFE & Crew Resource Management 12.2 Visual Scanning, Visual Observers & Radiotelephony Phraseology 12.3 Hearing, Illusions, the Operating Environment & Operating Pressures
7.2 Icing, Fog Types & VLOS Weather Minimums
Key Takeaways Explain This Topic AI
Under CAR 901.35, it is strictly prohibited to take off or conduct a flight with frost, ice, or snow adhering to any critical surface of an RPA, embodying the 'clean aircraft concept'.
Structural and propeller icing occurs when visible atmospheric moisture is present and temperatures range between 0°C and -10°C (with severe risk extending down to -20°C).
Clear ice forms from large supercooled droplets that spread before freezing, creating a heavy, dense, transparent glaze that severely distorts airfoils; rime ice forms instantly from small droplets, creating a rough, milky, brittle accumulation.
Radiation fog forms on calm, clear nights via terrestrial radiational cooling; advection fog forms when warm, moist air blows over a cold surface and can persist under moderate to strong coastal winds.
Cloud base AGL can be estimated using the dew point spread formula: Cloud Base (ft AGL) ≈ [(Temperature - Dew Point in °C) / 2.5] × 1,000, which in turn sets the practical ceiling you can use while still keeping the aircraft in visual line-of-sight under CAR 901.11 and CAR 901.34(1)(b).
Last updated: September 2026
Icing, Fog Types & VLOS Weather Minimums
Quick Summary: Low temperatures and atmospheric moisture present severe risks to remotely piloted aircraft operations. Under CAR 901.35 , taking off with frost, ice, or snow adhering to critical surfaces is strictly prohibited. In-flight structural and propeller icing degrades lift, increases motor current draw, and triggers aerodynamic stalls. Concurrently, radiation , advection , upslope , and frontal fog can quickly obliterate visual line-of-sight ( VLOS ). RPAS pilots must use temperature-dew point spread calculations to estimate convective cloud bases and keep the aircraft in continuous visual line-of-sight as CAR 901.11 and CAR 901.34(1)(b) require.
Operating an RPA in Canada requires mastering cold-weather aerodynamics and visual visibility limits. Small drones are disproportionately susceptible to frozen moisture. Unlike commercial airliners equipped with heated airfoils or pneumatic boots, small RPAS have no de-icing mechanisms. Even a microscopic layer of frost or ice on rapidly spinning propeller blades destroys airfoil efficiency, leading to uncommanded descents and loss of control.
Structural & Propeller Icing: Physics & Aerodynamic Consequences
Propeller blades are miniature airfoils spinning at 5,000 to 10,000 RPM, making them the most critical and vulnerable component during sub-zero operations.
Formation Conditions
In-flight structural icing requires two simultaneous conditions:
Visible Atmospheric Moisture: Flight through fog, freezing fog, drizzle, rain, wet snow, or clouds.
Sub-Freezing Temperatures: Ambient outside air temperature (OAT) and airframe surface temperatures at or below 0°C . The highest danger zone for rapid ice accumulation is between 0°C and -10°C , with hazards persisting to -20°C .
Aerodynamic Cooling: Air accelerating over the upper camber of spinning propeller blades expands and cools. Propellers can accumulate ice even when ambient air temperature is slightly above freezing (e.g., +1°C to +3°C) if relative humidity is near 100%.
Types of Structural Ice
Ice Type Formation Temperature Physical Characteristics Aerodynamic Hazard Level
Clear Ice 0°C to -5°C (large droplets) Dense, transparent, smooth; freezes slowly as water flows over airfoil Extreme: Heaviest weight; severely alters blade camber; adheres tenaciously
Rime Ice -10°C to -20°C (small droplets) Milky-white, opaque, rough, porous; freezes instantly, trapping air High: Disrupts laminar airflow; increases parasitic drag; creates rough texture
Mixed Ice -5°C to -15°C (variable droplets) Layered, rough blend of clear and rime ice Severe: Rapid accumulation; asymmetrical shedding; high vibration
Aerodynamic and Electrical Impact on RPAS
Lift Collapse & Parasitic Drag: Ice accretion blunts the propeller leading edge, destroying lift generation by up to 30% while increasing parasitic drag by up to 40%.
Violent Motor Vibration: Asymmetrical ice shedding causes severe dynamic imbalance, loosening motor mounts and blurring sensor payloads.
IMU Sensor Failure: High-frequency vibration saturates internal accelerometer damping, causing the flight controller to miscalculate vehicle attitude and trigger erratic control responses or flyaways.
Motor Overheating & Battery Depletion: Brushless DC motors spin at elevated RPM to offset lost lift, drawing heavy amperage from the battery. This accelerates voltage sag and drastically shortens flight endurance.
Frost and Hoar Frost
Hoar frost forms when water vapour sublimates directly into ice crystals on a surface whose temperature is below freezing and below the frost point — typically on a clear, calm night, on an airframe left outside or unloaded from a cold vehicle into humid air. It looks like a light dusting of white crystals and feels like fine sandpaper.
Hoar frost is deceptively dangerous because it adds almost no weight. What it does is roughen the airfoil surface , disrupting the boundary layer so that airflow separates far earlier than it should. On a fixed wing that can raise the stall speed sharply; on a rotor blade it degrades thrust at exactly the moment maximum thrust is required, during lift-off. Frost must be removed, not merely brushed at — and the airframe must be allowed to come up to temperature so the frost does not immediately re-form.
The Clean Aircraft Concept (CAR 901.35)
Transport Canada enforces a strict standard under CAR 901.35 :
CAR 901.35: No person shall conduct a take-off or continue a flight with an RPAS where frost, ice, or snow is adhering to any critical surface of the aircraft.
Critical surfaces include propeller blades, rotor hubs, lifting wings, and control surfaces. Even frost resembling fine sandpaper increases surface roughness sufficiently to trigger an early aerodynamic stall.
Fog Types & Formation Mechanisms
Aeronautically, fog is defined as microscopic water droplets suspended near the surface that reduce prevailing visibility to less than 5/8 statute mile (mist is 5/8 to 6 SM).
1. Radiation Fog
Mechanism: Forms on clear, calm nights (winds < 5 kt) with high relative humidity. The ground loses heat through terrestrial radiational cooling, chilling the adjacent air layer below its dew point.
Setting: Low-lying river valleys, hollows, and prairie basins during autumn and spring.
Dissipation: Typically burns off within hours after sunrise as solar heating warms the ground.
2. Advection Fog
Mechanism: Forms when a warm, humid air mass drifts horizontally over a cold land or water surface, cooling the air to its saturation point from below.
Wind Requirement: Requires moderate winds (5 to 15 knots) to transport moisture and foster vertical mixing.
Locations & Duration: Common along Pacific and Atlantic coasts and the Great Lakes; can persist for days regardless of daytime solar heating.
3. Upslope Fog
Mechanism: Moist air is mechanically forced up sloping terrain (such as the Rocky Mountain foothills or prairie elevations) by prevailing winds, cooling adiabatically to its dew point.
Dissipation: Persists until wind shifts or weakens.
4. Precipitation (Frontal) Fog
Mechanism: Warm rain falls from an overriding warm air mass through cooler, unsaturated surface air. Raindrop evaporation saturates the cold layer.
Setting: Precedes approaching warm fronts with low overcast ceilings.
5. Steam Fog & Ice Fog
Steam Fog: Extremely cold, dry air blows across warmer open water, creating rising vapor wisps.
Ice Fog: Occurs in extreme Arctic cold (below -30°C ); water vapor sublimes directly into suspended ice crystals.
Atmospheric Stability & Inversions
Atmospheric stability dictates vertical air motion, cloud development, turbulence, and visibility:
- Characteristic Stable Air (Shallow Lapse Rate) Unstable Air (Steep Lapse Rate)
- Lapse Rate Drops slowly (< 2°C/1,000 ft) or increases Drops rapidly (> 3°C/1,000 ft)
- Vertical Airflow Suppressed; smooth laminar air Active convective updrafts and downdrafts
- Cloud Formations Stratiform (stratus, fog, continuous layer) Cumuliform (cumulus, towering cumulonimbus)
- Precipitation Steady, continuous light rain or drizzle Showery, intermittent, heavy precipitation
- Visibility Poor to fair; haze, smoke, fog trapped near surface Good to excellent outside of active rain cells
- Temperature Inversions
A temperature inversion occurs when temperature increases with altitude, reversing the normal lapse rate.
Inversion Lid: The warm air layer aloft acts as a lid, trapping fog, dust, and industrial pollutants in a shallow surface layer.
Wind Shear Hazard: Inversions decouple calm surface air from winds aloft. While surface winds may be 0–2 kt, wind speeds directly above the inversion cap (200–400 ft AGL) often reach 25–35 kt, creating severe low-level wind shear.
VLOS Weather Minimums & Cloud Avoidance
Two rules, correctly distinguished, decide whether the weather is legal:
Continuous VLOS (CAR 901.11): The pilot or a visual observer must maintain unaided visual contact with the aircraft at all times.
Weather Must Permit That VLOS (CAR 901.34(1)): The weather at the time of flight must permit operation in accordance with the operating manuals and permit the pilot or visual observer to conduct the entire flight in visual line-of-sight.
Exam Trap: There is no numeric VLOS weather minimum in Part IX. The "ground visibility not less than three miles and clear of cloud" wording in CAR 901.34(3) belongs to BVLOS operations. Flying into cloud or fog is still illegal for a Basic pilot — but the provision it breaks is the VLOS requirement, not a visibility minimum.
Estimating Convective Cloud Base
Pilots can estimate the base of convective clouds above ground level using the surface temperature-dew point spread : Cloud Base (ft AGL) ≈ [ Temperature (°C) − Dew Point (°C) 2.5 ] × 1 , 000 \text{Cloud Base (ft AGL)} \approx \left[ \frac{\text{Temperature (°C)} - \text{Dew Point (°C)}}{2.5} \right] \times 1,000 Cloud Base (ft AGL) ≈ [ 2.5 Temperature (°C) − Dew Point (°C) ] × 1 , 000
Physical Basis: A rising unsaturated air parcel cools at the dry adiabatic lapse rate (~3.0°C/1,000 ft) while its dew point drops (~0.5°C/1,000 ft). The spread converges at 2.5°C per 1,000 feet .
Practical Examples:
Example 1: Temp 20°C, Dew Point 15°C (Spread = 5°C): Cloud Base = ( 5 2.5 ) × 1 , 000 = 2 , 000 ft AGL \text{Cloud Base} = \left(\frac{5}{2.5}\right) \times 1,000 = 2,000 \text{ ft AGL} Cloud Base = ( 2.5 5 ) × 1 , 000 = 2 , 000 ft AGL
Example 2: Temp 6°C, Dew Point 5°C (Spread = 1°C): Cloud Base = ( 1 2.5 ) × 1 , 000 = 400 ft AGL \text{Cloud Base} = \left(\frac{1}{2.5}\right) \times 1,000 = 400 \text{ ft AGL} Cloud Base = ( 2.5 1 ) × 1 , 000 = 400 ft AGL The estimated cloud base sits right at the 400 ft AGL regulatory ceiling, so there is no usable margin: plan well below it to keep the aircraft visible and out of cloud.
Practical Exam Scenarios & Operational Analysis
Scenario 1: Frost on Rotor Blades: A pilot finds fine frost on propeller edges at sunrise. Action: Under CAR 901.35, takeoff is prohibited. Blades must be completely clean and warmed before flight.
Scenario 2: Rolling Coastal Fog: Operating near an ocean inlet, visibility drops from 10 SM to 1/2 SM in 10 minutes under 12-knot winds. Action: Advection fog moves rapidly with wind. The pilot must land immediately to preserve VLOS.
Scenario 3: Winter Morning Temperature Inversion: A drone launches in calm surface air. At 250 ft AGL, it experiences severe buffeting and high wind telemetry warnings. Action: The RPA has penetrated the inversion boundary into strong winds aloft. The pilot should descend and abort the mission.
Scenario 4: High Humidity Near Freezing: Surface weather reports 02/01 (Temp 2°C, Dew Point 1°C) with mist. Telemetry shows rapid current draw and motor vibration after 5 minutes aloft. Action: Aerodynamic cooling on high-speed propellers has caused structural icing. The pilot must initiate an immediate landing.