Study guide

2.1 Hand Tools for Gas Piping and Mechanical Assembly

TSSA Gas Technician 3 G3

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety & Workplace Practices

1.1 Personal Protective Equipment (PPE) & Worksite Hazard Identification 1.2 WHMIS, GHS, Safety Data Sheets (SDS) & Chemical Safety 1.3 Electrical Safety, Lockout/Tagout (LOTO) & Confined Space Awareness

2 Chapter 2: Fasteners, Hand Tools & Power Tools

2.1 Hand Tools for Gas Piping and Mechanical Assembly 2.2 Power Tools, Threading Machines & Mechanical Fasteners

3 Chapter 3: Testing Instruments & Diagnostics

3.1 Pressure Measurement: U-Tube, Inclined & Digital Manometers 3.2 Electrical Multimeters, Combustion Analyzers & Electronic Leak Detectors

4 Chapter 4: Fuel Gas Properties & Combustion Principles

4.1 Chemical & Physical Properties of Natural Gas vs. Propane 4.2 Combustion Chemistry, Flammability Limits & Ignition Temperatures 4.3 Complete vs. Incomplete Combustion, Carbon Monoxide Hazards & Air Requirements

5 Chapter 5: Ontario Acts, Regulations & G.3 Scope of Authority

5.1 Technical Standards and Safety Act & O. Reg. 215/01 Certification 5.2 O. Reg. 211/01, O. Reg. 212/01 & TSSA Code Adoption Documents (CAD) 5.3 Unacceptable Conditions, Warning Notices & Red Tag Procedures

6 Chapter 6: CSA B149 Code Navigation & General Requirements

6.1 CSA B149.1 & CSA B149.2 Scope, Structure & Key Definitions 6.2 General Installation Rules: Instructions, Access, Clearances & Garages (Clause 4)

7 Chapter 7: Introduction to Electricity & Electrical Safety

7.1 Electrical Fundamentals: Ohm's Law, Power & Circuit Configurations 7.2 Line Voltage (120V) vs. Low Voltage (24V), Transformers & Circuit Protection 7.3 Basic Electrical Controls, Switches & Ladder Diagram Schematics

8 Chapter 8: Technical Manuals, Specifications & Architectural Drawings

8.1 Reading Appliance Rating Plates, Certified Manuals & Specifications 8.2 Architectural Blueprints, Mechanical Drawings & Piping Schematics

9 Chapter 9: Customer Relations, Professional Conduct & Documentation

9.1 Professional Communication, Ethics & Customer Service Standards 9.2 Work Orders, Service Documentation & Red Tag Communication

10 Chapter 10: Piping & Tubing Systems: Materials, Joining & Installation

10.1 Piping & Tubing Materials: Steel, Copper, CSST & Plastic 10.2 Pipe Joining Methods: Threading, Flaring, Brazing & Approved Sealants 10.3 Piping Installation: Supports, Hangers, Drip Legs, Dirt Pockets & Valves

11 Chapter 11: Gas Pipe Sizing, Pressure Testing & Purging Procedures

11.1 Gas Pipe & Tubing Sizing Fundamentals (Tables & Pressure Drop) 11.2 Pressure Testing, Leak Testing & the Ontario Test Tag (Clause 6.22) 11.3 Purging Procedures, Safety Protocols & Leak Detection (Clauses 6.23–6.24)

12 Chapter 12: Gas Appliances, Burners & Combustion Air Fundamentals

12.1 Appliance Classifications, Categories (I–IV), Approvals & Clearances 12.2 Atmospheric & Power Burners: Operation, Aeration & Flame Adjustment 12.3 Ignition Systems & Flame Safeguards: Standing Pilot, HSI, DSI, Thermocouples & Flame Rods 12.4 Combustion Air & Basic Venting Requirements (Clause 8)

2.1 Hand Tools for Gas Piping and Mechanical Assembly

Key Takeaways Explain This Topic AI

Pipe wrenches operate via a camming wedging mechanism; force must always be pulled toward the hook jaw open throat to ensure positive grip and prevent tooth slippage or pipe crushing.

The two-wrench technique (holding back) is mandatory on all gas pipe and appliance connections to isolate rotational torque and prevent twisting concealed piping or cracking fragile valve manifolds.

Cutting pipe creates an inward-facing burr that restricts the bore; CSA B149.1 Clause 6.8 requires cutting burrs to be removed (reamed) to prevent added turbulence, pressure drop, and scale entrapment.

Gas flare connections use 45-degree SAE flare fittings; 37-degree JIC hydraulic flares are a different seat angle and must never be mixed with gas flare fittings.

Flared connections rely exclusively on metal-to-metal seating of soft copper against brass; pipe dope, PTFE tape, or lubricants must never be applied to flare faces or threads.

Last updated: October 2026

Hand Tools for Gas Piping and Mechanical Assembly

Under Ontario Regulation 215/01 and the CSA B149.1 Natural Gas and Propane Installation Code , a Gas Technician 3 (G3) must assemble gas piping and tubing systems that remain permanently gastight. Selecting the proper trade hand tools and applying correct mechanical techniques prevents leaks, component damage, and catastrophic gas hazards.

1. Pipe Wrenches: Mechanics, Direction of Force & Sizing

The straight pipe wrench (Stillson pattern) is designed to grip unmachined cylindrical steel pipe, such as Schedule 40 black iron.

Anatomy and Camming Action

A pipe wrench comprises four core parts:

Heel Jaw: A hardened steel, serrated jaw permanently pinned into the handle housing.

Hook Jaw: A floating forged-steel upper jaw that pivots within the housing frame.

Knurled Nut: An adjustment ring that sets jaw opening capacity.

Spring Mechanism: Internal leaf springs that allow the hook jaw to float and tilt under load.

The tool operates via a mechanical camming wedge action . As torque is applied, the floating hook jaw tilts inward toward the fixed heel jaw, driving the serrated teeth deeper into the pipe circumference.

Direction of Force: The Open Throat Rule

Force must always be pulled toward the open throat of the hook jaw . Pulling toward the throat forces the floating jaw inward, increasing bite as torque rises.

Conversely, pushing a pipe wrench away from the open throat is dangerous . Pushing causes the hook jaw to pivot outward, releasing its grip. The teeth slip across the metal, rounding the pipe fitting, stripping jaw teeth, and risking severe hand and knuckle injuries. Furthermore, pushing places severe cantilever stress on the hook jaw shank, which can snap the forged steel.

Warning

Never push a pipe wrench, and never use a cheater bar (pipe extension) over the handle. Cheater bars multiply torque beyond rated yield limits, causing sudden handle fractures, stripped threads, or crushed fittings. Use a larger wrench when higher torque is required.

Sizing Guidelines

Nominal Pipe Size (NPS) Wrench Size Primary Trade Application

3 / 8 ” 3/8\text{''} 3/8 ” to 1 / 2 ” 1/2\text{''} 1/2 ” 10-inch ( 250 mm 250\text{ mm} 250 mm ) Appliance drops, pilot tubing manifolds, gas control trim

3 / 4 ” 3/4\text{''} 3/4 ” to 1 ” 1\text{''} 1 ” 14-inch ( 350 mm 350\text{ mm} 350 mm ) Residential branch piping, furnace and water heater supplies

1 − 1 / 4 ” 1-1/4\text{''} 1 − 1/4 ” to 1 − 1 / 2 ” 1-1/2\text{''} 1 − 1/2 ” 18-inch ( 450 mm 450\text{ mm} 450 mm ) Main gas service lines, commercial distribution headers

2 ” 2\text{''} 2 ” 24-inch ( 600 mm 600\text{ mm} 600 mm ) Industrial gas headers, multi-unit manifold assemblies

Offset and End Wrenches: Feature angled jaws parallel to the handle to access tight corners or overhead pipe banks.

Aluminum Wrenches: Provide equivalent structural strength to ductile iron while reducing tool weight by approximately 40 % 40\% 40% , reducing fatigue during overhead work.

2. The Two-Wrench Technique ("Holding Back")

Whenever assembling or servicing threaded gas piping, applying torque with a single wrench transmits torsional stress upstream. The two-wrench technique (using a "hold-back wrench") is mandatory on all gas connections.

Backing Wrench (Hold-Back): Placed on the stationary fitting, coupling, or gas valve body, oriented to oppose the tightening wrench.

Tightening Wrench: Placed on the pipe nipple or component being rotated.

Hazards of Failing to Hold Back

Disturbed Upstream Joints: Torsional stress breaks the seal of concealed joints behind walls or in joist spaces, causing undetected leaks.

Cracked Gas Valves: Appliance control valves (furnaces, water heaters) feature cast aluminum or brass housings. Unopposed torque warps internal valve seats, damages shut-off solenoids, or cracks the valve casting.

Sheared Internal Lines: Rotational twisting breaks internal copper pilot lines or burner connections inside appliances.

3. Tubing Cutters, Reaming & Deburring Mechanics

Copper tubing (Types G, L, or K approved under CSA B149.1) and Corrugated Stainless Steel Tubing (CSST) require specialized cutting tools to maintain circular integrity.

Tubing Cutters

A tubing cutter features a hardened alloy cutting wheel opposed by guide rollers and an adjustable feed screw.

Tighten the feed knob until the wheel contacts the tube, rotate one full revolution ( 360 ∘ 360^\circ 36 0 ∘ ) to set a tracking line, then advance the knob 1 / 4 1/4 1/4 to 1 / 2 1/2 1/2 turn per revolution .

Never over-tighten the feed knob. Forcing the wheel flattens the tubing out-of-round (ovality), work-hardens copper, and forces an excessive internal burr into the bore.

Use manufacturer-specified stainless steel cutter wheels for CSST to avoid tearing corrugations.

Mandatory Reaming

Cutting pipe or tubing forces metal inward, creating a sharp internal burr . CSA B149.1 Clause 6.8 (piping practices) requires cutting burrs to be removed, so every cut pipe and tubing end is reamed:

Flow Restriction: An unreamed burr narrows the bore, causing turbulence and added pressure drop ( Δ P \Delta P Δ P ) that can starve appliances at peak firing.

Debris Accumulation: Burrs trap circulating pipe scale, rust, and thread sealant, eventually clogging appliance orifices and pilot burners.

Flare Failure: Burrs cause stress risers that crack copper flare skirts during expansion.

Note

When reaming steel pipe with a fluted cone reamer or copper with a deburring blade, always hold the pipe downward and tap firmly so metal shavings (swarf) drop out rather than entering the gas piping.

4. Flaring Tools: 45° SAE vs. 37° JIC Standards

Flared connections are a common joint for annealed copper tubing (see the joint requirements in CSA B149.1 Clause 6.9). Flared joints rely on a metal-to-metal seal between a brass fitting nose and an expanded copper tube end.

The 45° SAE Standard

45 ∘ SAE 45^\circ\text{ SAE} 4 5 ∘ SAE (SAE J513): Mandatory for fuel gas and HVAC/R installations across North America.

37 ∘ JIC 37^\circ\text{ JIC} 3 7 ∘ JIC (SAE J514): Reserved for hydraulic, military, and aircraft fluid lines.

Incompatibility: Mating a 45 ∘ 45^\circ 4 5 ∘ flare with a 37 ∘ 37^\circ 3 7 ∘ fitting creates a point-contact line seal that fails under gas pressure. Gas technicians must verify that flaring blocks are stamped 45 ∘ SAE 45^\circ\text{ SAE} 4 5 ∘ SAE .

Important

Never apply pipe dope, Teflon tape, or sealant to flare seating faces or flare nut threads . Flared fittings seal entirely by copper-to-brass compression. Sealants prevent proper metal seating, cause joint slippage, and contaminate gas valves.

Flaring Procedure

Slide the flare nut onto the tubing with the threads facing the cut end before clamping.

Clamp tubing in the flaring block with the tube extending approximately the thickness of a dime or nickel ( ≈ 1 / 16 inch \approx 1/16\text{ inch} ≈ 1/16 inch or 1.5 mm 1.5\text{ mm} 1.5 mm ) above the block face.

Use an eccentric (orbital) flaring tool , which rolls off-center to burnish the copper evenly without thinning or work-hardening the skirt.

Inspect the finished flare: it must be smooth, concentric, and free of cracks, splits, or galling.

5. Lever Tubing Benders and Pipe Vises

Lever Tubing Benders: Feature calibrated degree marks ( 0 ∘ , 45 ∘ , 90 ∘ , 180 ∘ 0^\circ, 45^\circ, 90^\circ, 180^\circ 0 ∘ , 4 5 ∘ , 9 0 ∘ , 18 0 ∘ ) on a fixed forming shoe. Bending in one smooth stroke preserves cross-sectional circularity and prevents kinking or flattening. Reversing an over-bent tube work-hardens copper, causing stress cracks.

Pipe Vises: Portable tristands provide rigid field support. Yoke vises use a V-shaped screw jaw for rapid clamping of rigid pipe, while chain vises wrap high-tensile chain around the circumference, distributing pressure evenly to prevent crushing thin-wall pipe.

Summary of Gas Piping Hand Tools

Tool Type Primary Gas Function Critical Operating Rule Severe Hazard of Misuse

Straight Pipe Wrench Assembling threaded steel gas pipe Always pull toward the open throat of the hook jaw Pushing slips, rounds fittings, and risks severe hand injury

Backing Wrench Countering torque across fittings Oppose primary wrench to isolate rotational stress Failure warps valve bodies, breaks joints, and creates leaks

Tubing Cutter Cutting copper and CSST tubing Advance knob gently ( 1 / 4 1/4 1/4 to 1 / 2 1/2 1/2 turn/rev) Over-tightening causes ovality and work-hardens copper

Fluted Pipe Reamer Removing internal cut burrs Ream clean; invert and tap pipe downward to clear swarf Unreamed burr narrows the bore and traps debris, starving burners

45° SAE Flaring Tool Forming dry mechanical flare seals Clamp tube ≈ 1 / 16 ” \approx 1/16\text{''} ≈ 1/16 ” above block; assemble dry Using 37 ∘ JIC 37^\circ\text{ JIC} 3 7 ∘ JIC or pipe dope creates persistent gas leaks

Lever Tubing Bender Executing uniform directional bends Align zero mark; pull lever in continuous smooth stroke Hand-bending kinks tubing, restricting gas flow and cracking walls

Loading diagram... Copper Tubing Preparation and 45° SAE Flare Fabrication Sequence