Study guide
12.4 Combustion Air & Basic Venting Requirements (Clause 8)
TSSA Gas Technician 3 G3
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety & Workplace Practices
1.1 Personal Protective Equipment (PPE) & Worksite Hazard Identification 1.2 WHMIS, GHS, Safety Data Sheets (SDS) & Chemical Safety 1.3 Electrical Safety, Lockout/Tagout (LOTO) & Confined Space Awareness
2 Chapter 2: Fasteners, Hand Tools & Power Tools
2.1 Hand Tools for Gas Piping and Mechanical Assembly 2.2 Power Tools, Threading Machines & Mechanical Fasteners
3 Chapter 3: Testing Instruments & Diagnostics
3.1 Pressure Measurement: U-Tube, Inclined & Digital Manometers 3.2 Electrical Multimeters, Combustion Analyzers & Electronic Leak Detectors
4 Chapter 4: Fuel Gas Properties & Combustion Principles
4.1 Chemical & Physical Properties of Natural Gas vs. Propane 4.2 Combustion Chemistry, Flammability Limits & Ignition Temperatures 4.3 Complete vs. Incomplete Combustion, Carbon Monoxide Hazards & Air Requirements
5 Chapter 5: Ontario Acts, Regulations & G.3 Scope of Authority
5.1 Technical Standards and Safety Act & O. Reg. 215/01 Certification 5.2 O. Reg. 211/01, O. Reg. 212/01 & TSSA Code Adoption Documents (CAD) 5.3 Unacceptable Conditions, Warning Notices & Red Tag Procedures
6 Chapter 6: CSA B149 Code Navigation & General Requirements
6.1 CSA B149.1 & CSA B149.2 Scope, Structure & Key Definitions 6.2 General Installation Rules: Instructions, Access, Clearances & Garages (Clause 4)
7 Chapter 7: Introduction to Electricity & Electrical Safety
7.1 Electrical Fundamentals: Ohm's Law, Power & Circuit Configurations 7.2 Line Voltage (120V) vs. Low Voltage (24V), Transformers & Circuit Protection 7.3 Basic Electrical Controls, Switches & Ladder Diagram Schematics
8 Chapter 8: Technical Manuals, Specifications & Architectural Drawings
8.1 Reading Appliance Rating Plates, Certified Manuals & Specifications 8.2 Architectural Blueprints, Mechanical Drawings & Piping Schematics
9 Chapter 9: Customer Relations, Professional Conduct & Documentation
9.1 Professional Communication, Ethics & Customer Service Standards 9.2 Work Orders, Service Documentation & Red Tag Communication
10 Chapter 10: Piping & Tubing Systems: Materials, Joining & Installation
10.1 Piping & Tubing Materials: Steel, Copper, CSST & Plastic 10.2 Pipe Joining Methods: Threading, Flaring, Brazing & Approved Sealants 10.3 Piping Installation: Supports, Hangers, Drip Legs, Dirt Pockets & Valves
11 Chapter 11: Gas Pipe Sizing, Pressure Testing & Purging Procedures
11.1 Gas Pipe & Tubing Sizing Fundamentals (Tables & Pressure Drop) 11.2 Pressure Testing, Leak Testing & the Ontario Test Tag (Clause 6.22) 11.3 Purging Procedures, Safety Protocols & Leak Detection (Clauses 6.23–6.24)
12 Chapter 12: Gas Appliances, Burners & Combustion Air Fundamentals
12.1 Appliance Classifications, Categories (I–IV), Approvals & Clearances 12.2 Atmospheric & Power Burners: Operation, Aeration & Flame Adjustment 12.3 Ignition Systems & Flame Safeguards: Standing Pilot, HSI, DSI, Thermocouples & Flame Rods 12.4 Combustion Air & Basic Venting Requirements (Clause 8)
12.4 Combustion Air & Basic Venting Requirements (Clause 8)
Key Takeaways Explain This Topic AI
For appliances totalling up to 400,000 Btu/h, CSA B149.1 Clause 8.2 sizes the outdoor air supply from Tables 8.1 to 8.4, chosen by building tightness and whether the appliances have draft control devices.
In a tight building, two draft-hooded appliances totalling 130,000 Btu/h are sized from the 150,000 Btu/h row of Table 8.1: 22 sq in. of free area, or a 5 in. round duct.
Above 400,000 Btu/h, Clause 8.4.2 requires 1 sq in. per 7,000 Btu/h up to 1,000,000 Btu/h plus 1 sq in. per 14,000 Btu/h above that for draft-control appliances, and Clause 8.4.3 requires 1 sq in. per 30,000 Btu/h for power burners.
Openings in louvres, grilles and screens must be at least 1/4 in. (6 mm); manually operated dampers are not allowed, and automatic dampers must be interlocked with the burner.
Under Clause 8.14.8, a vent may not terminate within 6 ft (1.8 m) of a mechanical air supply inlet, less than 1 ft (300 mm) above grade, or within 12 in. of an openable window for inputs over 10,000 up to 100,000 Btu/h (3 ft above 100,000 Btu/h).
Last updated: October 2026
Every gas appliance needs a continuous supply of air for combustion, and appliances with draft hoods also need dilution air. Modern airtight houses no longer leak enough air on their own, so Clause 8 of CSA B149.1 ( Venting systems and air supply for appliances ) tells you how to bring air in and how to get flue gases out safely. The Canadian method differs from the U.S. National Fuel Gas Code: B149.1 sizes air supply from tables , not from the U.S. "50 cubic feet per 1,000 Btu/h" confined-space rule.
1. What the Air Is For
Combustion air: about 10 cu ft of air per cu ft of natural gas burned (about 25 cu ft for propane).
Excess air: extra air (typically 20% to 50%) that ensures complete combustion.
Dilution air: air drawn into a draft hood or barometric damper to cool the flue gases and stabilize draft—only appliances with draft control devices need it.
Ventilation air: keeps the appliance room from overheating.
Starve a burner of air and it produces carbon monoxide and soot, and flames roll out toward the burner vestibule.
2. Appliances Totalling Up to 400,000 Btu/h (Clause 8.2)
Clause 8.2 covers the air supply for central furnaces, boilers and water heaters with a combined input up to and including 400,000 Btu/h (120 kW). Work through three questions:
Is the building tight? Clause 8.2.1 defines tight construction. Most new homes qualify; if in doubt, treat the building as tight.
Do the appliances have draft control devices (draft hood, draft diverter or barometric damper)?
Which table?
- Building With draft control devices Without draft control devices
- Tight (meets 8.2.1) Table 8.1 Table 8.2
- Loose (does not meet 8.2.1) Table 8.3 (by structure volume) Table 8.4 (by structure volume)
Enter the table at the total input , rounding up to the next listed input. The middle column gives the minimum free area of the air supply; the last column gives the minimum round duct size. In the loose-construction tables, a "0" means the structure's volume is large enough that no outdoor air supply is needed (round the volume down to the next listed value).
Mixed appliances (Clause 8.2.2): size from Table 8.1 (or 8.3) using only the appliances with draft control devices, size from Table 8.2 (or 8.4) using the total of all appliances, and provide the larger of the two.
Worked examples (tight construction)
80,000 Btu/h boiler + 50,000 Btu/h water heater, both with draft hoods: total 130,000 Btu/h → Table 8.1, 150,000 Btu/h row → 22 sq in. of free area, minimum 5 in. round duct.
Two 100,000 Btu/h fan-assisted boilers, no draft control: total 200,000 Btu/h → Table 8.2 → 14 sq in.
75,000 Btu/h draft-hood appliance + 50,000 Btu/h appliance without draft control: Table 8.1 at 75,000 Btu/h gives 11 sq in.; Table 8.2 at 125,000 Btu/h gives 9 sq in. → provide 11 sq in.
Other Clause 8.2–8.3 rules
Single water heater (Clause 8.2.3): a single water heater of 50,000 Btu/h or less needs no outdoor air supply, provided no other appliance in the space requires one.
Enclosure inside a loose structure (Clause 8.2.6): where the building volume is large enough, a room can draw its air from the rest of the building through a permanent opening of 1 sq in. per 1,000 Btu/h , located 6 to 18 in. above the floor, plus an equal ventilation opening placed high if any appliance has a draft control device.
Ducts (Clause 8.3): a square or rectangular air duct may have no dimension smaller than 3 in. (so never less than 9 sq in.).
Ontario CAD clause 7.1.12: a new or replacement residential boiler under 300,000 Btu/h that is not direct-vent must have its combustion air supplied from outdoors under Clauses 8.2.4 and 8.3 regardless of building construction, and the home needs CSA 6.19 carbon monoxide alarms at the sleeping areas.
3. Appliances Totalling Over 400,000 Btu/h (Clause 8.4)
Clause Requirement
8.4.1 Ventilation air A separate opening to outdoors, as high as practical and not within 12 in. of the air supply opening, with a free area of at least 10% of the air supply opening and never less than 10 sq in.
8.4.2 With draft control 1 sq in. per 7,000 Btu/h up to 1,000,000 Btu/h, plus 1 sq in. per 14,000 Btu/h above 1,000,000 Btu/h; opening located 6 to 18 in. above the floor
8.4.3 Power burners without draft control 1 sq in. per 30,000 Btu/h of total input
8.4.4 Mixed Calculate each group separately and add them (separate openings or one combined opening located per 8.4.2)
Example: 1,400,000 Btu/h of appliances, all with draft control: 1,000,000 7,000 + 400,000 14,000 = 142.9 + 28.6 = 171.4 sq in. \frac{1{,}000{,}000}{7{,}000} + \frac{400{,}000}{14{,}000} = 142.9 + 28.6 = 171.4\text{ sq in.} 7 , 000 1 , 000 , 000 + 14 , 000 400 , 000 = 142.9 + 28.6 = 171.4 sq in.
The ventilation opening must be at least 0.10 × 171.4 ≈ 17.1 sq in. 0.10 \times 171.4 \approx 17.1\text{ sq in.} 0.10 × 171.4 ≈ 17.1 sq in. (above the 10 sq in. minimum).
4. Louvres, Grilles, Screens and Dampers
Free area: a grille's bars reduce the open area. Use the manufacturer's free-area rating (commonly 35% to 60% of the gross opening). Required gross area = required free area ÷ grille efficiency; for 36 sq in. through a 60% grille, 36 ÷ 0.60 = 60 sq in. 36 \div 0.60 = 60\text{ sq in.} 36 ÷ 0.60 = 60 sq in.
Opening size: openings in a fixed louvre, grille or screen may be no smaller than 1/4 in. (6 mm) , so lint and frost cannot block them.
Dampers: manually operated dampers and manually adjustable louvres are not permitted ; automatic dampers are allowed only when interlocked so the burner cannot fire unless they are fully open.
- 5. Venting Basics, Draft Hoods and Spill Switches
- Natural draft
Category I appliances rely on natural draft : hot flue gas is lighter than the outdoor air, so it rises. Draft increases with vent height and with the temperature difference between the flue gas and outdoor air.
The draft hood (draft diverter)
A draft hood on a Category I appliance:
- isolates the burner from changes in chimney draft by providing a neutral pressure point at the flue outlet;
- admits dilution air , cooling the flue gas and stabilizing draft;
- lets a downdraft escape at the relief opening instead of blowing into the combustion chamber; and
relieves a blocked vent by spilling flue gas at the hood rather than smothering the flame.
Spill switches
Because spillage carries carbon monoxide into the house, many draft-hood appliances have a spill switch : a normally closed, usually manual-reset thermal switch near the draft hood relief opening. Hot flue gas spilling over it opens the switch and shuts off the gas valve. A tripped spill switch means a venting problem to find, never a switch to bypass.
6. Vent Termination Clearances (Clause 8.14.8)
Clause 8.14.8 lists places where a vent may not terminate. They include:
directly above a paved sidewalk or paved driveway located between two single-family dwellings and serving both;
- less than 7 ft (2.1 m) above a paved sidewalk or driveway on public property;
- within 6 ft (1.8 m) of a mechanical air supply inlet to any building;
above a meter/regulator assembly within 3 ft (900 mm) horizontally of the vertical centreline of the regulator vent outlet, up to a vertical distance of 15 ft (4.5 m);
less than 1 ft (300 mm) above grade;
within these distances of a window or door that can be opened, a non-mechanical air supply inlet, or another appliance's combustion air inlet: 6 in. (150 mm) for inputs up to 10,000 Btu/h, 12 in. (300 mm) over 10,000 and up to 100,000 Btu/h, and 3 ft (900 mm) over 100,000 Btu/h; and
under a veranda, porch or deck, unless it is fully open on at least two sides beneath the floor and the vent termination is at least 1 ft (300 mm) below the underside of the floor.
Manufacturers add their own clearances (inside corners, soffits, expected snow level), and the more stringent of code and instructions applies.
Warning
Never terminate a vent over a gas meter and regulator within 3 ft (900 mm) horizontally of the regulator vent. Flue gas can corrode the regulator, condensate can freeze its vent, and gas released by the regulator could be ignited.