Study guide

10.3 Piping Installation: Supports, Hangers, Drip Legs, Dirt Pockets & Valves

TSSA Gas Technician 3 G3

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety & Workplace Practices

1.1 Personal Protective Equipment (PPE) & Worksite Hazard Identification 1.2 WHMIS, GHS, Safety Data Sheets (SDS) & Chemical Safety 1.3 Electrical Safety, Lockout/Tagout (LOTO) & Confined Space Awareness

2 Chapter 2: Fasteners, Hand Tools & Power Tools

2.1 Hand Tools for Gas Piping and Mechanical Assembly 2.2 Power Tools, Threading Machines & Mechanical Fasteners

3 Chapter 3: Testing Instruments & Diagnostics

3.1 Pressure Measurement: U-Tube, Inclined & Digital Manometers 3.2 Electrical Multimeters, Combustion Analyzers & Electronic Leak Detectors

4 Chapter 4: Fuel Gas Properties & Combustion Principles

4.1 Chemical & Physical Properties of Natural Gas vs. Propane 4.2 Combustion Chemistry, Flammability Limits & Ignition Temperatures 4.3 Complete vs. Incomplete Combustion, Carbon Monoxide Hazards & Air Requirements

5 Chapter 5: Ontario Acts, Regulations & G.3 Scope of Authority

5.1 Technical Standards and Safety Act & O. Reg. 215/01 Certification 5.2 O. Reg. 211/01, O. Reg. 212/01 & TSSA Code Adoption Documents (CAD) 5.3 Unacceptable Conditions, Warning Notices & Red Tag Procedures

6 Chapter 6: CSA B149 Code Navigation & General Requirements

6.1 CSA B149.1 & CSA B149.2 Scope, Structure & Key Definitions 6.2 General Installation Rules: Instructions, Access, Clearances & Garages (Clause 4)

7 Chapter 7: Introduction to Electricity & Electrical Safety

7.1 Electrical Fundamentals: Ohm's Law, Power & Circuit Configurations 7.2 Line Voltage (120V) vs. Low Voltage (24V), Transformers & Circuit Protection 7.3 Basic Electrical Controls, Switches & Ladder Diagram Schematics

8 Chapter 8: Technical Manuals, Specifications & Architectural Drawings

8.1 Reading Appliance Rating Plates, Certified Manuals & Specifications 8.2 Architectural Blueprints, Mechanical Drawings & Piping Schematics

9 Chapter 9: Customer Relations, Professional Conduct & Documentation

9.1 Professional Communication, Ethics & Customer Service Standards 9.2 Work Orders, Service Documentation & Red Tag Communication

10 Chapter 10: Piping & Tubing Systems: Materials, Joining & Installation

10.1 Piping & Tubing Materials: Steel, Copper, CSST & Plastic 10.2 Pipe Joining Methods: Threading, Flaring, Brazing & Approved Sealants 10.3 Piping Installation: Supports, Hangers, Drip Legs, Dirt Pockets & Valves

11 Chapter 11: Gas Pipe Sizing, Pressure Testing & Purging Procedures

11.1 Gas Pipe & Tubing Sizing Fundamentals (Tables & Pressure Drop) 11.2 Pressure Testing, Leak Testing & the Ontario Test Tag (Clause 6.22) 11.3 Purging Procedures, Safety Protocols & Leak Detection (Clauses 6.23–6.24)

12 Chapter 12: Gas Appliances, Burners & Combustion Air Fundamentals

12.1 Appliance Classifications, Categories (I–IV), Approvals & Clearances 12.2 Atmospheric & Power Burners: Operation, Aeration & Flame Adjustment 12.3 Ignition Systems & Flame Safeguards: Standing Pilot, HSI, DSI, Thermocouples & Flame Rods 12.4 Combustion Air & Basic Venting Requirements (Clause 8)

10.3 Piping Installation: Supports, Hangers, Drip Legs, Dirt Pockets & Valves

Key Takeaways Explain This Topic AI

CSA B149.1 Clause 6.8.3 requires individual supports spaced per Table 6.2—for horizontal steel pipe, 6 ft for NPS 1/2, 8 ft for NPS 3/4 and 1, and 10 ft for NPS 1-1/4 and larger—and forbids supporting gas piping from other piping.

Small copper tubing needs closer support spacing than steel pipe (read Table 6.2 by tubing outside diameter), CSST is supported as its manufacturer specifies, and copper should be isolated from steel hangers to prevent galvanic corrosion.

Under CSA B149.1 Clause 6.13, a drip leg collects liquid condensate at low points in wet gas distribution, whereas a dirt pocket (sediment trap) collects solid rust and scale immediately upstream of an appliance automatic gas valve.

Clause 6.13.1 requires a dirt pocket at the bottom of the final drop to most appliances, and Ontario's CAD (6.13.2(a)) sets the pocket depth at no less than 3 in. 3\text{ in.} 3 in. ( 75 mm 75\text{ mm} 75 mm ) or the pipe's internal diameter, whichever is greater.

Ontario's CAD clause 6.18.2 puts the manual shut-off valve in the drop or riser, within 50 ft 50\text{ ft} 50 ft ( 15 m 15\text{ m} 15 m ) of a residential appliance, identified by a tag or sign, and readily accessible; install the union or connector downstream of it.

Last updated: October 2026

Piping Installation: Supports, Hangers, Drip Legs, Dirt Pockets & Valves

A safe fuel gas distribution network requires more than compliant pipe materials and leak-tight joints. Once assembled, piping and tubing systems must be permanently anchored against gravitational sag, seismic and building vibrations, and thermal expansion. Furthermore, sensitive appliance combination gas valves must be protected from circulating pipe scale and debris, and technicians must have immediate means to isolate equipment for servicing. These structural and operational requirements are governed by CSA B149.1 Clause 6.8 (Piping Supports) , Clause 6.13 (Drip Legs and Dirt Pockets) , and Clause 6.18 (Manual Shut-Off Valves) .

1. Pipe Hangers, Supports & Structural Anchoring (Table 6.2)

Gas piping must be securely supported from substantial structural framing members—such as solid wood floor joists, engineered steel beams, or reinforced concrete slabs. Gas piping must never be supported from dropped acoustic ceiling grids, electrical conduit, sheet metal ductwork, or adjacent plumbing pipes.

The Engineering Rationale for Support Spacing

Inadequate pipe support introduces multiple safety hazards:

Piping Sag and Low-Point Traps: Unsupported pipe sags under its own deadweight. A sagging pipe run creates unintended low points where condensed water vapor, heavy hydrocarbon liquids, and oil distillates pool, creating flow blockages and burner pulsation.

Joint Stress and Fatigue Failure: Excessive span lengths between hangers permit building vibrations and cyclic thermal expansion to exert continuous bending moments on threaded joints, leading to fatigue cracking at thread roots.

CSA B149.1 Table 6.2 Maximum Horizontal Support Intervals

Clause 6.8.3 requires piping and tubing to have individual supports of sufficient strength—never support it from other piping—spaced according to Table 6.2:

  • Piping Material & Size Maximum Horizontal Support Spacing
  • Steel pipe NPS 1/2 6 ft 6\text{ ft} 6 ft
  • Steel pipe NPS 3/4 and NPS 1 8 ft 8\text{ ft} 8 ft
  • Steel pipe NPS 1-1/4 and larger 10 ft 10\text{ ft} 10 ft
  • Copper tubing Closer spacing for small outside diameters—read Table 6.2 by tubing OD
  • CSST As the CSST manufacturer's instructions specify

On rooftops, Clause 6.25.1 adds that piping NPS 1 and larger follows Table 6.2 with a support at every threaded fitting, while smaller piping is supported vertically per Table 6.2 and horizontally every 4 ft 4\text{ ft} 4 ft ( 1.2 m 1.2\text{ m} 1.2 m ).

Vertical Piping Support and Riser Anchoring

Vertical gas piping (risers) passing through multi-story residential, commercial, or industrial buildings carries substantial deadweight load:

Support Interval: Table 6.2 also sets vertical support for risers (larger pipe is typically supported at every floor level). Support the base of each riser so its weight does not hang on branch fittings.

Riser Clamps: Heavy forged steel riser clamps bolted around the pipe must bear directly upon floor slabs or structural framing members to carry the deadweight without transferring downward shear loads to horizontal branch fittings.

Approved Hangers vs. Prohibited Makeshift Strapping

Approved Hangers: Steel clevis hangers, J-hooks, heavy two-hole steel pipe straps, and threaded rod suspensions anchored into structural framing.

Unsuitable Supports: Plumber's perforated metal tape (perforated band iron / plumber's strap), bailing wire, plastic zip-ties, and wooden cleats should not be used to support gas piping. Under fire conditions, thin perforated tape stretches and melts rapidly, dropping live gas pipes onto burning debris.

Dielectric Isolation for Copper Tubing

When supporting copper tubing with steel hangers or concrete anchors, technicians must prevent direct metal-to-metal contact:

Galvanic Cell Corrosion: Direct contact between dissimilar metals (ferrous steel and non-ferrous copper) in the presence of ambient moisture creates a galvanic battery cell. The steel hanger or copper wall experiences accelerated electrolytic corrosion, eventually puncturing the tubing.

Isolation: Support copper tubing with copper-plated hangers, plastic-coated brackets, or cushioned clamps so it does not touch steel hangers.

2. Drip Legs vs. Dirt Pockets (Clause 6.13)

While technicians in the field frequently use the terms interchangeably, CSA B149.1 Clause 6.13 establishes clear engineering and operational distinctions between a Drip Leg and a Dirt Pocket (Sediment Trap). +-------------------------------------------------------------+

  • | DRIP LEG vs. DIRT POCKET |
  • | |
  • | DRIP LEG (Condensate Collector): |
  • | - Lowest point of wet gas distribution system |
  • | - Collects liquid water vapor and hydrocarbon liquids |
  • | - Accessible for regular manual draining |
  • | |
  • | DIRT POCKET (Sediment Trap): |
  • | - Located immediately upstream of appliance gas valve |
  • | - Collects solid rust, mill scale, and pipe shavings |
  • | - Bottom of final drop; ON depth >= 3 in. or pipe ID |
  • +-------------------------------------------------------------+
  • 1. Drip Legs (Condensate Accumulators)

Primary Purpose: To capture liquid condensates—specifically water vapor and liquid hydrocarbon distillates (hexanes, heptanes) that drop out of the fuel gas stream when exposed to cold outdoor temperatures.

Location: Clause 6.13.5 requires a drip pocket wherever condensation can collect—for example where piping is exposed to wide or sudden temperature changes—unless moisture-removal equipment is installed upstream. Slope piping toward the drip pocket so liquid drains to it.

Maintenance: Must be fully accessible to allow utility technicians to uncap and drain accumulated liquids before they migrate downstream.

2. Dirt Pockets / Sediment Traps (Particulate Interceptors)

Primary Purpose: To intercept solid physical particulates—including steel mill scale, iron rust flakes, metal threading filings, and chunks of hardened pipe dope—before they reach the combination gas valve.

Why It Matters: An appliance combination gas valve utilizes precision-machined aluminum seats and delicate elastomer solenoid seals. If a single particle of rust or pipe scale lodges under the safety shut-off valve seat, the valve cannot close completely when the thermostat is satisfied, causing continuous gas leakage into the combustion chamber and creating an extreme explosion hazard.

Construction and Geometry of a Compliant Dirt Pocket

Clause 6.13.1 requires a dirt pocket at the bottom of the final drop serving an appliance. The usual construction is:

Standard Tee Fitting: Installed in the piping run immediately upstream of the appliance combination gas valve.

Pocket Depth: A capped nipple below the tee forms the pocket. Ontario's CAD (clause 6.13.2(a)) requires a depth of at least 3 in. 3\text{ in.} 3 in. ( 75 mm 75\text{ mm} 75 mm ) or the internal diameter of the pipe it serves, whichever is greater .

Flow Direction Change: Gas comes down the drop into the tee and turns 90 degrees out of the branch toward the appliance:

Dense physical debris traveling in the gas stream possesses higher momentum than the gas molecules.

When the gas stream makes a sharp 90-degree turn toward the appliance inlet, physical momentum carries the dense solid particles straight down into the 3-inch vertical capped nipple.

Warning

Non-Compliant Straight-Through Dirt Pocket Never install a dirt pocket where gas flows straight through the run of a horizontal tee with the capped nipple pointing down. In a straight horizontal flow, gas velocity carries rust and scale directly past the opening of the bottom nipple and straight into the appliance gas valve, defeating the entire purpose of the sediment trap.

Mandatory Applications & Code Exceptions (Clause 6.13)

Clause 6.13.1 requires a dirt pocket at the bottom of the final drop to every appliance except:

  • an illuminating appliance;
  • a range;
  • a clothes dryer;
  • an outdoor grill;
  • a portable appliance or equipment;
  • a decorative appliance or a gas log;
  • a room heater; and

an appliance that incorporates its own sediment trap.

Furnaces, boilers, water heaters and unit heaters therefore need one—including rooftop units, because "outdoor" is not an exception.

3. Manual Gas Shut-Off Valves (Clause 6.18)

Every gas appliance must have a dedicated means of local isolation to permit emergency shut-off, routine burner maintenance, and appliance replacement without depressurizing the remainder of the building piping network.

Valve Certification and Type (Clauses 6.18.1 and 6.18.4)

Under CSA B149.1-25 Clause 6.18.1, a manual shut-off valve must be certified to CSA 3.11 , CSA 3.16 , or CSA/ANSI Z21.15/CSA 9.1 (or be approved for use with gas) and must not be used outside its certified pressure and temperature range. Clause 6.18.4 requires a readily accessible valve of the ball, butterfly, eccentric or lubricated-plug type where the piping is larger than NPS 1, the tubing is 1 in. OD or larger, or the pressure exceeds 0.5 psig.

Modern installations universally utilize quarter-turn ball valves with forged brass or ductile iron bodies and stainless steel balls. Quarter-turn ball valves feature an external lever handle that provides unambiguous visual verification of valve status:

Handle Parallel to Pipe: Valve is OPEN (full port flow).

Handle Perpendicular ( 90 ∘ 90^\circ 9 0 ∘ ) to Pipe: Valve is CLOSED (positive bubble-tight shut-off).

Location, Distance, and Accessibility (Ontario CAD Clause 6.18.2)

Ontario's Gaseous Fuels CAD replaces B149.1 Clause 6.18.2. A manual shut-off valve shall be installed:

in either the drop or riser, as close as possible to the valve train of a commercial or industrial-type appliance ;

in either the drop or riser of a residential appliance ;

in the horizontal piping between the drop or riser and the appliance valve train—where it may be the same size as the appliance connection if it is within 2 ft (600 mm) of the appliance;

within a maximum of 50 ft (15 m) of the residential appliance it serves, identified as to the appliance it serves by a metal tag on the valve or a clear, legible, permanent sign beside it; and

so that it is readily accessible .

"Readily accessible" means the valve can be reached and operated quickly, without removing panels or climbing over obstructions. The CAD does not require the valve to be in the same room as the appliance, but it must be in the drop or riser, within 50 ft of a residential appliance, and identified.

Downstream Union Placement: The Non-Negotiable Order

When connecting an appliance to the gas distribution line using a ground-joint union or certified flexible metal appliance connector (ANSI Z21.24 / CSA 6.10), THE UNION OR CONNECTOR MUST ALWAYS BE INSTALLED DOWNSTREAM OF THE MANUAL SHUT-OFF VALVE . Gas Supply Line ---> [Manual Shut-Off Valve] ---> [Dirt Pocket Tee] ---> [Appliance Union] ---> [Gas Valve]

  • |
  • [3" Nipple]
  • |
  • [Cap]
  • Why the Union Must Be Downstream

If a technician needs to replace a defective combination gas valve or swap out a water heater, they close the manual shut-off valve.

Because the union is located downstream of the valve, unthreading the union disconnects the appliance while the manual valve holds back full gas pressure.

If a careless installer places the union upstream of the manual shut-off valve, breaking the union vents raw, pressurized gas into the mechanical room unless the entire building or facility is shut down at the main meter.

Important

An appliance union or flexible connector must ALWAYS be located downstream of the appliance manual shut-off valve. This allows complete equipment disconnection without depressurizing the upstream distribution system.

Loading diagram... Appliance Gas Train Piping Configuration (Clause 6.13 & 6.18)