Study guide
1.3 Electrical Safety, Lockout/Tagout (LOTO) & Confined Space Awareness
TSSA Gas Technician 3 G3
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety & Workplace Practices
1.1 Personal Protective Equipment (PPE) & Worksite Hazard Identification 1.2 WHMIS, GHS, Safety Data Sheets (SDS) & Chemical Safety 1.3 Electrical Safety, Lockout/Tagout (LOTO) & Confined Space Awareness
2 Chapter 2: Fasteners, Hand Tools & Power Tools
2.1 Hand Tools for Gas Piping and Mechanical Assembly 2.2 Power Tools, Threading Machines & Mechanical Fasteners
3 Chapter 3: Testing Instruments & Diagnostics
3.1 Pressure Measurement: U-Tube, Inclined & Digital Manometers 3.2 Electrical Multimeters, Combustion Analyzers & Electronic Leak Detectors
4 Chapter 4: Fuel Gas Properties & Combustion Principles
4.1 Chemical & Physical Properties of Natural Gas vs. Propane 4.2 Combustion Chemistry, Flammability Limits & Ignition Temperatures 4.3 Complete vs. Incomplete Combustion, Carbon Monoxide Hazards & Air Requirements
5 Chapter 5: Ontario Acts, Regulations & G.3 Scope of Authority
5.1 Technical Standards and Safety Act & O. Reg. 215/01 Certification 5.2 O. Reg. 211/01, O. Reg. 212/01 & TSSA Code Adoption Documents (CAD) 5.3 Unacceptable Conditions, Warning Notices & Red Tag Procedures
6 Chapter 6: CSA B149 Code Navigation & General Requirements
6.1 CSA B149.1 & CSA B149.2 Scope, Structure & Key Definitions 6.2 General Installation Rules: Instructions, Access, Clearances & Garages (Clause 4)
7 Chapter 7: Introduction to Electricity & Electrical Safety
7.1 Electrical Fundamentals: Ohm's Law, Power & Circuit Configurations 7.2 Line Voltage (120V) vs. Low Voltage (24V), Transformers & Circuit Protection 7.3 Basic Electrical Controls, Switches & Ladder Diagram Schematics
8 Chapter 8: Technical Manuals, Specifications & Architectural Drawings
8.1 Reading Appliance Rating Plates, Certified Manuals & Specifications 8.2 Architectural Blueprints, Mechanical Drawings & Piping Schematics
9 Chapter 9: Customer Relations, Professional Conduct & Documentation
9.1 Professional Communication, Ethics & Customer Service Standards 9.2 Work Orders, Service Documentation & Red Tag Communication
10 Chapter 10: Piping & Tubing Systems: Materials, Joining & Installation
10.1 Piping & Tubing Materials: Steel, Copper, CSST & Plastic 10.2 Pipe Joining Methods: Threading, Flaring, Brazing & Approved Sealants 10.3 Piping Installation: Supports, Hangers, Drip Legs, Dirt Pockets & Valves
11 Chapter 11: Gas Pipe Sizing, Pressure Testing & Purging Procedures
11.1 Gas Pipe & Tubing Sizing Fundamentals (Tables & Pressure Drop) 11.2 Pressure Testing, Leak Testing & the Ontario Test Tag (Clause 6.22) 11.3 Purging Procedures, Safety Protocols & Leak Detection (Clauses 6.23–6.24)
12 Chapter 12: Gas Appliances, Burners & Combustion Air Fundamentals
12.1 Appliance Classifications, Categories (I–IV), Approvals & Clearances 12.2 Atmospheric & Power Burners: Operation, Aeration & Flame Adjustment 12.3 Ignition Systems & Flame Safeguards: Standing Pilot, HSI, DSI, Thermocouples & Flame Rods 12.4 Combustion Air & Basic Venting Requirements (Clause 8)
1.3 Electrical Safety, Lockout/Tagout (LOTO) & Confined Space Awareness
Key Takeaways Explain This Topic AI
Lockout/Tagout (LOTO) establishes a verifiable Zero Energy State by isolating, locking, tagging, and dissipating all electrical, mechanical, pneumatic, and fuel gas energy sources prior to servicing equipment.
Electrical de-energization must be verified using the three-point Live-Dead-Live testing sequence with a calibrated digital multimeter (DMM) rated CAT III or CAT IV, confirming zero potential across all phase conductors and ground.
Every technician working on an isolated system should apply their own personal padlock and tag—directly on a multi-lock hasp or on a group lock box under a written group-lockout procedure such as CSA Z460 describes—because one worker locking out for others removes personal control of the hazard.
Under Ontario Regulation 632/05, a confined space is legally defined by three criteria: fully or partially enclosed, not designed or constructed for continuous human occupancy, and atmospheric hazards may occur due to construction, location, contents, or work.
Under O. Reg. 632/05 the atmosphere is tested before entry and as often as the plan requires; acceptable levels are oxygen 19.5 % 19.5\% 19.5% – 23 % 23\% 23% and flammable gas below 25 % 25\% 25% LEL (inspection only), 10 % 10\% 10% LEL (cold work) or 5 % 5\% 5% LEL with continuous monitoring (hot work), with contaminants such as C O CO CO below Regulation 833 limits.
Last updated: October 2026
Gas technicians operate at the mechanical-electrical boundary. Servicing gas-fired appliances requires daily interaction with line-voltage electrical circuits ( 120 V 120\text{ V} 120 V and 240 V 240\text{ V} 240 V ), low-voltage control circuits ( 24 V 24\text{ V} 24 V ), high-pressure fuel trains, and confined service areas. Eliminating electrical shock, arc flash explosions, inadvertent machine startup, and asphyxiation requires strict adherence to Lockout/Tagout (LOTO) standards and Ontario Regulation 632/05 ( Confined Spaces ).
Electrical Hazards & Physiological Effects in the Gas Trade
Electricity presents two primary risks: electric shock (current flowing through the human body) and arc flash / arc blast (thermal and acoustic energy released during an electrical fault).
The Physiological Effects of Current
Voltage is electrical potential ( V V V ), but amperage (current, I I I ) causes physiological injury. Ohm's Law demonstrates the relationship:
I = V R I = \frac{V}{R} I = R V
Under dry conditions, clean skin resistance ranges between 10,000 Ω 10{,}000\,\Omega 10 , 000 Ω and 100,000 Ω 100{,}000\,\Omega 100 , 000 Ω . In damp basements or with sweaty hands, resistance drops to 1,000 Ω 1{,}000\,\Omega 1 , 000 Ω . At 120 V 120\text{ V} 120 V , a contact with wet skin results in:
I = 120 V 1,000 Ω = 0.12 A = 120 mA I = \frac{120\text{ V}}{1{,}000\,\Omega} = 0.12\text{ A} = 120\text{ mA} I = 1 , 000 Ω 120 V = 0.12 A = 120 mA
This current is more than sufficient to induce fatal cardiac arrest.
Current Range Physiological Effect on the Human Body
1 mA 1\text{ mA} 1 mA Barely perceptible; slight tingling sensation.
5 mA 5\text{ mA} 5 mA Maximum harmless current; safe let-go threshold. (Basis for Class A GFCI tripping threshold: 4 to 6 mA 4\text{ to }6\text{ mA} 4 to 6 mA ).
10 to 20 mA 10\text{ to }20\text{ mA} 10 to 20 mA The "Let-Go" Threshold. Muscular tetany causes involuntary contraction of flexor muscles. The technician freezes to the conductor, unable to let go.
50 to 100 mA 50\text{ to }100\text{ mA} 50 to 100 mA Ventricular Fibrillation. Heart rhythm is disrupted; ventricles flutter without pumping blood. Brain damage occurs within 4 minutes, followed by death unless an AED and CPR are applied immediately.
1,000 to 2,000 mA 1{,}000\text{ to }2{,}000\text{ mA} 1 , 000 to 2 , 000 mA ( 1 to 2 A 1\text{ to }2\text{ A} 1 to 2 A ) Sustained myocardial contraction; severe internal and external burns; respiratory paralysis.
Arc Flash & Arc Blast Hazards
An arc flash is an electrical short circuit that ionizes air, producing a plasma discharge reaching temperatures exceeding 19,000 ∘ C 19{,}000\,^\circ\text{C} 19 , 000 ∘ C ( 35,000 ∘ F 35{,}000\,^\circ\text{F} 35 , 000 ∘ F ) . Solid copper vaporizes into gas, expanding 67,000 times 67{,}000\text{ times} 67 , 000 times in volume to generate an arc blast : an explosive supersonic pressure wave exceeding 160 dB 160\text{ dB} 160 dB that propels molten shrapnel. Technicians must de-energize and lock out systems before removing electrical covers.
Lockout / Tagout (LOTO) & Achieving a Zero Energy State
LOTO is governed by the OHSA through Ontario Regulation 213/91 ( Construction Projects , section 190 for electrical work) and Ontario Regulation 851 ( Industrial Establishments , section 42 for electrical equipment and section 76 for machinery), with CSA Z460 describing recognized lockout practice. The fundamental objective is to establish and maintain a Zero Energy State before maintenance begins.
Defining the Zero Energy State
A Zero Energy State is achieved when all primary, secondary, stored, and residual energy sources supplying an appliance are isolated, mechanically locked, tagged, and fully dissipated:
Electrical Energy: Line-voltage feeds ( 120 V / 240 V 120\text{ V} / 240\text{ V} 120 V /240 V ), control circuits ( 24 V 24\text{ V} 24 V ), and charged capacitors.
Chemical / Fuel Energy: Fuel gas contained in the piping train up to the appliance shutoff valve.
Pneumatic / Hydraulic Energy: Water pressure in hydronic loops, expansion tanks, and compressed air lines.
Mechanical / Potential Energy: Spring-loaded dampers and rotating blower wheels.
Thermal Energy: Hot water, steam boilers, and scalding vent piping.
The Six Standard Steps of LOTO
Preparation and Notification: Identify all energy isolating devices. Notify affected facility operators and building occupants that the equipment will be de-energized.
Equipment Shutdown: Shut down the appliance using standard operational controls (turn thermostat down or switch burner control to OFF) to bring rotating parts to rest and prevent switchbox arcing.
Energy Isolation: Throw the knife-switch handle of the dedicated electrical disconnect to OFF (or switch off the dedicated circuit breaker). Close the dedicated manual gas shutoff valve (quarter-turn ball valve or plug valve) perpendicular to the pipe.
Apply Lockout and Tagout Devices: Affix an approved, uniquely keyed personal safety padlock to the disconnect handle. If multiple technicians work on the system, apply a multi-lock hasp ("scissors hasp"); every technician must affix their own individual padlock . Attach a durable danger tag displaying the technician's name, company, phone number, date, and reason for lockout.
Dissipate Stored / Residual Energy: Bleed off trapped gas pressure between isolating valves. Discharge motor run/start capacitors using an insulated 20,000 Ω 20{,}000\,\Omega 20 , 000 Ω , 5 -watt 5\text{-watt} 5 -watt resistor. Block spring-loaded dampers and allow hot hydronic piping to cool.
Verification of Zero Energy ("The Try Step"): Attempt to restart the appliance using the normal operational thermostat or power switch to verify that it will not run. Immediately return the switch to OFF. Then proceed directly to electrical instrument testing.
Important
Personal control is the core lockout rule. Each technician working on the system attaches their own personal padlock—to the hasp, or to a group lock box under a written group-lockout procedure—and keeps the only key. Relying on someone else's lock, or on a verbal assurance that the equipment is off, removes that personal control.
Electrical Verification: The Three-Point Live-Dead-Live Protocol
Electrical de-energization must be verified using the Live-Dead-Live Test with a calibrated digital multimeter (DMM) rated CAT III ( 600 V 600\text{ V} 600 V or 1000 V 1000\text{ V} 1000 V ) or CAT IV ( 600 V 600\text{ V} 600 V ) :
Step 1 (Test Live): Probe a known, verified energized circuit of matching voltage. Confirm the display indicates expected voltage, proving the meter, battery, display, and test leads function correctly.
Step 2 (Test Dead): Probe the isolated equipment terminals on the load side of the disconnect or furnace control junction box. Measure:
- Phase-to-Phase (Line 1 to Line 2)
- Phase-to-Neutral (Line 1 to Neutral, Line 2 to Neutral)
- Phase-to-Ground (Line 1 to Ground, Line 2 to Ground)
- Neutral-to-Ground
Confirm every reading indicates exactly 0.0 V 0.0\text{ V} 0.0 V .
Step 3 (Re-test Live): Immediately re-test the known live voltage source to confirm the multimeter did not fail during the test.
Non-contact voltage detectors (NCVDs / "voltage pens") detect electrostatic fields only. They cannot detect shielded cables, DC voltages, or phase cancellations. An NCVD is an informal screening tool only; it is strictly prohibited as the sole verification of a Zero Energy State .
Confined Space Awareness & Ontario Regulation 632/05
Gas technicians frequently service restricted enclosures including crawl spaces, boiler combustion chambers, underground utility pits, and rooftop air handler plenums. In Ontario, confined space work is regulated under Ontario Regulation 632/05 ( Confined Spaces ).
Statutory Definition of a Confined Space
Under Section 1 of O. Reg. 632/05, a space is classified as a confined space only if it satisfies all three criteria:
It is fully or partially enclosed.
It is not designed and constructed for continuous human occupancy.
Atmospheric hazards may occur because of its construction, location, contents, or work performed in it.
Mandatory Atmospheric Limits
Before any worker enters a confined space, the atmosphere must be tested (a calibrated direct-reading 4-gas monitor is the usual tool). O. Reg. 632/05 defines acceptable oxygen and flammable-gas levels; other contaminants must stay within Regulation 833 exposure limits:
Atmospheric Parameter Acceptable Level Hazards Outside the Acceptable Level
Oxygen ( O 2 O_2 O 2 ) Concentration 19.5 % 19.5\% 19.5% to 23.0 % 23.0\% 23.0% by volume < 19.5 % <19.5\% < 19.5% : Impaired judgment, rapid fatigue, and fatal brain asphyxiation; > 23.0 % >23.0\% > 23.0% : Severe fire hazard; materials ignite violently with a single spark.
Flammable Gas / Vapor Concentration < 25 % <25\% < 25% LEL for inspection-only work; < 10 % <10\% < 10% LEL for cold work; < 5 % <5\% < 5% LEL for hot work (O. Reg. 632/05 s. 19) Rising toward the LEL means an explosion hazard; hot work also needs continuous monitoring, oxygen not above 23 % 23\% 23% , and a warning and exit procedure.
Carbon Monoxide ( C O CO CO ) < 25 ppm <25\text{ ppm} < 25 ppm TWA (Regulation 833 limit) Binds to hemoglobin 200 times 200\text{ times} 200 times more readily than oxygen. High levels cause convulsions, coma, and death ( 1,200 ppm 1{,}200\text{ ppm} 1 , 200 ppm is IDLH).
Hydrogen Sulfide ( H 2 S H_2S H 2 S ) < 10 ppm <10\text{ ppm} < 10 ppm TWA, 15 ppm 15\text{ ppm} 15 ppm STEL (Regulation 833) Paralyzes olfactory nerves at > 100 ppm >100\text{ ppm} > 100 ppm , causing rapid respiratory paralysis and fatal collapse.
Gas Stratification & Vapor Density
Gases layer within confined spaces based on Vapor Density relative to air ( 1.00 1.00 1.00 ):
Methane (Natural Gas): Vapor density ≈ 0.60 \approx 0.60 ≈ 0.60 (lighter than air). Rises and collects near the ceiling.
Carbon Monoxide ( C O CO CO ): Vapor density ≈ 0.97 \approx 0.97 ≈ 0.97 (nearly identical to air). Disperses evenly throughout the vertical space.
Hydrogen Sulfide ( H 2 S H_2S H 2 S ): Vapor density ≈ 1.19 \approx 1.19 ≈ 1.19 (heavier than air). Settles near the floor.
Propane ( C 3 H 8 C_3H_8 C 3 H 8 ): Vapor density ≈ 1.52 \approx 1.52 ≈ 1.52 (more than 1.5 times 1.5\text{ times} 1.5 times heavier than air). Pools in low sumps, floor drains, and crawl space bottoms.
Warning
Because gases stratify by vapor density, taking a single reading at the entrance is completely invalid. Technicians must sample at the top, middle, and bottom of the space before entry and maintain continuous monitoring while working.
Confined Space Entry Controls
Confined Space Entry Permit: Written permit identifying the space, verified energy isolation, atmospheric test results, authorized entrants, and standby attendant.
Continuous Mechanical Ventilation: Positive-pressure blowers delivering fresh outdoor air must run continuously.
The Standby Attendant: A trained attendant must remain stationed outside the entrance continuously to maintain communication and activate rescue. The attendant must never enter the space to attempt rescue. In U.S. data, NIOSH estimated that about one in four confined-space deaths were would-be rescuers.
Non-Entry Rescue Equipment: Where the rescue plan calls for non-entry rescue, entrants wear a full-body harness connected to an overhead tripod and winch retrieval line so they can be retrieved without anyone else entering.