Study guide

1.2 WHMIS, GHS, Safety Data Sheets (SDS) & Chemical Safety

TSSA Gas Technician 3 G3

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety & Workplace Practices

1.1 Personal Protective Equipment (PPE) & Worksite Hazard Identification 1.2 WHMIS, GHS, Safety Data Sheets (SDS) & Chemical Safety 1.3 Electrical Safety, Lockout/Tagout (LOTO) & Confined Space Awareness

2 Chapter 2: Fasteners, Hand Tools & Power Tools

2.1 Hand Tools for Gas Piping and Mechanical Assembly 2.2 Power Tools, Threading Machines & Mechanical Fasteners

3 Chapter 3: Testing Instruments & Diagnostics

3.1 Pressure Measurement: U-Tube, Inclined & Digital Manometers 3.2 Electrical Multimeters, Combustion Analyzers & Electronic Leak Detectors

4 Chapter 4: Fuel Gas Properties & Combustion Principles

4.1 Chemical & Physical Properties of Natural Gas vs. Propane 4.2 Combustion Chemistry, Flammability Limits & Ignition Temperatures 4.3 Complete vs. Incomplete Combustion, Carbon Monoxide Hazards & Air Requirements

5 Chapter 5: Ontario Acts, Regulations & G.3 Scope of Authority

5.1 Technical Standards and Safety Act & O. Reg. 215/01 Certification 5.2 O. Reg. 211/01, O. Reg. 212/01 & TSSA Code Adoption Documents (CAD) 5.3 Unacceptable Conditions, Warning Notices & Red Tag Procedures

6 Chapter 6: CSA B149 Code Navigation & General Requirements

6.1 CSA B149.1 & CSA B149.2 Scope, Structure & Key Definitions 6.2 General Installation Rules: Instructions, Access, Clearances & Garages (Clause 4)

7 Chapter 7: Introduction to Electricity & Electrical Safety

7.1 Electrical Fundamentals: Ohm's Law, Power & Circuit Configurations 7.2 Line Voltage (120V) vs. Low Voltage (24V), Transformers & Circuit Protection 7.3 Basic Electrical Controls, Switches & Ladder Diagram Schematics

8 Chapter 8: Technical Manuals, Specifications & Architectural Drawings

8.1 Reading Appliance Rating Plates, Certified Manuals & Specifications 8.2 Architectural Blueprints, Mechanical Drawings & Piping Schematics

9 Chapter 9: Customer Relations, Professional Conduct & Documentation

9.1 Professional Communication, Ethics & Customer Service Standards 9.2 Work Orders, Service Documentation & Red Tag Communication

10 Chapter 10: Piping & Tubing Systems: Materials, Joining & Installation

10.1 Piping & Tubing Materials: Steel, Copper, CSST & Plastic 10.2 Pipe Joining Methods: Threading, Flaring, Brazing & Approved Sealants 10.3 Piping Installation: Supports, Hangers, Drip Legs, Dirt Pockets & Valves

11 Chapter 11: Gas Pipe Sizing, Pressure Testing & Purging Procedures

11.1 Gas Pipe & Tubing Sizing Fundamentals (Tables & Pressure Drop) 11.2 Pressure Testing, Leak Testing & the Ontario Test Tag (Clause 6.22) 11.3 Purging Procedures, Safety Protocols & Leak Detection (Clauses 6.23–6.24)

12 Chapter 12: Gas Appliances, Burners & Combustion Air Fundamentals

12.1 Appliance Classifications, Categories (I–IV), Approvals & Clearances 12.2 Atmospheric & Power Burners: Operation, Aeration & Flame Adjustment 12.3 Ignition Systems & Flame Safeguards: Standing Pilot, HSI, DSI, Thermocouples & Flame Rods 12.4 Combustion Air & Basic Venting Requirements (Clause 8)

1.2 WHMIS, GHS, Safety Data Sheets (SDS) & Chemical Safety

Key Takeaways Explain This Topic AI

WHMIS in Canada incorporates the Globally Harmonized System (GHS), establishing standardized hazard classification criteria, uniform hazard pictograms, and 16-section Safety Data Sheets (SDSs).

Supplier labels require six core elements—product identifier, initial supplier identifier, hazard pictograms, signal word ('Danger' or 'Warning'), hazard statements, and precautionary statements—and each pictogram sits inside a red square-set-on-point (diamond) border.

Workplace labels are legally required under Ontario Regulation 860 whenever a hazardous product is transferred from its original container into another container, unless the portable-container exemption in section 10(2) applies; they require a product identifier, safe handling instructions, and a statement that an SDS is available.

Standardized Safety Data Sheets (SDSs) contain 16 uniform sections, with critical emergency and occupational exposure data located in Section 4 (First-Aid Measures), Section 5 (Fire-Fighting Measures), and Section 8 (Exposure Controls/Personal Protection).

Portable fire extinguisher operations follow the PASS protocol (Pull, Aim, Squeeze, Sweep); gas technicians must deploy Class B units for burning fuel gases and liquids, and Class C units for energized electrical switchgear, never using water on electrical or gas fires.

Last updated: October 2026

Gas technicians handle hazardous materials including compressed fuel gases, thread sealants, solvent cements, flux pastes, cutting lubricants, and refrigerants. Preventing acute poisoning, occupational illness, fires, and explosions requires thorough knowledge of the Workplace Hazardous Materials Information System (WHMIS) and rigorous chemical safety procedures.

The WHMIS & GHS Regulatory Architecture in Ontario

WHMIS is Canada's national hazard communication standard. It is governed federally by the Hazardous Products Act (HPA) and Hazardous Products Regulations (HPR) , administered by Health Canada. In Ontario, WHMIS is enforced under the Occupational Health and Safety Act (OHSA) and Ontario Regulation 860 ( Workplace Hazardous Materials Information System ).

WHMIS is aligned with the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) , standardizing hazard classifications, pictograms, label wording, and safety data sheets across international borders.

The Three Pillars of WHMIS

WHMIS functions through three interdependent components:

Hazard Labels: Warning labels affixed to containers alerting workers to key physical and health risks.

Safety Data Sheets (SDSs): Standardized 16-section technical documents detailing chemical properties, toxicology, first-aid, safe handling, and spill response.

Worker Education and Training: Mandatory instruction divided into General Education (principles of WHMIS, hazard classes, pictograms, and label formats) and Site-Specific Training (practical instruction on specific jobsite chemicals, mandatory PPE, decanting rules, emergency eye wash locations, and spill cleanup).

Employers must ensure all hazardous products are labelled, current SDSs are accessible to all workers on every shift without barriers, and training is reviewed annually.

WHMIS Hazard Pictograms & Classification

WHMIS classifies hazards into Physical Hazards (flammability, compressed gases, reactivity) and Health Hazards (toxicity, irritation, carcinogenicity).

Pictograms consist of a black symbol on a white background inside a solid red square set on a point (diamond border). The Biohazard pictogram retains a black trefoil in a round black border.

Pictogram Name Primary Hazard Description HVAC & Gas Trade Chemical Example

Flame Flammable gases, aerosols, liquids, solids Natural gas, propane, butane, acetone, aerosol leak detection sprays.

Flame Over Circle Oxidizing gases, liquids, and solids Compressed pure oxygen cylinders used in brazing rigs.

Gas Cylinder Gases under pressure (compressed, liquefied, dissolved) Nitrogen purge cylinders, acetylene, carbon dioxide, R-410A refrigerant.

Corrosion Corrosive to metals, skin burns, eye damage Hydrochloric (muriatic) acid descalers, caustic coil cleaners, zinc-chloride flux.

Exploding Bomb Explosives, self-reactive substances Unstable energetic compounds, highly reactive gas mixtures.

Skull and Crossbones Acute toxicity (fatal or toxic via oral, skin, or inhalation) Highly toxic industrial gases, concentrated ammonia refrigerants.

Health Hazard Carcinogenicity, respiratory sensitization, organ toxicity Crystalline silica from concrete drilling, legacy asbestos, benzene in lubricants.

Exclamation Mark Less severe toxicity, skin/eye irritation, narcotic effects Thread cutting oils, pipe joint compounds (pipe dope), solvent cleaners, PVC primers.

Biohazard Biohazardous infectious materials (pathogens) Stagnant condensate drain pans, cooling towers harboring Legionella pneumophila .

Signal Words

WHMIS labels use standardized Signal Words to indicate hazard severity:

"Danger": Used for higher-severity hazard categories (e.g., Category 1 Flammable Gas).

"Warning": Used for lower-severity hazard categories (e.g., Category 2 Flammable Gas).

If both apply to different hazard classes on the same product, only "Danger" appears on the label.

Supplier Labels vs. Workplace Labels

Ontario WHMIS legislation enforces two distinct types of product labels:

The Supplier Label

Created and affixed by the manufacturer or distributor. Under federal regulations, it must be bilingual (English and French) and contain six mandatory elements:

Product Identifier: Brand or chemical name matching the SDS.

Initial Supplier Identifier: Name, Canadian address, and phone number of the manufacturer or importer.

Hazard Pictograms: GHS pictograms in red diamond borders.

Signal Word: "Danger" or "Warning".

Hazard Statements: Standardized phrases describing hazard nature (e.g., "Extremely flammable gas").

Precautionary Statements: Prescribed phrases covering prevention, response, storage, and disposal.

The Workplace Label

Created and applied on-site by the employer or technician. Under O. Reg. 860, a workplace label is legally required:

When a chemical is decanted from its original container into a secondary container (e.g., pouring cutting oil from a 20-litre drum into an oiler squeeze can).

When the original supplier label becomes torn, defaced, or illegible.

When a chemical mixture is formulated on-site.

A compliant Workplace Label requires three mandatory elements :

Product Identifier: Matching the product name on the SDS.

Safe Handling Precautions: Required PPE and handling instructions (e.g., "Wear chemical splash goggles and nitrile gloves; use in ventilated area").

Reference to the SDS: An explicit statement stating that a Safety Data Sheet is available in the workplace.

Note

Under section 10(2) of O. Reg. 860, no label is required on a portable container filled directly from a labelled container if either (a) the product stays under the control of, and is used only by, the worker who filled it, is used only during that shift, and the contents are clearly identified; or (b) all of the product in the portable container is required for immediate use. If the container will be kept beyond those conditions, apply a workplace label.

Safety Data Sheets (SDSs): The Standardized 16-Section Structure

Under GHS and WHMIS, all SDSs follow a standardized 16-section format. Suppliers must update an SDS within 90 days of receiving significant new hazard data.

Section Section Title Key Content & Trade Relevance

1 Identification Product identifier, manufacturer contact, recommended uses, emergency phone.

2 Hazard Identification GHS classifications, signal word, pictograms, hazard/precautionary statements.

3 Composition / Ingredients Chemical names, CAS registry numbers, exact chemical concentrations.

4 First-Aid Measures Emergency instructions by exposure route (inhalation, eye, skin, ingestion) and physician notes.

5 Fire-Fighting Measures Suitable/unsuitable extinguishing media, combustion hazards, protective gear.

6 Accidental Release Measures Personal precautions, emergency procedures, containment, and cleanup.

7 Handling and Storage Safe handling, static grounding/bonding, ventilation, incompatible materials.

8 Exposure Controls / PPE Occupational limits (TWA, STEL, Ceiling), engineering controls, required PPE.

9 Physical & Chemical Properties Odor, pH, boiling point, flash point, flammability limits (LEL/UEL), vapor density.

10 Stability and Reactivity Stability, conditions to avoid (sparks, heat), hazardous decomposition products.

11 Toxicological Information Routes of entry, acute toxicity ( L D 50 LD_{50} L D 50 ​ , L C 50 LC_{50} L C 50 ​ ), immediate and chronic effects.

12–15 Ecological, Disposal, Transport, Regulatory Ecotoxicity, waste disposal, TDG shipping classifications (non-mandatory in Canada).

16 Other Information Preparation date, latest revision date, abbreviations.

Chemical Handling, Cylinder Safety & Fire Protection

Gas technicians work constantly with high-pressure gas cylinders and flammable materials.

Compressed Gas Cylinder Protocols

Upright Storage & Securing: All cylinders must be stored upright and secured to walls or carts using non-combustible chains or heavy-duty straps.

Valve Protection Caps: Steel caps must be hand-tightened over valves whenever cylinders are moved, transported, or not connected to a regulator.

Separation of Fuel and Oxidizing Gases: Fuel gas cylinders (acetylene, propane) must be stored at least 6 metres 6\text{ metres} 6 metres ( 20 feet 20\text{ feet} 20 feet ) away from oxidizing gas cylinders (oxygen), or separated by a non-combustible barrier wall at least 1.5 metres 1.5\text{ metres} 1.5 metres ( 5 feet 5\text{ feet} 5 feet ) high with a fire-resistance rating of at least 30 minutes 30\text{ minutes} 30 minutes .

Acetylene Orientation Rule: Acetylene is dissolved in liquid acetone inside a porous mass. Cylinders must always remain upright. If laid horizontally, acetone will enter the valve, dissolve regulator seals, and cause flashback explosions. If transported horizontally, stand upright for at least as long as it was horizontal (minimum 1 hour 1\text{ hour} 1 hour ) before opening the valve.

Warning

Never store fuel gas cylinders within 6 metres 6\text{ metres} 6 metres ( 20 feet 20\text{ feet} 20 feet ) of oxygen cylinders without an approved 1.5 -m 1.5\text{-m} 1.5 -m fire-rated barrier. Pure oxygen violently accelerates fuel combustion, generating blast conditions.

Fire Chemistry & Extinguisher Selection

Combustion requires four elements, represented by the Fire Tetrahedron : Fuel , Oxygen , Heat , and an Uninhibited Chemical Chain Reaction . Removing any single element extinguishes the fire.

Class A: Ordinary combustibles (wood, paper, textiles). Extinguished with water or multi-purpose dry chemical.

Class B: Flammable liquids and fuel gases (natural gas, propane, solvents, oils). Extinguished with carbon dioxide ( C O 2 CO_2 C O 2 ​ ) or dry chemical. Never extinguish a burning gas leak unless the fuel supply can be shut off immediately.

Class C: Energized electrical equipment (motors, circuit boards, transformers). Extinguished with non-conductive agents ( C O 2 CO_2 C O 2 ​ , dry chemical). Never use water due to fatal electrocution hazards.

Class D: Combustible metals (magnesium, titanium). Extinguished with dry powder agents.

Class K: Commercial cooking media (vegetable oils, animal fats). Extinguished with wet chemical agents.

The PASS Extinguisher Technique

Deploy portable fire extinguishers using the four-step PASS procedure:

P - Pull: Pull the safety locking pin, breaking the plastic tamper seal.

A - Aim: Aim the nozzle at the base of the fire, where fuel is burning.

S - Squeeze: Squeeze the operating lever to release the extinguishing agent.

S - Sweep: Sweep the nozzle smoothly from side to side across the base of the fire until extinguished. Stand 2 to 3 metres 2\text{ to }3\text{ metres} 2 to 3 metres ( 6 to 10 feet 6\text{ to }10\text{ feet} 6 to 10 feet ) back with an unobstructed escape path behind you.

Inspect extinguishers monthly: verify the pressure gauge needle is in the green zone, the safety pin is intact, the nozzle is unobstructed, the shell has no dents or severe rust, and the inspection tag is signed and dated.

Loading diagram... WHMIS Chemical Handling and Labeling Workflow