Study guide
18.3 Treatment & Wastewater Process Math Workshop
California Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: California Water Regulatory Framework & Certification Ladders
1.1 State Water Board & Regional Boards Structure 1.2 Drinking Water Certification: T1-T5 & D1-D5 Requirements 1.3 Wastewater Certification: Grades I-V & OIT Requirements 1.4 Safe Drinking Water Standards, MCLs & Emerging Contaminants 1.5 California Waterworks Standards (Title 22, Chapter 16) 1.6 Public Water System Types, Permits & the Sanitary Survey
2 Chapter 2: California Water Rights, Title 22 & Environmental Policy
2.1 California Title 22 Recycled Water Standards 2.2 California Environmental Quality Act (CEQA) & Proposition 218 2.3 Water Rights & California Water Resources
3 Chapter 3: Drinking Water Source Quality & Coagulation/Flocculation
3.1 Source Water Quality & Watershed Management 3.2 Coagulation Chemistry & Flash Mixing 3.3 Flocculation & Jar Testing 3.4 Wells, Aquifers & Groundwater Hydraulics 3.5 Raw Water Storage, Clearwells & Reservoir Management
4 Chapter 4: Clarification & Granular Media Filtration
4.1 Sedimentation & Advanced Clarification 4.2 Granular Media Filtration Mechanics & Media Types 4.3 Filter Operation, Backwash Cycles & SWTR Compliance
5 Chapter 5: Disinfection, Oxidation & Advanced Water Treatment
5.1 Chlorination Chemistry & Breakpoint Curves 5.2 Disinfection Kinetics & CT Calculations 5.3 Alternative Disinfection: Ozone, UV & Chlorine Dioxide 5.4 Advanced Treatment: Membranes, AOP & PFAS Adsorption 5.5 Chloramination & Nitrification Control 5.6 Iron & Manganese Removal 5.7 Fluoridation Practice & Compliance 5.8 Corrosion Control Treatment & Water Stability 5.9 Taste & Odor Control and Algal Toxin Management
6 Chapter 6: Wastewater Preliminary & Primary Treatment
6.1 Preliminary Treatment: Screening & Grit Removal 6.2 Primary Clarification Operations 6.3 Primary Sludge Characteristics & Pumping 6.4 Stabilization Ponds, Lagoons & Small-Plant Processes
7 Chapter 7: Secondary Biological Treatment & Activated Sludge
7.1 Activated Sludge Process Fundamentals 7.2 Process Control Parameters: F/M, MCRT & SVI 7.3 Activated Sludge Microbiology & Troubleshooting 7.4 Fixed-Film & Hybrid Biological Processes
8 Chapter 8: Biological Nutrient Removal, Water Reuse & Solids Handling
8.1 Biological Nitrogen Removal: Nitrification & Denitrification 8.2 Biological Phosphorus Removal (EBPR) & Chemical Precipitation 8.3 Anaerobic & Aerobic Digestion 8.4 Sludge Thickening, Dewatering & Biosolids Disposal 8.5 Wastewater Disinfection: Chlorination, Dechlorination & UV
9 Chapter 9: Distribution Systems, Collection Networks & Hydraulics
9.1 Hydraulics, Pressure & Flow Dynamics 9.2 Centrifugal Pumps, Motors & VFDs 9.3 Distribution Network Infrastructure & Cross-Connection Control 9.4 Wastewater Collection Systems, SSMP & FOG Management
10 Chapter 10: Laboratory Analytics, Safety & Water Math
10.1 Water & Wastewater Laboratory Methods 10.2 Laboratory Quality Assurance & Regulatory Reporting 10.3 Chemical Safety, Hazardous Gases & Confined Space 10.4 Essential Water & Wastewater Math for Operators
11 Chapter 11: Federal & California Drinking Water Rules
11.1 The Revised Total Coliform Rule & Assessments 11.2 The Lead and Copper Rule and Service Line Replacement 11.3 Surface Water Treatment Rules & Log Removal Credit 11.4 Stage 1 & Stage 2 Disinfection Byproduct Rules 11.5 Secondary MCLs, Notification Levels & Response Levels 11.6 Public Notification, Consumer Confidence Reports & Recordkeeping
12 Chapter 12: Distribution System Design, Demand & Hydraulics
12.1 System Layout, Pressure Zones & Distribution Maps 12.2 Water Demand, Peaking Factors & Fire Flow 12.3 Distribution Storage: Types, Sizing & Turnover 12.4 Head Loss, C-Factor & Distribution Hydraulic Calculations 12.5 Water Hammer, Surge Control & Air Management
13 Chapter 13: Distribution Equipment Operation, Maintenance & Inspection
13.1 Valves: Types, Operation & Exercising Programs 13.2 Fire Hydrants: Types, Testing & Maintenance 13.3 Water Meters: Types, Accuracy & Meter Management 13.4 Instrumentation, In-Line Sensors, Telemetry & SCADA 13.5 Electrical Systems, Motors & Standby Generators 13.6 External Corrosion, Cathodic Protection & Asset Inspection
14 Chapter 14: Water Mains, Piping & Field Construction
14.1 Pipe Materials & Pipe Selection 14.2 Joints, Fittings, Thrust Restraint & Bedding 14.3 Main Installation, Tapping & Service Line Installation 14.4 Leak Detection, Water Loss Auditing & Main Repair 14.5 Main Cleaning & Maintenance: Flushing, Pigging & Lining 14.6 Excavation, Trench Safety & Utility Locating
15 Chapter 15: Disinfecting Distribution Facilities & Maintaining Water Quality
15.1 Water Main Disinfection (AWWA C651) 15.2 Disinfecting Storage Reservoirs (C652) & Wells (C654) 15.3 Maintaining Distribution Water Quality: Residual, Biofilm & Discolored Water 15.4 Cross-Connection Control Program Administration & Device Testing
16 Chapter 16: Plant Equipment, Chemical Feed & Maintenance
16.1 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 16.2 Gas Chlorination Equipment & Hypochlorite Systems 16.3 Blowers, Compressors & Aeration Equipment 16.4 Flow Measurement Devices: Meters, Weirs & Flumes 16.5 Preventive Maintenance, CMMS & Asset Management
17 Chapter 17: Utility Management, Administration & Emergency Response
17.1 Planning, Organizing, Directing & Controlling a Utility Work Group 17.2 Budgets, Water Rates & Financial Management 17.3 Operator Training, Staffing & Safety Program Development 17.4 Energy Management & Optimization 17.5 Emergency Response Planning, Risk & Resilience & Security 17.6 Water Conservation Planning & Drought Response
18 Chapter 18: Applied Operator Mathematics Workshop
18.1 The Exam Conversion Sheet, Units & Dimensional Analysis 18.2 Distribution & Hydraulic Math Workshop 18.3 Treatment & Wastewater Process Math Workshop
18.3 Treatment & Wastewater Process Math Workshop
Key Takeaways Explain This Topic AI
CT is chlorine residual in mg/L multiplied by T10 contact time in minutes, and required CT depends on pH, temperature, and residual.
Log removal and log inactivation add to give total log reduction, and each log is a factor of ten.
Percent removal is influent minus effluent divided by influent, multiplied by 100.
F/M is pounds of BOD applied divided by pounds of MLVSS under aeration, and MCRT is pounds of solids in the system divided by pounds of solids leaving per day.
Percent solids and sludge volume relationships let an operator convert between gallons of sludge, pounds of dry solids, and cake weight.
Last updated: September 2026
CT and Log Reduction C T = Residual (mg/L) × T 10 (min) T 10 = Volume Flow × Baffling Factor CT = \text{Residual (mg/L)} \times T_{10} \text{ (min)} \qquad T_{10} = \frac{\text{Volume}}{\text{Flow}} \times \text{Baffling Factor} CT = Residual (mg/L) × T 10 (min) T 10 = Flow Volume × Baffling Factor C T Ratio = C T achieved C T required Log Inactivation = C T Ratio × Log required for that C T table value CT \text{ Ratio} = \frac{CT_{\text{achieved}}}{CT_{\text{required}}} \qquad \text{Log Inactivation} = CT\text{ Ratio} \times \text{Log required for that } CT \text{ table value} CT Ratio = C T required C T achieved Log Inactivation = CT Ratio × Log required for that CT table value
Problem 1. A 900,000-gallon clearwell operates at 3.6 MGD with superior baffling (0.7) and a free chlorine residual of 1.4 mg/L . The required CT for 0.5-log Giardia at this pH and temperature is 43 mg-min/L .
- Flow = 3.6 x 694.4 = 2,500 gpm
- DT = 900,000 / 2,500 = 360 min
T10 = 360 x 0.7 = 252 min CT achieved = 1.4 x 252 = 352.8 mg-min/L CT ratio = 352.8 / 43 = 8.2 - far in excess of the requirement, so the plant has substantial margin.
Problem 2. The same plant at peak flow of 9.0 MGD with residual dropping to 0.9 mg/L .
Flow = 6,250 gpm; DT = 144 min; T10 = 100.8 min CT = 0.9 x 100.8 = 90.7 mg-min/L ; ratio = 90.7 / 43 = 2.1 - still compliant but the margin has fallen by a factor of four. CT compliance is a peak-flow problem, not an average-flow problem.
Log Reduction Arithmetic Total Log = Log Removal + Log Inactivation \text{Total Log} = \text{Log Removal} + \text{Log Inactivation} Total Log = Log Removal + Log Inactivation
- Log Percent
- 0.5 68.4%
- 1 90%
- 2 99%
- 2.5 99.68%
- 3 99.9%
- 4 99.99%
Problem 3. A conventional plant earns 2.5-log Giardia removal from filtration and achieves a CT ratio giving 1.2-log inactivation. Total?
2.5 + 1.2 = 3.7-log , which exceeds the 3-log SWTR requirement with margin.
Problem 4. A direct filtration plant earns only 2.0-log removal. How much inactivation is needed for compliance?
3.0 − 2.0 = 1.0-log from disinfection, twice the conventional plant's 0.5-log burden.
Loading Rates Surface Overflow Rate (gpd/ft 2 ) = Flow (gpd) Surface Area (ft 2 ) \text{Surface Overflow Rate (gpd/ft}^2) = \frac{\text{Flow (gpd)}}{\text{Surface Area (ft}^2)} Surface Overflow Rate (gpd/ft 2 ) = Surface Area (ft 2 ) Flow (gpd) Weir Overflow Rate (gpd/ft) = Flow (gpd) Weir Length (ft) \text{Weir Overflow Rate (gpd/ft)} = \frac{\text{Flow (gpd)}}{\text{Weir Length (ft)}} Weir Overflow Rate (gpd/ft) = Weir Length (ft) Flow (gpd) Filtration Rate (gpm/ft 2 ) = Flow (gpm) Filter Area (ft 2 ) \text{Filtration Rate (gpm/ft}^2) = \frac{\text{Flow (gpm)}}{\text{Filter Area (ft}^2)} Filtration Rate (gpm/ft 2 ) = Filter Area (ft 2 ) Flow (gpm) Solids Loading Rate (lb/day/ft 2 ) = MLSS lb/day applied Clarifier Area (ft 2 ) \text{Solids Loading Rate (lb/day/ft}^2) = \frac{\text{MLSS lb/day applied}}{\text{Clarifier Area (ft}^2)} Solids Loading Rate (lb/day/ft 2 ) = Clarifier Area (ft 2 ) MLSS lb/day applied
Problem 5. A circular clarifier 75 ft in diameter treats 3.2 MGD . Its weir is a full-circumference launder.
- Area = 0.785 x 75² = 4,416 ft²
- SOR = 3,200,000 / 4,416 = 725 gpd/ft² Weir length = 3.14 x 75 = 235.5 ft
- WOR = 3,200,000 / 235.5 = 13,588 gpd/ft
Problem 6. A dual-media filter is 22 ft x 18 ft and receives 1,150 gpm .
- Area = 396 ft²
- Rate = 1,150 / 396 = 2.90 gpm/ft²
Problem 7. Unit filter run volume (UFRV) for that filter over a 62-hour run:
Volume = 1,150 gpm x 62 x 60 = 4,278,000 gal
UFRV = 4,278,000 / 396 = 10,803 gal/ft² - a healthy run; below about 5,000 gal/ft² suggests premature terminal head loss or breakthrough.
Percent Removal % Removal = In − Out In × 100 \% \text{ Removal} = \frac{\text{In} - \text{Out}}{\text{In}} \times 100 % Removal = In In − Out × 100
Problem 8. Influent BOD 240 mg/L , primary effluent 156 mg/L , final effluent 12 mg/L .
Primary removal = (240 − 156) / 240 x 100 = 35.0 percent Overall removal = (240 − 12) / 240 x 100 = 95.0 percent Secondary removal (of what reached it) = (156 − 12) / 156 x 100 = 92.3 percent
Note that these three numbers answer three different questions. Read the stem carefully to know which one is being asked.
Activated Sludge Process Control F/M = BOD applied (lb/day) MLVSS under aeration (lb) \text{F/M} = \frac{\text{BOD applied (lb/day)}}{\text{MLVSS under aeration (lb)}} F/M = MLVSS under aeration (lb) BOD applied (lb/day) MCRT (days) = lb MLSS in the system lb WAS/day + lb effluent TSS/day \text{MCRT (days)} = \frac{\text{lb MLSS in the system}}{\text{lb WAS/day} + \text{lb effluent TSS/day}} MCRT (days) = lb WAS/day + lb effluent TSS/day lb MLSS in the system SVI = Settled Volume (mL/L) × 1,000 MLSS (mg/L) \text{SVI} = \frac{\text{Settled Volume (mL/L)} \times 1{,}000}{\text{MLSS (mg/L)}} SVI = MLSS (mg/L) Settled Volume (mL/L) × 1 , 000 Sludge Age (days) = lb MLSS in aeration lb TSS entering per day \text{Sludge Age (days)} = \frac{\text{lb MLSS in aeration}}{\text{lb TSS entering per day}} Sludge Age (days) = lb TSS entering per day lb MLSS in aeration
Problem 9. Flow 5.2 MGD , influent BOD 185 mg/L , aeration volume 2.6 MG , MLSS 2,900 mg/L , volatile fraction 0.78 .
BOD applied = 5.2 x 185 x 8.34 = 8,023 lb/day MLVSS = 2,900 x 0.78 = 2,262 mg/L
MLVSS mass = 2.6 x 2,262 x 8.34 = 49,050 lb F/M = 8,023 / 49,050 = 0.164 day⁻¹ - conventional activated sludge range
Problem 10. Same plant. Aeration MLSS mass 62,900 lb (using total MLSS), WAS at 0.062 MGD and 7,400 mg/L , effluent TSS 9 mg/L .
WAS solids = 0.062 x 7,400 x 8.34 = 3,827 lb/day Effluent solids = 5.2 x 9 x 8.34 = 390 lb/day MCRT = 62,900 / (3,827 + 390) = 62,900 / 4,217 = 14.9 days
Problem 11. A 30-minute settleometer shows 310 mL/L at an MLSS of 2,900 mg/L .
SVI = (310 x 1,000) / 2,900 = 107 mL/g - good settling. Above about 150 suggests filamentous bulking; below about 70 suggests pin floc and an old sludge.
Problem 12. The plant wants to reduce MCRT from 14.9 to 11 days . What WAS mass is needed?
- Target total solids wasted = 62,900 / 11 = 5,718 lb/day Less effluent solids of 390 = 5,328 lb/day from WAS
- WAS flow = 5,328 / (7,400 x 8.34) = 5,328 / 61.7 = 0.0863 MGD = 86,300 gpd = 60 gpm
Tip
Change wasting gradually. Moving MCRT from 14.9 to 11 days in one step shocks the biomass. Standard practice is to change the wasting rate by no more than about 10 to 15 percent per day and let the system respond over one to two sludge ages.
Solids, Digesters, and Dewatering lb solids = Volume (MG) × Concentration (mg/L) × 8.34 \text{lb solids} = \text{Volume (MG)} \times \text{Concentration (mg/L)} \times 8.34 lb solids = Volume (MG) × Concentration (mg/L) × 8.34 lb solids = Volume (gal) × 8.34 × % solids 100 × Specific Gravity \text{lb solids} = \text{Volume (gal)} \times 8.34 \times \frac{\% \text{ solids}}{100} \times \text{Specific Gravity} lb solids = Volume (gal) × 8.34 × 100 % solids × Specific Gravity
Problem 13. A primary clarifier pumps 14,000 gal/day of sludge at 4.6 percent solids, specific gravity 1.02 .
lb/day = 14,000 x 8.34 x 0.046 x 1.02 = 5,478 lb/day of dry solids
Problem 14. That sludge is thickened to 6.0 percent . What is the thickened volume, assuming no solids loss?
Volume = 5,478 / (8.34 x 0.060 x 1.02) = 5,478 / 0.5104 = 10,733 gal/day
Problem 15. Volatile solids reduction using the Van Kleeck formula, with volatile fractions in as 0.72 and out as 0.53 : % V S R = V S i n − V S o u t V S i n − ( V S i n × V S o u t ) × 100 \% VSR = \frac{VS_{in} - VS_{out}}{VS_{in} - (VS_{in} \times VS_{out})} \times 100 % V SR = V S in − ( V S in × V S o u t ) V S in − V S o u t × 100
= (0.72 − 0.53) / (0.72 − 0.3816) x 100 = 0.19 / 0.3384 x 100 = 56.1 percent - above the 38 percent minimum for Part 503 vector attraction reduction Option 1.
Problem 16. Digester loading. A digester holds 420,000 gallons and receives 5,478 lb/day of solids at 72 percent volatile .
- Volume = 420,000 / 7.48 = 56,150 ft³
- VS fed = 5,478 x 0.72 = 3,944 lb/day
Loading = 3,944 / 56,150 = 0.070 lb VS/ft³/day - within the typical 0.04 to 0.10 range for a mesophilic complete-mix digester
Problem 17. Belt filter press performance. Feed is 80 gpm at 3.2 percent solids; cake is 19 percent solids; polymer dose is 14 lb per dry ton .
Feed solids = 80 x 1,440 x 8.34 x 0.032 = 30,744 lb/day = 15.4 dry tons/day Cake mass at 95 percent capture = 30,744 x 0.95 = 29,207 lb dry solids
Wet cake = 29,207 / 0.19 = 153,721 lb/day of wet cake ≈ 76.9 wet tons/day Polymer = 15.4 x 14 = 215 lb/day
Problem 18. Hauling cost at $62 per wet ton :
76.9 x 62 = $4,768 per day = $1.74 million per year - which is why a two-point improvement in cake solids is worth a great deal. At 21 percent cake, the wet tonnage falls to 69.5 tons/day and the annual cost to $1.57 million , a savings of roughly $170,000 per year .