Study guide
8.5 Wastewater Disinfection: Chlorination, Dechlorination & UV
California Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: California Water Regulatory Framework & Certification Ladders
1.1 State Water Board & Regional Boards Structure 1.2 Drinking Water Certification: T1-T5 & D1-D5 Requirements 1.3 Wastewater Certification: Grades I-V & OIT Requirements 1.4 Safe Drinking Water Standards, MCLs & Emerging Contaminants 1.5 California Waterworks Standards (Title 22, Chapter 16) 1.6 Public Water System Types, Permits & the Sanitary Survey
2 Chapter 2: California Water Rights, Title 22 & Environmental Policy
2.1 California Title 22 Recycled Water Standards 2.2 California Environmental Quality Act (CEQA) & Proposition 218 2.3 Water Rights & California Water Resources
3 Chapter 3: Drinking Water Source Quality & Coagulation/Flocculation
3.1 Source Water Quality & Watershed Management 3.2 Coagulation Chemistry & Flash Mixing 3.3 Flocculation & Jar Testing 3.4 Wells, Aquifers & Groundwater Hydraulics 3.5 Raw Water Storage, Clearwells & Reservoir Management
4 Chapter 4: Clarification & Granular Media Filtration
4.1 Sedimentation & Advanced Clarification 4.2 Granular Media Filtration Mechanics & Media Types 4.3 Filter Operation, Backwash Cycles & SWTR Compliance
5 Chapter 5: Disinfection, Oxidation & Advanced Water Treatment
5.1 Chlorination Chemistry & Breakpoint Curves 5.2 Disinfection Kinetics & CT Calculations 5.3 Alternative Disinfection: Ozone, UV & Chlorine Dioxide 5.4 Advanced Treatment: Membranes, AOP & PFAS Adsorption 5.5 Chloramination & Nitrification Control 5.6 Iron & Manganese Removal 5.7 Fluoridation Practice & Compliance 5.8 Corrosion Control Treatment & Water Stability 5.9 Taste & Odor Control and Algal Toxin Management
6 Chapter 6: Wastewater Preliminary & Primary Treatment
6.1 Preliminary Treatment: Screening & Grit Removal 6.2 Primary Clarification Operations 6.3 Primary Sludge Characteristics & Pumping 6.4 Stabilization Ponds, Lagoons & Small-Plant Processes
7 Chapter 7: Secondary Biological Treatment & Activated Sludge
7.1 Activated Sludge Process Fundamentals 7.2 Process Control Parameters: F/M, MCRT & SVI 7.3 Activated Sludge Microbiology & Troubleshooting 7.4 Fixed-Film & Hybrid Biological Processes
8 Chapter 8: Biological Nutrient Removal, Water Reuse & Solids Handling
8.1 Biological Nitrogen Removal: Nitrification & Denitrification 8.2 Biological Phosphorus Removal (EBPR) & Chemical Precipitation 8.3 Anaerobic & Aerobic Digestion 8.4 Sludge Thickening, Dewatering & Biosolids Disposal 8.5 Wastewater Disinfection: Chlorination, Dechlorination & UV
9 Chapter 9: Distribution Systems, Collection Networks & Hydraulics
9.1 Hydraulics, Pressure & Flow Dynamics 9.2 Centrifugal Pumps, Motors & VFDs 9.3 Distribution Network Infrastructure & Cross-Connection Control 9.4 Wastewater Collection Systems, SSMP & FOG Management
10 Chapter 10: Laboratory Analytics, Safety & Water Math
10.1 Water & Wastewater Laboratory Methods 10.2 Laboratory Quality Assurance & Regulatory Reporting 10.3 Chemical Safety, Hazardous Gases & Confined Space 10.4 Essential Water & Wastewater Math for Operators
11 Chapter 11: Federal & California Drinking Water Rules
11.1 The Revised Total Coliform Rule & Assessments 11.2 The Lead and Copper Rule and Service Line Replacement 11.3 Surface Water Treatment Rules & Log Removal Credit 11.4 Stage 1 & Stage 2 Disinfection Byproduct Rules 11.5 Secondary MCLs, Notification Levels & Response Levels 11.6 Public Notification, Consumer Confidence Reports & Recordkeeping
12 Chapter 12: Distribution System Design, Demand & Hydraulics
12.1 System Layout, Pressure Zones & Distribution Maps 12.2 Water Demand, Peaking Factors & Fire Flow 12.3 Distribution Storage: Types, Sizing & Turnover 12.4 Head Loss, C-Factor & Distribution Hydraulic Calculations 12.5 Water Hammer, Surge Control & Air Management
13 Chapter 13: Distribution Equipment Operation, Maintenance & Inspection
13.1 Valves: Types, Operation & Exercising Programs 13.2 Fire Hydrants: Types, Testing & Maintenance 13.3 Water Meters: Types, Accuracy & Meter Management 13.4 Instrumentation, In-Line Sensors, Telemetry & SCADA 13.5 Electrical Systems, Motors & Standby Generators 13.6 External Corrosion, Cathodic Protection & Asset Inspection
14 Chapter 14: Water Mains, Piping & Field Construction
14.1 Pipe Materials & Pipe Selection 14.2 Joints, Fittings, Thrust Restraint & Bedding 14.3 Main Installation, Tapping & Service Line Installation 14.4 Leak Detection, Water Loss Auditing & Main Repair 14.5 Main Cleaning & Maintenance: Flushing, Pigging & Lining 14.6 Excavation, Trench Safety & Utility Locating
15 Chapter 15: Disinfecting Distribution Facilities & Maintaining Water Quality
15.1 Water Main Disinfection (AWWA C651) 15.2 Disinfecting Storage Reservoirs (C652) & Wells (C654) 15.3 Maintaining Distribution Water Quality: Residual, Biofilm & Discolored Water 15.4 Cross-Connection Control Program Administration & Device Testing
16 Chapter 16: Plant Equipment, Chemical Feed & Maintenance
16.1 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 16.2 Gas Chlorination Equipment & Hypochlorite Systems 16.3 Blowers, Compressors & Aeration Equipment 16.4 Flow Measurement Devices: Meters, Weirs & Flumes 16.5 Preventive Maintenance, CMMS & Asset Management
17 Chapter 17: Utility Management, Administration & Emergency Response
17.1 Planning, Organizing, Directing & Controlling a Utility Work Group 17.2 Budgets, Water Rates & Financial Management 17.3 Operator Training, Staffing & Safety Program Development 17.4 Energy Management & Optimization 17.5 Emergency Response Planning, Risk & Resilience & Security 17.6 Water Conservation Planning & Drought Response
18 Chapter 18: Applied Operator Mathematics Workshop
18.1 The Exam Conversion Sheet, Units & Dimensional Analysis 18.2 Distribution & Hydraulic Math Workshop 18.3 Treatment & Wastewater Process Math Workshop
8.5 Wastewater Disinfection: Chlorination, Dechlorination & UV
Key Takeaways Explain This Topic AI
Disinfection is named in 23 CCR 3701(c)(1) as Grade I wastewater exam content and therefore appears at every grade.
Chlorine residual toxic to aquatic life means most California NPDES permits require dechlorination, typically with sulfur dioxide, sodium bisulfite, or sodium metabisulfite.
Sulfur dioxide requires about 1.0 mg/L per mg/L of chlorine residual; sodium bisulfite about 1.5 mg/L and sodium metabisulfite about 1.4 mg/L per mg/L of residual.
UV disinfection has no residual and no byproducts, but its performance collapses with high total suspended solids, low UV transmittance, and quartz sleeve fouling.
Title 22 disinfected tertiary recycled water disinfected with chlorine requires a CT of at least 450 mg-min/L with a modal contact time of at least 90 minutes.
Last updated: September 2026
Regulatory Drivers
Disinfection appears in the Grade I statutory blueprint (23 CCR 3701(c)(1)) and again in the Grade II list, so it is tested on every wastewater exam. What the plant must achieve depends on where the effluent goes:
Effluent destination Typical requirement
Ocean outfall under the Ocean Plan Bacterial standards at the edge of the zone of initial dilution; often 30-day geometric mean limits
Inland surface water (NPDES) Fecal coliform or E. coli limits, plus a total residual chlorine limit that is often non-detect
Title 22 disinfected secondary-23 recycled water 7-day median total coliform ≤ 23 MPN/100 mL , no sample above 240 MPN/100 mL
Title 22 disinfected secondary-2.2 recycled water 7-day median total coliform ≤ 2.2 MPN/100 mL
Title 22 disinfected tertiary recycled water Filtered, then disinfected to a 7-day median total coliform ≤ 2.2 MPN/100 mL , ≤ 23 MPN/100 mL in no more than one sample in any 30-day period, never above 240 MPN/100 mL; with chlorine, CT ≥ 450 mg-min/L at a modal contact time of at least 90 minutes
Important
The Title 22 tertiary chlorine criterion is a CT and a modal contact time , both of which must be met. A plant can hit 450 mg-min/L with a high dose and a short basin and still fail, because the 90-minute modal contact time is a separate requirement. UV is an approved alternative to the chlorine CT pathway for tertiary recycled water, validated against a required dose.
Chlorine in Wastewater
Wastewater chlorine chemistry differs from drinking water in one decisive way: wastewater contains ammonia . Secondary effluent from a non-nitrifying plant typically carries 15 to 30 mg/L of ammonia-nitrogen, so added chlorine immediately forms chloramines rather than free chlorine. NH 3 + HOCl → NH 2 Cl + H 2 O \text{NH}_3 + \text{HOCl} \rightarrow \text{NH}_2\text{Cl} + \text{H}_2\text{O} NH 3 + HOCl → NH 2 Cl + H 2 O
Practical consequences:
A non-nitrified effluent is disinfected by combined chlorine , which is weaker, so doses run higher (5 to 20 mg/L) and contact times longer.
A fully nitrified effluent has little ammonia, so the same dose produces free chlorine - a much stronger disinfectant. Operators who nitrify seasonally must retune the chlorine dose or they will badly overdose in summer.
Nitrite exerts a very heavy chlorine demand (about 5 mg Cl₂ per mg NO₂-N). A partially nitrified effluent that is stalled at nitrite is the worst case: high demand, poor disinfection, unstable residual.
Total residual chlorine (TRC) is what a permit limits, and it includes both free and combined forms.
Contact Basin Design
Chlorine contact basins are serpentine to force plug flow. The same baffling factor logic used in drinking water applies: C T = Residual (mg/L) × T 10 (min) , T 10 = Volume Flow × Baffling Factor CT = \text{Residual (mg/L)} \times T_{10}\text{ (min)}, \qquad T_{10} = \frac{\text{Volume}}{\text{Flow}} \times \text{Baffling Factor} CT = Residual (mg/L) × T 10 (min) , T 10 = Flow Volume × Baffling Factor
Worked example. A contact basin holds 260,000 gallons, flow is 3.2 MGD (2,222 gpm), superior baffling gives a factor of 0.7, and the chlorine residual at the outlet is 4.5 mg/L.
Theoretical detention = 260,000 / 2,222 = 117 minutes T10 = 117 x 0.7 = 81.9 minutes CT = 4.5 x 81.9 = 369 mg-min/L - short of the 450 mg-min/L needed for Title 22 tertiary, and the 81.9-minute modal time is also below 90 minutes. This plant would need a higher residual and more contact volume or better baffling.
Basins accumulate solids at the turns; sludge deposits reduce effective volume, short-circuit flow, and exert chlorine demand , so periodic draining and cleaning is a real compliance activity, not housekeeping.
Dechlorination
Chlorine residual is acutely toxic to fish and invertebrates at concentrations far below what is needed for disinfection, so most California NPDES permits require dechlorination to non-detect before discharge.
Dechlorinating agent Approximate dose per mg/L of chlorine residual Notes
Sulfur dioxide (SO₂ gas) 1.0 mg/L Cheapest at scale; same handling hazards as chlorine gas; requires the same containment, scrubber, and SCBA program
- Sodium bisulfite (NaHSO₃) ~1.5 mg/L Liquid, safer to handle, common at small and mid-size plants
- Sodium metabisulfite (Na₂S₂O₅) ~1.4 mg/L Dry or solution
- Sodium sulfite (Na₂SO₃) ~1.8 mg/L Less common
Sodium thiosulfate ~1.5-2.0 mg/L Common for grab-sample quenching and small applications SO 2 + H 2 O → H 2 SO 3 H 2 SO 3 + HOCl → HCl + H 2 SO 4 \text{SO}_2 + \text{H}_2\text{O} \rightarrow \text{H}_2\text{SO}_3 \qquad \text{H}_2\text{SO}_3 + \text{HOCl} \rightarrow \text{HCl} + \text{H}_2\text{SO}_4 SO 2 + H 2 O → H 2 SO 3 H 2 SO 3 + HOCl → HCl + H 2 SO 4
Three control issues dominate:
Overdose consumes dissolved oxygen. Excess sulfite scavenges DO in the effluent and in the receiving water. A permit with both a TRC limit and a minimum DO limit forces a narrow operating window.
Underdose is a permit violation the moment the analyzer sees residual. Because the reaction is essentially instantaneous, control is by feed-forward from the chlorine residual analyzer with feedback trim from a post-dechlorination analyzer.
Analyzer maintenance is the whole game. A drifting amperometric analyzer produces either a violation or a DO sag. Calibrate on schedule and verify against a bench DPD or amperometric titration.
Worked example. Effluent flow is 4.0 MGD carrying a 3.8 mg/L total chlorine residual, dechlorinated with sodium bisulfite at a 1.5:1 ratio.
Chlorine to be neutralized = 4.0 x 3.8 x 8.34 = 126.8 lb/day Bisulfite required = 126.8 x 1.5 = 190 lb/day of bisulfite as 100 percent; divide by the solution strength and density to get gallons per day.
Ultraviolet Disinfection
UV inactivates organisms by dimerizing thymine bases in DNA and RNA at germicidal wavelengths near 254 nm . It has become the default for California recycled water and for many NPDES plants because it produces no residual to dechlorinate and no chlorinated byproducts . UV Dose (mJ/cm 2 ) = Intensity (mW/cm 2 ) × Exposure Time (s) \text{UV Dose (mJ/cm}^2) = \text{Intensity (mW/cm}^2) \times \text{Exposure Time (s)} UV Dose (mJ/cm 2 ) = Intensity (mW/cm 2 ) × Exposure Time (s)
Factor Effect on performance
Total suspended solids Particles shield organisms from UV. This is the single biggest failure mode. Tertiary filtration ahead of UV is essential for recycled water.
UV transmittance (UVT) at 254 nm The fraction of light passing through 1 cm of water. Secondary effluent commonly runs 55-65 percent; filtered tertiary 65-75 percent. Falling UVT means falling delivered dose.
Lamp age Output declines over lamp life; systems apply an end-of-lamp-life factor .
Quartz sleeve fouling Iron, manganese, hardness, and organic film on the sleeve block light. Mechanical wipers plus chemical cleaning are required maintenance.
Hydraulics Short-circuiting and poor approach conditions reduce actual exposure.
Photoreactivation and dark repair Some organisms repair UV damage; validated dose requirements account for this.
Validation matters in California: recycled water UV systems must be validated (NWRI/AwwaRF guidelines or equivalent) and operated within the validated envelope of flow, UVT, and lamp status. Operating outside that envelope is a compliance failure even if the coliform results look acceptable.
- Chlorine + dechlorination Ultraviolet
- Residual Yes, must be removed None
- Byproducts THMs, chlorinated organics, NDMA precursor reactions None
- Effective against Cryptosporidium Poor Excellent
- Sensitive to TSS Moderately Severely
- Sensitive to ammonia Yes (forms chloramines) No
- Safety hazard Toxic gas or corrosive liquids Electrical, UV exposure, mercury in lamps
- Operating cost driver Chemical Electricity and lamp replacement
Warning
A broken UV lamp releases mercury into the channel and into the effluent. Have a written lamp-breakage response: isolate the bank, stop flow through the affected channel if possible, notify the supervisor, follow the mercury spill procedure, and evaluate whether an effluent notification is required under the plant's waste discharge requirements.