Study guide
5.5 Chloramination & Nitrification Control
California Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: California Water Regulatory Framework & Certification Ladders
1.1 State Water Board & Regional Boards Structure 1.2 Drinking Water Certification: T1-T5 & D1-D5 Requirements 1.3 Wastewater Certification: Grades I-V & OIT Requirements 1.4 Safe Drinking Water Standards, MCLs & Emerging Contaminants 1.5 California Waterworks Standards (Title 22, Chapter 16) 1.6 Public Water System Types, Permits & the Sanitary Survey
2 Chapter 2: California Water Rights, Title 22 & Environmental Policy
2.1 California Title 22 Recycled Water Standards 2.2 California Environmental Quality Act (CEQA) & Proposition 218 2.3 Water Rights & California Water Resources
3 Chapter 3: Drinking Water Source Quality & Coagulation/Flocculation
3.1 Source Water Quality & Watershed Management 3.2 Coagulation Chemistry & Flash Mixing 3.3 Flocculation & Jar Testing 3.4 Wells, Aquifers & Groundwater Hydraulics 3.5 Raw Water Storage, Clearwells & Reservoir Management
4 Chapter 4: Clarification & Granular Media Filtration
4.1 Sedimentation & Advanced Clarification 4.2 Granular Media Filtration Mechanics & Media Types 4.3 Filter Operation, Backwash Cycles & SWTR Compliance
5 Chapter 5: Disinfection, Oxidation & Advanced Water Treatment
5.1 Chlorination Chemistry & Breakpoint Curves 5.2 Disinfection Kinetics & CT Calculations 5.3 Alternative Disinfection: Ozone, UV & Chlorine Dioxide 5.4 Advanced Treatment: Membranes, AOP & PFAS Adsorption 5.5 Chloramination & Nitrification Control 5.6 Iron & Manganese Removal 5.7 Fluoridation Practice & Compliance 5.8 Corrosion Control Treatment & Water Stability 5.9 Taste & Odor Control and Algal Toxin Management
6 Chapter 6: Wastewater Preliminary & Primary Treatment
6.1 Preliminary Treatment: Screening & Grit Removal 6.2 Primary Clarification Operations 6.3 Primary Sludge Characteristics & Pumping 6.4 Stabilization Ponds, Lagoons & Small-Plant Processes
7 Chapter 7: Secondary Biological Treatment & Activated Sludge
7.1 Activated Sludge Process Fundamentals 7.2 Process Control Parameters: F/M, MCRT & SVI 7.3 Activated Sludge Microbiology & Troubleshooting 7.4 Fixed-Film & Hybrid Biological Processes
8 Chapter 8: Biological Nutrient Removal, Water Reuse & Solids Handling
8.1 Biological Nitrogen Removal: Nitrification & Denitrification 8.2 Biological Phosphorus Removal (EBPR) & Chemical Precipitation 8.3 Anaerobic & Aerobic Digestion 8.4 Sludge Thickening, Dewatering & Biosolids Disposal 8.5 Wastewater Disinfection: Chlorination, Dechlorination & UV
9 Chapter 9: Distribution Systems, Collection Networks & Hydraulics
9.1 Hydraulics, Pressure & Flow Dynamics 9.2 Centrifugal Pumps, Motors & VFDs 9.3 Distribution Network Infrastructure & Cross-Connection Control 9.4 Wastewater Collection Systems, SSMP & FOG Management
10 Chapter 10: Laboratory Analytics, Safety & Water Math
10.1 Water & Wastewater Laboratory Methods 10.2 Laboratory Quality Assurance & Regulatory Reporting 10.3 Chemical Safety, Hazardous Gases & Confined Space 10.4 Essential Water & Wastewater Math for Operators
11 Chapter 11: Federal & California Drinking Water Rules
11.1 The Revised Total Coliform Rule & Assessments 11.2 The Lead and Copper Rule and Service Line Replacement 11.3 Surface Water Treatment Rules & Log Removal Credit 11.4 Stage 1 & Stage 2 Disinfection Byproduct Rules 11.5 Secondary MCLs, Notification Levels & Response Levels 11.6 Public Notification, Consumer Confidence Reports & Recordkeeping
12 Chapter 12: Distribution System Design, Demand & Hydraulics
12.1 System Layout, Pressure Zones & Distribution Maps 12.2 Water Demand, Peaking Factors & Fire Flow 12.3 Distribution Storage: Types, Sizing & Turnover 12.4 Head Loss, C-Factor & Distribution Hydraulic Calculations 12.5 Water Hammer, Surge Control & Air Management
13 Chapter 13: Distribution Equipment Operation, Maintenance & Inspection
13.1 Valves: Types, Operation & Exercising Programs 13.2 Fire Hydrants: Types, Testing & Maintenance 13.3 Water Meters: Types, Accuracy & Meter Management 13.4 Instrumentation, In-Line Sensors, Telemetry & SCADA 13.5 Electrical Systems, Motors & Standby Generators 13.6 External Corrosion, Cathodic Protection & Asset Inspection
14 Chapter 14: Water Mains, Piping & Field Construction
14.1 Pipe Materials & Pipe Selection 14.2 Joints, Fittings, Thrust Restraint & Bedding 14.3 Main Installation, Tapping & Service Line Installation 14.4 Leak Detection, Water Loss Auditing & Main Repair 14.5 Main Cleaning & Maintenance: Flushing, Pigging & Lining 14.6 Excavation, Trench Safety & Utility Locating
15 Chapter 15: Disinfecting Distribution Facilities & Maintaining Water Quality
15.1 Water Main Disinfection (AWWA C651) 15.2 Disinfecting Storage Reservoirs (C652) & Wells (C654) 15.3 Maintaining Distribution Water Quality: Residual, Biofilm & Discolored Water 15.4 Cross-Connection Control Program Administration & Device Testing
16 Chapter 16: Plant Equipment, Chemical Feed & Maintenance
16.1 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 16.2 Gas Chlorination Equipment & Hypochlorite Systems 16.3 Blowers, Compressors & Aeration Equipment 16.4 Flow Measurement Devices: Meters, Weirs & Flumes 16.5 Preventive Maintenance, CMMS & Asset Management
17 Chapter 17: Utility Management, Administration & Emergency Response
17.1 Planning, Organizing, Directing & Controlling a Utility Work Group 17.2 Budgets, Water Rates & Financial Management 17.3 Operator Training, Staffing & Safety Program Development 17.4 Energy Management & Optimization 17.5 Emergency Response Planning, Risk & Resilience & Security 17.6 Water Conservation Planning & Drought Response
18 Chapter 18: Applied Operator Mathematics Workshop
18.1 The Exam Conversion Sheet, Units & Dimensional Analysis 18.2 Distribution & Hydraulic Math Workshop 18.3 Treatment & Wastewater Process Math Workshop
5.5 Chloramination & Nitrification Control
Key Takeaways Explain This Topic AI
Monochloramine is formed by adding ammonia to free chlorine at a chlorine-to-ammonia-nitrogen weight ratio of about 3:1 to 5:1, with 4.5:1 to 5:1 the usual operating target.
Chloramines are a far weaker disinfectant than free chlorine, carrying a CT inactivation credit only for viruses and Giardia at very long contact times, so they are used as a secondary residual rather than a primary disinfectant.
Nitrification is the biological oxidation of excess free ammonia to nitrite and nitrate inside the distribution system, and it destroys chloramine residual while depressing pH and alkalinity.
The earliest reliable nitrification indicators are rising nitrite, falling total chlorine residual with a rising monochloramine-to-total-chlorine gap, and rising heterotrophic plate counts.
Chloramination is the single largest source of chloramine-specific distribution problems in California, and Chloramination is a named sub-topic in the SWRCB distribution Expected Range of Knowledge.
Last updated: September 2026
Why California Utilities Chloraminate
The Stage 1 and Stage 2 Disinfectants and Disinfection Byproducts Rules capped total trihalomethanes at 80 µg/L and the five haloacetic acids at 60 µg/L , evaluated as a locational running annual average at each monitoring site. Free chlorine held in a large distribution system for two or three days keeps reacting with natural organic matter and keeps making byproducts. Monochloramine forms dramatically less THM and HAA5 , holds a residual for far longer, and penetrates biofilm better. That combination drove most large California systems - Los Angeles, San Diego, the Metropolitan Water District service area, East Bay MUD and many others - to chloraminate.
The tradeoff is that chloramines introduce an entirely new failure mode: nitrification .
Chloramine Chemistry
Ammonia reacts with hypochlorous acid in three stages, and which species you get depends almost entirely on the chlorine-to-ammonia-nitrogen weight ratio and pH: NH 3 + HOCl → NH 2 Cl (monochloramine) + H 2 O \text{NH}_3 + \text{HOCl} \rightarrow \text{NH}_2\text{Cl (monochloramine)} + \text{H}_2\text{O} NH 3 + HOCl → NH 2 Cl (monochloramine) + H 2 O NH 2 Cl + HOCl → NHCl 2 (dichloramine) + H 2 O \text{NH}_2\text{Cl} + \text{HOCl} \rightarrow \text{NHCl}_2\text{ (dichloramine)} + \text{H}_2\text{O} NH 2 Cl + HOCl → NHCl 2 (dichloramine) + H 2 O NHCl 2 + HOCl → NCl 3 (trichloramine / nitrogen trichloride) + H 2 O \text{NHCl}_2 + \text{HOCl} \rightarrow \text{NCl}_3\text{ (trichloramine / nitrogen trichloride)} + \text{H}_2\text{O} NHCl 2 + HOCl → NCl 3 (trichloramine / nitrogen trichloride) + H 2 O
Cl₂ : NH₃-N weight ratio Dominant species Consequence
Below about 3:1 Monochloramine with free ammonia left over Excess ammonia feeds nitrifying bacteria - the primary cause of nitrification
About 4.5:1 to 5:1 Monochloramine, minimal free ammonia Target operating window
Above about 5:1 approaching 7.6:1 Dichloramine increasing Swimming-pool odor, taste complaints, faster residual decay
- At about 7.6:1 Breakpoint Chloramines destroyed; free chlorine reappears past this point
- Well above breakpoint Trichloramine Strong offensive odor; only formed at low pH
pH matters. Monochloramine is favored above roughly pH 8. Below pH 7 the equilibrium shifts toward dichloramine and eventually trichloramine. California systems generally chloraminate at pH 8.0 to 8.5, which also supports corrosion control.
Important
Order of addition. Feed chlorine first, then ammonia after a short free-chlorine contact period, or feed simultaneously with excellent mixing. Feeding ammonia first creates a zone where the ratio is far below 3:1, produces poorly disinfected water, and starts the nitrification cycle at the point of application. Some plants deliberately maintain a brief free chlorine contact time before ammoniation to earn CT credit as free chlorine, then convert to chloramine for the distribution residual.
Disinfection Strength
Chloramines are roughly 20 to 200 times weaker than free chlorine depending on the organism. In practical terms:
No Cryptosporidium credit at any realistic dose.
Very limited Giardia credit , requiring enormous CT.
Some virus credit at long contact time.
Excellent at penetrating biofilm and holding a residual for days, which is exactly what a large distribution system needs.
The standard California design is therefore primary disinfection with free chlorine, ozone, or UV inside the plant to earn the required log inactivation, then ammoniation to convert to a chloramine residual for the distribution system.
Nitrification: What Actually Happens
Nitrification is a two-step biological oxidation performed by autotrophic bacteria that colonize pipe walls and stagnant storage: NH 4 + + 1.5 O 2 → ammonia-oxidizing bacteria NO 2 − + 2 H + + H 2 O \text{NH}_4^+ + 1.5\,\text{O}_2 \xrightarrow{\text{ammonia-oxidizing bacteria}} \text{NO}_2^- + 2\text{H}^+ + \text{H}_2\text{O} NH 4 + + 1.5 O 2 ammonia-oxidizing bacteria NO 2 − + 2 H + + H 2 O NO 2 − + 0.5 O 2 → nitrite-oxidizing bacteria NO 3 − \text{NO}_2^- + 0.5\,\text{O}_2 \xrightarrow{\text{nitrite-oxidizing bacteria}} \text{NO}_3^- NO 2 − + 0.5 O 2 nitrite-oxidizing bacteria NO 3 −
It is a self-accelerating loop . Free ammonia feeds ammonia-oxidizing bacteria. They produce nitrite , which exerts a very strong chloramine demand (roughly 5 mg of chloramine consumed per 1 mg of nitrite as N ). Loss of chloramine releases more ammonia, which feeds more bacteria. Meanwhile the reaction releases hydrogen ions, depressing pH and consuming alkalinity , which in a poorly buffered system can destabilize corrosion control and mobilize lead.
- Conditions That Trigger It
- Excess free ammonia from running below a 4.5:1 ratio, or from over-dosing ammonia
- Long detention time - oversized or poorly turned-over storage, dead-end mains, low-demand seasons
Warm water - nitrifiers accelerate sharply above about 15 °C, so California systems see nitrification episodes in late summer and early fall
- Low chloramine residual - below roughly 0.5 mg/L total chlorine, control is lost
- Nutrient-rich biofilm on unlined cast iron
Monitoring and Early Warning
A nitrification action plan is now standard practice for California chloraminating utilities. The parameters, in rough order of how early they warn you:
Parameter Baseline Warning trend
Nitrite (NO₂-N) Near zero Any sustained rise above about 0.005-0.015 mg/L - the earliest and most specific indicator
Total chlorine residual System target, often 1.5-2.5 mg/L Falling faster than seasonal decay explains
Monochloramine vs total chlorine Nearly equal A widening gap means chloramine is being consumed and other chlorine species are present
Free ammonia Low and stable A rise means over-feed; a fall to zero with rising nitrite means bacteria are consuming it
- Heterotrophic plate count (HPC) Low A rise above about 500 CFU/mL signals microbial activity
- Nitrate (NO₃-N) Source baseline Slow rise confirms complete nitrification
- pH and alkalinity Stable Depression at the same sites
- Temperature Seasonal Above 15 °C raises risk
Tip
The pairing that identifies nitrification. Falling total chlorine residual plus rising nitrite at the same site is essentially diagnostic. Falling residual with no nitrite is ordinary chloramine decay - check detention time, temperature, and the feed. Rising nitrite with a stable residual is an early-stage event you can still get ahead of.
Response Actions, Least to Most Aggressive
Fix the ratio at the plant. Verify the chlorine-to-ammonia-nitrogen ratio by calculation and by measurement, and move it toward 4.5:1 or 5:1. Eliminating excess free ammonia removes the nitrifiers' food supply.
Increase turnover. Cycle storage tanks through a wider level band, deep-cycle problem reservoirs, and reduce detention time. Stagnation is the enabling condition.
Flush. Targeted or unidirectional flushing of dead ends and low-velocity mains removes nitrifying biofilm and stale water. Follow with residual verification.
Raise the chloramine residual at the entry point and at booster stations. Adding a chloramine booster at a remote reservoir is often the durable fix for a chronic site.
Perform a free chlorine conversion (a "breakpoint burnout"). Stop the ammonia feed and raise the chlorine dose above the breakpoint so free chlorine circulates for a period of weeks. This oxidizes nitrite, kills nitrifiers, and burns off biofilm.
Warning
A free chlorine conversion is a controlled event, not a switch you flip. It temporarily raises THM and HAA5 formation, generates taste and odor complaints, can mobilize corrosion products and cause red water , and must be publicly noticed to two groups who are harmed by the change in disinfectant chemistry: dialysis facilities and owners of fish, reptiles, and aquatic exhibits . Both chloramine and free chlorine must be removed from dialysis water and from aquarium water, but the removal method differs - granular activated carbon handles chloramine much more slowly than free chlorine, and dechlorinators dosed for free chlorine are inadequate for chloramine. Notify hospitals, dialysis centers, aquarium owners, and pet stores in advance of any conversion in either direction.
Chloramine-Specific Hazards Operators Must Communicate
Group Hazard Mitigation
Dialysis patients Chloramine crosses the dialysis membrane and causes hemolytic anemia ; ammonia is also toxic Facilities must use appropriately sized carbon beds and test for total chlorine before the dialyzer
Fish, amphibians, reptiles, aquatic exhibits Chloramine is directly toxic and is not removed by standing or aerating water , unlike free chlorine Chloramine-specific conditioner, or carbon filtration
Food processors and breweries Chloramine survives boiling and imparts off-flavors Carbon treatment
Rubber and elastomer plumbing components Chloramine attacks certain natural rubber and older elastomer gaskets Use chloramine-resistant materials
Operators are the people who take these calls. Knowing that boiling and standing do not remove chloramine while both eventually remove free chlorine is a frequently tested distinction.