Study guide
5.8 Corrosion Control Treatment & Water Stability
California Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: California Water Regulatory Framework & Certification Ladders
1.1 State Water Board & Regional Boards Structure 1.2 Drinking Water Certification: T1-T5 & D1-D5 Requirements 1.3 Wastewater Certification: Grades I-V & OIT Requirements 1.4 Safe Drinking Water Standards, MCLs & Emerging Contaminants 1.5 California Waterworks Standards (Title 22, Chapter 16) 1.6 Public Water System Types, Permits & the Sanitary Survey
2 Chapter 2: California Water Rights, Title 22 & Environmental Policy
2.1 California Title 22 Recycled Water Standards 2.2 California Environmental Quality Act (CEQA) & Proposition 218 2.3 Water Rights & California Water Resources
3 Chapter 3: Drinking Water Source Quality & Coagulation/Flocculation
3.1 Source Water Quality & Watershed Management 3.2 Coagulation Chemistry & Flash Mixing 3.3 Flocculation & Jar Testing 3.4 Wells, Aquifers & Groundwater Hydraulics 3.5 Raw Water Storage, Clearwells & Reservoir Management
4 Chapter 4: Clarification & Granular Media Filtration
4.1 Sedimentation & Advanced Clarification 4.2 Granular Media Filtration Mechanics & Media Types 4.3 Filter Operation, Backwash Cycles & SWTR Compliance
5 Chapter 5: Disinfection, Oxidation & Advanced Water Treatment
5.1 Chlorination Chemistry & Breakpoint Curves 5.2 Disinfection Kinetics & CT Calculations 5.3 Alternative Disinfection: Ozone, UV & Chlorine Dioxide 5.4 Advanced Treatment: Membranes, AOP & PFAS Adsorption 5.5 Chloramination & Nitrification Control 5.6 Iron & Manganese Removal 5.7 Fluoridation Practice & Compliance 5.8 Corrosion Control Treatment & Water Stability 5.9 Taste & Odor Control and Algal Toxin Management
6 Chapter 6: Wastewater Preliminary & Primary Treatment
6.1 Preliminary Treatment: Screening & Grit Removal 6.2 Primary Clarification Operations 6.3 Primary Sludge Characteristics & Pumping 6.4 Stabilization Ponds, Lagoons & Small-Plant Processes
7 Chapter 7: Secondary Biological Treatment & Activated Sludge
7.1 Activated Sludge Process Fundamentals 7.2 Process Control Parameters: F/M, MCRT & SVI 7.3 Activated Sludge Microbiology & Troubleshooting 7.4 Fixed-Film & Hybrid Biological Processes
8 Chapter 8: Biological Nutrient Removal, Water Reuse & Solids Handling
8.1 Biological Nitrogen Removal: Nitrification & Denitrification 8.2 Biological Phosphorus Removal (EBPR) & Chemical Precipitation 8.3 Anaerobic & Aerobic Digestion 8.4 Sludge Thickening, Dewatering & Biosolids Disposal 8.5 Wastewater Disinfection: Chlorination, Dechlorination & UV
9 Chapter 9: Distribution Systems, Collection Networks & Hydraulics
9.1 Hydraulics, Pressure & Flow Dynamics 9.2 Centrifugal Pumps, Motors & VFDs 9.3 Distribution Network Infrastructure & Cross-Connection Control 9.4 Wastewater Collection Systems, SSMP & FOG Management
10 Chapter 10: Laboratory Analytics, Safety & Water Math
10.1 Water & Wastewater Laboratory Methods 10.2 Laboratory Quality Assurance & Regulatory Reporting 10.3 Chemical Safety, Hazardous Gases & Confined Space 10.4 Essential Water & Wastewater Math for Operators
11 Chapter 11: Federal & California Drinking Water Rules
11.1 The Revised Total Coliform Rule & Assessments 11.2 The Lead and Copper Rule and Service Line Replacement 11.3 Surface Water Treatment Rules & Log Removal Credit 11.4 Stage 1 & Stage 2 Disinfection Byproduct Rules 11.5 Secondary MCLs, Notification Levels & Response Levels 11.6 Public Notification, Consumer Confidence Reports & Recordkeeping
12 Chapter 12: Distribution System Design, Demand & Hydraulics
12.1 System Layout, Pressure Zones & Distribution Maps 12.2 Water Demand, Peaking Factors & Fire Flow 12.3 Distribution Storage: Types, Sizing & Turnover 12.4 Head Loss, C-Factor & Distribution Hydraulic Calculations 12.5 Water Hammer, Surge Control & Air Management
13 Chapter 13: Distribution Equipment Operation, Maintenance & Inspection
13.1 Valves: Types, Operation & Exercising Programs 13.2 Fire Hydrants: Types, Testing & Maintenance 13.3 Water Meters: Types, Accuracy & Meter Management 13.4 Instrumentation, In-Line Sensors, Telemetry & SCADA 13.5 Electrical Systems, Motors & Standby Generators 13.6 External Corrosion, Cathodic Protection & Asset Inspection
14 Chapter 14: Water Mains, Piping & Field Construction
14.1 Pipe Materials & Pipe Selection 14.2 Joints, Fittings, Thrust Restraint & Bedding 14.3 Main Installation, Tapping & Service Line Installation 14.4 Leak Detection, Water Loss Auditing & Main Repair 14.5 Main Cleaning & Maintenance: Flushing, Pigging & Lining 14.6 Excavation, Trench Safety & Utility Locating
15 Chapter 15: Disinfecting Distribution Facilities & Maintaining Water Quality
15.1 Water Main Disinfection (AWWA C651) 15.2 Disinfecting Storage Reservoirs (C652) & Wells (C654) 15.3 Maintaining Distribution Water Quality: Residual, Biofilm & Discolored Water 15.4 Cross-Connection Control Program Administration & Device Testing
16 Chapter 16: Plant Equipment, Chemical Feed & Maintenance
16.1 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 16.2 Gas Chlorination Equipment & Hypochlorite Systems 16.3 Blowers, Compressors & Aeration Equipment 16.4 Flow Measurement Devices: Meters, Weirs & Flumes 16.5 Preventive Maintenance, CMMS & Asset Management
17 Chapter 17: Utility Management, Administration & Emergency Response
17.1 Planning, Organizing, Directing & Controlling a Utility Work Group 17.2 Budgets, Water Rates & Financial Management 17.3 Operator Training, Staffing & Safety Program Development 17.4 Energy Management & Optimization 17.5 Emergency Response Planning, Risk & Resilience & Security 17.6 Water Conservation Planning & Drought Response
18 Chapter 18: Applied Operator Mathematics Workshop
18.1 The Exam Conversion Sheet, Units & Dimensional Analysis 18.2 Distribution & Hydraulic Math Workshop 18.3 Treatment & Wastewater Process Math Workshop
5.8 Corrosion Control Treatment & Water Stability
Key Takeaways Explain This Topic AI
Corrosion Control is a named sub-topic on the treatment exam and Corrosion and Corrosivity are named sub-topics in two separate distribution exam categories.
The Langelier Saturation Index is the measured pH minus the calcium carbonate saturation pH, where a positive value indicates scale-forming water and a negative value indicates corrosive water.
The three corrosion control strategies are pH and alkalinity adjustment, inhibitor addition using orthophosphate or silicate, and calcium carbonate precipitation.
Orthophosphate forms a low-solubility lead phosphate scale and is the most widely used corrosion control treatment for lead and copper in California.
Galvanic corrosion between dissimilar metals, such as a lead goose-neck bonded to new copper, accelerates release of the less noble metal and is a reason partial lead service line replacement is disfavored.
Last updated: September 2026
Why Corrosion Control Is an Operator Responsibility
The Expected Range of Knowledge lists Corrosion Control in the treatment Water Treatment Processes category and lists Corrosion (Equipment Operation/Maintenance) and Corrosivity (Water Quality/Water Sources) as separate distribution sub-topics. Corrosion is also the mechanism behind the entire Lead and Copper Rule: lead in drinking water almost never comes from the source; it comes from the plumbing , and how much of it dissolves is a function of finished water chemistry that the operator controls.
Corrosion costs show up four ways: metals in the water (lead, copper, iron, zinc), loss of pipe (main breaks, pinholes, tuberculation), loss of hydraulic capacity (a tuberculated main can lose half its C-factor), and customer complaints (red water, blue-green staining, metallic taste).
The Electrochemistry
Corrosion is an electrochemical cell with four required parts. Break any one and corrosion stops.
- Component Role In a water main
- Anode Metal oxidizes and dissolves; electrons released The pit, the scratch, the less noble metal
- Cathode Electrons consumed, typically reducing oxygen The surrounding intact surface
- Electrolyte Ion path The water itself; conductivity accelerates it
Metallic path Electron path The pipe wall or a bonding wire Anode: Fe → Fe 2 + + 2 e − Cathode: O 2 + 2 H 2 O + 4 e − → 4 OH − \text{Anode: Fe} \rightarrow \text{Fe}^{2+} + 2e^{-} \qquad \text{Cathode: O}_2 + 2\text{H}_2\text{O} + 4e^{-} \rightarrow 4\text{OH}^{-} Anode: Fe → Fe 2 + + 2 e − Cathode: O 2 + 2 H 2 O + 4 e − → 4 OH −
Factors That Increase Corrosion Rate
- Factor Effect
- Low pH Hydrogen ions strip protective scale; strongly increases lead and copper solubility
- Low alkalinity Poor buffering, so pH swings; less carbonate available to build protective scale
- High dissolved oxygen Supplies the cathodic reaction
- High temperature Roughly doubles reaction rate every 10 °C - hot water lines corrode faster
- High velocity Erosion corrosion, especially in copper above about 5-8 ft/s
- High total dissolved solids / conductivity Better electrolyte
High chloride and sulfate relative to alkalinity The Larson ratio ; chloride and sulfate are aggressive to iron and to lead solder
- Free chlorine vs chloramine Changes oxidation-reduction potential and can destabilize existing scale
- Dissimilar metals in contact Galvanic cell
- Microbial activity Microbiologically influenced corrosion under tubercles and biofilm
- Saturation Indices
Langelier Saturation Index (LSI) LSI = pH actual − pH s \text{LSI} = \text{pH}_{\text{actual}} - \text{pH}_{s} LSI = pH actual − pH s
where pH_s is the pH at which the water would be exactly saturated with calcium carbonate, computed from calcium hardness, total alkalinity, total dissolved solids, and temperature .
- LSI Interpretation
- Positive (> 0) Supersaturated - water tends to deposit calcium carbonate scale
- Zero At equilibrium - neither dissolving nor depositing
- Negative (< 0) Undersaturated - water tends to dissolve calcium carbonate , i.e. it is corrosive
Many systems target a slightly positive LSI, roughly +0.2 to +0.5 , to encourage a thin protective film without scaling heat exchangers and meters.
Important
LSI is a directional indicator, not a corrosion rate. It tells you whether calcium carbonate will dissolve or deposit. It says nothing about lead or copper solubility in a low-calcium water, and a positive LSI does not guarantee lead control. This is why the Lead and Copper Rule requires demonstrated optimal corrosion control treatment based on actual tap monitoring rather than on an index value.
Related Indices
Ryznar Stability Index (RSI) = 2pH_s − pH. Below about 6 indicates scaling; above about 7 indicates corrosive; above 8.5 strongly corrosive. Note that the RSI scale runs the opposite direction from LSI , which is a reliable exam trap.
Aggressive Index (AI) = pH + log(alkalinity × calcium hardness). Used for asbestos-cement pipe; below 10 is highly aggressive, 10-12 moderately, above 12 non-aggressive.
Calcium Carbonate Precipitation Potential (CCPP) quantifies how much CaCO₃ in mg/L would precipitate or dissolve, which is more useful operationally than LSI's yes/no direction.
Larson Ratio = (chloride + sulfate) / alkalinity, in equivalents. Above about 0.5 indicates water aggressive to iron.
- The Three Corrosion Control Strategies
- 1. pH and Alkalinity Adjustment
The cheapest and often the most effective lever. Raising pH into the 7.5 to 8.5 range and raising alkalinity to at least 30 to 60 mg/L as CaCO₃ greatly reduces lead and copper solubility and stabilizes the pH so it does not drift in the distribution system.
Chemical Raises pH Raises alkalinity Adds calcium Notes
Sodium hydroxide (caustic soda) Yes Yes No Fast, precise; freezes near 12 °C at 50% strength; strong caustic hazard
- Soda ash (sodium carbonate) Yes Yes No Easier handling than caustic; adds sodium
- Lime (calcium hydroxide/oxide) Yes Yes Yes Adds calcium hardness; slurry feed, scaling and housekeeping issues
- Sodium bicarbonate Slightly Yes No Adds buffer capacity with minimal pH change
- Limestone contactor / calcite Yes Yes Yes Passive, self-limiting; good for small systems
- CO₂ stripping (aeration) Yes No No Removes carbonic acid; free where aeration already exists
- 2. Corrosion Inhibitors
Orthophosphate (phosphoric acid, zinc orthophosphate, sodium orthophosphate) is the workhorse. It forms a low-solubility lead orthophosphate and copper orthophosphate scale on the pipe wall. Typical residual 0.5 to 3.0 mg/L as PO₄ , held continuously - the film takes weeks to months to build and dissolves if the feed stops. Effective across a wide pH range but works best at pH 7.2 to 7.8 .
Blended ortho-polyphosphate provides both film formation and sequestration of iron and manganese, but the polyphosphate fraction can strip existing scale if the blend or dose is wrong.
Sodium silicate raises pH and forms a silicate film; used where phosphorus discharge to a wastewater plant is a concern, since orthophosphate fed to the drinking water system eventually arrives at the wastewater plant and increases its phosphorus load.
Zinc orthophosphate adds zinc, which helps in some waters but raises the zinc load on the receiving wastewater plant.
3. Calcium Carbonate Precipitation
Deliberately operating at a modest positive CCPP so a thin calcium carbonate layer forms. Effective in hard waters; ineffective in soft, low-calcium waters, and risky where scaling would foul meters and heat exchangers.
Field Diagnosis
Symptom Mechanism Typical response
Red water , rusty staining, higher iron at the tap than at the plant Iron corrosion and tubercle release in unlined cast iron Raise pH/alkalinity, orthophosphate, unidirectional flushing, main lining or replacement
Blue-green staining of fixtures, metallic taste Copper corrosion, usually acidic and low-alkalinity water, aggravated by high temperature Raise pH to 7.5-8.0, raise alkalinity, orthophosphate
Pinhole leaks in copper , usually cold-water lines Pitting corrosion, sometimes chloride- or microbially driven Water chemistry adjustment; investigate velocity and grounding
Elevated lead only at some homes Lead service lines, lead solder, or brass fixtures at those addresses Optimal corrosion control treatment, service line inventory and replacement
Loss of C-factor and pressure in old mains Tuberculation Cleaning and lining, or replacement
Localized deep pitting near an electrical service Stray current corrosion Investigate grounding and cathodic interference
Accelerated attack at a lead-to-copper joint Galvanic corrosion Avoid dissimilar metal contact; use dielectric unions
Warning
Partial lead service line replacement can make lead levels worse. Cutting a lead line and connecting new copper creates a galvanic couple in which the lead becomes the anode, and the physical disturbance also releases accumulated scale. This is the technical reason regulators now push full service line replacement rather than partial replacement, and the reason customers must be given flushing instructions and a filter after any service line work.