Study guide

5.6 Iron & Manganese Removal

California Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: California Water Regulatory Framework & Certification Ladders

1.1 State Water Board & Regional Boards Structure 1.2 Drinking Water Certification: T1-T5 & D1-D5 Requirements 1.3 Wastewater Certification: Grades I-V & OIT Requirements 1.4 Safe Drinking Water Standards, MCLs & Emerging Contaminants 1.5 California Waterworks Standards (Title 22, Chapter 16) 1.6 Public Water System Types, Permits & the Sanitary Survey

2 Chapter 2: California Water Rights, Title 22 & Environmental Policy

2.1 California Title 22 Recycled Water Standards 2.2 California Environmental Quality Act (CEQA) & Proposition 218 2.3 Water Rights & California Water Resources

3 Chapter 3: Drinking Water Source Quality & Coagulation/Flocculation

3.1 Source Water Quality & Watershed Management 3.2 Coagulation Chemistry & Flash Mixing 3.3 Flocculation & Jar Testing 3.4 Wells, Aquifers & Groundwater Hydraulics 3.5 Raw Water Storage, Clearwells & Reservoir Management

4 Chapter 4: Clarification & Granular Media Filtration

4.1 Sedimentation & Advanced Clarification 4.2 Granular Media Filtration Mechanics & Media Types 4.3 Filter Operation, Backwash Cycles & SWTR Compliance

5 Chapter 5: Disinfection, Oxidation & Advanced Water Treatment

5.1 Chlorination Chemistry & Breakpoint Curves 5.2 Disinfection Kinetics & CT Calculations 5.3 Alternative Disinfection: Ozone, UV & Chlorine Dioxide 5.4 Advanced Treatment: Membranes, AOP & PFAS Adsorption 5.5 Chloramination & Nitrification Control 5.6 Iron & Manganese Removal 5.7 Fluoridation Practice & Compliance 5.8 Corrosion Control Treatment & Water Stability 5.9 Taste & Odor Control and Algal Toxin Management

6 Chapter 6: Wastewater Preliminary & Primary Treatment

6.1 Preliminary Treatment: Screening & Grit Removal 6.2 Primary Clarification Operations 6.3 Primary Sludge Characteristics & Pumping 6.4 Stabilization Ponds, Lagoons & Small-Plant Processes

7 Chapter 7: Secondary Biological Treatment & Activated Sludge

7.1 Activated Sludge Process Fundamentals 7.2 Process Control Parameters: F/M, MCRT & SVI 7.3 Activated Sludge Microbiology & Troubleshooting 7.4 Fixed-Film & Hybrid Biological Processes

8 Chapter 8: Biological Nutrient Removal, Water Reuse & Solids Handling

8.1 Biological Nitrogen Removal: Nitrification & Denitrification 8.2 Biological Phosphorus Removal (EBPR) & Chemical Precipitation 8.3 Anaerobic & Aerobic Digestion 8.4 Sludge Thickening, Dewatering & Biosolids Disposal 8.5 Wastewater Disinfection: Chlorination, Dechlorination & UV

9 Chapter 9: Distribution Systems, Collection Networks & Hydraulics

9.1 Hydraulics, Pressure & Flow Dynamics 9.2 Centrifugal Pumps, Motors & VFDs 9.3 Distribution Network Infrastructure & Cross-Connection Control 9.4 Wastewater Collection Systems, SSMP & FOG Management

10 Chapter 10: Laboratory Analytics, Safety & Water Math

10.1 Water & Wastewater Laboratory Methods 10.2 Laboratory Quality Assurance & Regulatory Reporting 10.3 Chemical Safety, Hazardous Gases & Confined Space 10.4 Essential Water & Wastewater Math for Operators

11 Chapter 11: Federal & California Drinking Water Rules

11.1 The Revised Total Coliform Rule & Assessments 11.2 The Lead and Copper Rule and Service Line Replacement 11.3 Surface Water Treatment Rules & Log Removal Credit 11.4 Stage 1 & Stage 2 Disinfection Byproduct Rules 11.5 Secondary MCLs, Notification Levels & Response Levels 11.6 Public Notification, Consumer Confidence Reports & Recordkeeping

12 Chapter 12: Distribution System Design, Demand & Hydraulics

12.1 System Layout, Pressure Zones & Distribution Maps 12.2 Water Demand, Peaking Factors & Fire Flow 12.3 Distribution Storage: Types, Sizing & Turnover 12.4 Head Loss, C-Factor & Distribution Hydraulic Calculations 12.5 Water Hammer, Surge Control & Air Management

13 Chapter 13: Distribution Equipment Operation, Maintenance & Inspection

13.1 Valves: Types, Operation & Exercising Programs 13.2 Fire Hydrants: Types, Testing & Maintenance 13.3 Water Meters: Types, Accuracy & Meter Management 13.4 Instrumentation, In-Line Sensors, Telemetry & SCADA 13.5 Electrical Systems, Motors & Standby Generators 13.6 External Corrosion, Cathodic Protection & Asset Inspection

14 Chapter 14: Water Mains, Piping & Field Construction

14.1 Pipe Materials & Pipe Selection 14.2 Joints, Fittings, Thrust Restraint & Bedding 14.3 Main Installation, Tapping & Service Line Installation 14.4 Leak Detection, Water Loss Auditing & Main Repair 14.5 Main Cleaning & Maintenance: Flushing, Pigging & Lining 14.6 Excavation, Trench Safety & Utility Locating

15 Chapter 15: Disinfecting Distribution Facilities & Maintaining Water Quality

15.1 Water Main Disinfection (AWWA C651) 15.2 Disinfecting Storage Reservoirs (C652) & Wells (C654) 15.3 Maintaining Distribution Water Quality: Residual, Biofilm & Discolored Water 15.4 Cross-Connection Control Program Administration & Device Testing

16 Chapter 16: Plant Equipment, Chemical Feed & Maintenance

16.1 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 16.2 Gas Chlorination Equipment & Hypochlorite Systems 16.3 Blowers, Compressors & Aeration Equipment 16.4 Flow Measurement Devices: Meters, Weirs & Flumes 16.5 Preventive Maintenance, CMMS & Asset Management

17 Chapter 17: Utility Management, Administration & Emergency Response

17.1 Planning, Organizing, Directing & Controlling a Utility Work Group 17.2 Budgets, Water Rates & Financial Management 17.3 Operator Training, Staffing & Safety Program Development 17.4 Energy Management & Optimization 17.5 Emergency Response Planning, Risk & Resilience & Security 17.6 Water Conservation Planning & Drought Response

18 Chapter 18: Applied Operator Mathematics Workshop

18.1 The Exam Conversion Sheet, Units & Dimensional Analysis 18.2 Distribution & Hydraulic Math Workshop 18.3 Treatment & Wastewater Process Math Workshop

5.6 Iron & Manganese Removal

Key Takeaways Explain This Topic AI

Iron has a California secondary MCL of 0.3 mg/L and manganese 0.05 mg/L, both consumer acceptance standards driven by staining, color, and taste.

Soluble ferrous iron and manganous manganese must be oxidized to insoluble ferric hydroxide and manganese dioxide before they can be filtered out.

Manganese oxidizes far more slowly than iron with chlorine and generally requires a higher pH, permanganate, ozone, or a catalytic manganese dioxide filter surface.

Sequestration with polyphosphate or silicate holds low concentrations in solution but does not remove the metals and fails above roughly 1 mg/L iron or 0.1 mg/L manganese, and it is defeated by heating.

Greensand and manganese dioxide coated media work by catalytic oxidation at the grain surface and require either continuous or intermittent regeneration.

Last updated: September 2026

The Regulatory Driver

Iron and manganese are secondary contaminants in California, regulated under 22 CCR 64449 as consumer acceptance contaminant levels:

  • Constituent California Secondary MCL
  • Iron 0.3 mg/L
  • Manganese 0.05 mg/L
  • Color 15 units
  • Odor - threshold 3 units
  • Turbidity 5 units
  • Total dissolved solids Recommended 500, upper 1,000, short term 1,500 mg/L

Secondary standards protect taste, odor, and appearance rather than health, but they generate the majority of customer complaints and they are enforceable in California - a system exceeding a secondary MCL must notify the State Board and its customers and develop a plan. Manganese in particular has received increased health attention in recent years and carries a health-based notification level well below levels that cause obvious black water.

Why the low thresholds? At 0.3 mg/L iron water begins to stain laundry and fixtures reddish-brown and taste metallic. At 0.05 mg/L manganese the staining is black to purple-black, and manganese deposits accumulate in mains for years before releasing as a slug of black water during a hydrant flow or a velocity change.

The Underlying Chemistry

Both metals are soluble in their reduced states and insoluble in their oxidized states. Removal is therefore always the same two-step sequence: oxidize, then filter.

Metal Soluble (reduced) form Insoluble (oxidized) form

Iron Fe²⁺ (ferrous) - clear water at the tap that turns rusty after standing Fe(OH)₃ (ferric hydroxide) - reddish-brown floc

Manganese Mn²⁺ (manganous) - clear MnO₂ (manganese dioxide) - black precipitate

The tell-tale field observation is water that is clear at the tap and colored after sitting in a glass . That is dissolved reduced metal oxidizing on contact with air, and it means the source contains soluble Fe or Mn that treatment did not oxidize.

Manganese is much harder than iron. Ferrous iron oxidizes with chlorine in minutes at pH 7. Manganese oxidation with chlorine is slow below about pH 9.5 and can take an hour or more. That single fact drives almost every design decision in this topic.

Oxidant Stoichiometry

  • Oxidant mg required per mg Fe²⁺ mg required per mg Mn²⁺ Notes
  • Chlorine (Cl₂) 0.62 1.30 Cheap; manganese needs high pH and long contact
  • Potassium permanganate (KMnO₄) 0.94 1.92 Works across a wide pH range; overdose turns water pink
  • Ozone (O₃) 0.43 0.88 Fast and effective; overdose oxidizes Mn to permanganate , producing pink water
  • Oxygen (aeration) 0.14 0.29 Effective for iron; very slow for manganese below pH 9.5
  • Chlorine dioxide (ClO₂) 1.21 2.45 Effective; chlorite byproduct is regulated

Important

Two pink-water traps. Overdosing permanganate leaves unreacted MnO₄⁻ and the water arrives pink. Overdosing ozone oxidizes manganese all the way past MnO₂ to permanganate - and the water also arrives pink. In both cases the fix is to reduce the oxidant dose, and in both cases the pink color is a warning that unfiltered manganese is entering the distribution system.

  • Removal Processes
  • 1. Oxidation and Filtration (the standard train)

Feed oxidant at the wellhead or plant influent, allow a detention/reaction basin, then filter through dual media, greensand, or a manganese dioxide coated medium. Detention requirements differ sharply: iron may need only 5 to 10 minutes, while manganese with chlorine may need 30 to 60 minutes or a raised pH.

2. Aeration and Filtration

Cascade trays, spray aerators, packed towers, or induced-draft aerators transfer oxygen and simultaneously strip hydrogen sulfide and carbon dioxide. Stripping CO₂ raises pH , which helps manganese oxidation. Aeration alone is generally adequate for iron and inadequate for manganese, so aeration plants that also need manganese removal add a chemical oxidant.

3. Manganese Greensand

Glauconite sand coated with manganese dioxide . The MnO₂ coating oxidizes Fe²⁺ and Mn²⁺ on contact - the medium is both a catalyst and an oxidant sink - and is regenerated by permanganate. Two operating modes:

Intermittent regeneration (batch): the bed is taken offline and soaked with a permanganate solution, then rinsed to waste until the rinse runs clear. Missing a regeneration allows manganese breakthrough.

Continuous regeneration (CR): permanganate is fed continuously ahead of the filter so the coating is renewed in service. The dose must be trimmed carefully - too little and manganese breaks through, too much and the filtrate is pink.

Greensand is pH sensitive (generally 6.2 to 8.5) and can be damaged by strong oxidants or by chlorine-free operation that strips the coating.

4. Manganese Dioxide Coated Media / Catalytic Filtration

Modern MnO₂-coated anthracite or ceramic media operate on the same catalytic principle but tolerate a wider pH range and higher loading rates, and are regenerated by the free chlorine residual carried through the bed. These media are common retrofits at California groundwater plants that need manganese removal without a permanganate feed system.

5. Biological Filtration

Iron and manganese oxidizing bacteria ( Gallionella , Leptothrix , Crenothrix ) can be cultivated on a filter bed and will remove both metals at low oxidant demand. Biological beds need careful dissolved oxygen and pH control and no free chlorine ahead of the filter, which conflicts with disinfection strategy at many plants.

6. Sequestration (control, not removal)

Polyphosphate or sodium silicate complexes the reduced metal and keeps it dissolved so it does not precipitate and stain. Critically:

It does not remove the metal - total iron and manganese leaving the plant are unchanged.

It is effective only at low concentrations , generally up to about 1.0 mg/L iron and 0.1 mg/L manganese .

Heating breaks the complex. Water that looked fine at the tap turns rusty or black in a water heater, dishwasher, or coffee maker.

Chlorine competes with the sequestrant; feeding chlorine before the polyphosphate defeats the treatment. Feed the sequestrant first , then the disinfectant.

Polyphosphate adds phosphorus, which can support biofilm growth in the distribution system.

Tip

Exam framing. When a question offers sequestration for a source at 2.5 mg/L iron, sequestration is the wrong answer - it is above the practical limit. When a question describes clear water that blackens only in the water heater, sequestration that is failing on heating is the right diagnosis.

Distribution System Consequences

Iron and manganese that escape treatment do not disappear; they accumulate on pipe walls as a loose deposit for months or years. Then a velocity change - a hydrant flow, a fire, a pump start, a valve operation, a main break - resuspends the deposit and produces:

  • Red water (iron), typically after a velocity increase in unlined cast iron mains
  • Black water (manganese), often much more alarming to customers because the color is so dark
  • Turbidity and color complaints clustered downstream of the disturbance
  • Increased chlorine demand , because reduced metals consume disinfectant

Prevention beats response: keep finished water iron below 0.3 and manganese well below 0.05 mg/L, and run a unidirectional flushing program that mobilizes and removes deposits at controlled velocities on a planned schedule rather than letting a fire flow do it at 3 a.m.

Worked dose example. A groundwater source contains 0.85 mg/L Fe²⁺ and 0.22 mg/L Mn²⁺ and will be treated with potassium permanganate.

Iron demand = 0.85 x 0.94 = 0.80 mg/L.

Manganese demand = 0.22 x 1.92 = 0.42 mg/L.

Theoretical permanganate dose = 0.80 + 0.42 = 1.22 mg/L , before adding any demand exerted by organics or sulfide. Confirm by bench test and trim to the point where filtrate manganese is non-detect without pink color.