Study guide

12.2 Water Demand, Peaking Factors & Fire Flow

California Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: California Water Regulatory Framework & Certification Ladders

1.1 State Water Board & Regional Boards Structure 1.2 Drinking Water Certification: T1-T5 & D1-D5 Requirements 1.3 Wastewater Certification: Grades I-V & OIT Requirements 1.4 Safe Drinking Water Standards, MCLs & Emerging Contaminants 1.5 California Waterworks Standards (Title 22, Chapter 16) 1.6 Public Water System Types, Permits & the Sanitary Survey

2 Chapter 2: California Water Rights, Title 22 & Environmental Policy

2.1 California Title 22 Recycled Water Standards 2.2 California Environmental Quality Act (CEQA) & Proposition 218 2.3 Water Rights & California Water Resources

3 Chapter 3: Drinking Water Source Quality & Coagulation/Flocculation

3.1 Source Water Quality & Watershed Management 3.2 Coagulation Chemistry & Flash Mixing 3.3 Flocculation & Jar Testing 3.4 Wells, Aquifers & Groundwater Hydraulics 3.5 Raw Water Storage, Clearwells & Reservoir Management

4 Chapter 4: Clarification & Granular Media Filtration

4.1 Sedimentation & Advanced Clarification 4.2 Granular Media Filtration Mechanics & Media Types 4.3 Filter Operation, Backwash Cycles & SWTR Compliance

5 Chapter 5: Disinfection, Oxidation & Advanced Water Treatment

5.1 Chlorination Chemistry & Breakpoint Curves 5.2 Disinfection Kinetics & CT Calculations 5.3 Alternative Disinfection: Ozone, UV & Chlorine Dioxide 5.4 Advanced Treatment: Membranes, AOP & PFAS Adsorption 5.5 Chloramination & Nitrification Control 5.6 Iron & Manganese Removal 5.7 Fluoridation Practice & Compliance 5.8 Corrosion Control Treatment & Water Stability 5.9 Taste & Odor Control and Algal Toxin Management

6 Chapter 6: Wastewater Preliminary & Primary Treatment

6.1 Preliminary Treatment: Screening & Grit Removal 6.2 Primary Clarification Operations 6.3 Primary Sludge Characteristics & Pumping 6.4 Stabilization Ponds, Lagoons & Small-Plant Processes

7 Chapter 7: Secondary Biological Treatment & Activated Sludge

7.1 Activated Sludge Process Fundamentals 7.2 Process Control Parameters: F/M, MCRT & SVI 7.3 Activated Sludge Microbiology & Troubleshooting 7.4 Fixed-Film & Hybrid Biological Processes

8 Chapter 8: Biological Nutrient Removal, Water Reuse & Solids Handling

8.1 Biological Nitrogen Removal: Nitrification & Denitrification 8.2 Biological Phosphorus Removal (EBPR) & Chemical Precipitation 8.3 Anaerobic & Aerobic Digestion 8.4 Sludge Thickening, Dewatering & Biosolids Disposal 8.5 Wastewater Disinfection: Chlorination, Dechlorination & UV

9 Chapter 9: Distribution Systems, Collection Networks & Hydraulics

9.1 Hydraulics, Pressure & Flow Dynamics 9.2 Centrifugal Pumps, Motors & VFDs 9.3 Distribution Network Infrastructure & Cross-Connection Control 9.4 Wastewater Collection Systems, SSMP & FOG Management

10 Chapter 10: Laboratory Analytics, Safety & Water Math

10.1 Water & Wastewater Laboratory Methods 10.2 Laboratory Quality Assurance & Regulatory Reporting 10.3 Chemical Safety, Hazardous Gases & Confined Space 10.4 Essential Water & Wastewater Math for Operators

11 Chapter 11: Federal & California Drinking Water Rules

11.1 The Revised Total Coliform Rule & Assessments 11.2 The Lead and Copper Rule and Service Line Replacement 11.3 Surface Water Treatment Rules & Log Removal Credit 11.4 Stage 1 & Stage 2 Disinfection Byproduct Rules 11.5 Secondary MCLs, Notification Levels & Response Levels 11.6 Public Notification, Consumer Confidence Reports & Recordkeeping

12 Chapter 12: Distribution System Design, Demand & Hydraulics

12.1 System Layout, Pressure Zones & Distribution Maps 12.2 Water Demand, Peaking Factors & Fire Flow 12.3 Distribution Storage: Types, Sizing & Turnover 12.4 Head Loss, C-Factor & Distribution Hydraulic Calculations 12.5 Water Hammer, Surge Control & Air Management

13 Chapter 13: Distribution Equipment Operation, Maintenance & Inspection

13.1 Valves: Types, Operation & Exercising Programs 13.2 Fire Hydrants: Types, Testing & Maintenance 13.3 Water Meters: Types, Accuracy & Meter Management 13.4 Instrumentation, In-Line Sensors, Telemetry & SCADA 13.5 Electrical Systems, Motors & Standby Generators 13.6 External Corrosion, Cathodic Protection & Asset Inspection

14 Chapter 14: Water Mains, Piping & Field Construction

14.1 Pipe Materials & Pipe Selection 14.2 Joints, Fittings, Thrust Restraint & Bedding 14.3 Main Installation, Tapping & Service Line Installation 14.4 Leak Detection, Water Loss Auditing & Main Repair 14.5 Main Cleaning & Maintenance: Flushing, Pigging & Lining 14.6 Excavation, Trench Safety & Utility Locating

15 Chapter 15: Disinfecting Distribution Facilities & Maintaining Water Quality

15.1 Water Main Disinfection (AWWA C651) 15.2 Disinfecting Storage Reservoirs (C652) & Wells (C654) 15.3 Maintaining Distribution Water Quality: Residual, Biofilm & Discolored Water 15.4 Cross-Connection Control Program Administration & Device Testing

16 Chapter 16: Plant Equipment, Chemical Feed & Maintenance

16.1 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 16.2 Gas Chlorination Equipment & Hypochlorite Systems 16.3 Blowers, Compressors & Aeration Equipment 16.4 Flow Measurement Devices: Meters, Weirs & Flumes 16.5 Preventive Maintenance, CMMS & Asset Management

17 Chapter 17: Utility Management, Administration & Emergency Response

17.1 Planning, Organizing, Directing & Controlling a Utility Work Group 17.2 Budgets, Water Rates & Financial Management 17.3 Operator Training, Staffing & Safety Program Development 17.4 Energy Management & Optimization 17.5 Emergency Response Planning, Risk & Resilience & Security 17.6 Water Conservation Planning & Drought Response

18 Chapter 18: Applied Operator Mathematics Workshop

18.1 The Exam Conversion Sheet, Units & Dimensional Analysis 18.2 Distribution & Hydraulic Math Workshop 18.3 Treatment & Wastewater Process Math Workshop

12.2 Water Demand, Peaking Factors & Fire Flow

Key Takeaways Explain This Topic AI

Assess System Demand is a named sub-topic in the SWRCB distribution Expected Range of Knowledge.

Maximum day demand is typically 1.5 to 2.5 times average day demand, and peak hour demand is typically 2 to 4 times average day demand.

Under 22 CCR 64554 a system with 1,000 or more service connections must meet four hours of peak hourly demand from source capacity, storage, or emergency connections.

Fire flow is expressed in gallons per minute for a stated duration at a residual pressure of at least 20 psi, and it is supplied primarily from storage, not from source capacity.

The controlling design condition for most systems is maximum day demand plus fire flow, evaluated against the 20 psi residual pressure floor.

Last updated: September 2026

Demand Terminology

  • Term Definition Typical multiplier of ADD
  • Average day demand (ADD) Total annual volume divided by 365 1.0
  • Maximum day demand (MDD) The highest single day of the year 1.5 to 2.5
  • Peak hour demand (PHD) The highest single hour of the year 2.0 to 4.0 (often 1.5 to 2.0 times MDD)
  • Minimum hour demand The lowest hour, typically 3-5 a.m. 0.2 to 0.4
  • Fire flow Rate required to fight a design fire, for a stated duration Additive to MDD

In California these factors are wider than in most states because of climate. A Central Valley system with heavy summer landscape irrigation can see an MDD three times its winter average, while a coastal system with year-round mild weather may see 1.4. Know your own system's factors from your own meter and production data - that is exactly what 22 CCR 64554 requires.

The 22 CCR 64554 Method

  • Data available MDD method Minimum peaking factor
  • Daily usage data Highest usage day in the past 10 years 1.5
  • Monthly usage data Derived from the maximum month 1.5
  • Annual usage data only Highest-use year / 365 2.25
  • No usage data Comparable systems of similar size, elevation, climate, demographics -

And the capacity tests:

All systems: sources must be able to meet MDD at all times , evaluated system-wide and within each pressure zone .

1,000 or more service connections: must meet four hours of peak hourly demand from source capacity, storage, or emergency connections.

Fewer than 1,000 service connections: storage capacity must equal or exceed MDD, unless additional sources or emergency connections are demonstrated.

Community groundwater-only systems: at least two approved sources , able to meet demand with the largest source out of service .

Estimating Demand

Unit demand approach. A residential development of 480 homes at an average of 2.8 persons per home and 110 gallons per capita per day:

ADD = 480 x 2.8 x 110 = 147,840 gpd = 102.7 gpm MDD at a factor of 2.0 = 295,680 gpd = 205 gpm PHD at a factor of 3.5 x ADD = 517,440 gpd = 359 gpm

Equivalent dwelling unit (EDU) approach. Commercial, industrial, and institutional customers are converted to EDUs by meter size or by measured use, then added to the residential count. This is the basis for most California connection fee schedules and for Proposition 218 rate structures.

Fire Flow

Fire flow is expressed as a rate in gpm , for a duration in hours , at a residual pressure of at least 20 psi in the main while flowing. All three parts matter; a system that can deliver 1,500 gpm only by dropping to 12 psi has not met a 1,500 gpm fire flow requirement.

  • Occupancy (illustrative) Typical required fire flow Typical duration
  • Single-family residential, small lots 1,000-1,500 gpm 1-2 hours
  • Multi-family residential 1,500-2,500 gpm 2 hours
  • Commercial 2,500-3,500 gpm 2-3 hours
  • Industrial / warehouse 3,500-8,000 gpm 3-4 hours

Required flows are set by the fire authority having jurisdiction using the California Fire Code and the referenced fire flow tables, adjusted for construction type, occupancy, area, exposure, and the presence of automatic sprinklers , which can reduce required fire flow substantially. Fire Storage (gal) = Required Fire Flow (gpm) × Duration (min) \text{Fire Storage (gal)} = \text{Required Fire Flow (gpm)} \times \text{Duration (min)} Fire Storage (gal) = Required Fire Flow (gpm) × Duration (min)

Example: 2,000 gpm for 2 hours = 2,000 x 120 = 240,000 gallons of dedicated fire storage.

Important

Fire flow comes out of storage, not out of the wells. A source that produces 900 gpm cannot supply a 2,500 gpm fire. The correct design statement is that the system must supply maximum day demand from its sources while simultaneously supplying fire flow from storage , and must recover the fire storage volume within a stated period afterward. Sizing questions that ask "is this source adequate for fire flow" are testing whether you know that fire flow is a storage question.

Hydrant Flow Testing

Flow testing measures what the system can actually deliver:

Select a residual hydrant (where pressure is measured) and one or more flow hydrants (which are opened).

Record static pressure at the residual hydrant with nothing flowing.

Open the flow hydrant(s) and measure discharge using a pitot gauge at the outlet, and record the residual pressure at the residual hydrant.

Compute flow at the outlet, then project the flow available at 20 psi. Q = 29.83 × c × d 2 × p Q = 29.83 \times c \times d^{2} \times \sqrt{p} Q = 29.83 × c × d 2 × p ​

where Q is gpm, c is the outlet coefficient (typically 0.90 for a rounded outlet, 0.80 for a square-edged outlet projecting into the barrel), d is the outlet diameter in inches, and p is the pitot pressure in psi.

Example: a 2.5-inch outlet with c = 0.90 and a pitot reading of 16 psi:

Q = 29.83 x 0.90 x (2.5)² x √16 = 29.83 x 0.90 x 6.25 x 4 = 671 gpm

The available flow at 20 psi is then projected from the static and residual readings using the standard hydrant flow test formula, giving the number the fire authority needs.

Safety and Courtesy During Flow Tests

Notify the fire department and, for large tests, customers - flow tests cause discolored water and pressure drops.

Open and close hydrants slowly. A fast closure is a water hammer generator.

Control the discharge - erosion, flooding, traffic hazards, and dechlorination of the discharge where it reaches a storm drain or watercourse are all real obligations.

Watch the residual pressure floor. If the test would pull the system below 20 psi, stop; you are creating an intrusion risk, not gathering data.