Study guide

12.3 Distribution Storage: Types, Sizing & Turnover

California Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: California Water Regulatory Framework & Certification Ladders

1.1 State Water Board & Regional Boards Structure 1.2 Drinking Water Certification: T1-T5 & D1-D5 Requirements 1.3 Wastewater Certification: Grades I-V & OIT Requirements 1.4 Safe Drinking Water Standards, MCLs & Emerging Contaminants 1.5 California Waterworks Standards (Title 22, Chapter 16) 1.6 Public Water System Types, Permits & the Sanitary Survey

2 Chapter 2: California Water Rights, Title 22 & Environmental Policy

2.1 California Title 22 Recycled Water Standards 2.2 California Environmental Quality Act (CEQA) & Proposition 218 2.3 Water Rights & California Water Resources

3 Chapter 3: Drinking Water Source Quality & Coagulation/Flocculation

3.1 Source Water Quality & Watershed Management 3.2 Coagulation Chemistry & Flash Mixing 3.3 Flocculation & Jar Testing 3.4 Wells, Aquifers & Groundwater Hydraulics 3.5 Raw Water Storage, Clearwells & Reservoir Management

4 Chapter 4: Clarification & Granular Media Filtration

4.1 Sedimentation & Advanced Clarification 4.2 Granular Media Filtration Mechanics & Media Types 4.3 Filter Operation, Backwash Cycles & SWTR Compliance

5 Chapter 5: Disinfection, Oxidation & Advanced Water Treatment

5.1 Chlorination Chemistry & Breakpoint Curves 5.2 Disinfection Kinetics & CT Calculations 5.3 Alternative Disinfection: Ozone, UV & Chlorine Dioxide 5.4 Advanced Treatment: Membranes, AOP & PFAS Adsorption 5.5 Chloramination & Nitrification Control 5.6 Iron & Manganese Removal 5.7 Fluoridation Practice & Compliance 5.8 Corrosion Control Treatment & Water Stability 5.9 Taste & Odor Control and Algal Toxin Management

6 Chapter 6: Wastewater Preliminary & Primary Treatment

6.1 Preliminary Treatment: Screening & Grit Removal 6.2 Primary Clarification Operations 6.3 Primary Sludge Characteristics & Pumping 6.4 Stabilization Ponds, Lagoons & Small-Plant Processes

7 Chapter 7: Secondary Biological Treatment & Activated Sludge

7.1 Activated Sludge Process Fundamentals 7.2 Process Control Parameters: F/M, MCRT & SVI 7.3 Activated Sludge Microbiology & Troubleshooting 7.4 Fixed-Film & Hybrid Biological Processes

8 Chapter 8: Biological Nutrient Removal, Water Reuse & Solids Handling

8.1 Biological Nitrogen Removal: Nitrification & Denitrification 8.2 Biological Phosphorus Removal (EBPR) & Chemical Precipitation 8.3 Anaerobic & Aerobic Digestion 8.4 Sludge Thickening, Dewatering & Biosolids Disposal 8.5 Wastewater Disinfection: Chlorination, Dechlorination & UV

9 Chapter 9: Distribution Systems, Collection Networks & Hydraulics

9.1 Hydraulics, Pressure & Flow Dynamics 9.2 Centrifugal Pumps, Motors & VFDs 9.3 Distribution Network Infrastructure & Cross-Connection Control 9.4 Wastewater Collection Systems, SSMP & FOG Management

10 Chapter 10: Laboratory Analytics, Safety & Water Math

10.1 Water & Wastewater Laboratory Methods 10.2 Laboratory Quality Assurance & Regulatory Reporting 10.3 Chemical Safety, Hazardous Gases & Confined Space 10.4 Essential Water & Wastewater Math for Operators

11 Chapter 11: Federal & California Drinking Water Rules

11.1 The Revised Total Coliform Rule & Assessments 11.2 The Lead and Copper Rule and Service Line Replacement 11.3 Surface Water Treatment Rules & Log Removal Credit 11.4 Stage 1 & Stage 2 Disinfection Byproduct Rules 11.5 Secondary MCLs, Notification Levels & Response Levels 11.6 Public Notification, Consumer Confidence Reports & Recordkeeping

12 Chapter 12: Distribution System Design, Demand & Hydraulics

12.1 System Layout, Pressure Zones & Distribution Maps 12.2 Water Demand, Peaking Factors & Fire Flow 12.3 Distribution Storage: Types, Sizing & Turnover 12.4 Head Loss, C-Factor & Distribution Hydraulic Calculations 12.5 Water Hammer, Surge Control & Air Management

13 Chapter 13: Distribution Equipment Operation, Maintenance & Inspection

13.1 Valves: Types, Operation & Exercising Programs 13.2 Fire Hydrants: Types, Testing & Maintenance 13.3 Water Meters: Types, Accuracy & Meter Management 13.4 Instrumentation, In-Line Sensors, Telemetry & SCADA 13.5 Electrical Systems, Motors & Standby Generators 13.6 External Corrosion, Cathodic Protection & Asset Inspection

14 Chapter 14: Water Mains, Piping & Field Construction

14.1 Pipe Materials & Pipe Selection 14.2 Joints, Fittings, Thrust Restraint & Bedding 14.3 Main Installation, Tapping & Service Line Installation 14.4 Leak Detection, Water Loss Auditing & Main Repair 14.5 Main Cleaning & Maintenance: Flushing, Pigging & Lining 14.6 Excavation, Trench Safety & Utility Locating

15 Chapter 15: Disinfecting Distribution Facilities & Maintaining Water Quality

15.1 Water Main Disinfection (AWWA C651) 15.2 Disinfecting Storage Reservoirs (C652) & Wells (C654) 15.3 Maintaining Distribution Water Quality: Residual, Biofilm & Discolored Water 15.4 Cross-Connection Control Program Administration & Device Testing

16 Chapter 16: Plant Equipment, Chemical Feed & Maintenance

16.1 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 16.2 Gas Chlorination Equipment & Hypochlorite Systems 16.3 Blowers, Compressors & Aeration Equipment 16.4 Flow Measurement Devices: Meters, Weirs & Flumes 16.5 Preventive Maintenance, CMMS & Asset Management

17 Chapter 17: Utility Management, Administration & Emergency Response

17.1 Planning, Organizing, Directing & Controlling a Utility Work Group 17.2 Budgets, Water Rates & Financial Management 17.3 Operator Training, Staffing & Safety Program Development 17.4 Energy Management & Optimization 17.5 Emergency Response Planning, Risk & Resilience & Security 17.6 Water Conservation Planning & Drought Response

18 Chapter 18: Applied Operator Mathematics Workshop

18.1 The Exam Conversion Sheet, Units & Dimensional Analysis 18.2 Distribution & Hydraulic Math Workshop 18.3 Treatment & Wastewater Process Math Workshop

12.3 Distribution Storage: Types, Sizing & Turnover

Key Takeaways Explain This Topic AI

Storage Facilities is a named sub-topic in the Distribution System Design and Hydraulics category of the SWRCB distribution exam.

Total storage is the sum of operating or equalization storage, fire storage, and emergency storage.

An elevated tank or a ground tank at elevation floats on the system and sets the hydraulic grade line; a ground-level tank at grade requires a booster pump station to serve the system.

Water level in feet converts to pressure by multiplying by 0.433, so a tank with 60 feet of water depth develops about 26 psi at its base.

Long detention time in storage causes loss of disinfectant residual, disinfection byproduct formation, nitrification in chloraminated systems, and temperature stratification.

Last updated: September 2026

What Storage Buys

Component Purpose Typical sizing basis

Operating (equalization) storage Absorbs the difference between a steady source or plant output and a fluctuating demand Often 15 to 25 percent of maximum day demand

Fire storage Supplies fire flow at the required rate and duration Required fire flow x duration, per the fire authority

Emergency storage Covers source outage, power failure, main break, earthquake Often 1 day of average demand or a policy-set duration Total Storage = Operating + Fire + Emergency \text{Total Storage} = \text{Operating} + \text{Fire} + \text{Emergency} Total Storage = Operating + Fire + Emergency

Worked example. MDD is 3.0 MGD; fire flow is 3,000 gpm for 3 hours; emergency policy is one average day at 1.6 MGD.

Operating at 20 percent of MDD = 0.20 x 3,000,000 = 600,000 gal Fire = 3,000 x 180 = 540,000 gal Emergency = 1,600,000 gal Total = 2,740,000 gallons

Storage Types and Hydraulic Position

Type Position How it serves the system

Elevated tank (legged or composite) Bowl above the service area Floats on the system - sets the hydraulic grade line directly; supplies flow by gravity during outages

Standpipe Tall ground-supported cylinder Only the volume above the service area elevation is useful storage; the rest is supporting volume

Ground-level reservoir at elevation (hilltop tank) On high ground Floats on the system ; the California norm where terrain allows

Ground-level reservoir at grade / clearwell At plant grade Does not float; requires a booster pump station to deliver to the system

Buried or partially buried reservoir Below grade Requires pumping; subject to the 22 CCR 64585 subsurface requirements including 50-foot separation from sanitary sewers and groundwater monitoring

Hydropneumatic (pressure) tank At grade Small systems; air cushion maintains pressure between pump cycles; very little usable storage

Level and Pressure Pressure at the base (psi) = Water depth (ft) × 0.433 \text{Pressure at the base (psi)} = \text{Water depth (ft)} \times 0.433 Pressure at the base (psi) = Water depth (ft) × 0.433 Pressure at a service (psi) = ( Tank water surface elevation − Service elevation ) × 0.433 \text{Pressure at a service (psi)} = (\text{Tank water surface elevation} - \text{Service elevation}) \times 0.433 Pressure at a service (psi) = ( Tank water surface elevation − Service elevation ) × 0.433

Example: a hilltop tank with an overflow elevation of 640 ft, currently 8 ft below overflow, serving a home at elevation 465 ft.

Water surface = 640 - 8 = 632 ft. Difference = 632 - 465 = 167 ft.

Static pressure = 167 x 0.433 = 72.3 psi

A tank that floats on the system is a pressure-setting device. Every foot the level drops removes 0.433 psi from every customer in the zone. That is why level, not volume, is the operational control variable.

Control Valves

Altitude valve - closes to prevent overflow when the tank reaches a set level; a two-way altitude valve also allows the tank to feed back into the system on demand.

Level transmitters - pressure transducer, ultrasonic, radar, or float; feed SCADA and the pump control logic.

Overflow - must terminate with a screened, downturned outlet and a proper air gap , and may never be directly connected to a sewer or storm drain .

Drain and washout - sized to empty the tank for inspection, also air-gapped.

Turnover: The Water Quality Problem

Storage is the place in a distribution system with the longest detention time , and long detention causes four predictable problems:

Loss of disinfectant residual - decay is continuous and accelerates with temperature

Disinfection byproduct formation - free chlorine plus organic precursors plus time equals TTHM and HAA5, and Stage 2 evaluates each monitoring site on its own LRAA

Nitrification in chloraminated systems - the warm, low-residual, low-velocity interior of a tank is the ideal nitrifier habitat

Thermal stratification - a tall tank in summer develops a warm surface layer that never mixes with the cold bottom, so a nominally "turned over" tank may be exchanging only the top few feet

Managing Turnover

Cycle through a wider level band. A tank operated between 90 and 95 percent full exchanges 5 percent of its volume per cycle. Widening the band to 70-95 percent exchanges five times as much.

Separate inlet and outlet , arranged to minimize short-circuiting - a design requirement for new reservoirs under 22 CCR 64585. Where a common inlet/outlet pipe exists, the incoming water tends to leave immediately and a large volume never exchanges.

Active mixing systems - submersible mixers or nozzle systems that break stratification.

Seasonal deep cycling - deliberately drawing a problem tank far down during low-demand periods, with residual and turbidity monitoring during recovery.

Booster disinfection at the tank outlet where residual cannot be maintained by turnover alone.

Right-size the storage. Storage sized for a growth projection that never happened is a permanent water quality liability.

Tip

Water age is not the same as detention time. A tank with a 3-day theoretical detention time and a common inlet/outlet may have a well-mixed 20 percent and an 80 percent that is weeks old. Tracer studies, temperature profiling at multiple depths, and residual profiles at multiple depths are how operators find out which one they have.

Inspection and Maintenance

Item Frequency What to look for

Vents and screens Routine (monthly to quarterly) Corrosion-resistant screen intact, typically 24-mesh; no gaps, no bird or insect entry

  • Hatches Routine Gasketed, overlapping, locked , raised curb with a downturned lip
  • Overflow Routine Screened, downturned, flap or duckbill intact, air gap present, no sewer connection
  • Exterior coating and cathodic protection Annual Rust, blistering, anode condition

Interior inspection Every 3-5 years typically Coating failure, sediment depth, corrosion, structural condition - by diver or ROV, or after draining

Level instrumentation Routine Verify against a physical measurement; a failed level transmitter can overflow a tank or run a zone dry

Security Routine Fencing, locks, intrusion alarms, ladder guards

Any reservoir taken out of service for repair or inspection must be disinfected and sampled under AWWA C652-02 before return to service, and if coliform is detected the reservoir must be resampled with results submitted to the State Board for review and approval.