Study guide

11.4 Stage 1 & Stage 2 Disinfection Byproduct Rules

California Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: California Water Regulatory Framework & Certification Ladders

1.1 State Water Board & Regional Boards Structure 1.2 Drinking Water Certification: T1-T5 & D1-D5 Requirements 1.3 Wastewater Certification: Grades I-V & OIT Requirements 1.4 Safe Drinking Water Standards, MCLs & Emerging Contaminants 1.5 California Waterworks Standards (Title 22, Chapter 16) 1.6 Public Water System Types, Permits & the Sanitary Survey

2 Chapter 2: California Water Rights, Title 22 & Environmental Policy

2.1 California Title 22 Recycled Water Standards 2.2 California Environmental Quality Act (CEQA) & Proposition 218 2.3 Water Rights & California Water Resources

3 Chapter 3: Drinking Water Source Quality & Coagulation/Flocculation

3.1 Source Water Quality & Watershed Management 3.2 Coagulation Chemistry & Flash Mixing 3.3 Flocculation & Jar Testing 3.4 Wells, Aquifers & Groundwater Hydraulics 3.5 Raw Water Storage, Clearwells & Reservoir Management

4 Chapter 4: Clarification & Granular Media Filtration

4.1 Sedimentation & Advanced Clarification 4.2 Granular Media Filtration Mechanics & Media Types 4.3 Filter Operation, Backwash Cycles & SWTR Compliance

5 Chapter 5: Disinfection, Oxidation & Advanced Water Treatment

5.1 Chlorination Chemistry & Breakpoint Curves 5.2 Disinfection Kinetics & CT Calculations 5.3 Alternative Disinfection: Ozone, UV & Chlorine Dioxide 5.4 Advanced Treatment: Membranes, AOP & PFAS Adsorption 5.5 Chloramination & Nitrification Control 5.6 Iron & Manganese Removal 5.7 Fluoridation Practice & Compliance 5.8 Corrosion Control Treatment & Water Stability 5.9 Taste & Odor Control and Algal Toxin Management

6 Chapter 6: Wastewater Preliminary & Primary Treatment

6.1 Preliminary Treatment: Screening & Grit Removal 6.2 Primary Clarification Operations 6.3 Primary Sludge Characteristics & Pumping 6.4 Stabilization Ponds, Lagoons & Small-Plant Processes

7 Chapter 7: Secondary Biological Treatment & Activated Sludge

7.1 Activated Sludge Process Fundamentals 7.2 Process Control Parameters: F/M, MCRT & SVI 7.3 Activated Sludge Microbiology & Troubleshooting 7.4 Fixed-Film & Hybrid Biological Processes

8 Chapter 8: Biological Nutrient Removal, Water Reuse & Solids Handling

8.1 Biological Nitrogen Removal: Nitrification & Denitrification 8.2 Biological Phosphorus Removal (EBPR) & Chemical Precipitation 8.3 Anaerobic & Aerobic Digestion 8.4 Sludge Thickening, Dewatering & Biosolids Disposal 8.5 Wastewater Disinfection: Chlorination, Dechlorination & UV

9 Chapter 9: Distribution Systems, Collection Networks & Hydraulics

9.1 Hydraulics, Pressure & Flow Dynamics 9.2 Centrifugal Pumps, Motors & VFDs 9.3 Distribution Network Infrastructure & Cross-Connection Control 9.4 Wastewater Collection Systems, SSMP & FOG Management

10 Chapter 10: Laboratory Analytics, Safety & Water Math

10.1 Water & Wastewater Laboratory Methods 10.2 Laboratory Quality Assurance & Regulatory Reporting 10.3 Chemical Safety, Hazardous Gases & Confined Space 10.4 Essential Water & Wastewater Math for Operators

11 Chapter 11: Federal & California Drinking Water Rules

11.1 The Revised Total Coliform Rule & Assessments 11.2 The Lead and Copper Rule and Service Line Replacement 11.3 Surface Water Treatment Rules & Log Removal Credit 11.4 Stage 1 & Stage 2 Disinfection Byproduct Rules 11.5 Secondary MCLs, Notification Levels & Response Levels 11.6 Public Notification, Consumer Confidence Reports & Recordkeeping

12 Chapter 12: Distribution System Design, Demand & Hydraulics

12.1 System Layout, Pressure Zones & Distribution Maps 12.2 Water Demand, Peaking Factors & Fire Flow 12.3 Distribution Storage: Types, Sizing & Turnover 12.4 Head Loss, C-Factor & Distribution Hydraulic Calculations 12.5 Water Hammer, Surge Control & Air Management

13 Chapter 13: Distribution Equipment Operation, Maintenance & Inspection

13.1 Valves: Types, Operation & Exercising Programs 13.2 Fire Hydrants: Types, Testing & Maintenance 13.3 Water Meters: Types, Accuracy & Meter Management 13.4 Instrumentation, In-Line Sensors, Telemetry & SCADA 13.5 Electrical Systems, Motors & Standby Generators 13.6 External Corrosion, Cathodic Protection & Asset Inspection

14 Chapter 14: Water Mains, Piping & Field Construction

14.1 Pipe Materials & Pipe Selection 14.2 Joints, Fittings, Thrust Restraint & Bedding 14.3 Main Installation, Tapping & Service Line Installation 14.4 Leak Detection, Water Loss Auditing & Main Repair 14.5 Main Cleaning & Maintenance: Flushing, Pigging & Lining 14.6 Excavation, Trench Safety & Utility Locating

15 Chapter 15: Disinfecting Distribution Facilities & Maintaining Water Quality

15.1 Water Main Disinfection (AWWA C651) 15.2 Disinfecting Storage Reservoirs (C652) & Wells (C654) 15.3 Maintaining Distribution Water Quality: Residual, Biofilm & Discolored Water 15.4 Cross-Connection Control Program Administration & Device Testing

16 Chapter 16: Plant Equipment, Chemical Feed & Maintenance

16.1 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 16.2 Gas Chlorination Equipment & Hypochlorite Systems 16.3 Blowers, Compressors & Aeration Equipment 16.4 Flow Measurement Devices: Meters, Weirs & Flumes 16.5 Preventive Maintenance, CMMS & Asset Management

17 Chapter 17: Utility Management, Administration & Emergency Response

17.1 Planning, Organizing, Directing & Controlling a Utility Work Group 17.2 Budgets, Water Rates & Financial Management 17.3 Operator Training, Staffing & Safety Program Development 17.4 Energy Management & Optimization 17.5 Emergency Response Planning, Risk & Resilience & Security 17.6 Water Conservation Planning & Drought Response

18 Chapter 18: Applied Operator Mathematics Workshop

18.1 The Exam Conversion Sheet, Units & Dimensional Analysis 18.2 Distribution & Hydraulic Math Workshop 18.3 Treatment & Wastewater Process Math Workshop

11.4 Stage 1 & Stage 2 Disinfection Byproduct Rules

Key Takeaways Explain This Topic AI

The Disinfection By-Product Rule is a named sub-topic in the SWRCB distribution Expected Range of Knowledge, and Disinfectant By-Products is separately named under Disinfection.

Stage 1 sets MCLs of 0.080 mg/L for total trihalomethanes, 0.060 mg/L for the five haloacetic acids, 0.010 mg/L for bromate, and 1.0 mg/L for chlorite.

Maximum residual disinfectant levels are 4.0 mg/L for chlorine and chloramines as an annual average and 0.8 mg/L for chlorine dioxide.

Stage 2 changed compliance from a system-wide running annual average to a locational running annual average calculated separately at each monitoring site.

Byproduct formation increases with higher total organic carbon, higher chlorine dose, longer contact time, higher temperature, and higher pH for trihalomethanes.

Last updated: September 2026

The Fundamental Trade-Off

Chlorine reacts with natural organic matter (NOM) - humic and fulvic acids from decaying vegetation - to form halogenated byproducts. Where bromide is present in the source, brominated species form as well, and California's coastal and Delta-influenced sources carry significant bromide. The regulatory answer has never been to stop disinfecting; it is to remove the precursors, minimize the dose and the contact time, and use disinfectants that form fewer byproducts.

The Regulated Families

Group Members MCL

Total trihalomethanes (TTHM) Chloroform, bromodichloromethane, dibromochloromethane, bromoform 0.080 mg/L (80 µg/L)

Haloacetic acids (HAA5) Monochloroacetic, dichloroacetic, trichloroacetic, monobromoacetic, dibromoacetic 0.060 mg/L (60 µg/L)

  • Bromate (from ozone + bromide) - 0.010 mg/L
  • Chlorite (from chlorine dioxide ) - 1.0 mg/L
  • Maximum Residual Disinfectant Levels (MRDLs)

MRDLs limit the disinfectant itself, not its byproducts:

  • Disinfectant MRDL Basis
  • Chlorine 4.0 mg/L as Cl₂ Running annual average
  • Chloramines 4.0 mg/L as Cl₂ Running annual average
  • Chlorine dioxide 0.8 mg/L Daily, at the entrance to the distribution system

Note

MRDLG vs MRDL vs MCLG vs MCL. The maximum residual disinfectant level goal (MRDLG) and the maximum contaminant level goal (MCLG) are non-enforceable health targets. The MRDL and MCL are the enforceable numbers. Chlorine dioxide is the odd one out - it is measured daily at the entry point rather than as an annual average, because its acute health endpoint differs.

Stage 1 (1998/2002)

Stage 1 established the MCLs and MRDLs above and added precursor removal requirements. Compliance was based on a running annual average (RAA) of all samples system-wide - which meant a system could average away a chronically high site with several low ones.

Enhanced Coagulation and Enhanced Softening

Conventional filtration plants must remove a specified percentage of total organic carbon (TOC) between the source and the combined filter effluent, based on a matrix of source TOC and source alkalinity :

  • Source TOC (mg/L) Source alkalinity 0-60 mg/L 60-120 mg/L > 120 mg/L
  • > 2.0 to 4.0 35.0% 25.0% 15.0%
  • > 4.0 to 8.0 45.0% 35.0% 25.0%
  • > 8.0 50.0% 40.0% 30.0%

The pattern is intuitive once you see it: higher TOC means more removal required; higher alkalinity means less removal required , because high-alkalinity water resists the pH depression that makes enhanced coagulation work. Plants with source TOC of 2.0 mg/L or less are not subject to the requirement.

Systems can also comply through alternative compliance criteria , such as source TOC below 2.0 mg/L, treated TOC below 2.0 mg/L, low SUVA, or already-low TTHM and HAA5 levels.

Enhanced coagulation in practice means increasing coagulant dose and depressing pH into roughly the 5.5 to 6.5 range, where metal-humate complexation and adsorption onto the metal hydroxide floc are strongest. The costs are real: more coagulant, more sludge, more caustic downstream to bring pH back up for corrosion control, and potential effects on filter performance.

Stage 2 (2006) - The Change That Mattered

Stage 2 kept the same MCLs but changed where and how compliance is calculated :

Stage 1 Stage 2

Compliance metric Running annual average (RAA) of all sites combined Locational running annual average (LRAA) - each site averaged separately

Site selection Representative sites Sites selected from an Initial Distribution System Evaluation (IDSE) targeting high TTHM and high HAA5 locations

Effect High sites could be offset by low sites Every site must comply on its own LRAA site = Q 1 + Q 2 + Q 3 + Q 4 at that site 4 \text{LRAA}_{\text{site}} = \frac{Q_1 + Q_2 + Q_3 + Q_4 \text{ at that site}}{4} LRAA site ​ = 4 Q 1 ​ + Q 2 ​ + Q 3 ​ + Q 4 ​ at that site ​

Worked example. A monitoring site returns quarterly TTHM results of 62, 78, 104, and 88 µg/L.

LRAA = (62 + 78 + 104 + 88) / 4 = 332 / 4 = 83 µg/L - which exceeds the 80 µg/L MCL at that location, and it is a violation even if every other site in the system averages 40 µg/L.

Important

Stage 2 is why distribution system water age became an operational priority. Under Stage 1, a system could tolerate a stagnant tank at the end of a long transmission main. Under Stage 2, that tank's monitoring site has to comply by itself, and TTHM keeps forming as long as free chlorine and organic precursors are in contact. Reducing water age is a DBP control strategy.

Stage 2 also added the operational evaluation level (OEL) : if the sum of the two previous quarters plus twice the current quarter, divided by four, exceeds the MCL at any site, the system must conduct an operational evaluation and submit it - an early warning that fires before the LRAA itself goes over.

Operational Control Levers

Lever Mechanism Trade-off

Remove precursors - enhanced coagulation, GAC, membranes Less NOM to react with Chemical cost, sludge, pH management

Move the point of chlorination downstream (post-filter rather than pre-coagulant) Chlorine contacts far less NOM Lose pre-oxidation benefits and some CT

Convert to chloramines for the distribution residual Chloramine forms far less TTHM/HAA5 Nitrification risk ; weaker disinfectant; dialysis and aquatic notifications

Lower the chlorine dose to the minimum that meets CT Less reactant Must not compromise inactivation or residual

Reduce water age - tank turnover, unidirectional flushing, looping dead ends Less contact time Water loss during flushing

Aeration of finished water Strips volatile THMs Does not remove HAA5 , which are non-volatile

Use ozone or UV for primary disinfection Little or no halogenated byproduct Ozone forms bromate with bromide present; UV gives no residual

Tip

THMs and HAA5 respond differently, and that is heavily tested. THMs are volatile and rise with higher pH ; HAA5 are non-volatile and form better at lower pH . Aeration and spray systems strip THMs but do nothing for HAA5. HAA5 are also biodegradable in the distribution system, so HAA5 can actually decline with water age while TTHM climbs. If a system is failing HAA5 near the plant and TTHM at the far end, that pattern is chemistry, not a sampling error.