Study guide

16.1 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration

California Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: California Water Regulatory Framework & Certification Ladders

1.1 State Water Board & Regional Boards Structure 1.2 Drinking Water Certification: T1-T5 & D1-D5 Requirements 1.3 Wastewater Certification: Grades I-V & OIT Requirements 1.4 Safe Drinking Water Standards, MCLs & Emerging Contaminants 1.5 California Waterworks Standards (Title 22, Chapter 16) 1.6 Public Water System Types, Permits & the Sanitary Survey

2 Chapter 2: California Water Rights, Title 22 & Environmental Policy

2.1 California Title 22 Recycled Water Standards 2.2 California Environmental Quality Act (CEQA) & Proposition 218 2.3 Water Rights & California Water Resources

3 Chapter 3: Drinking Water Source Quality & Coagulation/Flocculation

3.1 Source Water Quality & Watershed Management 3.2 Coagulation Chemistry & Flash Mixing 3.3 Flocculation & Jar Testing 3.4 Wells, Aquifers & Groundwater Hydraulics 3.5 Raw Water Storage, Clearwells & Reservoir Management

4 Chapter 4: Clarification & Granular Media Filtration

4.1 Sedimentation & Advanced Clarification 4.2 Granular Media Filtration Mechanics & Media Types 4.3 Filter Operation, Backwash Cycles & SWTR Compliance

5 Chapter 5: Disinfection, Oxidation & Advanced Water Treatment

5.1 Chlorination Chemistry & Breakpoint Curves 5.2 Disinfection Kinetics & CT Calculations 5.3 Alternative Disinfection: Ozone, UV & Chlorine Dioxide 5.4 Advanced Treatment: Membranes, AOP & PFAS Adsorption 5.5 Chloramination & Nitrification Control 5.6 Iron & Manganese Removal 5.7 Fluoridation Practice & Compliance 5.8 Corrosion Control Treatment & Water Stability 5.9 Taste & Odor Control and Algal Toxin Management

6 Chapter 6: Wastewater Preliminary & Primary Treatment

6.1 Preliminary Treatment: Screening & Grit Removal 6.2 Primary Clarification Operations 6.3 Primary Sludge Characteristics & Pumping 6.4 Stabilization Ponds, Lagoons & Small-Plant Processes

7 Chapter 7: Secondary Biological Treatment & Activated Sludge

7.1 Activated Sludge Process Fundamentals 7.2 Process Control Parameters: F/M, MCRT & SVI 7.3 Activated Sludge Microbiology & Troubleshooting 7.4 Fixed-Film & Hybrid Biological Processes

8 Chapter 8: Biological Nutrient Removal, Water Reuse & Solids Handling

8.1 Biological Nitrogen Removal: Nitrification & Denitrification 8.2 Biological Phosphorus Removal (EBPR) & Chemical Precipitation 8.3 Anaerobic & Aerobic Digestion 8.4 Sludge Thickening, Dewatering & Biosolids Disposal 8.5 Wastewater Disinfection: Chlorination, Dechlorination & UV

9 Chapter 9: Distribution Systems, Collection Networks & Hydraulics

9.1 Hydraulics, Pressure & Flow Dynamics 9.2 Centrifugal Pumps, Motors & VFDs 9.3 Distribution Network Infrastructure & Cross-Connection Control 9.4 Wastewater Collection Systems, SSMP & FOG Management

10 Chapter 10: Laboratory Analytics, Safety & Water Math

10.1 Water & Wastewater Laboratory Methods 10.2 Laboratory Quality Assurance & Regulatory Reporting 10.3 Chemical Safety, Hazardous Gases & Confined Space 10.4 Essential Water & Wastewater Math for Operators

11 Chapter 11: Federal & California Drinking Water Rules

11.1 The Revised Total Coliform Rule & Assessments 11.2 The Lead and Copper Rule and Service Line Replacement 11.3 Surface Water Treatment Rules & Log Removal Credit 11.4 Stage 1 & Stage 2 Disinfection Byproduct Rules 11.5 Secondary MCLs, Notification Levels & Response Levels 11.6 Public Notification, Consumer Confidence Reports & Recordkeeping

12 Chapter 12: Distribution System Design, Demand & Hydraulics

12.1 System Layout, Pressure Zones & Distribution Maps 12.2 Water Demand, Peaking Factors & Fire Flow 12.3 Distribution Storage: Types, Sizing & Turnover 12.4 Head Loss, C-Factor & Distribution Hydraulic Calculations 12.5 Water Hammer, Surge Control & Air Management

13 Chapter 13: Distribution Equipment Operation, Maintenance & Inspection

13.1 Valves: Types, Operation & Exercising Programs 13.2 Fire Hydrants: Types, Testing & Maintenance 13.3 Water Meters: Types, Accuracy & Meter Management 13.4 Instrumentation, In-Line Sensors, Telemetry & SCADA 13.5 Electrical Systems, Motors & Standby Generators 13.6 External Corrosion, Cathodic Protection & Asset Inspection

14 Chapter 14: Water Mains, Piping & Field Construction

14.1 Pipe Materials & Pipe Selection 14.2 Joints, Fittings, Thrust Restraint & Bedding 14.3 Main Installation, Tapping & Service Line Installation 14.4 Leak Detection, Water Loss Auditing & Main Repair 14.5 Main Cleaning & Maintenance: Flushing, Pigging & Lining 14.6 Excavation, Trench Safety & Utility Locating

15 Chapter 15: Disinfecting Distribution Facilities & Maintaining Water Quality

15.1 Water Main Disinfection (AWWA C651) 15.2 Disinfecting Storage Reservoirs (C652) & Wells (C654) 15.3 Maintaining Distribution Water Quality: Residual, Biofilm & Discolored Water 15.4 Cross-Connection Control Program Administration & Device Testing

16 Chapter 16: Plant Equipment, Chemical Feed & Maintenance

16.1 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 16.2 Gas Chlorination Equipment & Hypochlorite Systems 16.3 Blowers, Compressors & Aeration Equipment 16.4 Flow Measurement Devices: Meters, Weirs & Flumes 16.5 Preventive Maintenance, CMMS & Asset Management

17 Chapter 17: Utility Management, Administration & Emergency Response

17.1 Planning, Organizing, Directing & Controlling a Utility Work Group 17.2 Budgets, Water Rates & Financial Management 17.3 Operator Training, Staffing & Safety Program Development 17.4 Energy Management & Optimization 17.5 Emergency Response Planning, Risk & Resilience & Security 17.6 Water Conservation Planning & Drought Response

18 Chapter 18: Applied Operator Mathematics Workshop

18.1 The Exam Conversion Sheet, Units & Dimensional Analysis 18.2 Distribution & Hydraulic Math Workshop 18.3 Treatment & Wastewater Process Math Workshop

16.1 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration

Key Takeaways Explain This Topic AI

Chemical Feeders is a named sub-topic in both the treatment Operation/Maintenance category and the distribution Equipment category.

Solution feeders meter a liquid at a set rate, while dry feeders are volumetric, metering by volume, or gravimetric, metering by weight.

Gravimetric feeders are more accurate than volumetric feeders because they compensate for changes in bulk density and moisture.

Drawdown calibration measures the actual volume delivered over a timed interval and is the only reliable check of a feeder's true output.

Every chemical feed system must be interlocked to plant flow so that loss of flow stops the feed, and every direct additive must be certified to NSF/ANSI/CAN 61.

Last updated: September 2026

  • Feed Equipment
  • Solution (Liquid) Feeders

Type Description Notes

Diaphragm metering pump A reciprocating diaphragm displaces a fixed volume per stroke; rate set by stroke length and stroke frequency The workhorse; pulsating flow requires a pulsation dampener for smooth feed

Piston/plunger metering pump Positive displacement with a piston Higher pressure capability; more wear surfaces in contact with chemical

Peristaltic (hose) pump Rollers squeeze a flexible tube Chemical contacts only the tube ; excellent for slurries, lime, and polymer; tube is a wear item

Progressive cavity pump Rotor turning in a stator Viscous chemicals, polymer, sludge

Gravity feed with a rotameter and valve Simple metering from an elevated tank Small systems; sensitive to head changes

Eductor / hydraulic feeder Venturi draws solution into the flow stream Used with gas chlorinators and some liquid systems

Essential accessories on any solution feed: a calibration cylinder (drawdown tube) , a back-pressure valve to give the pump something to work against, a pressure relief valve to protect the pump and piping, an anti-siphon valve to prevent the feed line siphoning the whole day tank into the main, a degassing head or foot valve where the chemical off-gasses (sodium hypochlorite does), a strainer , and an injection quill placed in a turbulent, well-mixed location.

Dry Feeders

Type Principle Accuracy

Volumetric - screw, belt, rotary vane, oscillating hopper Meters a volume per unit time ±2 to 5 percent, and it drifts with bulk density, moisture, and particle size

Gravimetric - belt with a weigh bridge, or loss-in-weight hopper Meters a weight per unit time ±1 percent or better ; self-correcting for density changes

Dry chemicals almost always feed into a dissolving or slurry chamber with a controlled water supply and a mixer, then to the point of application. Dry systems fail predictably from bridging or arching in the hopper (solved by a bin vibrator or agitator), flooding (fine material flowing uncontrolled), hygroscopic caking (solved by a dehumidified room or hopper heaters), and plugged slurry lines (solved by adequate velocity, flushing connections, and, for lime, regular acid cleaning).

Tip

Gravimetric feeders exist because bulk density lies. A volumetric feeder set to deliver 40 lb/hour of soda ash delivers whatever weight happens to be in that volume. If a new shipment is finer, damper, or more compacted, the actual weight changes and the dose changes with it, silently. A gravimetric feeder measures weight directly and corrects itself.

Feed Pacing and Control

  • Control mode How it works Use
  • Manual Fixed rate set by the operator Only for steady flow and steady water quality

Flow-paced (feed-forward) Feed rate proportional to a 4-20 mA plant flow signal The baseline for nearly every chemical

Residual/analyzer-paced (feedback) Feed trimmed by a measured result - chlorine residual, pH, fluoride, streaming current Corrects for demand changes

Compound loop Flow pacing with analyzer trim The standard for chlorine and pH control ; fast response plus accuracy

Warning

Every chemical feeder must be interlocked to plant flow. If the plant stops and the feeder does not, the chemical accumulates in a static line and is then delivered as a slug when flow resumes. Nearly every documented drinking water chemical overfeed - fluoride, caustic, chlorine - traces to a feeder that kept running into a stopped or greatly reduced flow. Interlocks should be hard-wired, tested on a schedule, and never bypassed for convenience.

Calibration by Drawdown

A feeder's dial setting is a claim; a drawdown test is a measurement.

Procedure: isolate the day tank and align the pump suction to a calibration cylinder of known graduation. Run the pump at the setting to be verified for a timed interval. Record the volume drawn down. Return the suction to the day tank. Feed rate (gal/day) = Volume drawn (mL) Time (min) × 1,440 3,785 \text{Feed rate (gal/day)} = \frac{\text{Volume drawn (mL)}}{\text{Time (min)}} \times \frac{1{,}440}{3{,}785} Feed rate (gal/day) = Time (min) Volume drawn (mL) ​ × 3 , 785 1 , 440 ​

Worked example. A hypochlorite pump draws 420 mL in 5 minutes .

  • Rate = 420 / 5 = 84 mL/min
  • = 84 x 1,440 = 120,960 mL/day = 31.96 gal/day

Now check the dose. The plant is treating 2.2 MGD with 12.5 percent sodium hypochlorite weighing 10.0 lb/gal :

Pounds of chlorine delivered = 31.96 x 10.0 x 0.125 = 39.95 lb/day Dose = 39.95 / (2.2 x 8.34) = 39.95 / 18.35 = 2.18 mg/L

If the target dose was 2.5 mg/L, the pump setting must be increased by a factor of 2.5 / 2.18 = 1.15 , and the drawdown repeated to confirm.

Dry feeder calibration uses the same logic with a catch and weigh : divert the discharge into a container for a timed interval, weigh it, and compute pounds per hour or per day.

Calibrate on installation, after any repair or setting change, after a chemical strength or supplier change, and on a routine schedule - monthly is common for critical feeds.

Solution Strength Calculations

Two forms recur constantly.

Percent solution: % = lb of chemical lb of solution × 100 \% = \frac{\text{lb of chemical}}{\text{lb of solution}} \times 100 % = lb of solution lb of chemical ​ × 100

Example: 60 lb of soda ash in 480 lb of water gives 60 / 540 x 100 = 11.1 percent .

Dilution (mixing) equation: C 1 V 1 = C 2 V 2 C_1 V_1 = C_2 V_2 C 1 ​ V 1 ​ = C 2 ​ V 2 ​

Example: how much 12.5 percent hypochlorite is needed to make 60 gallons of 2.0 percent solution?

V₁ = (2.0 x 60) / 12.5 = 9.6 gallons of hypochlorite, diluted to 60 gallons total.

Available chlorine and purity must be applied wherever the chemical is not pure: lb/day of product = Flow (MGD) × Dose (mg/L) × 8.34 Purity or available fraction \text{lb/day of product} = \frac{\text{Flow (MGD)} \times \text{Dose (mg/L)} \times 8.34}{\text{Purity or available fraction}} lb/day of product = Purity or available fraction Flow (MGD) × Dose (mg/L) × 8.34 ​

Example: 3.0 MGD dosed at 2.4 mg/L with 65 percent calcium hypochlorite:

  • Chlorine needed = 3.0 x 2.4 x 8.34 = 60.0 lb/day
  • Product = 60.0 / 0.65 = 92.3 lb/day
  • Common Feed Problems

Symptom Cause

Pump runs but no flow Vapor lock / gas binding from hypochlorite off-gassing; lost prime; plugged foot valve or strainer; failed check valves

Feed rate drifts down over days Hypochlorite degradation (loses strength with heat, light, and time), scale on the injection quill, worn check valves

Erratic dose Pulsation without a dampener, air in the suction line, fluctuating back pressure

Feed line plugs Calcium carbonate scale where hypochlorite meets hard water at the injection point; lime scale; polymer gelling

Dose too low despite correct setting Chemical is weaker than assumed - verify strength; volumetric dry feeder density change

Slug dose after a shutdown Feeder not interlocked to flow

White crust around the injection point Scale - use a soft water dilution stream or acid-clean the quill on a schedule

Important

Sodium hypochlorite degrades. Strength falls with temperature, light exposure, storage time, and the presence of metal ions, and the degradation also produces chlorate . Store it cool, dark, and no longer than about 30 to 60 days, rotate stock, and verify strength on receipt and periodically thereafter rather than assuming the label. A 12.5 percent product that has aged to 9 percent delivers 28 percent less chlorine at the same pump setting.

Chemical Safety and Certification

NSF/ANSI/CAN Standard 60 certification is required for every direct additive - coagulant, disinfectant, fluoride, caustic, polymer, corrosion inhibitor. NSF/ANSI/CAN 61 covers indirect additives, the materials that contact water: pipe, linings, coatings, gaskets, valves.

Never mix incompatible chemicals. Sodium hypochlorite plus an acid releases chlorine gas ; hypochlorite plus ammonia releases chloramine vapor . Separate storage, separate containment, separate and clearly labeled fill connections , and unique fill fitting types so a delivery driver physically cannot connect to the wrong tank.

Secondary containment sized for the largest tank plus freeboard, with no floor drain that would carry a spill offsite.

Eyewash and safety shower within 10 seconds' travel of any corrosive chemical area, tested weekly.

Compatible materials throughout - PVC, CPVC, PVDF, PTFE, and specific elastomers depending on the chemical. Sodium hypochlorite attacks many metals; caustic attacks aluminum; acids attack concrete.

Safety data sheets accessible, current, and known to the crew; labeling at every tank, pump, and line.