Study guide

3.4 Wells, Aquifers & Groundwater Hydraulics

California Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: California Water Regulatory Framework & Certification Ladders

1.1 State Water Board & Regional Boards Structure 1.2 Drinking Water Certification: T1-T5 & D1-D5 Requirements 1.3 Wastewater Certification: Grades I-V & OIT Requirements 1.4 Safe Drinking Water Standards, MCLs & Emerging Contaminants 1.5 California Waterworks Standards (Title 22, Chapter 16) 1.6 Public Water System Types, Permits & the Sanitary Survey

2 Chapter 2: California Water Rights, Title 22 & Environmental Policy

2.1 California Title 22 Recycled Water Standards 2.2 California Environmental Quality Act (CEQA) & Proposition 218 2.3 Water Rights & California Water Resources

3 Chapter 3: Drinking Water Source Quality & Coagulation/Flocculation

3.1 Source Water Quality & Watershed Management 3.2 Coagulation Chemistry & Flash Mixing 3.3 Flocculation & Jar Testing 3.4 Wells, Aquifers & Groundwater Hydraulics 3.5 Raw Water Storage, Clearwells & Reservoir Management

4 Chapter 4: Clarification & Granular Media Filtration

4.1 Sedimentation & Advanced Clarification 4.2 Granular Media Filtration Mechanics & Media Types 4.3 Filter Operation, Backwash Cycles & SWTR Compliance

5 Chapter 5: Disinfection, Oxidation & Advanced Water Treatment

5.1 Chlorination Chemistry & Breakpoint Curves 5.2 Disinfection Kinetics & CT Calculations 5.3 Alternative Disinfection: Ozone, UV & Chlorine Dioxide 5.4 Advanced Treatment: Membranes, AOP & PFAS Adsorption 5.5 Chloramination & Nitrification Control 5.6 Iron & Manganese Removal 5.7 Fluoridation Practice & Compliance 5.8 Corrosion Control Treatment & Water Stability 5.9 Taste & Odor Control and Algal Toxin Management

6 Chapter 6: Wastewater Preliminary & Primary Treatment

6.1 Preliminary Treatment: Screening & Grit Removal 6.2 Primary Clarification Operations 6.3 Primary Sludge Characteristics & Pumping 6.4 Stabilization Ponds, Lagoons & Small-Plant Processes

7 Chapter 7: Secondary Biological Treatment & Activated Sludge

7.1 Activated Sludge Process Fundamentals 7.2 Process Control Parameters: F/M, MCRT & SVI 7.3 Activated Sludge Microbiology & Troubleshooting 7.4 Fixed-Film & Hybrid Biological Processes

8 Chapter 8: Biological Nutrient Removal, Water Reuse & Solids Handling

8.1 Biological Nitrogen Removal: Nitrification & Denitrification 8.2 Biological Phosphorus Removal (EBPR) & Chemical Precipitation 8.3 Anaerobic & Aerobic Digestion 8.4 Sludge Thickening, Dewatering & Biosolids Disposal 8.5 Wastewater Disinfection: Chlorination, Dechlorination & UV

9 Chapter 9: Distribution Systems, Collection Networks & Hydraulics

9.1 Hydraulics, Pressure & Flow Dynamics 9.2 Centrifugal Pumps, Motors & VFDs 9.3 Distribution Network Infrastructure & Cross-Connection Control 9.4 Wastewater Collection Systems, SSMP & FOG Management

10 Chapter 10: Laboratory Analytics, Safety & Water Math

10.1 Water & Wastewater Laboratory Methods 10.2 Laboratory Quality Assurance & Regulatory Reporting 10.3 Chemical Safety, Hazardous Gases & Confined Space 10.4 Essential Water & Wastewater Math for Operators

11 Chapter 11: Federal & California Drinking Water Rules

11.1 The Revised Total Coliform Rule & Assessments 11.2 The Lead and Copper Rule and Service Line Replacement 11.3 Surface Water Treatment Rules & Log Removal Credit 11.4 Stage 1 & Stage 2 Disinfection Byproduct Rules 11.5 Secondary MCLs, Notification Levels & Response Levels 11.6 Public Notification, Consumer Confidence Reports & Recordkeeping

12 Chapter 12: Distribution System Design, Demand & Hydraulics

12.1 System Layout, Pressure Zones & Distribution Maps 12.2 Water Demand, Peaking Factors & Fire Flow 12.3 Distribution Storage: Types, Sizing & Turnover 12.4 Head Loss, C-Factor & Distribution Hydraulic Calculations 12.5 Water Hammer, Surge Control & Air Management

13 Chapter 13: Distribution Equipment Operation, Maintenance & Inspection

13.1 Valves: Types, Operation & Exercising Programs 13.2 Fire Hydrants: Types, Testing & Maintenance 13.3 Water Meters: Types, Accuracy & Meter Management 13.4 Instrumentation, In-Line Sensors, Telemetry & SCADA 13.5 Electrical Systems, Motors & Standby Generators 13.6 External Corrosion, Cathodic Protection & Asset Inspection

14 Chapter 14: Water Mains, Piping & Field Construction

14.1 Pipe Materials & Pipe Selection 14.2 Joints, Fittings, Thrust Restraint & Bedding 14.3 Main Installation, Tapping & Service Line Installation 14.4 Leak Detection, Water Loss Auditing & Main Repair 14.5 Main Cleaning & Maintenance: Flushing, Pigging & Lining 14.6 Excavation, Trench Safety & Utility Locating

15 Chapter 15: Disinfecting Distribution Facilities & Maintaining Water Quality

15.1 Water Main Disinfection (AWWA C651) 15.2 Disinfecting Storage Reservoirs (C652) & Wells (C654) 15.3 Maintaining Distribution Water Quality: Residual, Biofilm & Discolored Water 15.4 Cross-Connection Control Program Administration & Device Testing

16 Chapter 16: Plant Equipment, Chemical Feed & Maintenance

16.1 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 16.2 Gas Chlorination Equipment & Hypochlorite Systems 16.3 Blowers, Compressors & Aeration Equipment 16.4 Flow Measurement Devices: Meters, Weirs & Flumes 16.5 Preventive Maintenance, CMMS & Asset Management

17 Chapter 17: Utility Management, Administration & Emergency Response

17.1 Planning, Organizing, Directing & Controlling a Utility Work Group 17.2 Budgets, Water Rates & Financial Management 17.3 Operator Training, Staffing & Safety Program Development 17.4 Energy Management & Optimization 17.5 Emergency Response Planning, Risk & Resilience & Security 17.6 Water Conservation Planning & Drought Response

18 Chapter 18: Applied Operator Mathematics Workshop

18.1 The Exam Conversion Sheet, Units & Dimensional Analysis 18.2 Distribution & Hydraulic Math Workshop 18.3 Treatment & Wastewater Process Math Workshop

3.4 Wells, Aquifers & Groundwater Hydraulics

Key Takeaways Explain This Topic AI

Well drawdown is static water level subtracted from pumping water level, and specific capacity is well yield in gpm divided by drawdown in feet.

A falling specific capacity at constant yield is the classic indicator of well or screen fouling; a falling static level across seasons indicates aquifer decline.

Confined aquifers have a piezometric surface above the top of the aquifer and can flow artesian; unconfined aquifers have a water table that is the top of the saturated zone.

Well head pressure in psi converts to feet of head by multiplying by 2.31, and one foot of water column equals 0.433 psi.

Groundwater under the direct influence of surface water is identified by microscopic particulate analysis and by rapid temperature, turbidity, or conductivity response to rainfall.

Last updated: September 2026

Why Groundwater Hydraulics Is Heavily Tested

The Source Water category carries 25 questions at T1 and T2, 20 at T3, and 15 at T4 , and the Expected Range of Knowledge lists these as explicit T1-T4 abilities:

  • Ability to calculate well drawdown
  • Ability to calculate well specific capacity
  • Ability to calculate well head pressure
  • Ability to determine water level in a storage facility, reservoir, or well

Knowledge of well components , well depth measurement procedures , well drawdown measurement techniques , the characteristics of aquifers , and the hydrologic cycle

On the distribution side, Wells (New and Abandoned) and Groundwater and Wells appear in two separate categories. In a state where roughly 40 percent of drinking water in a normal year and far more in a drought year comes from groundwater, this is core operator knowledge.

Aquifer Types

Feature Unconfined aquifer Confined (artesian) aquifer

Upper boundary Water table - the top of the saturated zone, at atmospheric pressure An overlying confining layer (aquitard/aquiclude) of clay or unfractured rock

Pressure surface The water table itself Piezometric (potentiometric) surface , which sits above the top of the aquifer

Well behavior Static level equals the water table Static level rises above the aquifer top; if the piezometric surface is above ground, the well flows artesian without pumping

Recharge Direct vertical infiltration Recharge area may be miles away

Contamination vulnerability Higher - direct surface pathway Lower, but a poorly sealed casing defeats the confining layer

Water quality More variable, more likely nitrate More consistent, more likely iron, manganese, hydrogen sulfide, arsenic

Porosity is the fraction of aquifer volume that is void space. Specific yield is the fraction that actually drains under gravity. Permeability (hydraulic conductivity) is how readily water moves through the material. Coarse sand and gravel have moderate porosity but excellent permeability; clay has very high porosity and almost no permeability - which is why clay makes an aquitard, not an aquifer.

The cone of depression is the inverted cone of lowered water surface around a pumping well. Its radius of influence expands with pumping rate and duration and is much wider and flatter in a high-permeability aquifer. Well interference occurs when cones of depression overlap, increasing drawdown in both wells and reducing yield.

Well Components

Working from the aquifer up:

Borehole and gravel pack (filter pack) - graded sand or gravel placed in the annulus opposite the screen to stabilize the formation and reduce sand pumping

  • Well screen (perforated casing) - the intake; slot size is chosen against the formation gradation
  • Blank casing - the conduit from screen to surface

Annular seal (sanitary seal) - cement or bentonite grout in the annulus, the single most important contamination barrier; a failed or short seal is the most common route for surface contamination into a well

  • Surface seal and well pad - sloped concrete apron shedding water away
  • Wellhead - terminates a minimum of 18 inches above finished grade under 22 CCR 64560

Pump - typically a vertical turbine (motor at the surface, line shaft to bowls) or a submersible (motor below the bowls, downhole)

Sounding tube (air line or transducer access) - the port used to measure water levels

Check valve, air/vacuum relief, flow meter, sampling tap (non-threaded), chlorination point, and blow-off to waste

The Four Calculations You Must Be Able to Do

1. Drawdown Drawdown (ft) = Pumping Water Level − Static Water Level \text{Drawdown (ft)} = \text{Pumping Water Level} - \text{Static Water Level} Drawdown (ft) = Pumping Water Level − Static Water Level

Static water level is measured with the pump off long enough to fully recover . Pumping water level is measured while the pump runs at a steady rate. Both are usually reported as depth below a fixed reference point at the wellhead.

Example: static level 84 ft; after 4 hours of pumping the level stabilizes at 152 ft. Drawdown = 152 - 84 = 68 ft .

2. Specific Capacity Specific Capacity (gpm/ft) = Well Yield (gpm) Drawdown (ft) \text{Specific Capacity (gpm/ft)} = \frac{\text{Well Yield (gpm)}}{\text{Drawdown (ft)}} Specific Capacity (gpm/ft) = Drawdown (ft) Well Yield (gpm) ​

Example, continuing above: the well produces 850 gpm at 68 ft of drawdown. Specific capacity = 850 / 68 = 12.5 gpm/ft .

Specific capacity is the single best trend indicator of well health, because it normalizes yield against drawdown. Track it on the same schedule every year.

3. Well Head Pressure and Head Conversion Head (ft) = Pressure (psi) × 2.31 Pressure (psi) = Head (ft) × 0.433 \text{Head (ft)} = \text{Pressure (psi)} \times 2.31 \qquad \text{Pressure (psi)} = \text{Head (ft)} \times 0.433 Head (ft) = Pressure (psi) × 2.31 Pressure (psi) = Head (ft) × 0.433

Example: a discharge gauge reads 62 psi. Head = 62 x 2.31 = 143.2 ft .

4. Well Volume (for disinfection and sanitary sampling) Volume (gal) = 0.785 × D ( ft ) 2 × Depth of water (ft) × 7.48 \text{Volume (gal)} = 0.785 \times D^{2}_{(\text{ft})} \times \text{Depth of water (ft)} \times 7.48 Volume (gal) = 0.785 × D ( ft ) 2 ​ × Depth of water (ft) × 7.48

For a casing diameter in inches, the shortcut 0.0408 × D ( in ) 2 0.0408 \times D^{2}_{(\text{in})} 0.0408 × D ( in ) 2 ​ gives gallons per foot of water column. A 12-inch casing holds 0.0408 x 144 = 5.88 gallons per foot . With 200 ft of water standing in the casing, the well holds about 1,175 gallons - the number you need to compute a chlorine charge for AWWA C654 disinfection.

Reading Well Performance Trends

Observation Most likely cause Operator response

Specific capacity falling, static level unchanged Screen or gravel pack fouling : mineral encrustation (calcium carbonate, iron/manganese oxides) or biofouling by iron bacteria Video log the well; rehabilitate by chemical treatment (acid or specialized biocide) plus mechanical development (surging, jetting, brushing)

Static level falling year over year across the basin Aquifer decline / overdraft Basin-level response under SGMA; deepen pump setting only as an interim measure

Sudden yield loss with normal drawdown Pump wear - worn impellers, worn wear rings, broken line shaft Pull and inspect the pump; compare field head-capacity to the pump curve

Sand or turbidity in discharge Failed screen, undersized gravel pack, over-pumping Reduce rate, inspect screen, consider redevelopment

Rising nitrate or coliform detections Compromised annular seal or nearby septic/agricultural source Video log the casing, evaluate the seal, review the 50-ft protective zone

Rotten egg odor and black water Hydrogen sulfide and sulfate-reducing bacteria Oxidation and filtration; disinfect and evaluate for biofouling

  • Rapid turbidity spikes after rainfall Possible GWUDI Trigger a GWUDI evaluation
  • GWUDI Determinations

Groundwater under the direct influence of surface water must be treated as a surface water for regulatory purposes, which brings the Surface Water Treatment Rules, filtration, and CT requirements into play. Evidence includes:

Microscopic particulate analysis (MPA) finding surface bio-indicators: diatoms, green algae, rotifers, insect parts, plant debris, Giardia or Cryptosporidium

Rapid, correlated response of temperature, turbidity, conductivity, or pH to precipitation or surface water stage

Shallow construction near a surface water body, or a screen set in a hydraulically connected alluvial formation

Stable temperature and mineral chemistry argue against direct influence. A high TDS or hardness result is a mineral fingerprint, not a surface water indicator.