Study guide
6.1 Preliminary Treatment: Screening & Grit Removal
California Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: California Water Regulatory Framework & Certification Ladders
1.1 State Water Board & Regional Boards Structure 1.2 Drinking Water Certification: T1-T5 & D1-D5 Requirements 1.3 Wastewater Certification: Grades I-V & OIT Requirements 1.4 Safe Drinking Water Standards, MCLs & Emerging Contaminants 1.5 California Waterworks Standards (Title 22, Chapter 16) 1.6 Public Water System Types, Permits & the Sanitary Survey
2 Chapter 2: California Water Rights, Title 22 & Environmental Policy
2.1 California Title 22 Recycled Water Standards 2.2 California Environmental Quality Act (CEQA) & Proposition 218 2.3 Water Rights & California Water Resources
3 Chapter 3: Drinking Water Source Quality & Coagulation/Flocculation
3.1 Source Water Quality & Watershed Management 3.2 Coagulation Chemistry & Flash Mixing 3.3 Flocculation & Jar Testing 3.4 Wells, Aquifers & Groundwater Hydraulics 3.5 Raw Water Storage, Clearwells & Reservoir Management
4 Chapter 4: Clarification & Granular Media Filtration
4.1 Sedimentation & Advanced Clarification 4.2 Granular Media Filtration Mechanics & Media Types 4.3 Filter Operation, Backwash Cycles & SWTR Compliance
5 Chapter 5: Disinfection, Oxidation & Advanced Water Treatment
5.1 Chlorination Chemistry & Breakpoint Curves 5.2 Disinfection Kinetics & CT Calculations 5.3 Alternative Disinfection: Ozone, UV & Chlorine Dioxide 5.4 Advanced Treatment: Membranes, AOP & PFAS Adsorption 5.5 Chloramination & Nitrification Control 5.6 Iron & Manganese Removal 5.7 Fluoridation Practice & Compliance 5.8 Corrosion Control Treatment & Water Stability 5.9 Taste & Odor Control and Algal Toxin Management
6 Chapter 6: Wastewater Preliminary & Primary Treatment
6.1 Preliminary Treatment: Screening & Grit Removal 6.2 Primary Clarification Operations 6.3 Primary Sludge Characteristics & Pumping 6.4 Stabilization Ponds, Lagoons & Small-Plant Processes
7 Chapter 7: Secondary Biological Treatment & Activated Sludge
7.1 Activated Sludge Process Fundamentals 7.2 Process Control Parameters: F/M, MCRT & SVI 7.3 Activated Sludge Microbiology & Troubleshooting 7.4 Fixed-Film & Hybrid Biological Processes
8 Chapter 8: Biological Nutrient Removal, Water Reuse & Solids Handling
8.1 Biological Nitrogen Removal: Nitrification & Denitrification 8.2 Biological Phosphorus Removal (EBPR) & Chemical Precipitation 8.3 Anaerobic & Aerobic Digestion 8.4 Sludge Thickening, Dewatering & Biosolids Disposal 8.5 Wastewater Disinfection: Chlorination, Dechlorination & UV
9 Chapter 9: Distribution Systems, Collection Networks & Hydraulics
9.1 Hydraulics, Pressure & Flow Dynamics 9.2 Centrifugal Pumps, Motors & VFDs 9.3 Distribution Network Infrastructure & Cross-Connection Control 9.4 Wastewater Collection Systems, SSMP & FOG Management
10 Chapter 10: Laboratory Analytics, Safety & Water Math
10.1 Water & Wastewater Laboratory Methods 10.2 Laboratory Quality Assurance & Regulatory Reporting 10.3 Chemical Safety, Hazardous Gases & Confined Space 10.4 Essential Water & Wastewater Math for Operators
11 Chapter 11: Federal & California Drinking Water Rules
11.1 The Revised Total Coliform Rule & Assessments 11.2 The Lead and Copper Rule and Service Line Replacement 11.3 Surface Water Treatment Rules & Log Removal Credit 11.4 Stage 1 & Stage 2 Disinfection Byproduct Rules 11.5 Secondary MCLs, Notification Levels & Response Levels 11.6 Public Notification, Consumer Confidence Reports & Recordkeeping
12 Chapter 12: Distribution System Design, Demand & Hydraulics
12.1 System Layout, Pressure Zones & Distribution Maps 12.2 Water Demand, Peaking Factors & Fire Flow 12.3 Distribution Storage: Types, Sizing & Turnover 12.4 Head Loss, C-Factor & Distribution Hydraulic Calculations 12.5 Water Hammer, Surge Control & Air Management
13 Chapter 13: Distribution Equipment Operation, Maintenance & Inspection
13.1 Valves: Types, Operation & Exercising Programs 13.2 Fire Hydrants: Types, Testing & Maintenance 13.3 Water Meters: Types, Accuracy & Meter Management 13.4 Instrumentation, In-Line Sensors, Telemetry & SCADA 13.5 Electrical Systems, Motors & Standby Generators 13.6 External Corrosion, Cathodic Protection & Asset Inspection
14 Chapter 14: Water Mains, Piping & Field Construction
14.1 Pipe Materials & Pipe Selection 14.2 Joints, Fittings, Thrust Restraint & Bedding 14.3 Main Installation, Tapping & Service Line Installation 14.4 Leak Detection, Water Loss Auditing & Main Repair 14.5 Main Cleaning & Maintenance: Flushing, Pigging & Lining 14.6 Excavation, Trench Safety & Utility Locating
15 Chapter 15: Disinfecting Distribution Facilities & Maintaining Water Quality
15.1 Water Main Disinfection (AWWA C651) 15.2 Disinfecting Storage Reservoirs (C652) & Wells (C654) 15.3 Maintaining Distribution Water Quality: Residual, Biofilm & Discolored Water 15.4 Cross-Connection Control Program Administration & Device Testing
16 Chapter 16: Plant Equipment, Chemical Feed & Maintenance
16.1 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 16.2 Gas Chlorination Equipment & Hypochlorite Systems 16.3 Blowers, Compressors & Aeration Equipment 16.4 Flow Measurement Devices: Meters, Weirs & Flumes 16.5 Preventive Maintenance, CMMS & Asset Management
17 Chapter 17: Utility Management, Administration & Emergency Response
17.1 Planning, Organizing, Directing & Controlling a Utility Work Group 17.2 Budgets, Water Rates & Financial Management 17.3 Operator Training, Staffing & Safety Program Development 17.4 Energy Management & Optimization 17.5 Emergency Response Planning, Risk & Resilience & Security 17.6 Water Conservation Planning & Drought Response
18 Chapter 18: Applied Operator Mathematics Workshop
18.1 The Exam Conversion Sheet, Units & Dimensional Analysis 18.2 Distribution & Hydraulic Math Workshop 18.3 Treatment & Wastewater Process Math Workshop
6.1 Preliminary Treatment: Screening & Grit Removal
Key Takeaways Explain This Topic AI
Raw municipal wastewater typically contains 150–300 mg/L BOD5, 150–350 mg/L TSS, 300–600 mg/L COD, 25–60 mg/L TKN, and 4–12 mg/L TP, requiring preliminary removal of coarse debris and abrasive inorganic grit.
Screening equipment spans coarse manual bar racks (1.0–2.0 inch clear openings), mechanically raked bar screens (0.25–1.0 inch clear openings controlled by differential head level sensors), and fine screens (1–6 mm perforated plate or wedge wire).
Screenings volume averages 0.5–5.0 cu ft/MG; screenings washer-compactors return washed soluble fecal organics to the main stream, achieve 50%–70% volume reduction, and dewater solids to 30%–50% dry solids for landfill disposal.
Grit removal targets heavy inorganic particles (silica sand, eggshells, gravel with specific gravity ~2.65 and size >= 0.2 mm / 65 mesh) while maintaining organic solids (SG 1.05–1.20) in suspension.
Horizontal velocity-controlled grit channels utilize proportional flow or Sutro weirs to maintain exactly 1.0 ft/s horizontal velocity (45–60 sec HRT); aerated grit chambers use 3–8 scfm/ft of diffused air to create a helical roll (2–5 min HRT); vortex separators use rotating impellers with short 0.5–1.0 min HRT.
Last updated: August 2026
Purpose & Role of Preliminary Treatment
Preliminary treatment is the initial stage of wastewater processing at the treatment facility headworks. Its primary objective is not significant biochemical transformation, but rather the physical removal or conditioning of coarse debris, rags, floatables, plastics, and heavy abrasive inorganic grit present in raw influent wastewater.
Effective preliminary treatment accomplishes several vital operational objectives:
Equipment Protection: Shields downstream raw sewage pumps, reciprocating sludge pumps, progressive cavity stators, and centrifuge bowls from severe abrasive wear and catastrophic mechanical jamming.
Pipeline & Basin Maintenance: Prevents heavy inert grit (sand, gravel, glass) from accumulating in primary clarifiers, aeration basins, anaerobic digesters, and gravity pipelines where removal requires expensive manual dewatering and confined space entry.
Process Optimization: Eliminates synthetic rags, wet wipes, and plastics that wrap around mixer impellers, foul dissolved oxygen (DO) probes, blind membrane bioreactor (MBR) cassettes, and form unsightly floating scum mats.
Raw Wastewater Characterization & Typical Municipal Concentrations
Municipal wastewater consists of liquid wastes discharged from domestic residences, commercial establishments, light industrial connections, and institutional facilities, combined with varying fractions of storm runoff and groundwater infiltration/inflow (I&I).
- Parameter Typical Range Medium Strength Baseline
- BOD5 (5-Day Biochemical Oxygen Demand) 150 – 300 mg/L ~200 mg/L
- COD (Chemical Oxygen Demand) 300 – 600 mg/L ~400 mg/L (COD:BOD ~2:1)
- TSS (Total Suspended Solids) 150 – 350 mg/L ~220 mg/L
- Settleable Solids 5 – 20 mL/L ~10 mL/L (60-min Imhoff cone)
- Total Dissolved Solids (TDS) 400 – 1,000 mg/L Source water + ~300 mg/L
- TKN (Total Kjeldahl Nitrogen) 25 – 60 mg/L ~40 mg/L (Organic N + N H 3 NH_3 N H 3 )
- Ammonia-Nitrogen ( N H 3 NH_3 N H 3 -N) 15 – 35 mg/L ~25 mg/L
- Total Phosphorus (TP) 4 – 12 mg/L ~7 mg/L
- Fats, Oils & Grease (FOG) 50 – 150 mg/L ~80 mg/L
- pH 6.5 – 8.5 ~7.2
- Alkalinity (as C a C O 3 CaCO_3 C a C O 3 ) 50 – 250 mg/L ~150 mg/L
- Domestic vs. Commercial / Industrial Influences
Diurnal Variations: Domestic wastewater exhibits classic diurnal peaking patterns, with peak morning (07:00–10:00) and evening (18:00–21:00) flows and organic loads, dropping to minimal flow and dilute loading during early morning hours (02:00–05:00).
Industrial Loads: Industrial inputs (food processing, bakeries, metal finishing, breweries) introduce shock organic loadings, extreme pH swings, elevated temperatures, high chemical oxygen demand (COD), or high concentrations of fats, oils, and grease (FOG).
Screening Equipment: Bar Racks, Mechanical Screens & Fine Screens
Screening is the first unit operation encountered by raw wastewater. Screens are classified according to the clear spacing between screening elements. RAW INFLUENT WASTEWATER
- │
- ▼
- ┌───────────────────────────────┐
- │ COARSE BAR SCREENING │
- │ (Manual 1-2" / Mech 0.25-1") │
- └──────────────┬────────────────┘
- │
- ▼
- ┌───────────────────────────────┐
- │ FINE SCREENING (1 - 6 mm) │
- │ (Perforated Drum / Belt MBR) │
- └──────────────┬────────────────┘
- │
- ▼
- ┌───────────────────────────────┐
- │ GRIT REMOVAL SYSTEM │
- │ (Velocity / Aerated / Vortex)│
- └──────────────┬────────────────┘
- │
- ▼
- To Primary Clarifiers / Pumps
- 1. Coarse Manual Bar Racks
Clear Bar Spacing: 1.0 to 2.0 inches (25 to 50 mm) .
Inclination Angle: Positioned at 30° to 45° from horizontal to facilitate manual raking by plant operators using handheld tined rakes.
Application: Typically installed in emergency overflow bypass channels, small packaged facilities (<0.5 MGD), or ahead of mechanical screens during power outages.
Operator Considerations: Manual racks are labor-intensive, create pathogen and splash exposure risks, and require frequent cleaning during rainstorms to prevent upstream sewer surcharging.
2. Mechanically Raked Bar Screens
Clear Bar Spacing: 0.25 to 1.0 inch (6 to 25 mm) .
Inclination Angle: Positioned at 60° to 85° from horizontal (or vertical).
Design Types:
Front-Cleaned, Front-Return: The rake teeth enter the screen bars on the upstream face and pull solids upward to the discharge chute. This prevents solids trapped on the upstream face from being pulled through or jamming the bottom inversion chain.
Back-Cleaned: The cleaning mechanism operates from the downstream clean face, penetrating through the bars to push debris off the upstream side.
Automation & Control:
Differential Head Level Sensor Control: Ultrasonic or bubbler level sensors measure the liquid depth upstream and downstream of the screen. When debris blinds the screen, head loss ( Δ h \Delta h Δ h ) increases. When Δ h \Delta h Δ h reaches 2 to 6 inches (50 to 150 mm) , the PLC automatically initiates a cleaning rake cycle.
Timer Backup: An adjustable cycle timer (e.g., 15 to 30 minutes) initiates periodic raking during low-flow periods to prevent organic solids from settling, turning septic, and producing odors.
High-Level Alarm: Triggers emergency alarms or opens automated bypass gates if head loss exceeds safe channel freeboard.
3. Fine Screens
Clear Openings: 1 to 6 mm (0.04 to 0.25 inches) using perforated plates, continuous travelling mesh belts, or wedge-wire rotary drums (internally or externally fed).
Application: Widely deployed in advanced facilities, particularly upstream of Membrane Bioreactors (MBRs) to prevent hair, lint, and synthetic fibers from braiding around hollow-fiber membranes.
- Screenings Characteristics & Washer-Compactor Processing
- Generation Rates
Screenings volume varies widely based on sewer system type (separate vs. combined), community demographics, and precipitation:
Typical Volume: 0.5 to 5.0 cubic feet per million gallons (cu ft/MG) of wastewater treated ( 3.7 to 37 L/1,000 m 3 3.7\text{ to }37\text{ L/1,000 m}^3 3.7 to 37 L/1,000 m 3 ).
Storm Events: First-flush wet weather events can surge screenings generation up to 10 to 20 cu ft/MG within hours.
Screenings Washer-Compactor (Wash Press)
Unprocessed raw screenings consist of feces, rags, paper, food particles, and hygiene products containing 75% to 90% water and high concentrations of putrescible organic matter. Raw Screenings Infeed ──► [ Washing Zone: High-Pressure Spray ] ──► Washwater + Organics Return
- │ (Back to Plant Headworks)
- ▼
- [ Screw Compactor Press ]
- │
- ▼
- [ Plug Dewatering Cylinder ] ──► Clean, Dry Screenings (30-50% DS)
- (To Disposal Dumpster)
Washing Cycle: Screenings enter a washing hopper where high-pressure wash water and mechanical agitation break up and detach fecal matter and soluble biochemical oxygen demand (BOD), returning these organic nutrients to the wastewater stream for downstream biological treatment.
Compaction & Dewatering: A heavy-duty stainless steel screw auger conveys the washed screenings through an adjustable friction restriction plug (cone).
Performance Metrics:
Volume Reduction: 50% to 70% reduction in total screenings volume.
Weight Reduction: 60% to 80% reduction in hauled weight.
Dewatered Dry Solids: Produces clean, non-putrescible screenings with 30% to 50% Dry Solids (DS) .
Disposal Mandate: Processed screenings must pass the EPA Paint Filter Liquids Test (SW-846 Method 9095B—no free liquid passing through a 60-mesh filter over a 5-minute test period) prior to transport to a permitted municipal solid waste landfill.
Comminutors & In-Line Macerators
Comminutors and macerators (grinders) are motor-driven rotary cutting devices installed directly within wastewater channels or on pump suction piping.
Operating Principle: High-torque, counter-rotating twin hexagonal shafts equipped with hardened cutting teeth shred solids into fine, uniform particles ( 1/4 to 3/8 inch or 6 to 10 mm).
Operational Trade-offs:
Advantage: Eliminates the need for screenings handling, washing, odor control, and landfill transport at unmanned lift stations.
Disadvantage: Grinding does not remove non-biodegradable plastics and synthetic fibers. In aeration basins and digesters, shredded rags re-agglomerate into dense fibrous "rag ropes" and "mops" that wrap around turbine mixers and clog clarifier underflow pumps. Modern California WWTP designs favor complete extraction via screens over comminution.
Grit Removal: Principles & Unit Processes
Grit consists of heavy, abrasive inorganic matter with a specific gravity ( S G SG SG ) significantly higher than organic sewage solids:
Grit Specific Gravity ( S G SG SG ): ≈ 2.65 \mathbf{\approx 2.65} ≈ 2.65 (silica sand, gravel, eggshells, bone fragments, coffee grounds, seeds, metal fragments, mineral silt).
Organic Solids Specific Gravity ( S G SG SG ): ≈ 1.05 to 1.20 \mathbf{\approx 1.05\text{ to }1.20} ≈ 1.05 to 1.20 (fecal solids, grease flocs, food waste).
Target Separation: Standard grit chambers target particles with nominal diameter ≥ 0.2 mm \ge 0.2\text{ mm} ≥ 0.2 mm (65-mesh) or ≥ 0.15 mm \ge 0.15\text{ mm} ≥ 0.15 mm (100-mesh).
1. Velocity-Controlled Horizontal Grit Channels
Horizontal-flow grit channels are long, narrow rectangular channels designed to maintain a strictly controlled horizontal flow velocity of exactly 1.0 ft/s (0.30 m/s) under all flow conditions. Target Horizontal Velocity = 1.0 ft/s ( 0.3 m/s ) \text{Target Horizontal Velocity} = 1.0\text{ ft/s} \quad (0.3\text{ m/s}) Target Horizontal Velocity = 1.0 ft/s ( 0.3 m/s )
Velocity Dynamics:
If velocity > 1.0 ft/s > 1.0\text{ ft/s} > 1.0 ft/s ( > 1.2 ft/s >1.2\text{ ft/s} > 1.2 ft/s ): Grit is swept out of the channel and carries over into primary clarifiers.
If velocity < 1.0 ft/s < 1.0\text{ ft/s} < 1.0 ft/s ( < 0.7 – 0.8 ft/s <0.7\text{–}0.8\text{ ft/s} < 0.7 – 0.8 ft/s ): Light organic matter ( S G ≈ 1.1 SG \approx 1.1 SG ≈ 1.1 ) settles along with the grit, creating septic odors and decomposing in the channel.
Flow Control Devices: Because channel flow ( Q Q Q ) varies diurnally, water depth fluctuates. To maintain constant 1.0 ft/s 1.0\text{ ft/s} 1.0 ft/s velocity, a Proportional-Flow Weir or Sutro Weir is installed at the discharge end. The Sutro weir's curved geometry creates a linear discharge-to-head relationship ( Q ∝ h Q \propto h Q ∝ h ), keeping horizontal cross-sectional velocity constant across varying water depths.
Design Retention Time: Hydraulic Retention Time (HRT) is 45 to 60 seconds ; channel length typically ranges from 30 to 60 feet .
2. Aerated Grit Chambers
Aerated grit chambers are rectangular tanks where coarse bubble diffusers placed along one side near the bottom introduce air, generating a continuous spiral helical roll pattern perpendicular to longitudinal flow. [ Air Diffusers ] ──► Creates Spiral Roll Flow
- │
- ▼
- Transverse Velocity: 1.0 – 2.0 ft/s
- │
- ┌────────┴────────────────────────────────────────┐
- │ Heavy Grit (SG 2.65) ──► Thrown to Bottom Trough │
- │ Organics (SG 1.05-1.2) ──► Lifted in Suspension │
- └─────────────────────────────────────────────────┘
Air Supply Rate: 3 to 8 standard cubic feet per minute per linear foot of channel length (scfm/ft) ( 0.3 to 0.8 m 3 / min ⋅ m 0.3\text{ to }0.8\text{ m}^3/\text{min}\cdot\text{m} 0.3 to 0.8 m 3 / min ⋅ m ).
Hydraulic Retention Time (HRT): 2 to 5 minutes at peak design flow.
Process Adjustments:
If settled grit contains high organic content (gray color, septic odor), increase air flow to increase spiral roll velocity and scour organics.
If fine grit carries over in the effluent, decrease air flow to reduce spiral roll velocity and allow fine grit to settle.
Additional Benefits: Freshens septic sewage, prevents early H 2 S H_2S H 2 S release, and enhances surface grease separation.
3. Vortex Hydrodynamic Grit Separators (e.g., Pista, Tea-Cup)
Vortex separators utilize a cylindrical chamber with a tangential inlet that directs raw wastewater in a circular vortex path.
Mechanics: A motor-driven rotating central impeller (paddle) maintains constant fluid rotational velocity regardless of plant flow variations. Centrifugal force and boundary-layer fluid dynamics drive heavy grit to the chamber floor, directing it down a sloped cone into a center collection hopper. Lighter organics are lifted upward into the top effluent stream.
Design Retention Time: Extremely compact 0.5 to 1.0 minute (30 to 60 seconds) HRT.
Removal Efficiency: Typically > 95 % >95\% > 95% removal of 65-mesh (0.2 mm) sand with minimal organic co-settling.
Grit Handling, Washing & Classification [ Grit Chamber Hopper ] ──► (Air-Lift / Torque-Flow Pump) ──► [ Hydrocyclone Separator ]
- │ (Centrifugal Spin)
- ┌─────────────────────────────────┴─────────────────┐
- ▼ ▼
- [ Top Overflow: Slurry ] [ Bottom Apex: Grit ]
- (Back to Headworks Stream) │
- ▼
- [ Screw Classifier ]
- │ (Washed Dewatering)
- ▼
- [ Dumpster Disposal ]
- (>80% DS, <15% VS)
Grit Slurry Pumping: Settled grit slurry (1% to 3% solids) is extracted from bottom hoppers using air-lift pumps (compressed air injection) or recessed-impeller vortex torque-flow pumps designed to handle abrasive slurries without impeller wear.
Hydrocyclone (Grit Cyclone): The pumped slurry enters a stationary cone tangentially at 15 to 25 psi. Centrifugal force flings dense grit outward against the conical wall, where it discharges out the bottom apex orifice. Lighter organics and water reverse flow up a central core and exit via the top overflow vortex finder back to the plant headworks.
Grit Classifier (Screw or Rake): The concentrated grit discharge drops into an inclined dewatering screw or reciprocating rake classifier. As the screw rotates slowly upward along an inclined trough, grit is washed with clean plant water, draining moisture back into the basin.
Final Disposal Quality: Cleaned, dewatered grit discharged to the disposal container should contain > 80 % to 85 % >80\%\text{ to }85\% > 80% to 85% Total Solids and < 15 % to 20 % <15\%\text{ to }20\% < 15% to 20% Volatile Solids .