Study guide
14.3 Main Installation, Tapping & Service Line Installation
California Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: California Water Regulatory Framework & Certification Ladders
1.1 State Water Board & Regional Boards Structure 1.2 Drinking Water Certification: T1-T5 & D1-D5 Requirements 1.3 Wastewater Certification: Grades I-V & OIT Requirements 1.4 Safe Drinking Water Standards, MCLs & Emerging Contaminants 1.5 California Waterworks Standards (Title 22, Chapter 16) 1.6 Public Water System Types, Permits & the Sanitary Survey
2 Chapter 2: California Water Rights, Title 22 & Environmental Policy
2.1 California Title 22 Recycled Water Standards 2.2 California Environmental Quality Act (CEQA) & Proposition 218 2.3 Water Rights & California Water Resources
3 Chapter 3: Drinking Water Source Quality & Coagulation/Flocculation
3.1 Source Water Quality & Watershed Management 3.2 Coagulation Chemistry & Flash Mixing 3.3 Flocculation & Jar Testing 3.4 Wells, Aquifers & Groundwater Hydraulics 3.5 Raw Water Storage, Clearwells & Reservoir Management
4 Chapter 4: Clarification & Granular Media Filtration
4.1 Sedimentation & Advanced Clarification 4.2 Granular Media Filtration Mechanics & Media Types 4.3 Filter Operation, Backwash Cycles & SWTR Compliance
5 Chapter 5: Disinfection, Oxidation & Advanced Water Treatment
5.1 Chlorination Chemistry & Breakpoint Curves 5.2 Disinfection Kinetics & CT Calculations 5.3 Alternative Disinfection: Ozone, UV & Chlorine Dioxide 5.4 Advanced Treatment: Membranes, AOP & PFAS Adsorption 5.5 Chloramination & Nitrification Control 5.6 Iron & Manganese Removal 5.7 Fluoridation Practice & Compliance 5.8 Corrosion Control Treatment & Water Stability 5.9 Taste & Odor Control and Algal Toxin Management
6 Chapter 6: Wastewater Preliminary & Primary Treatment
6.1 Preliminary Treatment: Screening & Grit Removal 6.2 Primary Clarification Operations 6.3 Primary Sludge Characteristics & Pumping 6.4 Stabilization Ponds, Lagoons & Small-Plant Processes
7 Chapter 7: Secondary Biological Treatment & Activated Sludge
7.1 Activated Sludge Process Fundamentals 7.2 Process Control Parameters: F/M, MCRT & SVI 7.3 Activated Sludge Microbiology & Troubleshooting 7.4 Fixed-Film & Hybrid Biological Processes
8 Chapter 8: Biological Nutrient Removal, Water Reuse & Solids Handling
8.1 Biological Nitrogen Removal: Nitrification & Denitrification 8.2 Biological Phosphorus Removal (EBPR) & Chemical Precipitation 8.3 Anaerobic & Aerobic Digestion 8.4 Sludge Thickening, Dewatering & Biosolids Disposal 8.5 Wastewater Disinfection: Chlorination, Dechlorination & UV
9 Chapter 9: Distribution Systems, Collection Networks & Hydraulics
9.1 Hydraulics, Pressure & Flow Dynamics 9.2 Centrifugal Pumps, Motors & VFDs 9.3 Distribution Network Infrastructure & Cross-Connection Control 9.4 Wastewater Collection Systems, SSMP & FOG Management
10 Chapter 10: Laboratory Analytics, Safety & Water Math
10.1 Water & Wastewater Laboratory Methods 10.2 Laboratory Quality Assurance & Regulatory Reporting 10.3 Chemical Safety, Hazardous Gases & Confined Space 10.4 Essential Water & Wastewater Math for Operators
11 Chapter 11: Federal & California Drinking Water Rules
11.1 The Revised Total Coliform Rule & Assessments 11.2 The Lead and Copper Rule and Service Line Replacement 11.3 Surface Water Treatment Rules & Log Removal Credit 11.4 Stage 1 & Stage 2 Disinfection Byproduct Rules 11.5 Secondary MCLs, Notification Levels & Response Levels 11.6 Public Notification, Consumer Confidence Reports & Recordkeeping
12 Chapter 12: Distribution System Design, Demand & Hydraulics
12.1 System Layout, Pressure Zones & Distribution Maps 12.2 Water Demand, Peaking Factors & Fire Flow 12.3 Distribution Storage: Types, Sizing & Turnover 12.4 Head Loss, C-Factor & Distribution Hydraulic Calculations 12.5 Water Hammer, Surge Control & Air Management
13 Chapter 13: Distribution Equipment Operation, Maintenance & Inspection
13.1 Valves: Types, Operation & Exercising Programs 13.2 Fire Hydrants: Types, Testing & Maintenance 13.3 Water Meters: Types, Accuracy & Meter Management 13.4 Instrumentation, In-Line Sensors, Telemetry & SCADA 13.5 Electrical Systems, Motors & Standby Generators 13.6 External Corrosion, Cathodic Protection & Asset Inspection
14 Chapter 14: Water Mains, Piping & Field Construction
14.1 Pipe Materials & Pipe Selection 14.2 Joints, Fittings, Thrust Restraint & Bedding 14.3 Main Installation, Tapping & Service Line Installation 14.4 Leak Detection, Water Loss Auditing & Main Repair 14.5 Main Cleaning & Maintenance: Flushing, Pigging & Lining 14.6 Excavation, Trench Safety & Utility Locating
15 Chapter 15: Disinfecting Distribution Facilities & Maintaining Water Quality
15.1 Water Main Disinfection (AWWA C651) 15.2 Disinfecting Storage Reservoirs (C652) & Wells (C654) 15.3 Maintaining Distribution Water Quality: Residual, Biofilm & Discolored Water 15.4 Cross-Connection Control Program Administration & Device Testing
16 Chapter 16: Plant Equipment, Chemical Feed & Maintenance
16.1 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 16.2 Gas Chlorination Equipment & Hypochlorite Systems 16.3 Blowers, Compressors & Aeration Equipment 16.4 Flow Measurement Devices: Meters, Weirs & Flumes 16.5 Preventive Maintenance, CMMS & Asset Management
17 Chapter 17: Utility Management, Administration & Emergency Response
17.1 Planning, Organizing, Directing & Controlling a Utility Work Group 17.2 Budgets, Water Rates & Financial Management 17.3 Operator Training, Staffing & Safety Program Development 17.4 Energy Management & Optimization 17.5 Emergency Response Planning, Risk & Resilience & Security 17.6 Water Conservation Planning & Drought Response
18 Chapter 18: Applied Operator Mathematics Workshop
18.1 The Exam Conversion Sheet, Units & Dimensional Analysis 18.2 Distribution & Hydraulic Math Workshop 18.3 Treatment & Wastewater Process Math Workshop
14.3 Main Installation, Tapping & Service Line Installation
Key Takeaways Explain This Topic AI
Installation and Repair and Service Line Installation are two named sub-topics in the SWRCB distribution Water Mains and Piping category.
A wet tap uses a tapping sleeve and valve plus a tapping machine to connect a new branch to a pressurized main without a shutdown.
Direct taps into PVC and thin-wall pipe require a service saddle, and taps must be spaced away from joints and from each other per the manufacturer's requirements.
New mains must be pressure and leakage tested per AWWA C600 or C605, then disinfected under AWWA C651-05 and shown coliform-negative before service under 22 CCR 64580.
Trenchless methods including horizontal directional drilling, pipe bursting, and slip lining reduce surface disruption but require careful locating and pull-force control.
Last updated: September 2026
Open-Cut Installation Sequence
Locate existing utilities. Call 811 (Underground Service Alert) at least two working days ahead, verify markings, and pothole (daylight) critical crossings before machine excavation. Damaging a gas line or a fiber trunk is the most consequential single mistake a water crew can make.
Traffic control and excavation safety. Set the traffic control plan; establish the trench protective system before anyone enters (Section 14.6).
Excavate to line and grade with the specified trench width - wide enough to compact the haunches, narrow enough to limit load on the pipe.
Prepare the foundation and bedding. Over-excavate unstable material; place and shape bedding; dig bell holes.
Inspect and lay pipe. Check each length for damage; clean bell and spigot; lubricate with approved lubricant; insert to the depth mark ; check line and grade continuously.
Install fittings, valves, and hydrants with thrust restraint (blocks against undisturbed soil, or restrained joints).
Haunch and backfill in compacted lifts.
Pressure and leakage test.
Disinfect, flush, and sample.
Tie in, restore surface, and update the map with a red-line as-built.
Separation Requirements
Under 22 CCR 64572 : at least 10 feet horizontally from and 1 foot vertically above any parallel sewer, never in the same trench; crossings at no less than 45 degrees , 1 foot above , with no joints within 8 horizontal feet ; 100 feet from a landfill, wastewater pond, or hazardous waste site; 25 feet from a cesspool, septic tank, leach field, or seepage pit. All distances are measured from the nearest outside edge of each pipe barrel .
Trenchless Methods
Method How it works Best for
Horizontal directional drilling (HDD) A steerable pilot bore is drilled, reamed, and the pipe is pulled back River, freeway, and railroad crossings; long runs under developed areas; usually HDPE because fused joints take the pull
Pipe bursting A bursting head fractures the existing pipe outward while pulling in a new one In-kind or upsized replacement along an existing alignment; excellent for replacing old cast iron and AC in narrow streets
Slip lining A smaller carrier pipe is pulled inside the host pipe; the annulus is grouted Rehabilitating a large main; reduces diameter
Cured-in-place lining (CIPP) A resin-saturated liner is inverted or pulled in and cured Structural or semi-structural rehabilitation without excavation
Cement-mortar or spray-applied polymer lining Cleaning followed by a sprayed lining Restores C-factor in tuberculated mains and stops internal corrosion
Auger boring / jack and bore A casing is jacked while material is augered out Straight crossings under roads and rails
Trenchless controls that matter: accurate utility locating and potholing along the entire bore path, monitoring and limiting pull force so the pipe is not overstressed, managing drilling fluid to avoid an inadvertent surface return (frac-out) into a street or a waterway, and verifying depth and alignment as the bore progresses.
- Tapping
- Wet Tapping (Live Tap)
A wet tap connects a new branch to a pressurized, in-service main with no shutdown and no customer outage:
Install a tapping sleeve around the main and bolt a tapping valve to it.
Pressure test the sleeve and valve before cutting - a leak found afterward means an unplanned shutdown.
Mount the tapping machine on the valve, open the valve, and advance a shell cutter through the main wall.
The cutter's retaining pilot holds the coupon so it is withdrawn rather than left in the main.
Retract the cutter, close the tapping valve , remove the machine, and connect the branch.
Key discipline: account for the coupon . A coupon dropped into a main can lodge in a valve, a meter, or a service and cause a failure nobody can explain later.
Dry Tapping and Direct Tapping
Dry tap - the main is shut down and drained; a hole is cut and a fitting installed. Requires a shutdown and requires disinfection and coliform sampling before return to service.
Direct tap - a corporation stop threaded directly into the pipe wall. Acceptable in ductile iron of adequate wall thickness. Not acceptable in PVC or thin-wall pipe without a service saddle , which distributes the stress; a direct tap into PVC creates a stress riser that can split the pipe.
Tap spacing - keep taps away from bells and joints and from one another, per the manufacturer's minimums (a common rule is at least 18-24 inches between taps and at least 18 inches from a joint), and stagger taps around the circumference rather than lining them up along the top.
Service Line Installation
From main to meter:
Corporation stop at the main, on a saddle where required
Goose-neck or expansion loop to absorb ground movement - historically these were lead , which is why they are a separate service line inventory category
Service line - copper (type K soft is common), HDPE, or PEX; record the material , because the Lead and Copper Rule service line inventory requires the material of both the utility-owned and customer-owned portions
- Curb stop in a curb box at the property line - the utility's single-customer isolation point
- Meter setter, meter, and backflow protection appropriate to the hazard
- Trace wire on non-metallic service lines so the line can be located later
Important
Never connect new copper to remaining lead. A partial lead service line replacement creates a galvanic couple that accelerates lead release and physically disturbs accumulated scale. If a lead line is encountered, the correct action is full replacement , and the customer must receive flushing instructions and a certified point-of-use filter plus follow-up sampling.
Pressure and Leakage Testing
Per AWWA C600 (ductile iron) and C605 (PVC), typically:
Test pressure is commonly 150 percent of working pressure or a specified value such as 150 or 200 psi, held for a defined period (often 2 hours )
Expel all air before testing - trapped air makes the test meaningless and dangerous
Allowable leakage is computed from a standard formula based on pipe diameter, length, number of joints, and test pressure; zero leakage is not the standard for gasketed pipe, but the measured makeup water must be at or below the allowable L = S × D × P 148,000 L = \frac{S \times D \times \sqrt{P}}{148{,}000} L = 148 , 000 S × D × P
where L is allowable leakage in gallons per hour, S is the number of joints, D is nominal diameter in inches, and P is test pressure in psi.
Nobody stands in line with a cap, plug, bend, or dead end during the test.
Disinfection and Return to Service
22 CCR 64580 requires that prior to use, newly installed water mains, or mains taken out of service for maintenance or repair, be disinfected and sampled for bacteriological quality in accordance with AWWA Standard C651-05 , and that samples from new mains be negative for coliform bacteria before the main is placed into service. The methods and the sampling protocol are covered in Section 15.1.