Study guide
8.3 Maintenance of Marking Methods
CBSPD CSIS Certified Surgical Instrument Specialist Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: The CSIS Exam & Care of Surgical Instruments
1.1 CSIS Exam Blueprint, Eligibility & Logistics 1.2 Instrument Composition & Finish 1.3 Grades of Stainless Steel 1.4 Methods to Prevent Instrument Damage
2 Chapter 2: Instrument Anatomy & Naming Conventions
2.1 Anatomy of an Instrument: Jaws, Shanks & Box Locks 2.2 Instrument Naming Conventions & Classification
3 Chapter 3: General Instruments — Identification by Proper Name
3.1 Hemostatic Clamps 3.2 Grasping & Holding Instruments 3.3 Tissue & Thumb Forceps 3.4 Scissors & Other Cutting Instruments 3.5 Needle Holders & Suturing Instruments 3.6 Suction, Dilators, Probes & Accessory Instruments
4 Chapter 4: Retractors, Endoscopic, Robotic & Powered Systems
4.1 Handheld Retractors 4.2 Self-Retaining & Table-Mounted Retractors 4.3 Laparoscopic Instruments & Accessories 4.4 Robotic Instruments & Accessories 4.5 Navigational Systems & Their Instrumentation 4.6 Surgical Instrument Tracking Systems 4.7 Powered Surgical Equipment
5 Chapter 5: Specialty Instrument Sets
5.1 Orthopedic Instruments: Trauma 5.2 Orthopedic Instruments: Total Joints 5.3 Neurosurgical Instruments 5.4 Vascular & Cardiovascular-Thoracic Instruments 5.5 ENT & Dental Instruments 5.6 GU & GYN Instruments 5.7 Plastic & Microsurgical Instruments
6 Chapter 6: Components, Assembly & Configuration of Individual Sets
6.1 Instrument Make-Up for Various Sets 6.2 Count Sheets, Names & Set Configuration 6.3 Assembly Mechanics: Stringers, Protection & Weight
7 Chapter 7: Instrument Inspection & Safety Testing
7.1 Inspection for Cleanliness: Frequency 7.2 Inspection for Cleanliness: Methods 7.3 Staining, Spotting & Corrosion Identification 7.4 Testing Scissors 7.5 Testing Hinged Instruments: Box Locks & Ratchets 7.6 Testing Forceps & Clamps 7.7 Testing Needle Holders 7.8 Inspection & Testing of Laparoscopic Instruments 7.9 Insulation Inspection: Frequency 7.10 Insulation Testing: Methods
8 Chapter 8: Instrument Marking & Specialty Device Inspection
8.1 Acceptable Instrument Identification & Marking Methods 8.2 Correct Application of Instrument Marking Tape 8.3 Maintenance of Marking Methods 8.4 Inspection of Rigid & Semi-Rigid Scopes 8.5 Inspection of Flexible Scopes 8.6 Inspection of Robotic Instruments 8.7 Inspection & Testing of Power Equipment 8.8 Inspection of Harmonic Scalpels & Advanced Energy Devices 8.9 Inspection of Cameras, Light Cords & Optics 8.10 Inspection of Stereotactic Sets 8.11 Inspection of Sigmoidoscope Sets 8.12 Removal From Service, Repair & Replace Decisions
9 Chapter 9: Loaner & Implant Sets and Components
9.1 Loaner Program Fundamentals & Receipt 9.2 Inspection of Loaner Instruments 9.3 Testing of Loaner Instruments 9.4 Set Configuration of Loaner Instruments 9.5 Documentation Process for Loaner & Implant Sets
10 Chapter 10: Ethics in Surgical Instrument Processing
10.1 Professional Ethics & Accountability 10.2 Ethics of Cleanliness 10.3 Ethics of Functionality 10.4 Correct Instrument on the Set 10.5 Completeness of Sets 10.6 Reporting Instrument Damage & Abuse
8.3 Maintenance of Marking Methods
Key Takeaways Explain This Topic AI
Markings are inspected at every assembly for lifting, splitting, discolouration, hardening, and soil accumulation at the edges.
A failing mark is removed completely and replaced, and the surface beneath is inspected for corrosion before re-marking.
Laser and electrochemical etchings are inspected for legibility and scan readability rather than for physical integrity.
A facility marking policy defines the colour scheme, the approved products, the permitted locations, and the replacement criteria.
A systemic pattern of marking failure usually points to processing chemistry, application technique, or an unsuitable product rather than to individual instruments.
Last updated: August 2026
Marking Is a Programme, Not a One-Time Task
A mark applied today will be cleaned, heated, cooled, handled, and dropped hundreds of times. Maintenance is therefore part of the inspection routine, and the CBSPD outline lists it as its own sub-topic for that reason.
What to Inspect, Every Assembly
Marking type Inspect for Fail criteria
Tape Lifting, curling, splitting, discolouration, hardening, brittleness, soil at the edges, unknown extra layers Any lifting, split, or soil accumulation
Dipped / moulded handle Cracking, chipping, separation from the metal at the edge, discolouration, softening Any separation or chip
- Laser etch / 2D code Legibility ; corrosion within the etch; the code still scans Illegible or unscannable
- Electrochemical etch Legibility; surrounding corrosion Illegible; corrosion at the mark
- Anodized colour Wear-through, abrasion damage Not usually a removal criterion; note if size coding is lost
- Marking bands / rings Cracks, stretching, soil beneath Any crack or looseness
The common failure signal across every method is the same: a gap between the mark and the metal . Whether it is a curling tape edge, a lifting dipped handle, or a cracked band, the gap is a crevice, and a crevice on a surgical instrument is a cleaning failure waiting to happen.
Removal and Replacement
The rule is simple and non-negotiable: remove completely, inspect the surface, then re-mark.
Remove all of the old marking , including adhesive residue, using a method compatible with the instrument. Do not use abrasives on anodized or coated surfaces.
Inspect the exposed surface under magnification. This is the only opportunity to see what has been happening under the mark: corrosion, pitting, or staining are common findings on instruments that were taped while damp or that carried a lifting edge.
Reprocess if any soil is found , because a soiled area under a mark means the instrument was not clean when it was marked, or soil wicked in afterwards.
Remove from service if corrosion or pitting is found beneath the mark, per the criteria in Section 7.3.
Re-mark per Section 8.2 on a clean, dry instrument.
Never "top up" a mark. Layering is the single most common maintenance error and it hides everything the inspection is meant to find.
Maintaining Etched Codes
Etched marks do not lift, so their maintenance is about readability :
A code that no longer scans is functionally absent, and the instrument drops out of the tracking system silently — the worst kind of failure, because the record simply stops updating.
Codes are checked for wear from abrasion, for soil filling the etch, and for corrosion within the etched area , which can occur if the etching process compromised the surface.
A code that has become unreadable is re-marked by the vendor , not by scratching over it.
Instruments failing to scan should be logged; a cluster in one area of the department points to a specific abrasive process or storage practice.
The Facility Marking Policy
A marking programme without a written policy degrades into folklore. The policy should define:
The colour scheme — which colour means what, facility-wide, with no service-specific exceptions.
Approved products — specific marking tapes, bands, and vendors, validated for the sterilization methods in use.
Permitted locations by instrument type, and the prohibited locations.
Application technique (Section 8.2).
Inspection and replacement criteria — what constitutes a failing mark.
Who may apply marks , and any training requirement.
Documentation — where marking and re-marking are recorded, and how unique codes are managed in the tracking system.
What is prohibited — rubber bands, adhesive labels, nail polish, marker, paint, bench engraving.
Reading Patterns
As everywhere else in this content area, the specialist's contribution is pattern recognition:
Pattern Likely cause
Tape hardening and splitting across many sets Chemistry too aggressive, or a product not validated for the cycle in use
Tape lifting shortly after application, department-wide Application technique: damp instruments, insufficient overlap, or unsealed ends
- Corrosion consistently found under removed tape Instruments being marked while damp
- Dipped handles chipping on one service's sets Handling or storage practice in that service
Codes failing to scan on one instrument family Abrasion from a specific process, or the code placed on a wear surface
Each of these is fixed once, at the cause, rather than instrument by instrument forever.
Building the Replacement Schedule
Marking maintenance is a scheduled programme rather than a reaction to obviously failed tape, and the exam expects you to describe how a department runs one.
The practical model is inspect at every assembly, replace on a defined cycle or on failure, whichever comes first . Because tape degrades with cycles rather than with calendar time, high-turnover sets need attention more often than rarely used ones. Many departments set a periodic sweep — quarterly or semi-annually — in which every instrument in a set has its tape stripped, the underlying metal inspected, and fresh tape applied, and they schedule these sweeps around low-demand periods.
Record what you do. Noting the date a set was re-taped lets you see whether tape is failing faster than expected, which usually points to application technique or to a chemistry that is attacking the adhesive.
Inspecting Each Method for Its Own Failure Mode
The condition you look for differs by method, and mixing them up is a common error.
Tape fails by lifting at the edge, fraying, splitting, discolouring, or loosening so it rotates on the shank . Any of these means removal and replacement, and lifting matters most because it admits moisture and shields soil.
Dipped or coated handles fail by chipping, cracking, peeling, or bubbling , which exposes bare metal and creates a crevice. A chipped coating cannot be patched in the department and routes to the vendor.
Etched data matrices fail by becoming illegible — polished away by repeated processing, obscured by staining or corrosion, or physically damaged. An unreadable code drives manual workarounds that defeat tracking, so route it for re-marking rather than tolerating it.
Anodised colour fades under strongly alkaline chemistry; widespread fading across many items is a chemistry problem, not an instrument problem.
Reading the Pattern Behind Marking Failures
Because marking failures are numerous and visible, they are an unusually good early-warning signal about the process as a whole, and the specialist who reads them adds real value.
If tape is lifting across many instruments at once , suspect the application technique being taught, the curing step being skipped, or a detergent whose pH is attacking the adhesive. If coatings are chipping widely , suspect mechanical handling — trays overloaded, instruments tipped from one container to another. If etched codes are fading across a set , suspect abrasive cleaning practice or a chemistry issue. If marks are disappearing from one specific set only , look at how that set is used and who processes it.
In every case, report the pattern rather than only fixing the instances. Replacing tape repeatedly without addressing the cause consumes labour indefinitely.