Study guide
Surface Disinfection, Spills, Waste, and Supplies
CCHT Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Orientation, Eligibility, and Exam Strategy
Official Sources and Exam Purpose Eligibility, Application Documents, and Training Verification Exam Format, Fees, Scoring, Practice Exam, and Permit Timing Blueprint and Cognitive-Level Strategy State/Federal Compliance and CMS Context 4-8 Week Post-Training Study Plan
2 Kidney Disease, Hemodialysis Principles, and Adequacy
Kidney Functions and ESRD Basics Hemodialysis Goals and Transport Principles Uremia, Fluid Overload, Electrolytes, and Acid-Base Context Dialysis Adequacy: Kt/V, URR, Treatment Time, and Adherence Pre/Post Weights, Target Weight, and Fluid Gains Patient Education for Diet, Fluid, Medications, and Treatment Adherence
3 Clinical Assessment and Pre-Treatment Safety
Pre-Treatment Assessment and Vital Signs Access Assessment and Signs of Access Failure Fluid Status and Blood Pressure Relationship Prescription Verification and Treatment Setup Checks Aseptic Technique in Patient Care Red Flags Requiring RN Escalation Before Treatment
4 Vascular Access, Cannulation, and Treatment Initiation
AV Fistula, AV Graft, and Catheter Comparison Cannulation Principles, Needle Direction, and Asepsis Initiating Hemodialysis with AV Access Catheter Precautions and Facility Protocol Boundaries Heparin Protocol Awareness and Scope Boundaries Early Treatment Monitoring After Initiation
5 Treatment Monitoring, Complications, and Discontinuation
Intra-treatment Monitoring and Vital Signs Hypotension, Cramps, Nausea, Headache, and Chest Pain Blood Loss, Infiltration, Clotting, Air, Hemolysis, and Fever Volume Status and UF Troubleshooting Discontinuing Treatment and Post-Access Care Post-Treatment Assessment, Documentation, and Escalation
6 Labs, Medications, Specimens, and Patient Education
Common Dialysis Labs Specimen Processing and Chain of Custody Medication Awareness Within Technician Role Anemia, Mineral Bone, Nutrition, and Fluid Education Teach-Back and Scope Limits Documentation of Education and Abnormal Findings
7 Technical Systems, Extracorporeal Circuit, and Machine Operation
Extracorporeal Circuit Components Dialyzer, Blood Pump, Pressures, Air Detector, and Clamps Machine Setup According to Prescription Conductivity, Temperature, pH, and Independent Checks Alarm Recognition and First Safe Actions Equipment Adverse Events and Documentation
8 Water Treatment, Dialysate, Reuse, and Equipment Safety
Water Treatment Principles and Monitoring RO, Carbon, Softener, and Microbiology Concepts Dialysate Concentrates and Powder Mixing Disinfection, Cultures, and QC Checks Reprocessed Dialyzers Where Applicable Equipment Safety: Stop, Report, and Document
9 Environment, Infection Control, and Emergency Preparedness
Standard Precautions and Hand Hygiene PPE, Bloodborne Pathogens, Isolation, and Vaccinations Surface Disinfection, Spills, Waste, and Supplies Body Mechanics and Patient Transfer Safety Emergency Exits, Fire Safety, and Environmental Hazards Disasters, Water and Power Failures, and Communication
10 Role Responsibilities, Documentation, and Professional Communication
Scope and Team Roles Privacy, Dignity, Confidentiality, and Boundaries Verbal and Nonverbal Communication Documentation of Treatment Outcomes and Adverse Events Quality Improvement and Chain of Reporting Ethical Behavior and Patient Advocacy Within Role
11 Integrated CCHT Domain Review and High-Yield Scenarios
Mixed Clinical, Technical, Environment, and Role Scenarios Application-Level Item Strategy Blueprint-Weighted Practice Blocks High-Risk Distractors and Unsafe Shortcuts Error Log by Domain and Cognitive Level Final Weak-Domain Repair
12 Exam Day, Retesting, Recertification, and Career Next Steps
Final 30/14/7 Day Plan Exam-Day Checklist, ID, Permit, and Time Use Score Report, Subarea Breakdown, and Retest Planning Recertification Every Three Years by CE and Work Experience CCHT-A Pathway and Advanced Practice Considerations Maintaining Competence and Staying Within Rules
Surface Disinfection, Spills, Waste, and Supplies
Key Takeaways Explain This Topic AI
The dialysis station is treated as contaminated after every treatment: surfaces without visible blood get low-level disinfection (an EPA-registered hospital disinfectant, kept WET for the label contact time), and anything with visible blood gets intermediate-level disinfection (a tuberculocidal disinfectant or 1:100 bleach) before the next patient.
Visible blood spills get intermediate-level disinfection: wearing gloves, clean immediately with a cloth soaked in a tuberculocidal disinfectant or 1:100 bleach (300-600 mg/L free chlorine), put the cloth in a leakproof container, then apply disinfectant a second time with a new cloth.
Sharps go into puncture-resistant containers, regulated/biohazard waste is bagged separately from regular trash, and clean supplies are never stored with or near contaminated items.
Disinfectant and germicide chemicals (bleach, formaldehyde, peracetic acid) require labels, an SDS, ventilation, and PPE; never mix chemicals - bleach plus ammonia or acid releases toxic gas.
The best answer protects patients first, controls the exposure, uses the approved product at correct concentration and contact time, and communicates through the chain of command.
Last updated: October 2026
Station Turnover: Clean THEN Disinfect
After a treatment, the entire dialysis station is treated as contaminated until it is cleaned and disinfected per policy. High-touch surfaces include the chair, machine control panel and touch screen, clamps, blood-pressure equipment, IV poles, side tables, call devices, and any surface gloves touched .
Two distinct steps are tested. Cleaning physically removes visible blood and soil using detergent - organisms cannot be reliably killed under a layer of dried blood. Disinfection then kills remaining organisms, and CDC's dialysis recommendations set the level by what you see: surfaces without visible blood get low-level disinfection (soap, detergent or detergent germicide, or an EPA-registered hospital disinfectant per facility policy), and anything with visible blood gets intermediate-level disinfection (a tuberculocidal hospital disinfectant or 1:100 bleach ). The order is always clean first, disinfect second .
Contact time is the make-or-break detail
A disinfectant only works if the surface stays visibly wet for the full label contact time - often several minutes. If it dries too soon, the kill is incomplete and the label requires reapplication . "Spray and immediately wipe dry" is a classic wrong answer. Between patients, allow the product its dwell time before placing the next patient.
Common dialysis surface disinfectants and concentrations:
Product Typical use Note
EPA-registered hospital disinfectant (or soap, detergent or detergent germicide) Routine surfaces with no visible blood (low-level) Follow label dilution and dwell time
1:100 bleach (300-600 mg/L free chlorine) Visible blood, including spills (intermediate-level) Mix fresh per policy; observe contact time
EPA-registered tuberculocidal disinfectant Visible blood, including spills (intermediate-level) Follow label dilution and dwell time
CDC's figure for blood is 1:100 bleach; CMS surveyor guidance accepts 1:100 or stronger.
Cleaning vs. disinfection vs. machine internal disinfection
Three terms are sometimes confused on the exam:
Cleaning removes visible soil and organic matter with detergent. It precedes disinfection and is never skipped.
Disinfection kills most organisms on a surface; low-level disinfection (general-purpose hospital disinfectants) kills most bacteria and is used on surfaces without visible blood, while intermediate-level disinfection (a tuberculocidal hospital disinfectant or 1:100 bleach) kills bacteria and most viruses and is required wherever blood is visible.
Sterilization destroys all microbial life and is reserved for reprocessing where required.
Beyond surfaces, the dialysis machine's internal fluid pathways are disinfected on a schedule using heat or chemical germicides (such as bleach, citric acid, or peracetic-acid products) per the manufacturer's protocol. Residual disinfectant must be rinsed and tested to confirm none remains before the next patient is connected - a residual-test failure means the machine is not used.
Blood Spills
A blood spill is both an environmental hazard and an infection-control breach . Restrict traffic through the area. Then follow the CDC sequence for dialysis units, which the Medicare rules adopt: wear gloves (add gown and face/eye protection if splashing is possible), immediately clean the spill with a cloth soaked in a tuberculocidal disinfectant or 1:100 bleach (300-600 mg/L free chlorine), place the cloth in a leakproof container , and once all visible blood is gone, apply disinfectant a second time with a new cloth , allowing the label contact time. Dispose of contaminated material as regulated waste per policy.
Escalate to the RN, charge nurse, or safety lead for large spills, chemical exposures, patient or employee injury, or any uncertainty about the product . The technician must never mix chemicals or improvise a disinfectant.
A frequent exam point: a blood spill gets two applications of disinfectant. The first, with a soaked cloth, removes the visible blood; the second, with a new cloth, disinfects the cleaned surface. A single wipe that leaves blood behind, or a low-level cleaner, does not meet the rule. When the spill is cleaned during station turnover, no patient should be at the station.
Waste Streams and Supply Separation
Keeping waste streams separate is both a safety rule and a regulatory one.
Sharps (needles, fistula needles, lancets, broken glass) go directly into puncture-resistant, leak-proof, labeled sharps containers.
Regulated medical / biohazard waste (blood-saturated items, used bloodlines, dialyzers per policy) goes in labeled biohazard bags , separate from regular trash.
General trash stays separate from regulated waste - over-bagging clean trash as biohazard wastes money and disposal capacity; under-bagging is a hazard.
Clean supplies are never stored with or near trash, used tubing, used dialyzers, or contaminated equipment.
Overfilled containers raise the risk of needlesticks and spills. If a sharps or waste container is at the fill line or leaking , follow the facility process to remove it from service and notify the right person. Never push contents down by hand.
Chemical Safety
Dialysis units use germicides and disinfectants that irritate skin, eyes, and airways - bleach (sodium hypochlorite), formaldehyde, peracetic/peracetic-acid-based products, citric acid, and glutaraldehyde among them. Chemical safety requires legible labels, correct storage, task-appropriate PPE, ventilation, spill kits, and ready access to the Safety Data Sheet (SDS) for every product.
The single most dangerous mistake is mixing chemicals : bleach plus ammonia releases chloramine gas , and bleach plus acid releases chlorine gas - both can be life-threatening. A chemical spill is not handled like a water spill.
Hazard Safe exam response
Blood on the floor Restrict the area; clean with PPE, then disinfect with the approved product and contact time
- Unknown chemical leak/odor Keep people away, ventilate, consult the SDS, and report per safety protocol
- Sharps container overfilled Remove from service per policy; do NOT push contents down
- Two cleaning chemicals on the same surface Stop - never mix; flush/ventilate and report if mixing occurred
- Clean supplies near waste Protect clean status or discard per policy
The SDS tells you the product's hazards, required PPE, first-aid steps, and spill/cleanup procedure - know where the SDS binder or system is located.