Study guide

Exam Domains and Weights

Cisco Certified Network Associate CCNA

Track your progress as you read

Finished sections get a check mark.

1 Introduction

About the CCNA 200-301 Exam Domains and Weights Study Strategies and Tips

2 Chapter 1: Network Fundamentals (20%)

1.1 Network Components 1.2 Network Topology Architectures 1.3 Physical Interfaces and Cabling 1.4 TCP vs. UDP 1.5 IPv4 Addressing and Subnetting 1.6 IPv6 Addressing and Prefix 1.7 Wireless Principles 1.8 Virtualization Fundamentals 1.9 Switching Concepts 1.10 OSI and TCP/IP Reference Models 1.11 Verifying IP Parameters on Client Operating Systems

3 Chapter 2: Network Access (20%)

2.1 VLANs — Configuration and Verification 2.2 Trunking and 802.1Q 2.3 Layer 2 Discovery Protocols (CDP and LLDP) 2.4 EtherChannel (Link Aggregation) 2.5 Spanning Tree Protocol (STP) and RSTP 2.6 Wireless Architectures and AP Modes 2.7 Network Access Troubleshooting 2.8 Inter-VLAN Routing — Deep Dive

4 Chapter 3: IP Connectivity (25%)

3.1 Routing Table Components 3.2 Router Forwarding Decisions 3.3 IPv4 and IPv6 Static Routing 3.4 Single-Area OSPFv2 — Concepts 3.5 Single-Area OSPFv2 — Configuration 3.6 First Hop Redundancy Protocols (FHRP) 3.7 Troubleshooting IP Connectivity 3.8 OSPF Troubleshooting Scenarios

5 Chapter 4: IP Services (10%)

4.1 NAT (Network Address Translation) 4.2 DHCP and DNS 4.3 NTP, SNMP, and Syslog 4.4 QoS Fundamentals 4.5 TFTP/FTP and Remote Access 4.6 IP Services — Comprehensive Review

6 Chapter 5: Security Fundamentals (15%)

5.1 Key Security Concepts 5.2 Device Access Control and Password Policies 5.3 VPN Fundamentals 5.4 Access Control Lists (ACLs) 5.5 Layer 2 Security Features 5.6 Network Security Best Practices and Hardening 5.7 Threat Mitigation and Incident Response

7 Chapter 6: Automation and Programmability (10%)

6.1 Impact of Automation on Network Management 6.2 Controller-Based and Software-Defined Architectures 6.3 AI and Machine Learning in Network Operations 6.4 REST-Based APIs 6.5 Configuration Management Tools 6.6 JSON-Encoded Data 6.7 Automation and Programmability — Comprehensive Review

Exam Domains and Weights

Key Takeaways Explain This Topic AI

IP Connectivity (25%) is the single heaviest domain — routing is your top priority.

Network Fundamentals (20%) and Network Access (20%) together make up 40% of the exam.

Security Fundamentals (15%) spans ACLs, AAA, Layer 2 hardening, VPN concepts, and wireless security.

IP Services and Automation each carry 10%; do not skip Automation despite its low weight.

Questions appear in random order, not grouped by domain, so you must context-switch constantly.

Last updated: June 2026

CCNA 200-301 v1.1 Domains and Weights

The blueprint splits into six domains with fixed percentage weights. Cisco does not reveal exact per-domain question counts, but weights map closely to how many items you will see, so they drive study allocation. Memorize these six numbers — they sum to 100%.

  • # Domain Weight Approx. items (of ~100)
  • 1 Network Fundamentals 20% ~20
  • 2 Network Access 20% ~20
  • 3 IP Connectivity 25% ~25
  • 4 IP Services 10% ~10
  • 5 Security Fundamentals 15% ~15
  • 6 Automation & Programmability 10% ~10
  • Domain 1 — Network Fundamentals (20%)

The conceptual bedrock. High-yield subtopics:

Device roles: routers, Layer 2/3 switches, next-gen firewalls, IPS, access points, WLAN controllers, endpoints, servers, PoE.

Topologies: two-tier (access/distribution+core collapsed), three-tier, spine-leaf, SOHO, WAN, on-prem vs cloud.

Cabling/interfaces: single-mode vs multimode fiber, copper UTP categories, when to choose each.

TCP vs UDP: connection-oriented handshake/sequencing vs connectionless; know which apps use each.

IPv4 subnetting and RFC 1918 private ranges (10.0.0.0/8, 172.16.0.0/12, 192.168.0.0/16).

IPv6: global unicast (2000::/3), unique local (FC00::/7), link-local (FE80::/10), multicast (FF00::/8), EUI-64, SLAAC.

Wireless RF: non-overlapping 2.4 GHz channels 1, 6, 11.

Virtualization: VMs, containers, type-1 vs type-2 hypervisors.

Study Tip: Subnetting lives here but bleeds into every domain. Master it first; routing, VLAN design, NAT, and ACLs all assume instant subnet math.

Domain 2 — Network Access (20%)

Layer 2 switching and wireless:

VLANs across multiple switches, access ports, default/data/voice VLANs, inter-VLAN routing.

Trunking: 802.1Q tagging, native VLAN (untagged — a classic mismatch trap), DTP awareness.

Spanning Tree: RSTP (802.1w), root-bridge election by lowest bridge ID, port roles/states, PortFast, plus the v1.1 hardening features root guard, loop guard, BPDU guard, BPDU filter .

EtherChannel: Layer 2/3 bundles, LACP (open standard) vs PAgP (Cisco) vs static "on".

Discovery: CDP (Cisco) and LLDP (open standard).

Wireless: autonomous, lightweight/split-MAC with a WLC, cloud-managed APs; basic WLAN/GUI setup.

Common Trap: A native-VLAN mismatch on a trunk does not drop the link — it silently merges VLANs and triggers CDP/STP warnings. Expect a troubleshooting item on exactly this.

Wireless management questions also frequently contrast deployment models: an autonomous AP holds its own config, while a lightweight/split-MAC AP offloads control to a WLC via CAPWAP, centralizing policy. Know that LACP and LLDP are the open-standard halves of their respective pairs (PAgP and CDP are Cisco-proprietary) — Cisco loves a "which is vendor-neutral" item.

Domain 3 — IP Connectivity (25%) — Highest Weight

Routing and the forwarding decision. Spend the most time here.

Routing table anatomy: prefix, mask, next hop, administrative distance (connected 0, static 1, OSPF 110, RIP 120, EIGRP internal 90), metric, route source code, gateway of last resort.

Forwarding logic: longest-prefix match wins first; ties broken by lowest AD, then lowest metric.

Static routing: default (0.0.0.0/0), network, host (/32), and floating static (higher AD as backup).

OSPFv2 single-area: router ID selection (manual > highest loopback > highest active interface), neighbor adjacency states, DR/BDR election on broadcast networks, cost = reference-bw / interface-bw (default reference 100 Mbps).

First-hop redundancy: HSRP, VRRP, GLBP — concepts and roles only, not configuration.

  • Route source Default AD
  • Connected 0
  • Static 1
  • EIGRP (internal) 90
  • OSPF 110
  • RIP 120

Worked example: A router learns 10.1.1.0/24 via OSPF (AD 110) and 10.1.1.0/26 via RIP (AD 120). It installs both — longest-prefix match means the /26 is preferred for 10.1.1.0–63 regardless of the higher AD, because AD only breaks ties between identical prefixes.

Domain 4 — IP Services (10%)

The "easy points" if you drilled them:

NAT/PAT: static NAT, dynamic NAT pools, PAT overload (many private to one public via port translation).

DHCP: DORA (Discover, Offer, Request, Ack), relay/ip helper-address, pools.

NTP stratum hierarchy; DNS forward/reverse; SNMP v2c vs v3 (v3 adds auth/encryption), GET/SET/TRAP.

Syslog severity 0–7: Emergency, Alert, Critical, Error, Warning, Notice, Informational, Debug — mnemonic "Every Awesome Cisco Engineer Will Need Ice-cream Daily."

QoS: per-hop behaviors, DSCP marking, queuing basics.

Domain 5 — Security Fundamentals (15%)

Concepts: threat vs vulnerability vs exploit; common attacks (MAC flooding, ARP spoofing, DHCP starvation).

Device hardening: enable secret, service password-encryption, SSH over Telnet.

ACLs: standard (1–99, source only) vs extended (100–199, source+dest+port); implicit deny-all at the end.

Layer 2 defense: port security, DHCP snooping, dynamic ARP inspection.

AAA: TACACS+ (TCP 49, full command authorization, Cisco) vs RADIUS (UDP, combines auth+authz).

Wireless security: WPA2 vs WPA3 , 802.1X/EAP, PSK.

Domain 6 — Automation & Programmability (10%)

Controller-based vs traditional networking; control plane vs data plane; overlay/underlay/fabric.

Northbound APIs (controller to apps, often REST/JSON) vs southbound APIs (controller to devices).

REST verbs GET/POST/PUT/DELETE; reading JSON key/value and arrays.

Ansible (agentless, YAML, push) and Terraform (declarative IaC); plus v1.1 AI/ML in operations.

On the Exam: Items are shuffled across domains, never grouped. A subnet question, a WPA3 question, and an OSPF sim can appear back-to-back, so practice rapid context switching.

CCNA 200-301 Exam Domain Weights