Study guide

4.1 Digital Audio Systems, Interfaces, and Power

AAERT Certified Electronic Reporter CER

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Ethical Obligations

1.1 Current Exam Blueprint and Ethical Conduct 1.2 Conflicts of Interest and Appearance of Impropriety 1.3 Gifts, Fees, Accuracy, and Record Duties

2 Chapter 2: Confidentiality and Information Control

2.1 Confidentiality and Non-Disclosure Agreements 2.2 Job-File Security, Equipment Protection, and HIPAA 2.3 Audio Requests, Sealed Material, and Controlled Release

3 Chapter 3: Professional Behavior

3.1 The Impartial Reporter and Professional Client Service 3.2 Courtroom, Non-Courtroom, and Remote Etiquette 3.3 Demeanor, Appearance, Punctuality, Attention, and Disruptions

4 Chapter 4: Digital Audio Hardware

4.1 Digital Audio Systems, Interfaces, and Power 4.2 Microphone Types, Pickup Patterns, Cost, Cables, and Connectors 4.3 Multi-Channel Assignment and Channel Isolation 4.4 Audio Levels and Recording Peripherals

5 Chapter 5: Software, Annotations, Setup, and Testing

5.1 Recording Software, Confidence Monitoring, Playback, Realtime, and ASR 5.2 Speaker Changes, Abbreviations, Timestamps, and Annotation Priorities 5.3 Equipment Setup in Live, Dead, and Variable Rooms 5.4 Testing Installed and Mobile Equipment

6 Chapter 6: Reliability and Reporter Duties

6.1 Basic Troubleshooting and Technical Escalation 6.2 Audio and Computer Maintenance 6.3 Participant Instructions, Record Status, Clarification, and Oaths 6.4 Remote and Hybrid Proceedings

7 Chapter 7: Collaborators, Exhibits, and Transcript Orders

7.1 Working with Interpreters 7.2 Working with Legal Videographers 7.3 Physical and Electronic Exhibits and Chain of Custody 7.4 Transcript Orders, Roughs, Expedites, Originals, Copies, and Estimates

8 Chapter 8: Transcript Production Workflow

8.1 Accurate Transcript Production and Special Record Events 8.2 Pre-Proceeding Meetings, Appearances, Read-Ons, and Stipulations 8.3 Post-Proceeding Spellings, Job Information, Distribution, Archival, and Retention

9 Chapter 9: Federal Rules and Types of Proceedings

9.1 Federal Transcript Orders and Rule 30 Review 9.2 Trials, Hearings, and Court Proceedings 9.3 Depositions, EUOs, Arbitrations, Mediations, Meetings, and Statements 9.4 Order of Proceedings and the Reporter's Role

10 Chapter 10: Case Life Cycle and Participants

10.1 Civil and Criminal Case Life Cycles 10.2 Parties and People in Proceedings 10.3 Witness Types and Testimony 10.4 Reading Legal Documents Relevant to Reporters

11 Chapter 11: Jurisdiction, Case Law, and Trials

11.1 Jurisdiction, Venue, and Civil versus Criminal Proceedings 11.2 Case Law and Citation Elements 11.3 Jury Selection and Bench versus Jury Trials 11.4 Sidebars, Bench Conferences, and In-Camera Proceedings

12 Chapter 12: Legal Terminology

12.1 Core Courtroom Actions and Roles 12.2 Civil Pleadings, Discovery, and Remedies 12.3 Criminal Procedure Terminology 12.4 Evidence, Foundations, Privilege, and Objections

13 Chapter 13: Latin and Medical Terminology

13.1 Common Latin Legal Terms 13.2 Medical Word Building, Positions, Tests, and Treatment Terms 13.3 Body Systems, Pathology, and Diagnostic Language

4.1 Digital Audio Systems, Interfaces, and Power

Key Takeaways Explain This Topic AI

A reporting signal path runs from sound source through microphone, cable or wireless link, preamplifier or interface, software, storage, and confidence monitoring.

ASIO is a low-latency Windows audio-driver architecture, while a mixer or audio interface is physical hardware.

Power planning includes primary power, compatible supplies, charged batteries, surge protection where appropriate, and a tested continuity plan.

Preparedness means selecting and testing a complete system for the actual courtroom, conference, meeting, or remote environment.

Last updated: September 2026

Follow the signal from speaker to saved file

Digital recording begins as acoustic energy. A microphone converts sound-pressure changes into an electrical signal. A preamplifier raises the low microphone-level signal; a mixer or audio interface routes it, may convert it from analog to digital, and sends it to the computer. A driver allows the operating system and recording application to communicate with the device. The application assigns inputs to tracks or channels and writes data to storage. Confidence monitoring returns the already-recorded signal to the reporter.

Use this path when troubleshooting:

speaker → microphone → cable/link → preamp/interface → driver → recording software → file/storage → confidence monitor

A meter moving at the input but not on the armed track points to routing or software configuration. A clean direct-monitor signal paired with distorted recorded playback points farther downstream. Silence everywhere may begin with microphone power, cable, mute, input selection, or the source itself. Isolate one stage at a time.

Mixers, interfaces, and ASIO

A mixer combines, routes, and adjusts multiple signals. An audio interface provides input/output and analog-to-digital conversion for a computer; many devices combine both functions. Inputs must match the source level and connector. Plugging a line-level output into a sensitive microphone input can overload it, while feeding a low microphone signal into an input expecting line level may be too quiet.

Audio Stream Input/Output (ASIO) is a driver protocol commonly used on Windows for low-latency, multichannel audio. It is not a mixer and not a connector. The reporter should know which approved driver the application expects, which device is selected, and whether an operating-system update changed permissions or routing. Do not install a new driver moments before a live job unless the approved recovery plan requires it and testing is possible.

Equipment by environment

Environment Planning questions

Courtroom Is there an installed sound feed? Which microphones and channels are available? Who controls the system?

Conference room Where will participants sit? Are additional microphones and cable protection needed?

Meeting or arbitration Who presides, and are public-address and recording feeds separate?

Remote How are local and far-end voices routed? Can each path be monitored and recorded?

Hybrid How will room microphones, platform returns, and echo control interact without loops?

Do not assume that a venue's public-address system produces a record-quality feed. Obtain authorization before connecting to installed equipment and test the actual recording return. Avoid connecting two outputs together or creating feedback loops. Label adapters and cables by function so a hurried substitution does not introduce the wrong level or connector.

Power sources and continuity

Possible sources include building mains, device batteries, an approved uninterruptible power supply (UPS), and backup equipment with its own power. A UPS can bridge a short outage and permit an orderly transition; its rating and tested runtime must support the connected load. Do not overload circuits, defeat grounding, daisy-chain unsafe adapters, or block emergency paths.

A pre-job power check covers:

  • correct manufacturer-rated supplies and voltage;
  • fully charged internal and spare batteries;
  • known battery health rather than a displayed percentage alone;
  • safe cable routing and strain relief;
  • power-saving settings that could sleep or throttle the computer;
  • the effect of losing mains power on the interface, microphones, network, and storage; and

a practiced method to continue or pause the record under authority.

Preparedness is system-level

Carry approved spares that address likely single failures: cables, adapters, microphones, storage, batteries, and a backup capture device as the assignment requires. Verify available disk space, system time, job metadata, channel assignments, monitoring output, and backup destination. Keep a contact path for technical escalation. A case full of untested gadgets is not preparedness; a documented, compatible, rehearsed system is.

The exam will often present a tempting component-only fix. Trace the full path, avoid changes that risk the live record, and select the response that restores verified capture with the least disruption.

Exam application

If every microphone is visible in the mixer's meters but the recording application displays no inputs, replacing all microphones wastes time and adds risk. The common point is downstream: device selection, driver, routing, permissions, or software state. If only one interface input is silent, a source-specific check makes more sense. Practice drawing the signal path and circling the last verified stage. The component immediately after that stage is the first logical area to inspect, while the backup and current files remain protected.