Study guide

17.3 Manual Warewashing and Dishmachines

Certified Food Protection Manager CFPM

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 ANAB-CFP Accreditation, FDA 2-102.12, and Providers 1.3 How to Use This Guide and Study for CFPM

2 Why Food Safety Matters

2.1 Foodborne Illness, Outbreaks, and High-Risk Populations 2.2 TCS Foods and How Contamination Occurs 2.3 Person in Charge and Active Managerial Control

3 Biological Hazards

3.1 Bacteria, FAT TOM, and Sporeformers 3.2 The Big Six Pathogens 3.3 Viruses, Parasites, and Fungi 3.4 Biological Toxins

4 Chemical, Physical, and Intentional Contamination

4.1 Chemical Contaminants and Toxic Metals 4.2 Physical Contaminants 4.3 Food Defense, ALERT, and Outbreak Response

5 Major Food Allergens

5.1 The Big Nine Allergens and Symptoms 5.2 Preventing Cross-Contact 5.3 Allergen Communication, Labeling, and Service

6 The Safe Food Handler

6.1 How Food Handlers Contaminate Food 6.2 Handwashing: When and How 6.3 Gloves, Bare-Hand Contact, and the Hygiene Program

7 Employee Health

7.1 Symptoms and Reporting Responsibilities 7.2 Exclusion vs Restriction 7.3 Return-to-Work Criteria for the Big Six

8 Time and Temperature in the Flow of Food

8.1 Cross-Contamination in the Flow of Food 8.2 Temperature Danger Zone and Time Limits 8.3 Thermometers, Calibration, and Monitoring

9 Purchasing and Receiving

9.1 Approved Suppliers and Purchasing Controls 9.2 Receiving Criteria and Rejection 9.3 Receiving Specific Foods

10 Storage

10.1 FIFO, Labeling, and Date Marking 10.2 Refrigerator Storage Order and Temperatures 10.3 Dry Storage, Frozen Storage, and Chemical Separation

11 Preparation

11.1 Thawing Methods 11.2 Produce, Eggs, Ice, and Other Prep Controls 11.3 Special Processes, Variances, and ROP

12 Cooking

12.1 Minimum Internal Cooking Temperatures 12.2 Consumer Advisories and Undercooked Foods 12.3 Microwave Cooking and Non-Continuous Cooking

13 Cooling and Reheating

13.1 Two-Stage Cooling Requirements 13.2 Cooling Methods and Equipment 13.3 Reheating for Hot Holding

14 Service and Display

14.1 Hot and Cold Holding 14.2 Time as a Public Health Control 14.3 Serving, Utensils, and Self-Service 14.4 Off-Site Service, Catering, Delivery, and Vending 14.5 Refilling Returnables and Reusable Containers

15 Food Safety Management Systems

15.1 Active Managerial Control Programs 15.2 HACCP Seven Principles 15.3 Crisis Management, Recalls, and Imminent Health Hazards

16 Facilities, Equipment, Pests, and Emergencies

16.1 Facility Design, Surfaces, and Equipment 16.2 Water, Plumbing, Backflow, and Waste 16.3 Integrated Pest Management 16.4 Facility Emergencies 16.5 Plan Review, Preoperational Inspection, and the Food Safety Management System

17 Cleaning and Sanitizing

17.1 Cleaning vs Sanitizing 17.2 Chemical Sanitizers: Chlorine, Iodine, Quats 17.3 Manual Warewashing and Dishmachines 17.4 Cleaning Programs, Chemical Storage, and SDS

18 Regulatory Compliance and Staff Training

18.1 FDA Food Code, Agencies, and Inspections 18.2 Record-Keeping and Legal Duties 18.3 Staff Training and Food Safety Culture

17.3 Manual Warewashing and Dishmachines

Key Takeaways Explain This Topic AI

After scraping, the 3-compartment sink is (1) wash in detergent water at least 110°F, (2) rinse in clean water, (3) sanitize with chemical or 171°F water for 30 seconds, then air-dry.

Never towel-dry food-contact surfaces. Never wash food and utensils in the same sink without a full clean and sanitize of the sink between those jobs.

Dishmachines must follow the NSF data plate. Scrape and rack so water and sanitizer reach every surface.

Verify chemical machines with the matching test strips and heat machines with a maximum-registering thermometer or thermal labels.

If the machine cannot meet its data plate, warewash in a set-up 3-compartment sink or stop. Do not keep running dirty or unsanitized ware.

Last updated: August 2026

Warewashing is how dirty plates become food-contact surfaces again. The method is either a 3-compartment sink or a dish machine that actually meets its data plate. Both methods use the same logic: scrape, wash, rinse, sanitize, air-dry . FDA Food Code 4-501.19 sets the manual wash water at not less than 110°F (43°C) . 4-703.11 sets the sanitize methods. 4-901.11 requires air-drying . A towel that just dried a plate is a contamination tool, not a polish step.

Scrape First

Food left on a plate becomes wash-water soil. Soil uses up detergent, hides surfaces from sanitizer, and turns the first compartment into soup. Scrape, dump, or pre-rinse into a garbage bowl or disposal before the item enters the wash water. Burned-on pans soak in the wash compartment or in a designated soak sink — they do not sit in the sanitize compartment "to loosen." The third compartment is for a clean item that needs contact time, not for yesterday's lasagna.

3-Compartment Sink Order

Set the sink up before the first pan hits the water. Clean and sanitize the sink compartments themselves. Fill them for the job they will do. Then, after scraping:

Wash in detergent water at least 110°F . Detergent lifts soil. Water below 110°F is a Food Code fail even if the bubbles look busy. Change the wash water when it is greasy or cool. A thermometer in the wash compartment is not optional theater.

Rinse in clean water. Rinse removes detergent and loosened soil so the sanitizer is not neutralized. A rinse compartment full of wash-water foam is not a rinse. Change it. Do not skip rinse because the wash "looked clean."

Sanitize with a chemical solution at the labeled or Food Code concentration and contact time, or with hot water at 171°F for 30 seconds of immersion. Items must be fully submerged. A quick dip that leaves the handle dry is not contact time.

Air-dry. Rack so air reaches all surfaces. Do not towel-dry food-contact surfaces. Do not stack wet plates so the interior stays wet and the sanitizer is wiped onto the next plate's food side.

3-Comp Steps and Temperatures

Step Compartment What goes in it Temperature / concentration Fail if

0. Scrape Not a sink compartment Food waste, into garbage or disposal — Skipping scrape and loading soil into the wash water

  • 1. Wash First Detergent + water ≥ 110°F Cool, greasy, or detergent-free water
  • 2. Rinse Second Clean water Clean; replace when soiled Using leftover wash water as the "rinse"

3. Sanitize Third Chemical sanitizer or hot water Chemical at labeled ppm and contact time, or 171°F / 30 sec Weak, dirty, or cold sanitizer; a 2-second dip

4. Dry Drainboard / rack Nothing but air Air-dry Towel-drying; nesting wet ware

The drainboard after the third compartment is clean storage in progress. It is not a landing zone for dirty bus tubs.

Sinks Are Not a Combo Station

Do not wash food and utensils in the same sink unless the sink is cleaned and sanitized between those uses. A prep cook who thaws chicken in the wash compartment and then runs knives through the same basin without a sink clean-and-sanitize has contaminated the warewashing setup. Handwashing does not belong in a warewashing sink. Mop water does not belong in a warewashing sink. Each of those jobs has its own fixture. When the 3-comp is the only sink in a tiny operation, the PIC still has to clean and sanitize it between incompatible uses — and the exam still treats "we washed lettuce and then the plates in the same water" as a fail.

Dishmachines

A dish machine is a mechanical 3-comp. It is legal only when it runs the way its NSF data plate says it must run. The plate lists wash temperature, rinse or sanitizer settings, and conveyor or cycle requirements. Staff who never look at the plate cannot know whether today's cycle counted.

Scrape and rack correctly. Heavy soil still gets scraped. Overlap plates so spray arms hit food-contact surfaces, not the back of the next plate. Nested cups and bowl-in-bowl stacks create dry shadows where wash water and sanitizer never arrive. Utensils point down or follow the rack design so they do not cup dirty water. Spray arms must spin; a lime-locked arm is a mechanical fail even if the gauge reads hot.

Chemical machines inject sanitizer in the final rinse. Verify with test strips matched to that sanitizer , on a surface or in the rinse as the manufacturer directs — not by trusting the empty jug on the floor. An empty or clogged supply line produces washed, unrinsed-looking plates that are not sanitized.

High-temp machines sanitize with heat. Confirm with a maximum-registering thermometer or irreversible thermal labels on a utensil that travels the full cycle. Common teaching numbers are 180°F at the manifold and 160°F at the plate . The data plate wins if it states a different legal spec. A gauge that reads 180°F while labels on the plate stay below 160°F means the machine is not sanitizing.

Air-dry coming out of the machine the same way as the 3-comp. Do not towel-polish spots. Delime when scale appears; scale is both a heat-transfer problem and a soil harbor.

When the Machine Fails

If wash water is cold, the sanitizer strip is blank, the final rinse is below the plate, the booster is down, or the arms do not turn, stop using the machine for ware that must be sanitized. Set up the 3-compartment sink and finish legally, or stop that part of service. Do not keep sending racks through "so we stay caught up" and do not pour bleach into the wash tank as a homemade fix. A failed machine plus a chemical dump is two violations.

Saturday Night, Booster Down

The high-temp machine's booster heater dies at 7:40 p.m. Plates exit at 130°F. The PIC does not "run them twice." Twice at 130°F is still not 160°F at the plate. The 3-comp is set: 110°F wash, clean rinse, chlorine at 50–99 ppm with 7-second contact (or 171°F water if the sink can hold it), then air-dry. If the 3-comp cannot keep up, the PIC cuts the menu to what clean, sanitized ware can support. Dirty plates are not an option the certificate allows.

Exam Traps

The first trap is reversing compartments: sanitize first, or wash in sanitizer. Order is wash ≥ 110°F, rinse, sanitize, air-dry. The second is towel-drying "so they can go back on the line." 4-901.11 is air-dry. The third is treating the data-plate temperature as optional if the plates look shiny. The fourth is washing produce and pans in the same uncleaned sink. The fifth is running a dead machine because the dining room is full. The exam answer is a set-up sink or a stop, not a hope cycle.