Study guide

5.1 Medical Gas Source Equipment, Storage & Distribution Systems

AHA/ASHE Certified Health Care Constructor CHC

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Healthcare Delivery Systems & Hospital Organizational Structure

1.1 Healthcare Facility Types & Clinical Delivery Models 1.2 Hospital Governance, Clinical Leadership & Departmental Interdependencies 1.3 Healthcare Economics, Reimbursement Models & Construction Financial Impacts

2 Chapter 2: Healthcare Regulatory Framework, Accreditation & Patient Safety Culture

2.1 Healthcare Regulatory Oversight, Accreditation & Deemed Status 2.2 Patient Safety Culture, Environment of Care & Clinical Risk Management

3 Chapter 3: Healthcare Project Delivery, Contracting & Master Planning

3.1 Healthcare Project Delivery Methods & Selection Criteria 3.2 Master Facility Planning, Programming & Functional Programming 3.3 Healthcare Construction Contracts, GMP Terms & Risk Allocation

4 Chapter 4: Healthcare Codes, Standards & FGI Guidelines

4.1 Building Codes, Standards Hierarchy & AHJ Coordination 4.2 FGI Guidelines for Design and Construction of Healthcare Facilities 4.3 Core NFPA Codes in Healthcare Environments 4.4 Accessibility Guidelines, State Licensing & Pre-Occupancy Surveys

5 Chapter 5: Medical Gas & Vacuum Systems (NFPA 99)

5.1 Medical Gas Source Equipment, Storage & Distribution Systems 5.2 Medical Gas Piping Materials, Brazing Standards & Zone Valves 5.3 Medical Gas Warning Systems: Master and Area Alarms 5.4 Medical Gas Testing, Verification & Certification Procedures

6 Chapter 6: Essential Electrical Systems & Healthcare Power Infrastructure

6.1 Essential Electrical System (EES) Branches & Transfer Timelines 6.2 Emergency and Standby Power Systems, Fuel Storage & Testing 6.3 Patient Care Space Electrical Safety, Grounding & Isolated Power 6.4 Healthcare Lighting, Nurse Call Integration & Special Systems

7 Chapter 7: Healthcare HVAC, Pressurization & Infection Control Ventilation (ASHRAE 170)

7.1 ASHRAE 170 Ventilation Parameters & Thermal Comfort Limits 7.2 Airborne Infection Isolation (AII) & Protective Environment (PE) Suites 7.3 Operating Theaters, Procedure Suites & Sterile Processing Ventilation 7.4 Air Filtration Media, AHU Configuration & Ductwork Sanitation

8 Chapter 8: Plumbing, Water Management & Medical Equipment Logistics

8.1 Healthcare Plumbing Systems, Water Management & Legionella Control 8.2 Clinical Plumbing Fixtures, Medical Waste Drainage & Cross-Connection Control 8.3 Medical Equipment Coordination, Infrastructure Rough-ins & Shielding

9 Chapter 9: Healthcare Commissioning, TAB & Project Closeout

9.1 Total Building Commissioning (Cx) in Healthcare Environments 9.2 Testing, Adjusting, and Balancing (TAB) & Environmental Verification 9.3 Project Closeout Documentation, Licensing Surveys & Operational Handoff

10 Chapter 10: Pre-Construction Risk Assessment (PCRA) & Multi-Disciplinary Safety

10.1 Pre-Construction Risk Assessment (PCRA) Framework & Regulatory Mandates 10.2 Noise and Vibration Control in Occupied Clinical Facilities 10.3 Environmental Air Quality, Hazardous Materials & Worker Safety

11 Chapter 11: Infection Control Risk Assessment (ICRA 2.0) Matrix & Containment

11.1 ASHE ICRA 2.0 Matrix: Construction Types vs. Patient Risk Groups 11.2 ICRA Precaution Classes & Mandatory Engineering Controls 11.3 Dust Barriers, Air Filtration & Differential Pressure Monitoring 11.4 Personnel Entry Protocols, Tool Management & Debris Removal

12 Chapter 12: Interim Life Safety Measures (ILSM) & Construction Fire Safety

12.1 Interim Life Safety Measures (ILSM) Triggers, Policies & Assessment 12.2 The 11 Compensatory Life Safety Measures & Fire Watch Protocols 12.3 NFPA 241 Construction Safeguards & Hot Work Permitting 12.4 Fire Alarm and Automatic Sprinkler Impairment Management

13 Chapter 13: Barrier Management, Compartmentation & Utility Outage Coordination

13.1 Healthcare Compartmentation, Fire Walls & Smoke Barriers 13.2 Through-Penetration Firestopping, Fire Dampers & Above-Ceiling Permits 13.3 Defend-in-Place Principles, Evacuation & Disaster Response 13.4 Utility Shutdown Coordination & Method of Procedure (MOP)

14 Chapter 14: Healthcare Capital Budgeting, Estimating & Value Analysis

14.1 Healthcare Capital vs. Operational Budgeting & Financial Metrics 14.2 Construction Estimating in Occupied Facilities & Contingency Allocation 14.3 Clinical Value Analysis, Life-Cycle Costing (LCC) & Sustainable Design

15 Chapter 15: Healthcare Cost Control, Billing & GMP Financial Closeout

15.1 Healthcare Cost Management & Change Order Control 15.2 Healthcare Billing, GMP Reconciliation & Financial Audit

5.1 Medical Gas Source Equipment, Storage & Distribution Systems

Key Takeaways Explain This Topic AI

NFPA 99 Category 1 medical gas source systems require redundant, multi-component supplies (N+1 engineering) so that the failure of any single component cannot compromise patient life support.

Bulk cryogenic liquid oxygen systems mandate an exterior Emergency Oxygen Supply Connection (EOSC) with check valves and pressure relief to facilitate immediate hookup of a mobile cryogenic tanker during main supply failures.

Medical air compressor intakes must be located outdoors, a minimum of 25 feet from all building exhausts, fuel-fired flues, and vents, 10 feet from doors or operable windows, and at least 20 feet above ground level.

Category 1 medical air systems mandate duplex desiccant dryers producing a pressure dew point of -40°F (-40°C) or refrigerant dryers alarming at 39°F (3.9°C) at 50 psig, accompanied by continuous in-line carbon monoxide (CO) monitoring alarming at 10 ppm.

Medical-surgical vacuum pumps must discharge exhaust outdoors at least 25 feet from any outdoor air intake and 10 feet from building openings, with dedicated WAGD systems scavenging halogenated anesthetic waste.

Last updated: September 2026

5.1 Medical Gas Source Equipment, Storage & Distribution Systems

In healthcare facility construction, medical gas and vacuum systems represent true physiological extensions of life-support infrastructure. Unlike standard commercial plumbing or compressed air systems, any failure, contamination, or pressure disruption within a medical piping distribution network can result in catastrophic patient harm or instant mortality. Consequently, the National Fire Protection Association (NFPA) 99 Health Care Facilities Code establishes stringent life-safety mandates governing the design, mechanical configuration, physical isolation, and distribution architecture of these systems.

Under NFPA 99, systems are categorized based on patient risk profile:

Category 1 (Critical Care): Systems where interruption or failure of the gas or vacuum supply is likely to cause major injury or death to patients or caregivers (e.g., operating rooms, intensive care units, emergency trauma suites, post-anesthesia recovery).

Category 2 (General Care): Systems where failure is likely to cause minor injury to patients or caregivers (e.g., general medical-surgical patient rooms, outpatient procedure suites).

Category 3 & 4: Systems where failure has minimal or no clinical impact on patient safety (e.g., dental offices, localized physical therapy clinics).

For the Certified Health Care Constructor (CHC), mastering Category 1 source equipment design, physical separation requirements, and mechanical redundancies is essential to delivering compliant clinical spaces.

Bulk Cryogenic Liquid Oxygen Systems & Emergency Connections

High-volume acute care facilities consume thousands of cubic feet of medical oxygen daily to support mechanical ventilation, respiratory therapy, and surgical anesthesia. To meet this immense baseline demand economically and reliably, hospitals utilize Bulk Cryogenic Liquid Oxygen Systems , commonly referred to as Vacuum Insulated Evaporator (VIE) systems. +-------------------------------------------------------------------------+

  • | NFPA 99 BULK OXYGEN SYSTEM ARCHITECTURE |
  • | |
  • | +-------------------+ +-------------------+ |
  • | | Primary Bulk | | Secondary Bulk | |
  • | | Cryogenic Vessel | | Cryogenic Vessel | |
  • | +---------+---------+ +---------+---------+ |
  • | | | |
  • | +-------------+-------------+ |
  • | | |
  • | +----------v----------+ |
  • | | Ambient Vaporizers | |
  • | +----------+----------+ |
  • | | |
  • | +----------v----------+ |
  • | | Dual Line Regulators| |
  • | +----------+----------+ |
  • | | |
  • | Building Exterior | Building Interior |
  • | ========================|============================================ |
  • | [EOSC Station] | |
  • | (Check Valve, +---------> Main Distribution Pipeline |
  • | Relief Valve, (50 to 55 psig) |
  • | Locked Enclosure) |
  • +-------------------------------------------------------------------------+
  • Cryogenic Storage Physics & System Redundancy

Oxygen exists in a liquid state at cryogenic temperatures below -297°F (-183°C) . Storing oxygen as a cryogenic liquid achieves an expansion ratio of approximately 860 to 1 at standard atmospheric pressure and temperature, allowing enormous gas volumes to be contained within a compact physical footprint.

A Category 1 bulk oxygen installation consists of three core elements:

Primary Bulk Supply: A double-walled, vacuum-insulated cryogenic pressure vessel. The inner vessel is fabricated from high-tensile stainless steel, while the outer vessel consists of carbon steel. The annular space between vessels is filled with perlite insulation maintained under high vacuum to minimize ambient heat intrusion.

Secondary (Operating Reserve) Supply: A secondary cryogenic liquid vessel or high-pressure cylinder bank engineered to automatically supply the facility when the primary vessel is depleted, undergoes scheduled maintenance, or experiences vacuum loss.

Reserve Supply: An independent reserve supply sized to satisfy the facility's average daily consumption for a minimum of 24 hours (or longer if mandated by local emergency preparedness protocols). This reserve automatically takes over upon loss of the main and secondary supplies without dropping line pressure.

Ambient air vaporizers—finned aluminum heat exchanger columns mounted outside—utilize ambient outdoor temperature to vaporize the liquid oxygen into a gas. The gaseous oxygen then passes through a duplex pressure-reducing manifold assembly that steps system pressure down to the standard hospital pipeline distribution pressure of 50 to 55 psig .

Emergency Oxygen Supply Connection (EOSC)

Under NFPA 99, every building served by a bulk cryogenic liquid oxygen system must be equipped with an Emergency Oxygen Supply Connection (EOSC) . The EOSC provides a secure, physical hookup point on the building exterior that permits an emergency mobile liquid tanker truck to connect directly into the facility's interior oxygen distribution main during a catastrophic primary vessel failure, prolonged vendor delivery disruption, or seismic/natural disaster.

Mandatory constructor guidelines for EOSC installation include:

Location & Physical Protection: Must be mounted on the building exterior in an area directly accessible by emergency bulk delivery transport trailers under all weather conditions. The EOSC must be housed in a durable, locked, weatherproof enclosure protected against vehicular impact with heavy concrete-filled steel bollards.

Component Assembly: The EOSC assembly must include a female pipe connection fitted with an internal check valve, a manual isolation shutoff valve, a pressure relief valve set at 50% above normal distribution pressure, and a downstream line pressure gauge.

Clearance & Security: A minimum 3-foot clear working clearance must be maintained around the connection box, with keys strictly controlled by hospital facility management and emergency dispatch.

High-Pressure Compressed Gas Cylinder Manifolds

For smaller healthcare facilities, specialized clinics, and clinical gases consumed in lower volumes (such as Nitrous Oxide [N2O] , Medical Carbon Dioxide [CO2] , and High-Pressure Nitrogen [N2] for surgical power tools), high-pressure compressed gas cylinder manifolds serve as the central source.

Automatic Changeover Manifold Architecture

High-pressure manifolds operate at initial cylinder pressures between 1,800 and 2,600 psig . NFPA 99 mandates that manifolds supplying Category 1 systems be configured as dual-bank automatic changeover manifolds :

Bank A (Primary/Operating Bank): Connects to active high-pressure cylinders feeding the facility through an automated pressure-regulating assembly.

Bank B (Secondary/Reserve Bank): Houses an equal number of full standby cylinders.

When the primary bank pressure drops below a factory-set operational threshold (typically 200 to 300 psig), an internal pneumatic shuttle or electronic solenoid valve executes an automatic switchover to the reserve bank without interrupting line pressure or causing downstream pressure transients. Simultaneously, the changeover switch closes a dry contact that triggers a header changeover warning alarm at the facility's dual master alarm panels, notifying plant engineers that the primary bank is depleted and requires cylinder replacement.

Safety Relief & Manifold Room Environmental Controls

High-pressure manifolds must incorporate dual safety relief valves separated by a three-way diverter valve (transflow valve). This configuration ensures that one relief valve is always active in the flow stream while the second valve can be isolated for calibration, testing, or replacement without depressurizing the manifold.

NFPA 99 establishes strict physical architecture for cylinder storage and manifold rooms:

  • | Design Parameter | NFPA 99 Regulatory Mandate |
  • | :--- | :--- | |

| Fire-Resistance Rating | Minimum 1-hour fire-rated enclosure for cylinder volumes <3,000 cu ft; minimum 2-hour fire-rated enclosure for volumes ≥3,000 cu ft or where connected to Category 1 bulk systems. |

| Mechanical Exhaust Ventilation | Dedicated, continuous mechanical exhaust operating 24/7/365 at a rate of not less than 1.0 CFM per square foot of room area (or a minimum exhaust of 50 CFM). Natural ventilation is permitted only when the room features exterior wall openings directly to the outside. |

| Pressure Relationship | Negative pressure relative to all adjacent interior corridors and clinical spaces to prevent gas migration. |

| Electrical Infrastructure | Standard electrical wiring and lighting fixtures are permitted for non-flammable medical gases, provided switches are located outside or sealed; fixtures must be positioned away from potential cylinder venting paths. |

| Thermal Limits | Ambient room temperature must be maintained between 20°F (-7°C) and 125°F (52°C) . Rooms must not be co-located with boiler rooms, steam lines, or direct heat sources. |

| Cylinder Restraint Systems | All cylinders—whether full, partially used, or empty—must be individually secured upright using non-combustible chains, engineered wall brackets, or compartmentalized cylinder racks to prevent tip-over during seismic events or accidental impact. |

Medical Air Compressor Systems

Medical Air (USP) is classified as a manufactured pharmaceutical drug delivered directly to patients suffering from compromised pulmonary function. It must never be confused with or interconnected to commercial "shop" air, instrument air, or building control pneumatic air. Atmospheric ambient air contains high concentrations of humidity, microscopic hydrocarbons, particulate soot, carbon monoxide, and biological spores. A Category 1 Medical Air Compressor System must mechanically extract, compress, purify, and dry this air to meet United States Pharmacopeia standards. +-------------------------------------------------------------------------+

  • | CATEGORY 1 MEDICAL AIR TREATMENT TRAIN |
  • | |
  • | +-------------------+ +-------------------+ |
  • | | Compressor 1 | | Compressor 2 | (N+1 Redundancy) |
  • | | (Oil-less Scroll/ | | (Oil-less Scroll/ | |
  • | | Reciprocating) | | Reciprocating) | |
  • | +---------+---------+ +---------+---------+ |
  • | | | |
  • | +-------------+-------------+ |
  • | | |
  • | +----------v----------+ |
  • | | Aftercoolers & | |
  • | | Moisture Separators | |
  • | +----------+----------+ |
  • | | |
  • | +----------v----------+ |
  • | | ASME Air Receiver | |
  • | | (Internal Coated) | |
  • | +----------+----------+ |
  • | | |
  • | +----------v----------+ |
  • | | Duplex Desiccant | |
  • | | Dryers & Purifiers | |
  • | +----------+----------+ |
  • | | |
  • | +----------v----------+ |
  • | | Continuous Monitors | ---> Dew Point Alarm (>39°F) |
  • | | (Dew Point & CO) | ---> Carbon Monoxide Alarm (>10ppm)
  • | +----------+----------+ |
  • | | |
  • | v |
  • | To Building Distribution (50-55 psig) |
  • +-------------------------------------------------------------------------+
  • Compressor Technology & N+1 Redundancy

NFPA 99 Category 1 systems require a duplex or multiplex compressor configuration engineered with N+1 redundancy . The system capacity must be calculated such that 100% of peak hospital design demand can be fully sustained with the largest single compressor unit out of service or undergoing total mechanical teardown.

Compressor technologies must be completely oil-free or oil-less:

Oil-Less Reciprocating Compressors: Utilize sealed, permanently greased bearings isolated from the compression cylinder by an open distance piece, fitted with PTFE (Teflon) piston rings to prevent oil contamination.

Oil-Less Scroll Compressors: Feature dual intermeshing spiral scrolls that compress air without metal-to-metal contact, requiring zero internal liquid lubricants.

Water-Sealed Liquid Ring Compressors: Use recirculating water as both the sealant and cooling medium. Liquid ring units require discharge water separation and must not re-introduce water vapor into the downstream treatment stream.

Treatment Train, Filtration & Monitoring Parameters

The compressed air enters a comprehensive purification and conditioning train:

Aftercoolers: Water- or air-cooled heat exchangers equipped with automatic condensate moisture traps to lower discharge air temperature and condense liquid moisture.

Air Receiver: An ASME-coded pressure vessel treated internally with an epoxy or galvanizing anti-corrosion barrier, fitted with an automatic timed drain, manual bypass drain, safety relief valve, and pressure gauge.

Duplex Desiccant Dryers: Twin-tower regenerative desiccant dryers alternating between drying and regenerating cycles. Category 1 systems require dryers capable of producing a pressure dew point of -40°F (-40°C) . However, where refrigeration dryers are utilized under certain NFPA 99 configurations, a high dew point alarm is mandatory and must trip when the pressure dew point rises above 39°F (3.9°C) at 50 psig .

Filtration Train: Duplex pre-filters, coalescing filters to capture aerosols, 0.01-micron particulate filters, and activated carbon beds to eliminate ambient hydrocarbons and odors.

Continuous In-Line Monitoring:

Dew Point Monitor: Operates continuously; triggers an audible and visual master alarm when moisture rises above 39°F at 50 psig.

Carbon Monoxide (CO) Monitor: Continuously samples the pipeline air stream; triggers an audible and visual master alarm whenever CO concentration reaches or exceeds 10 ppm .

Medical Air Outdoor Intake Separation Rules

The physical location of the medical air compressor intake is one of the most heavily audited items on the CHC exam. The constructor must ensure that the outdoor intake is strategically sited to prevent contamination from combustion byproducts, toxic fumes, or hazardous exhausts.

Critical Exam Clearances: Medical Air Intakes (NFPA 99)

25 Feet Minimum Separation: Must be located at least 25 feet from all engine exhaust discharges (diesel emergency generators, vehicle idling zones), boiler flues, incinerators, building HVAC exhaust outlets, plumbing vent stacks, and medical vacuum or WAGD pump exhaust discharges.

20 Feet Minimum Height: Must be situated at least 20 feet above ground level to avoid automotive exhaust from driveways, emergency department ambulance bays, and loading docks.

10 Feet Minimum Separation: Must be positioned at least 10 feet away from any door, operable window, or architectural building opening.

Physical Termination: Must terminate with a downward-turned, screened hood fabricated from non-corrosive mesh (minimum 1/4" to 1/2" wire mesh) to exclude rain, birds, insects, and airborne trash.

Medical-Surgical Vacuum Systems

Medical-surgical vacuum systems provide continuous negative pressure to remove bodily fluids, arterial blood, surgical debris, and respiratory secretions during operative procedures and bedside clinical care. A standard Category 1 medical vacuum system operates at an operational line vacuum between 12 and 15 inches of mercury (in. Hg) at the terminal station inlets, with the central vacuum plant maintaining 19 to 22 in. Hg at the receiver tank.

Vacuum Pump Technologies & Configurations

Similar to medical air systems, medical-surgical vacuum packages require duplex or multiplex pumps configured with N+1 redundancy , ensuring that full clinical peak vacuum demand is met even if the single largest pump is completely non-operational. Common pump types include:

Contactless Dry Claw Pumps: Highly efficient, oil-free pumps featuring twin synchronized claw-shaped rotors that rotate in opposite directions without touching. They generate zero internal friction, require no sealing fluid, and exhibit high reliability.

Oil-Sealed Rotary Vane Pumps: Utilize recirculating oil lubricating systems. These units must be equipped with high-efficiency internal exhaust oil coalescing filters to capture 99.9% of lubricating aerosols before discharging gas.

Liquid Ring Vacuum Pumps: Utilize water as a dynamic seal, ideal for handling saturated air streams and moisture carryover without mechanical damage.

Vacuum Receiver & Outdoor Discharge Piping

Vacuum Receiver Tank: An ASME-rated steel pressure vessel designed for full vacuum service. The receiver must be fitted with an isolation valve, bottom manual drain valve (to purge accumulated biological liquid carryover), and a vacuum gauge.

Outdoor Exhaust Discharge Separation: The exhaust gas from medical-surgical vacuum pumps contains infectious bioaerosols, bloodborne pathogens, and chemical particulates. Under NFPA 99, vacuum exhaust must be piped directly to the exterior of the building:

Must terminate at least 25 feet away from any outdoor air intake (HVAC fresh air intakes or medical air compressor intakes).

Must terminate at least 10 feet away from doors, operable windows, or public walkways.

Must discharge away from normal personnel traffic areas and terminate with a downward-turned screened elbow or flapper cap at a different structural elevation than incoming air intakes.

  • Waste Anesthetic Gas Disposal (WAGD) & Instrument Air Systems
  • Waste Anesthetic Gas Disposal (WAGD)

During inhalational general anesthesia, volatile fluorinated hydrocarbon anesthetics (such as sevoflurane, desflurane, and isoflurane) and nitrous oxide are administered to patients. Only a fraction is metabolized; the remainder is exhaled into the anesthesia circuit. Waste Anesthetic Gas Disposal (WAGD) systems capture and scavenge these gases directly from the anesthesia machine's scavenging interface, preventing chronic occupational exposure and toxicity among surgical personnel.

Dedicated Vacuum Producers: While small facilities occasionally share medical-surgical vacuum pumps for WAGD service, NFPA 99 strongly encourages dedicated WAGD vacuum pumps. High concentrations of oxygen and nitrous oxide mixed with anesthetic vapors can accelerate oil breakdown in lubricated vacuum pumps and create flammability risks.

Producer Sizing: WAGD systems must be designed for continuous high-flow scavenging (typically 50 to 75 L/min per operating room). Pumps must utilize inert, non-flammable synthetic lubricants (such as fluorolube or perfluoropolyether) if exposed to high oxidizer concentrations.

Instrument Air Systems

Instrument Air is a specialized, ultra-clean, high-pressure compressed air system used specifically to power heavy pneumatic surgical tools (e.g., bone saws, orthopedic reamers, neurosurgical drills, and dermatomes) in orthopedic, trauma, and cranial surgical suites. High-pressure Nitrogen (N2) is frequently utilized as an equivalent alternative.

Operating Pressures: Distributed at 160 to 185 psig (with source pressures up to 200–250 psig), compared to the 50–55 psig distribution of standard medical air.

Purity & Dew Point: Filtered to 0.01 micron, completely hydrocarbon-free, and dried to an ultra-low pressure dew point of -40°F (-40°C) to eliminate any risk of moisture freezing or fouling high-speed precision surgical turbine handpieces.

Equipment Isolation: Instrument air compressors must never be cross-connected to medical air distribution lines due to operating pressure disparities and mechanical tool oil aerosol hazards.

Source Systems Engineering Comparison Matrix

System Standard Pipeline Pressure / Vacuum Core Source Technology Minimum Equipment Redundancy Key Environmental / Clearance Mandate

Medical Oxygen (O2) 50 – 55 psig Bulk cryogenic VIE vessel + ambient finned vaporizers Primary + Secondary + 24-hr Reserve Exterior EOSC station with crash bollards; 3 ft service clearance.

Medical Air (USP) 50 – 55 psig Oil-less reciprocating, scroll, or liquid ring compressors N+1 (100% peak demand with largest pump out) Intake ≥25 ft from exhausts, ≥20 ft above grade, ≥10 ft from doors/windows.

Medical-Surgical Vacuum 12 – 15 in. Hg (at inlets) Oil-less dry claw, rotary vane, or liquid ring pumps N+1 (100% peak demand with largest pump out) Exhaust discharge ≥25 ft from fresh air intakes, ≥10 ft from openings.

Waste Anesthetic Gas (WAGD) 12 – 15 in. Hg (or dedicated) Dedicated dry claw or inert fluid-sealed vacuum pumps N+1 recommended Exhaust direct to exterior; inert lubricants for oxidizer compatibility.

Instrument Air 160 – 185 psig Dedicated high-pressure oil-less compressors / N2 manifold N+1 redundancy Ultra-dry -40°F dew point; 0.01-micron filtration; high-pressure piping.

High-Pressure Manifolds 50 – 55 psig (N2O, CO2) Dual-bank automatic changeover manifold (A & B) Equal capacity primary and secondary banks 1-hr or 2-hr fire rating; 1.0 CFM/sq ft exhaust; cylinders chained upright.

CHC Exam Pro Tip

Pay razor-sharp attention to the Medical Air Intake clearances : 25 ft from exhaust discharges/flues, 20 ft above grade, and 10 ft from doors/windows. Also memorize the exact alarm set-points for medical air: Dew point alarms at 39°F (3.9°C) at 50 psig and Carbon Monoxide alarms at 10 ppm . If an exam question asks about cryogenic bulk oxygen backup during catastrophic tank failure, the answer is always the exterior Emergency Oxygen Supply Connection (EOSC) .