Study guide
1.1 Hazard Identification & GHS Classification
Certified Hazardous Materials Manager CHMM
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Planning and Management of Hazardous Materials
1.1 Hazard Identification & GHS Classification 1.2 Safety Data Sheets (SDS) & Chemical Compatibility 1.3 Life-Cycle Management, Source Reduction & Pollution Prevention 1.4 Chemical Inventory & Regulatory Applicability Framework 1.5 Pollution Prevention Opportunity Assessments (PPOA) & P2 Program Implementation
2 Chapter 2: Shipping and Transporting Hazardous Materials
2.1 DOT HazMat Classification & Table 172.101 2.2 Packaging Standards, Marking, Labeling & UN Specifications 2.3 Shipping Papers, Uniform Hazardous Waste Manifest & e-Manifest 2.4 Placarding Requirements, Exceptions & Modal Transport
3 Chapter 3: Storage of Hazardous Materials
3.1 RCRA Container Storage & Inspection Requirements 3.2 Aboveground (AST) & Underground Storage Tank (UST) Standards 3.3 Secondary Containment Design & Sizing Calculations 3.4 Chemical Segregation, Flammable Liquids & Compressed Gas Storage
4 Chapter 4: Facility Operations & Environmental Permitting
4.1 Process Safety Management (PSM) & Risk Management Plan (RMP) 4.2 Spill Prevention, Control, and Countermeasure (SPCC) & Facility Response Plans 4.3 Clean Air Act: Operating Permits, NESHAP & Emission Controls 4.4 Clean Water Act: NPDES, Industrial Wastewater Pretreatment & SWPPP
5 Chapter 5: Disposition of Hazardous Materials & Waste Management
5.1 RCRA Hazardous Waste Determination: Characteristic & Listed Wastes 5.2 Generator Categories (VSQG, SQG, LQG) & Accumulation Rules 5.3 Satellite Accumulation Areas (SAA) & Universal Waste Management 5.4 Used Oil Management, Land Disposal Restrictions (LDR) & TSDF Operations 5.5 Waste Profiling, Disposal Vendor Qualification & Final Disposition Documentation
6 Chapter 6: Regulatory Recordkeeping & Reporting
6.1 EPCRA Tier II (Section 312) & Toxic Release Inventory (TRI Section 313) 6.2 RCRA Biennial Reporting, Exception Reports & TSCA Reporting 6.3 Regulatory Record Retention Periods & Compliance Documentation
7 Chapter 7: Personnel Training Programs & Competency
7.1 HAZWOPER Training Standards (29 CFR 1910.120) & Emergency Roles 7.2 DOT HazMat (49 CFR 172) & RCRA Generator Training Mandates 7.3 OSHA Hazard Communication Training, Adult Learning & Competency Evaluation
8 Chapter 8: Emergency Response, Incident Command & Recovery
8.1 Emergency Response Planning & Incident Command System (ICS/NIMS) 8.2 Spill Notification: Reportable Quantities (RQ), NRC, SERC & LEPC 8.3 Spill Containment, Mitigation Techniques & Air Monitoring 8.4 Decontamination Procedures, Site Control Zones & Post-Incident Recovery
9 Chapter 9: Environmental Remediation & Site Assessment
9.1 Environmental Site Assessments: ASTM Phase I & Phase II ESA 9.2 CERCLA Superfund Process & RCRA Corrective Action 9.3 In-Situ Remediation Technologies (ISCO, SVE, Bioremediation, PRBs) 9.4 Ex-Situ Remediation Technologies, Risk-Based Corrective Action (RBCA) & CSM
10 Chapter 10: Environmental Management Systems & Compliance Auditing
10.1 ISO 14001:2015 Environmental Management Systems (EMS) & PDCA 10.2 Environmental Auditing Protocols & EPA Audit Policy (Self-Disclosure) 10.3 Root Cause Analysis, CAPA Systems & IHMM Code of Ethics 10.4 Regulatory Currency, Rulemaking Participation, Public Outreach & Environmental Cost Analysis
11 Chapter 11: Environmental Fate, Hydrogeology & Sampling
11.1 Chemical Fate and Transport Mechanisms (Partitioning, Darcy's Law, Advection) 11.2 Soil, Groundwater & Air Sampling Protocols and Chain of Custody 11.3 Data Quality Objectives (DQOs), Analytical Methods & PARCC Parameters 11.4 Human Health & Ecological Risk Assessment (HQ, Hazard Index, Cancer Risk)
12 Chapter 12: Occupational Health, Industrial Hygiene & Safety
12.1 Industrial Hygiene Principles (AREC) & Occupational Exposure Limits (PEL, TLV, REL, IDLH) 12.2 Chemical Toxicology, Routes of Entry & Dose-Response (LD50, LC50) 12.3 Hierarchy of Controls & Engineering Solutions 12.4 Personal Protective Equipment (Levels A-D) & Respiratory Protection Programs (APF, MUC) 12.5 Industrial Hygiene Monitoring Equipment (PID, FID, Multi-Gas Meters, Noise & Heat Stress) 12.6 Job Hazard Analysis (JHA), the HAZWOPER Site Safety and Health Plan (HASP) & Required Written Programs
1.1 Hazard Identification & GHS Classification
Key Takeaways Explain This Topic AI
OSHA HCS 2024 aligns primarily with GHS Revision 7 and recognizes 17 physical hazard classes, including desensitized explosives, plus 10 health hazard classes. Transition deadlines extend from May 19, 2026 for substance labels/SDSs through May 19, 2028 for employer mixture-related updates.
Under GHS, hazard severity is inversely numbered compared to NFPA 704: GHS Category 1 represents the highest/most severe hazard (Category 4 or 5 is the least severe), whereas NFPA 704 rating 4 is the most severe and 0 is minimal hazard.
GHS labels mandate six standardized elements: Product Identifier, Signal Word ('Danger' for severe hazards, 'Warning' for less severe), Hazard Statements (H-codes), Precautionary Statements (P-codes), Pictograms (8 mandatory OSHA pictograms, 1 non-mandatory environmental), and Supplier Identification.
Acute toxicity is classified across 4 categories using Acute Toxicity Estimates (ATE) based on LD50 (oral/dermal in mg/kg) and LC50 (inhalation vapors in mg/L, gases in ppmV, dusts/mists in mg/L).
HMIS (Hazardous Materials Identification System) utilizes a four-bar color-coded format (Blue-Health, Red-Flammability, Orange-Physical Hazard, White-Personal Protection) with PPE index letter codes A through K and X.
Last updated: August 2026
Hazard Identification & GHS Classification
Hazard identification is the foundational discipline of hazardous materials management. A Certified Hazardous Materials Manager (CHMM) must systematically characterize the chemical, physical, and toxicological properties of raw materials, chemical intermediates, commercial formulations, and generated waste streams. Without precise hazard classification, safe facility layout, process safety design, personal protective equipment (PPE) selection, regulatory threshold determinations, and emergency response planning are fundamentally compromised.
In the United States, chemical classification and hazard communication are governed primarily by the Occupational Safety and Health Administration (OSHA) Hazard Communication Standard (HCS) codified at 29 CFR 1910.1200 , which incorporates the United Nations' Globally Harmonized System of Classification and Labelling of Chemicals (GHS) .
1. Regulatory Foundations: OSHA HazCom & GHS
The original 1983 OSHA HazCom Standard was performance-oriented, often termed the "Right to Know" standard. Chemical manufacturers evaluated hazards using subjective criteria, resulting in conflicting Material Safety Data Sheets (MSDS) and disparate label formats across different suppliers.
OSHA's 2012 HCS aligned with GHS Revision 3. The 2024 HCS final rule , effective July 19, 2024, aligns primarily with GHS Revision 7 and adds U.S.-specific changes. OSHA extended the transition dates in January 2026: substance labels/SDSs were due May 19, 2026; employer workplace updates for substances are due November 20, 2026; mixture labels/SDSs are due November 19, 2027; and employer mixture-related updates are due May 19, 2028. During the applicable transition, regulated parties may use HCS 2012, HCS 2024, or both. The framework establishes:
Standardized Hazard Classification: Rigorous, criteria-based cutoffs for physical and health hazards.
Harmonized Label Elements: Mandatory signal words, standardized hazard statements, precautionary statements, and standardized pictograms.
16-Section Standardized Safety Data Sheets (SDS): Replacing non-standardized MSDSs.
Mandatory Employee Training: Ensuring workers comprehend pictograms, signal words, and SDS formatting. +-----------------------------------------------------------------------------------+
- | GHS CLASSIFICATION & LABELING ARCHITECTURE |
- | |
- | +--------------------------------+ +------------------------------------+ |
- | | PHYSICAL HAZARDS (17 IN HCS 2024) | | HEALTH HAZARDS (10) | |
- | | - Flammable Liquids (Cats 1-4) | | - Acute Toxicity (Cats 1-4, ATE) | |
- | | - Explosives (Div 1.1-1.6) | | - Skin Corrosion/Irritation (1A-2) | |
- | | - Oxidizers (Sol/Liq/Gas) | | - Serious Eye Damage/Irritation (1-2)| |
- | | - Organic Peroxides (Type A-G) | | - Sensitization (Resp / Skin) | |
- | | - Pyrophoric Solids/Liquids | | - Germ Cell Mutagenicity (1A/1B/2) | |
- | | - Water-Reactive Substances | | - Carcinogenicity (Cats 1A/1B/2) | |
- | | - Corrosive to Metals (Cat 1) | | - Reproductive Toxicity (1A/1B/2) | |
- | | - Gases Under Pressure | | - STOT Single (1-3) & Repeat (1-2) | |
- | | - Self-Heating / Self-Reactive | | - Aspiration Hazard (Cat 1) | |
- | +--------------------------------+ +------------------------------------+ |
- | | |
- | v |
- | +-------------------------------------------------------------------------+ |
- | | STANDARDIZED GHS LABEL ELEMENTS | |
- | | 1. Product Identifier & CAS Numbers 4. Precautionary Statements (P) | |
- | | 2. Signal Word (Danger vs Warning) 5. Pictograms (8 OSHA / 1 EPA) | |
- | | 3. Hazard Statements (H-codes) 6. Supplier Identification | |
- | +-------------------------------------------------------------------------+ |
- +-----------------------------------------------------------------------------------+
- 2. GHS Physical Hazard Classes (16 Classes)
HCS 2024 recognizes 17 physical hazard classes , including the newly added desensitized-explosives class, based on thermodynamic, kinetic, and reactive properties:
Explosives: Unstable explosives and Divisions 1.1 through 1.6 (from mass explosion hazard down to extremely insensitive articles).
Flammable Gases: Category 1A (extremely flammable gas / pyrophoric gas / chemically unstable gas), Category 1B, Category 2.
Aerosols: Categories 1, 2, and 3 based on heat of combustion and flammability test results.
Oxidizing Gases: Category 1 (gases that contribute to combustion more than air, e.g., oxygen, chlorine, fluorine).
Gases Under Pressure: Classified by physical state into Compressed gas , Liquefied gas , Refrigerated liquefied gas , and Dissolved gas (e.g., acetylene in acetone).
Flammable Liquids: Categorized strictly by closed-cup flash point ( F P FP FP ) and initial boiling point ( B P BP BP ):
GHS Category Flash Point Criteria Initial Boiling Point Criteria Examples
Category 1 F P < 23 ∘ C FP < 23^\circ\text{C} FP < 2 3 ∘ C ( 73.4 ∘ F 73.4^\circ\text{F} 73. 4 ∘ F ) B P ≤ 35 ∘ C BP \le 35^\circ\text{C} BP ≤ 3 5 ∘ C ( 95 ∘ F 95^\circ\text{F} 9 5 ∘ F ) Diethyl ether, pentane, acetaldehyde
Category 2 F P < 23 ∘ C FP < 23^\circ\text{C} FP < 2 3 ∘ C ( 73.4 ∘ F 73.4^\circ\text{F} 73. 4 ∘ F ) B P > 35 ∘ C BP > 35^\circ\text{C} BP > 3 5 ∘ C ( 95 ∘ F 95^\circ\text{F} 9 5 ∘ F ) Acetone, toluene, ethyl acetate, benzene
Category 3 23 ∘ C ≤ F P ≤ 60 ∘ C 23^\circ\text{C} \le FP \le 60^\circ\text{C} 2 3 ∘ C ≤ FP ≤ 6 0 ∘ C ( 140 ∘ F 140^\circ\text{F} 14 0 ∘ F ) Any B P BP BP Xylene, mineral spirits, cyclohexanone
Category 4 60 ∘ C < F P ≤ 93 ∘ C 60^\circ\text{C} < FP \le 93^\circ\text{C} 6 0 ∘ C < FP ≤ 9 3 ∘ C ( 199.4 ∘ F 199.4^\circ\text{F} 199. 4 ∘ F ) Any B P BP BP Diesel fuel, naphthalene, nitrobenzene
Flammable Solids: Categories 1 and 2 based on burning rate and wetted zone burn-through time.
Self-Reactive Substances and Mixtures: Types A through G (from thermally unstable explosives to non-explosive formulations).
Pyrophoric Liquids: Category 1 (liquids that ignite within 5 minutes of contact with air, e.g., triethylaluminum, butyl lithium).
Pyrophoric Solids: Category 1 (solids that ignite within 5 minutes of air contact, e.g., white phosphorus).
Self-Heating Substances: Categories 1 and 2 (materials that self-heat over long periods through air oxidation without external energy input, e.g., activated carbon, iron sponge).
Substances which in contact with water emit flammable gases: Categories 1, 2, and 3 (e.g., sodium metal, calcium carbide, potassium hydride yielding H 2 H_2 H 2 or acetylene).
Oxidizing Liquids: Categories 1, 2, and 3 based on mean burn time when mixed with cellulose (e.g., 70% perchloric acid, 50% hydrogen peroxide, nitric acid).
Oxidizing Solids: Categories 1, 2, and 3 (e.g., potassium permanganate, ammonium nitrate, sodium hypochlorite).
Organic Peroxides: Types A through G (thermally unstable substances containing bivalent − O − O − -O-O- − O − O − structure, capable of self-accelerating decomposition, detonation, or explosive burning).
Corrosive to Metals: Category 1 (corrosion rate on steel or aluminum surfaces exceeding 6.25 mm/year 6.25\text{ mm/year} 6.25 mm/year at 55 ∘ C 55^\circ\text{C} 5 5 ∘ C ).
Desensitized Explosives: Explosive chemicals wetted or otherwise phlegmatized to suppress explosive properties, classified in Categories 1–4 under HCS 2024.
3. GHS Health Hazard Classes (10 Classes)
GHS establishes 10 comprehensive health hazard classes , evaluating toxic endpoints from acute exposure through chronic, mutagenic, and developmental toxicity:
1. Acute Toxicity
Quantified via Acute Toxicity Estimates (ATE) for five exposure routes. Under OSHA HazCom, Categories 1 through 4 are adopted (Category 5 is not adopted by OSHA):
Exposure Route Category 1 (Extreme) Category 2 (High) Category 3 (Moderate) Category 4 (Low/Harmful)
Oral ( m g / k g mg/kg m g / k g body wt) ATE ≤ 5 \text{ATE} \le 5 ATE ≤ 5 5 < ATE ≤ 50 5 < \text{ATE} \le 50 5 < ATE ≤ 50 50 < ATE ≤ 300 50 < \text{ATE} \le 300 50 < ATE ≤ 300 300 < ATE ≤ 2000 300 < \text{ATE} \le 2000 300 < ATE ≤ 2000
Dermal ( m g / k g mg/kg m g / k g body wt) ATE ≤ 50 \text{ATE} \le 50 ATE ≤ 50 50 < ATE ≤ 200 50 < \text{ATE} \le 200 50 < ATE ≤ 200 200 < ATE ≤ 1000 200 < \text{ATE} \le 1000 200 < ATE ≤ 1000 1000 < ATE ≤ 2000 1000 < \text{ATE} \le 2000 1000 < ATE ≤ 2000
Inhalation: Gases ( p p m V ppmV pp mV ) ATE ≤ 100 \text{ATE} \le 100 ATE ≤ 100 100 < ATE ≤ 500 100 < \text{ATE} \le 500 100 < ATE ≤ 500 500 < ATE ≤ 2500 500 < \text{ATE} \le 2500 500 < ATE ≤ 2500 2500 < ATE ≤ 20000 2500 < \text{ATE} \le 20000 2500 < ATE ≤ 20000
Inhalation: Vapors ( m g / L mg/L m g / L ) ATE ≤ 0.5 \text{ATE} \le 0.5 ATE ≤ 0.5 0.5 < ATE ≤ 2.0 0.5 < \text{ATE} \le 2.0 0.5 < ATE ≤ 2.0 2.0 < ATE ≤ 10.0 2.0 < \text{ATE} \le 10.0 2.0 < ATE ≤ 10.0 10.0 < ATE ≤ 20.0 10.0 < \text{ATE} \le 20.0 10.0 < ATE ≤ 20.0
Inhalation: Dusts/Mists ( m g / L mg/L m g / L ) ATE ≤ 0.05 \text{ATE} \le 0.05 ATE ≤ 0.05 0.05 < ATE ≤ 0.5 0.05 < \text{ATE} \le 0.5 0.05 < ATE ≤ 0.5 0.5 < ATE ≤ 1.0 0.5 < \text{ATE} \le 1.0 0.5 < ATE ≤ 1.0 1.0 < ATE ≤ 5.0 1.0 < \text{ATE} \le 5.0 1.0 < ATE ≤ 5.0
Note
Mixture ATE Formula (Additivity Formula): When a mixture contains multiple acutely toxic ingredients with known ATEs, the overall mixture ATE is calculated using the harmonic additivity equation: 100 ATE mix = ∑ i C i ATE i \frac{100}{\text{ATE}_{\text{mix}}} = \sum_{i} \frac{C_i}{\text{ATE}_i} ATE mix 100 = ∑ i ATE i C i where C i C_i C i is the concentration percentage of ingredient i i i , and ATE i \text{ATE}_i ATE i is the individual acute toxicity estimate.
2. Skin Corrosion / Irritation
Category 1 (Corrosion): Irreversible epidermal and dermal necrosis following exposure. Subdivided into:
Category 1A: Exposure ≤ 3 min \le 3\text{ min} ≤ 3 min , observation ≤ 1 hr \le 1\text{ hr} ≤ 1 hr .
Category 1B: Exposure > 3 min > 3\text{ min} > 3 min to ≤ 1 hr \le 1\text{ hr} ≤ 1 hr , observation ≤ 14 days \le 14\text{ days} ≤ 14 days .
Category 1C: Exposure > 1 hr > 1\text{ hr} > 1 hr to ≤ 4 hours \le 4\text{ hours} ≤ 4 hours , observation ≤ 14 days \le 14\text{ days} ≤ 14 days .
Category 2 (Irritation): Reversible erythema and edema following up to 4 hours of exposure.
3. Serious Eye Damage / Eye Irritation
Category 1 (Serious Eye Damage): Irreversible tissue damage, corneal opacity, or blindness not fully reversible within 21 days.
Category 2 / 2A / 2B (Eye Irritation): Reversible ocular changes (corneal haze, iritis, conjunctival redness) clearing within 21 days (2B clearing within 7 days).
4. Respiratory or Skin Sensitization
Respiratory Sensitizer (Cat 1 / 1A / 1B): Induces hyperreactivity of airways following inhalation (e.g., isocyanates like TDI/MDI, acid anhydrides).
Skin Sensitizer (Cat 1 / 1A / 1B): Induces allergic immunological contact dermatitis (e.g., epoxy resins, nickel salts).
5. Germ Cell Mutagenicity
Category 1A: Known to induce heritable mutations in human germ cells (positive human epidemiological data).
Category 1B: Regarded as inducing heritable mutations in human germ cells (positive in vivo mammal germ cell tests).
Category 2: Causes concern for possible heritable mutations (positive in vitro/in vivo somatic tests).
6. Carcinogenicity
Category 1A: Known human carcinogen (substantial human epidemiological evidence, e.g., benzene, asbestos, hexavalent chromium).
Category 1B: Presumed human carcinogen (sufficient animal evidence or limited human evidence).
Category 2: Suspected human carcinogen (limited animal or human evidence, e.g., titanium dioxide, dichloromethane).
7. Reproductive Toxicity
Category 1A / 1B: Known or presumed human reproductive/developmental toxicant (e.g., lead, thalidomide, ethylene glycol monomethyl ether).
Category 2: Suspected reproductive toxicant.
Additional Category: Effects on or via lactation.
8. Specific Target Organ Toxicity — Single Exposure (STOT-SE)
Category 1: Significant, non-lethal toxic effects on specific target organs (e.g., liver necrosis from single massive carbon tetrachloride exposure) at low/moderate concentrations.
Category 2: Significant toxic effects at higher concentration thresholds.
Category 3: Transient target organ effects, specifically respiratory tract irritation or narcotic/central nervous system depression (drowsiness, dizziness).
9. Specific Target Organ Toxicity — Repeated Exposure (STOT-RE)
Category 1: Severe toxic damage to specific organs following prolonged/repeated exposure at low guidance values (e.g., silicosis from respirable crystalline silica, peripheral neuropathy from n-hexane).
Category 2: Significant toxic damage following repeated exposure at moderate guidance values.
10. Aspiration Hazard
Category 1: Chemical known to cause chemical pneumonitis, pulmonary edema, or death if aspirated into lungs; defined as liquid hydrocarbons with a kinematic viscosity ≤ 20.5 mm 2 / s \le 20.5\text{ mm}^2/\text{s} ≤ 20.5 mm 2 / s ( c S t cSt c St ) measured at 40 ∘ C 40^\circ\text{C} 4 0 ∘ C (e.g., gasoline, kerosene, light mineral spirits).
4. GHS Label Architecture & Standardized Elements
Under 29 CFR 1910.1200(f), shipped containers of hazardous chemicals must feature a label displaying six mandatory elements : +-----------------------------------------------------------------------------+
- | STANDARDIZED GHS CONTAINER LABEL |
- | |
- | PRODUCT IDENTIFIER: ACETONE (UN 1090) |
- | CAS NUMBER: 67-64-1 |
- | |
- | [ PICTOGRAM: Flame ] [ PICTOGRAM: Exclamation Mark ] |
- | |
- | SIGNAL WORD: DANGER |
- | |
- | HAZARD STATEMENTS: |
- | - H225: Highly flammable liquid and vapor. |
- | - H319: Causes serious eye irritation. |
- | - H336: May cause drowsiness or dizziness. |
- | |
- | PRECAUTIONARY STATEMENTS: |
- | - Prevention: P210: Keep away from heat, sparks, open flames, hot surfaces|
- | P261: Avoid breathing dust/fume/gas/mist/vapors/spray. |
- | - Response: P305+P351+P338: IF IN EYES: Rinse cautiously with water... |
- | - Storage: P403+P235: Store in a well-ventilated place. Keep cool. |
- | - Disposal: P501: Dispose of contents/container in accordance with local|
- | |
- | SUPPLIER IDENTIFICATION: ChemCorp Inc., 100 Industrial Pkwy, City, ST |
- | Emergency Phone: 1-800-555-CHEM |
- +-----------------------------------------------------------------------------+
The 6 Core Elements:
Product Identifier: Chemical name, code number, or batch matching Section 1 of the SDS.
Signal Word: Exactly one word indicating hazard severity:
DANGER: Used for more severe hazard categories.
WARNING: Used for less severe hazard categories. (Rule: If 'Danger' applies to any hazard class on the label, 'Warning' must NOT appear).
Hazard Statements (H-Codes): Standardized phrases assigned to specific hazard classes and categories describing the nature of the hazard (e.g., H200s for physical hazards, H300s for health hazards, H400s for environmental hazards).
Precautionary Statements (P-Codes): Standardized phrases describing recommended measures to minimize or prevent adverse effects, divided into five categories:
P100s: General precautions (e.g., P102: Keep out of reach of children).
P200s: Prevention measures (e.g., P280: Wear protective gloves/eye protection).
P300s: Response / First-aid actions (e.g., P301+P310: IF SWALLOWED: Immediately call poison center).
P400s: Safe Storage requirements (e.g., P403: Store in well-ventilated place).
P500s: Proper Disposal instructions (e.g., P501: Dispose of contents to hazardous waste TSDF).
Pictograms: Diamond-shaped symbols with a red border, white background, and black symbol representing specific hazard classifications.
Supplier Identification: Name, address, and emergency telephone number of the manufacturer, importer, or responsible party.
The 9 GHS Pictograms:
- Pictogram Symbol Physical Hazards Covered Health / Environmental Hazards Covered
- Flame Flammables, Pyrophorics, Self-Heating, Emits Flammable Gas, Self-Reactives, Organic Peroxides None
- Flame Over Circle Oxidizers (Gases, Liquids, Solids) None
- Exploding Bomb Explosives, Self-Reactives (Type A/B), Organic Peroxides (Type A/B) None
- Gas Cylinder Gases Under Pressure (Compressed, Liquefied, Dissolved, Cryogenic) None
- Corrosion Corrosive to Metals (Cat 1) Skin Corrosion (Cat 1A/1B/1C), Serious Eye Damage (Cat 1)
- Skull & Crossbones None Acute Toxicity — Severe / Fatal (Cats 1, 2, 3)
Health Hazard (Starburst) None Carcinogenicity, Mutagenicity, Repro Toxicity, Resp Sensitizer, STOT-SE (1,2), STOT-RE (1,2), Aspiration (1)
Exclamation Mark None Acute Toxicity — Harmful (Cat 4), Skin/Eye Irritation (Cat 2), Skin Sensitization, STOT-SE Cat 3
Environment (Dead Fish/Tree) None Acute/Chronic Aquatic Toxicity ( Non-mandatory under OSHA; enforced by EPA/DOT )
5. Critical Exam Trap: NFPA 704 vs. OSHA GHS Hazard Ranking Inversion
One of the most heavily tested concepts on the CHMM examination is the numerical hazard rating inversion between the National Fire Protection Association ( NFPA 704 ) Standard System for Emergency Response and the OSHA/GHS classification system.
Warning
THE INVERSION TRAP:
In NFPA 704 and HMIS III , 4 IS DEADLY / SEVERE , while 0 IS NO HAZARD .
In GHS / OSHA HazCom , CATEGORY 1 IS MOST SEVERE / DANGER , while CATEGORY 4 OR 5 IS LEAST SEVERE / MINIMAL HAZARD .
Confusing these two numbering systems in a facility or on the exam can lead to catastrophic misjudgments in emergency response and PPE selection! +-----------------------------------------------------------------------------+
- | HAZARD RATING SYSTEM COMPARISON: NFPA VS GHS |
- | |
- | [NFPA 704 EMERGENCY DIAMOND] [GHS CLASSIFICATION SYSTEM] |
- | |
- | [RED: Fire] |
- | 4 |
- | [BLUE: Health] [YELLOW: Reactivity] |
- | 4 0 |
- | [WHITE: Special] |
- | W |
- | |
- | SEVERITY SCALE: SEVERITY SCALE: |
- | 4 = Severe / Extreme Hazard Category 1 = Highest / Most Severe|
- | 3 = Serious Hazard Category 2 = Serious Hazard |
- | 2 = Moderate Hazard Category 3 = Moderate Hazard |
- | 1 = Slight Hazard Category 4 = Low / Least Severe |
- | 0 = Minimal / No Hazard (Category 5 = Minimal - non-OSHA)|
- | |
- | ---> 4 is DANGEROUS in NFPA! ---> 1 is DANGEROUS in GHS! |
- +-----------------------------------------------------------------------------+
NFPA 704 Standard System Breakdown:
Designed specifically for emergency responders (firefighters) entering a facility during a structural fire or catastrophic release:
Blue (Left) — Health Hazard: 0 (Normal material) to 4 (Deadly / lethal on short exposure).
Red (Top) — Flammability:
4: Flammable gas, cryogenic liquid, or liquid with F P < 22.8 ∘ C FP < 22.8^\circ\text{C} FP < 22. 8 ∘ C ( 73 ∘ F 73^\circ\text{F} 7 3 ∘ F ) and B P < 37.8 ∘ C BP < 37.8^\circ\text{C} BP < 37. 8 ∘ C ( 100 ∘ F 100^\circ\text{F} 10 0 ∘ F ).
3: Liquids with F P < 22.8 ∘ C FP < 22.8^\circ\text{C} FP < 22. 8 ∘ C and B P ≥ 37.8 ∘ C BP \ge 37.8^\circ\text{C} BP ≥ 37. 8 ∘ C , or 22.8 ∘ C ≤ F P < 37.8 ∘ C 22.8^\circ\text{C} \le FP < 37.8^\circ\text{C} 22. 8 ∘ C ≤ FP < 37. 8 ∘ C .
2: Combustible liquids with 37.8 ∘ C ≤ F P < 93.4 ∘ C 37.8^\circ\text{C} \le FP < 93.4^\circ\text{C} 37. 8 ∘ C ≤ FP < 93. 4 ∘ C ( 200 ∘ F 200^\circ\text{F} 20 0 ∘ F ).
1: Combustible materials with F P ≥ 93.4 ∘ C FP \ge 93.4^\circ\text{C} FP ≥ 93. 4 ∘ C .
0: Will not burn under exposure to 815.5 ∘ C 815.5^\circ\text{C} 815. 5 ∘ C ( 1500 ∘ F 1500^\circ\text{F} 150 0 ∘ F ) for 5 minutes.
Yellow (Right) — Instability / Reactivity: 0 (Stable) to 4 (Readily capable of detonation or explosive decomposition at normal temperatures/pressures).
White (Bottom) — Special Hazards: Only three standard symbols authorized by NFPA:
W \mathbf{W} W with slash ( W \mathcal{W} W ): Reacts violently or explosively with water.
OX: Strong oxidizer (e.g., liquid oxygen, ammonium perchlorate).
SA: Simple asphyxiant gas (authorized for nitrogen, helium, neon, argon, krypton, xenon).
Hazardous Materials Identification System (HMIS):
Developed by the American Coatings Association (ACA) for workplace chemical communication. Uses a rectangular color-bar format (Blue-Health, Red-Flammability, Orange-Physical Hazard, White-Personal Protection). The white bar uses letter codes (A through K, and X) representing specific PPE combinations:
A: Safety glasses.
B: Safety glasses + gloves.
C: Safety glasses + gloves + synthetic apron.
D: Face shield + gloves + synthetic apron.
E: Safety glasses + gloves + dust respirator.
F: Safety glasses + gloves + synthetic apron + dust respirator.
G: Safety glasses + gloves + vapor respirator.
H: Splash goggles + gloves + synthetic apron + vapor respirator.
I: Safety glasses + gloves + dust & vapor respirator.
J: Splash goggles + gloves + synthetic apron + dust & vapor respirator.
K: Airline hood or SCBA + gloves + full protective suit + boots.
X: Custom / ask supervisor for specialized handling protocols.