Study guide

1.2 Safety Data Sheets (SDS) & Chemical Compatibility

Certified Hazardous Materials Manager CHMM

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Planning and Management of Hazardous Materials

1.1 Hazard Identification & GHS Classification 1.2 Safety Data Sheets (SDS) & Chemical Compatibility 1.3 Life-Cycle Management, Source Reduction & Pollution Prevention 1.4 Chemical Inventory & Regulatory Applicability Framework 1.5 Pollution Prevention Opportunity Assessments (PPOA) & P2 Program Implementation

2 Chapter 2: Shipping and Transporting Hazardous Materials

2.1 DOT HazMat Classification & Table 172.101 2.2 Packaging Standards, Marking, Labeling & UN Specifications 2.3 Shipping Papers, Uniform Hazardous Waste Manifest & e-Manifest 2.4 Placarding Requirements, Exceptions & Modal Transport

3 Chapter 3: Storage of Hazardous Materials

3.1 RCRA Container Storage & Inspection Requirements 3.2 Aboveground (AST) & Underground Storage Tank (UST) Standards 3.3 Secondary Containment Design & Sizing Calculations 3.4 Chemical Segregation, Flammable Liquids & Compressed Gas Storage

4 Chapter 4: Facility Operations & Environmental Permitting

4.1 Process Safety Management (PSM) & Risk Management Plan (RMP) 4.2 Spill Prevention, Control, and Countermeasure (SPCC) & Facility Response Plans 4.3 Clean Air Act: Operating Permits, NESHAP & Emission Controls 4.4 Clean Water Act: NPDES, Industrial Wastewater Pretreatment & SWPPP

5 Chapter 5: Disposition of Hazardous Materials & Waste Management

5.1 RCRA Hazardous Waste Determination: Characteristic & Listed Wastes 5.2 Generator Categories (VSQG, SQG, LQG) & Accumulation Rules 5.3 Satellite Accumulation Areas (SAA) & Universal Waste Management 5.4 Used Oil Management, Land Disposal Restrictions (LDR) & TSDF Operations 5.5 Waste Profiling, Disposal Vendor Qualification & Final Disposition Documentation

6 Chapter 6: Regulatory Recordkeeping & Reporting

6.1 EPCRA Tier II (Section 312) & Toxic Release Inventory (TRI Section 313) 6.2 RCRA Biennial Reporting, Exception Reports & TSCA Reporting 6.3 Regulatory Record Retention Periods & Compliance Documentation

7 Chapter 7: Personnel Training Programs & Competency

7.1 HAZWOPER Training Standards (29 CFR 1910.120) & Emergency Roles 7.2 DOT HazMat (49 CFR 172) & RCRA Generator Training Mandates 7.3 OSHA Hazard Communication Training, Adult Learning & Competency Evaluation

8 Chapter 8: Emergency Response, Incident Command & Recovery

8.1 Emergency Response Planning & Incident Command System (ICS/NIMS) 8.2 Spill Notification: Reportable Quantities (RQ), NRC, SERC & LEPC 8.3 Spill Containment, Mitigation Techniques & Air Monitoring 8.4 Decontamination Procedures, Site Control Zones & Post-Incident Recovery

9 Chapter 9: Environmental Remediation & Site Assessment

9.1 Environmental Site Assessments: ASTM Phase I & Phase II ESA 9.2 CERCLA Superfund Process & RCRA Corrective Action 9.3 In-Situ Remediation Technologies (ISCO, SVE, Bioremediation, PRBs) 9.4 Ex-Situ Remediation Technologies, Risk-Based Corrective Action (RBCA) & CSM

10 Chapter 10: Environmental Management Systems & Compliance Auditing

10.1 ISO 14001:2015 Environmental Management Systems (EMS) & PDCA 10.2 Environmental Auditing Protocols & EPA Audit Policy (Self-Disclosure) 10.3 Root Cause Analysis, CAPA Systems & IHMM Code of Ethics 10.4 Regulatory Currency, Rulemaking Participation, Public Outreach & Environmental Cost Analysis

11 Chapter 11: Environmental Fate, Hydrogeology & Sampling

11.1 Chemical Fate and Transport Mechanisms (Partitioning, Darcy's Law, Advection) 11.2 Soil, Groundwater & Air Sampling Protocols and Chain of Custody 11.3 Data Quality Objectives (DQOs), Analytical Methods & PARCC Parameters 11.4 Human Health & Ecological Risk Assessment (HQ, Hazard Index, Cancer Risk)

12 Chapter 12: Occupational Health, Industrial Hygiene & Safety

12.1 Industrial Hygiene Principles (AREC) & Occupational Exposure Limits (PEL, TLV, REL, IDLH) 12.2 Chemical Toxicology, Routes of Entry & Dose-Response (LD50, LC50) 12.3 Hierarchy of Controls & Engineering Solutions 12.4 Personal Protective Equipment (Levels A-D) & Respiratory Protection Programs (APF, MUC) 12.5 Industrial Hygiene Monitoring Equipment (PID, FID, Multi-Gas Meters, Noise & Heat Stress) 12.6 Job Hazard Analysis (JHA), the HAZWOPER Site Safety and Health Plan (HASP) & Required Written Programs

1.2 Safety Data Sheets (SDS) & Chemical Compatibility

Key Takeaways Explain This Topic AI

OSHA 29 CFR 1910.1200(g) mandates a 16-section standardized SDS format; Sections 1–11 and 16 are OSHA-enforced, while Sections 12–15 (Ecological, Disposal, Transport, Regulatory) cover areas under EPA, DOT, or other jurisdictional oversight.

Section 9 (Physical & Chemical Properties) contains vital engineering parameters: flash point, autoignition temperature, LEL/UEL, vapor density (air=1), specific gravity (water=1), and octanol-water partition coefficient (log Kow).

Section 3 allows Confidential Business Information (CBI) / Trade Secret withholding of exact chemical identity or percentages, but mandates immediate full disclosure to treating healthcare professionals in medical emergencies.

Chemical incompatibility follows distinct binary hazard mechanisms under the EPA-600/2-80-076 Matrix, including acid-base neutralization (heat/spatter), oxidizer-organic mixing (fire/explosion), acid-cyanide/sulfide contact (toxic HCN/H2S gas), and water-reactive contact (flammable H2/toxic gas).

Alkali metals (Na, K, Li) or finely divided Al/Mg in contact with halogenated organics (e.g., methylene chloride, carbon tetrachloride) form shock-sensitive mixtures capable of violent detonation.

Last updated: August 2026

Safety Data Sheets (SDS) & Chemical Compatibility

The Safety Data Sheet (SDS) is the primary technical document communicating chemical hazards, physical properties, handling precautions, exposure limits, and emergency protocols. For the hazardous materials manager, proficiency in dissecting all 16 standardized sections is vital for building storage plans, authoring standard operating procedures (SOPs), conducting industrial hygiene assessments, and preventing catastrophic chemical mixing incidents.

Simultaneously, chemical compatibility management is an absolute regulatory and operational mandate across RCRA (40 CFR 264.17/264.177) , OSHA Process Safety Management (29 CFR 1910.119) , and OSHA HazCom (29 CFR 1910.1200) .

1. Standardized 16-Section SDS Architecture

Under 29 CFR 1910.1200(g) and GHS Annex 4, SDSs follow an invariant 16-section format, ensuring critical data appears in predictable locations across all chemical manufacturers. +----------------------------------------------------------------------------------+

  • | 16-SECTION SAFETY DATA SHEET (SDS) STRUCTURE |
  • | |
  • | OSHA MANDATORY SECTIONS (1-11 & 16) NON-MANDATORY UNDER OSHA (12-15) |
  • | +---------------------------------------+ +--------------------------------+ |
  • | | Sec 1: Identification | | Sec 12: Ecological Information | |
  • | | Sec 2: Hazard(s) Identification | | Sec 13: Disposal Considerations| |
  • | | Sec 3: Composition / Ingredients | | Sec 14: Transport Information | |
  • | | Sec 4: First-Aid Measures | | Sec 15: Regulatory Information | |
  • | | Sec 5: Fire-Fighting Measures | +--------------------------------+ |
  • | | Sec 6: Accidental Release Measures | (Enforced by EPA, DOT, etc.) |
  • | | Sec 7: Handling and Storage | |
  • | | Sec 8: Exposure Controls / PPE | |
  • | | Sec 9: Physical & Chemical Properties | |
  • | | Sec 10: Stability and Reactivity | |
  • | | Sec 11: Toxicological Information | |
  • | | Sec 16: Other Information | |
  • | +---------------------------------------+ |
  • +----------------------------------------------------------------------------------+

Detailed Breakdown of Critical Sections:

Section 1: Identification

Contains product identifier, manufacturer/distributor details, recommended uses, restrictions on use, and a 24-hour emergency telephone number (e.g., CHEMTREC).

Section 2: Hazard(s) Identification

Lists all GHS hazard classifications, signal words, hazard statements, pictograms, precautionary statements, and Hazards Not Otherwise Classified (HNOC) (e.g., combustible dust hazards, simple asphyxiants).

Section 3: Composition / Information on Ingredients

Identifies chemical ingredients, common names/synonyms, Chemical Abstracts Service ( CAS ) Registry Numbers, and exact weight percentages or concentration ranges.

Trade Secret / Confidential Business Information (CBI) Provisions (29 CFR 1910.1200(i)): Chemical manufacturers may withhold specific chemical identities or exact percentages if claimed as a trade secret. However:

All health and physical hazards associated with the secret ingredient must still be fully disclosed in Section 2 and throughout the SDS.

In a medical emergency , the manufacturer must immediately disclose the specific chemical identity to treating physicians or nurses without requiring a prior signed confidentiality agreement.

In non-emergency situations, health professionals (industrial hygienists, toxicologists) may obtain the identity by submitting a written request demonstrating occupational need and signing a confidentiality agreement.

Section 8: Exposure Controls / Personal Protection

Outlines regulatory and recommended Occupational Exposure Limits ( OELs ):

OSHA Permissible Exposure Limits (PELs) — 8-hour Time-Weighted Averages (TWA), Short-Term Exposure Limits (STEL), and Ceiling limits (29 CFR 1910.1000 Table Z-1/Z-2/Z-3).

ACGIH Threshold Limit Values (TLVs) and Biological Exposure Indices (BEIs).

NIOSH Recommended Exposure Limits (RELs) and Immediately Dangerous to Life or Health ( IDLH ) values.

Engineering Controls: Recommended ventilation and containment measures; the employer must determine the applicable regulatory and design requirements.

PPE Matrix: Specific barrier materials (e.g., specifying butyl rubber for ketones/esters, Viton for aromatics/chlorinated hydrocarbons; stating "rubber gloves" is legally deficient under OSHA).

Section 9: Physical and Chemical Properties

Provides quantitative parameters essential for fate-and-transport modeling, fire prevention, and ventilation design:

Parameter Technical Definition & Engineering Significance CHMM Exam Application

Flash Point ( F P FP FP ) Lowest temperature at which a liquid gives off sufficient vapor to form an ignitable mixture with air near its surface. Determines GHS category, DOT Packing Group, and NFPA storage cabinet rules.

Autoignition Temp ( A I T AIT A I T ) Lowest temperature at which a vapor-air mixture will spontaneously ignite without an external spark/flame. Critical in hot work permits and electrical equipment ratings (Class I, Div 1/2).

Flammability Limits (LEL / UEL) Lower and Upper Explosive Limits (% by volume in air). Below LEL is too lean; above UEL is too rich to burn. Combustible gas indicator (CGI) monitoring; confined space entry abort thresholds (typically >10% LEL).

Vapor Pressure ( V P VP V P ) Pressure exerted by a vapor in thermodynamic equilibrium with its liquid phase at a given temperature ( m m H g mmHg mm H g or k P a kPa k P a ). High V P VP V P ( > 10 mmHg >10\text{ mmHg} > 10 mmHg at 20 ∘ C 20^\circ\text{C} 2 0 ∘ C ) indicates rapid evaporation and elevated inhalation/fire risk.

Vapor Density ( V D VD V D ) Weight of vapor relative to dry air ( A i r = 1.0 Air = 1.0 A i r = 1.0 ). Calculated as V D = Molecular Weight / 28.96 VD = \text{Molecular Weight} / 28.96 V D = Molecular Weight /28.96 . If V D > 1.0 VD > 1.0 V D > 1.0 , vapor sinks into trenches/sumps; if V D < 1.0 VD < 1.0 V D < 1.0 (e.g., C H 4 , N H 3 CH_4, NH_3 C H 4 ​ , N H 3 ​ ), vapor rises and disperses.

Specific Gravity ( S G SG SG ) Density of liquid/solid relative to pure water at 4 ∘ C 4^\circ\text{C} 4 ∘ C ( W a t e r = 1.0 Water = 1.0 Wa t er = 1.0 ). If S G < 1.0 SG < 1.0 SG < 1.0 and insoluble, chemical floats (e.g., gasoline); if S G > 1.0 SG > 1.0 SG > 1.0 , it sinks (e.g., TCE, H 2 S O 4 H_2SO_4 H 2 ​ S O 4 ​ ).

pH Negative log of hydrogen ion concentration. p H ≤ 2.0 pH \le 2.0 p H ≤ 2.0 (strong acid) or p H ≥ 12.5 pH \ge 12.5 p H ≥ 12.5 (strong base) triggers RCRA D002 corrosivity and DOT Class 8.

Octanol-Water Partition Coefficient ( log ⁡ K o w \log K_{ow} lo g K o w ​ / log ⁡ P o w \log P_{ow} lo g P o w ​ ) Ratio of chemical concentration in n-octanol vs water at equilibrium. log ⁡ K o w > 3.0 \log K_{ow} > 3.0 lo g K o w ​ > 3.0 indicates high lipophilicity, bioaccumulation potential in aquatic organisms and human adipose tissue.

Section 10: Stability and Reactivity

Details chemical stability, conditions to avoid (heat, shock, light, static discharge), incompatible chemical classes, hazardous polymerization risks, and toxic decomposition byproducts (e.g., phosgene from chlorinated solvents, hydrogen cyanide from polyurethane pyrolysis, sulfur dioxide from thiol combustion).

Section 11: Toxicological Information

Contains acute toxicity test data (LD50 oral/dermal, LC50 inhalation), primary routes of exposure, acute and chronic health effects, target organ toxicity, and carcinogenicity listings by IARC (Groups 1, 2A, 2B, 3), NTP (Known, Reasonably Anticipated), and OSHA (regulated carcinogens under 29 CFR 1910.1001–1053).

2. Chemical Incompatibility & Binary Reactivity Principles

Chemical incompatibility occurs when mixing two or more substances produces an uncontrolled reaction resulting in:

Extreme heat generation (exothermic reaction causing boiling, spattering, or thermal runaway).

Fire or violent deflagration / explosion .

Toxic gas evolution (e.g., H C N , H 2 S , C l 2 , N O x , S O 2 , C O C l 2 HCN, H_2S, Cl_2, NO_x, SO_2, COCl_2 H CN , H 2 ​ S , C l 2 ​ , N O x ​ , S O 2 ​ , COC l 2 ​ ).

Flammable gas evolution (e.g., H 2 , C 2 H 2 , C H 4 H_2, C_2H_2, CH_4 H 2 ​ , C 2 ​ H 2 ​ , C H 4 ​ ).

Solubilization of toxic heavy metals .

Polymerization / rapid overpressurization of closed vessels.

The benchmark standard for chemical compatibility evaluation is the EPA-600/2-80-076 Compatibility Matrix ( A Method for Determining the Compatibility of Hazardous Wastes , Hatayama et al.). +-----------------------------------------------------------------------------------+

  • | EPA-600/2-80-076 COMPATIBILITY MATRIX: DANGEROUS MIXING PAIRS |
  • | |
  • | GROUP A CHEMICALS GROUP B CHEMICALS CONSEQUENCE |
  • | +-----------------------+ +-----------------------+ +-----------------+ |
  • | | Mineral Acids | +--> | Caustic Bases | = | Heat, Spatter | |
  • | | (HCl, H2SO4, HNO3) | | (NaOH, KOH, NH4OH) | | Neutralization | |
  • | +-----------------------+ +-----------------------+ +-----------------+ |
  • | | Strong Oxidizers | +--> | Organics / Solvents | = | Fire, Explosion,| |
  • | | (HNO3, H2O2, ClO4-) | | (Hydrocarbons, Alcs) | | Violent Deflag. | |
  • | +-----------------------+ +-----------------------+ +-----------------+ |
  • | | Cyanides / Sulfides | +--> | Mineral Acids | = | Lethal Toxic Gas| |
  • | | (NaCN, KCN, Na2S) | | (HCl, H2SO4, H3PO4) | | (HCN, H2S) | |
  • | +-----------------------+ +-----------------------+ +-----------------+ |
  • | | Water-Reactives | +--> | Aqueous Solutions | = | Flammable Gas H2| |
  • | | (Na, K, LiH, AlCl3) | | (Water, Waste Waters) | | Heat, Explosion | |
  • | +-----------------------+ +-----------------------+ +-----------------+ |
  • | | Alkali Metals | +--> | Halogenated Organics | = | Detonation, | |
  • | | (Na, K, finely div Al)| | (TCE, CCl4, CH2Cl2) | | Shock-Sensitive | |
  • | +-----------------------+ +-----------------------+ +-----------------+ |
  • +-----------------------------------------------------------------------------------+

Classic Binary Incompatibility Mechanisms Tested on the CHMM Exam:

1. Mineral Acids + Strong Caustic Bases

Reaction: Exothermic neutralization. HCl + NaOH ⟶ NaCl + H 2 O + Δ H ( Δ H = − 57.3 kJ/mol ) \text{HCl} + \text{NaOH} \longrightarrow \text{NaCl} + \text{H}_2\text{O} + \Delta H \quad (\Delta H = -57.3\text{ kJ/mol}) HCl + NaOH ⟶ NaCl + H 2 ​ O + Δ H ( Δ H = − 57.3 kJ/mol )

Consequences: Violent boiling, steam generation, rapid overpressurization of closed drums, aerosolization and splashing of corrosive liquids.

2. Strong Oxidizers + Organic Materials / Reducing Agents

Reaction: Rapid, spontaneous oxidation-reduction.

Examples: Concentrated Nitric Acid ( HNO 3 \text{HNO}_3 HNO 3 ​ ) + Acetone or Isopropanol; Hydrogen Peroxide ( > 30 % >30\% > 30% H 2 O 2 \text{H}_2\text{O}_2 H 2 ​ O 2 ​ ) + Acetic Acid; Potassium Permanganate ( KMnO 4 \text{KMnO}_4 KMnO 4 ​ ) + Glycerin.

Consequences: Spontaneous autoignition, violent combustion, shock-sensitive peroxidic/nitrated intermediates, flash fires, explosion.

3. Cyanides or Sulfides + Acids (Lethal Gas Evolution)

Reactions: NaCN + HCl ⟶ HCN ( g ) ↑ + NaCl (Hydrogen Cyanide Gas) \text{NaCN} + \text{HCl} \longrightarrow \text{HCN}_{(g)} \uparrow + \text{NaCl} \quad \text{(Hydrogen Cyanide Gas)} NaCN + HCl ⟶ HCN ( g ) ​ ↑ + NaCl (Hydrogen Cyanide Gas) Na 2 S + H 2 SO 4 ⟶ H 2 S ( g ) ↑ + Na 2 SO 4 (Hydrogen Sulfide Gas) \text{Na}_2\text{S} + \text{H}_2\text{SO}_4 \longrightarrow \text{H}_2\text{S}_{(g)} \uparrow + \text{Na}_2\text{SO}_4 \quad \text{(Hydrogen Sulfide Gas)} Na 2 ​ S + H 2 ​ SO 4 ​ ⟶ H 2 ​ S ( g ) ​ ↑ + Na 2 ​ SO 4 ​ (Hydrogen Sulfide Gas)

Consequences: Rapid generation of lethal toxic gas atmospheres within seconds. HCN \text{HCN} HCN inhibits cytochrome c oxidase in cellular respiration ( L C 50 ≈ 100 − 200 ppm LC_{50} \approx 100-200\text{ ppm} L C 50 ​ ≈ 100 − 200 ppm ); H 2 S \text{H}_2\text{S} H 2 ​ S paralyzes the olfactory nerve at > 100 ppm >100\text{ ppm} > 100 ppm and causes rapid respiratory paralysis / knockdown at > 500 ppm >500\text{ ppm} > 500 ppm .

4. Water-Reactive Chemicals + Aqueous Waste / Atmospheric Moisture

Reactions: Alkali metals ( Na , K , Li \text{Na}, \text{K}, \text{Li} Na , K , Li ), metal hydrides ( NaH , LiAlH 4 \text{NaH}, \text{LiAlH}_4 NaH , LiAlH 4 ​ ), organometallics (triethylaluminum, Grignard reagents), and chlorosilanes in contact with water. 2 Na + 2 H 2 O ⟶ 2 NaOH + H 2 ( g ) ↑ + Heat 2\text{Na} + 2\text{H}_2\text{O} \longrightarrow 2\text{NaOH} + \text{H}_{2(g)} \uparrow + \text{Heat} 2 Na + 2 H 2 ​ O ⟶ 2 NaOH + H 2 ( g ) ​ ↑ + Heat

Consequences: Copious evolution of flammable hydrogen gas ( H 2 H_2 H 2 ​ ) combined with extreme exothermic heat, leading to immediate autoignition of the hydrogen-air mixture ( L E L = 4.0 % LEL = 4.0\% L E L = 4.0% , U E L = 75.0 % UEL = 75.0\% U E L = 75.0% ).

5. Alkali Metals / Active Metals + Halogenated Hydrocarbons

Reactions: Sodium, potassium, lithium, or finely divided aluminum/magnesium powder in contact with carbon tetrachloride ( CCl 4 \text{CCl}_4 CCl 4 ​ ), methylene chloride ( CH 2 Cl 2 \text{CH}_2\text{Cl}_2 CH 2 ​ Cl 2 ​ ), trichloroethylene (TCE), or trichloroethane.

Consequences: Formation of extremely shock-sensitive, violently explosive metal-halide reaction centers capable of catastrophic detonation upon mechanical agitation.

6. Nitric Acid + Flammable Solvents or Cellulose (Wood / Rags)

Reactions: Concentrated nitric acid is both a strong mineral acid and a powerful oxidizing agent. When spilled on wooden sawdust, rags, cardboard pallets, or mixed with organic waste, it forms nitro-compounds and oxidizes the substrate.

Consequences: Spontaneous combustion after a latency period of several minutes to hours, accompanied by massive evolution of toxic red-brown nitrogen dioxide ( NO 2 \text{NO}_2 NO 2 ​ ) and nitric oxide ( NO \text{NO} NO ) gases.

3. Facility Segregation & Compatibility Management Systems

To ensure regulatory compliance and process safety across storage yards, laboratories, and waste accumulation areas:

Physical segregation: Use distance, separate containment, dikes, berms, walls, cabinets, or other measures adequate to prevent contact. Federal RCRA compatibility rules are performance-based; the 20-foot/5-foot-barrier rule applies specifically to stored oxygen versus fuel gas or combustibles, not every incompatible pair.

Separate secondary containment: Do not route incompatible spills to a shared sump. For a permitted TSDF container-storage area with free liquids, 40 CFR § 264.175 generally requires containment for 10% of container volume or the largest container, whichever is greater; do not apply that design formula universally outside its scope.

Cabinet and code evaluation: Use OSHA, fire-code/AHJ, SDS, and manufacturer requirements to select flammable-liquid and corrosive storage. Dedicated or separated acid/oxidizer compartments may be necessary, but no single cabinet configuration applies to every facility.

Electronic Compatibility Tools: Utilize NOAA's CAMEO Chemicals and Chemical Reactivity Worksheet (CRW) to digitally model multi-component mixture reactivity and predict gas evolution before bulking waste drums into tanker trucks.

Loading diagram... EPA Hazardous Waste Incompatibility and Binary Reaction Matrix