Study guide

12.3 Hierarchy of Controls & Engineering Solutions

Certified Hazardous Materials Manager CHMM

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Planning and Management of Hazardous Materials

1.1 Hazard Identification & GHS Classification 1.2 Safety Data Sheets (SDS) & Chemical Compatibility 1.3 Life-Cycle Management, Source Reduction & Pollution Prevention 1.4 Chemical Inventory & Regulatory Applicability Framework 1.5 Pollution Prevention Opportunity Assessments (PPOA) & P2 Program Implementation

2 Chapter 2: Shipping and Transporting Hazardous Materials

2.1 DOT HazMat Classification & Table 172.101 2.2 Packaging Standards, Marking, Labeling & UN Specifications 2.3 Shipping Papers, Uniform Hazardous Waste Manifest & e-Manifest 2.4 Placarding Requirements, Exceptions & Modal Transport

3 Chapter 3: Storage of Hazardous Materials

3.1 RCRA Container Storage & Inspection Requirements 3.2 Aboveground (AST) & Underground Storage Tank (UST) Standards 3.3 Secondary Containment Design & Sizing Calculations 3.4 Chemical Segregation, Flammable Liquids & Compressed Gas Storage

4 Chapter 4: Facility Operations & Environmental Permitting

4.1 Process Safety Management (PSM) & Risk Management Plan (RMP) 4.2 Spill Prevention, Control, and Countermeasure (SPCC) & Facility Response Plans 4.3 Clean Air Act: Operating Permits, NESHAP & Emission Controls 4.4 Clean Water Act: NPDES, Industrial Wastewater Pretreatment & SWPPP

5 Chapter 5: Disposition of Hazardous Materials & Waste Management

5.1 RCRA Hazardous Waste Determination: Characteristic & Listed Wastes 5.2 Generator Categories (VSQG, SQG, LQG) & Accumulation Rules 5.3 Satellite Accumulation Areas (SAA) & Universal Waste Management 5.4 Used Oil Management, Land Disposal Restrictions (LDR) & TSDF Operations 5.5 Waste Profiling, Disposal Vendor Qualification & Final Disposition Documentation

6 Chapter 6: Regulatory Recordkeeping & Reporting

6.1 EPCRA Tier II (Section 312) & Toxic Release Inventory (TRI Section 313) 6.2 RCRA Biennial Reporting, Exception Reports & TSCA Reporting 6.3 Regulatory Record Retention Periods & Compliance Documentation

7 Chapter 7: Personnel Training Programs & Competency

7.1 HAZWOPER Training Standards (29 CFR 1910.120) & Emergency Roles 7.2 DOT HazMat (49 CFR 172) & RCRA Generator Training Mandates 7.3 OSHA Hazard Communication Training, Adult Learning & Competency Evaluation

8 Chapter 8: Emergency Response, Incident Command & Recovery

8.1 Emergency Response Planning & Incident Command System (ICS/NIMS) 8.2 Spill Notification: Reportable Quantities (RQ), NRC, SERC & LEPC 8.3 Spill Containment, Mitigation Techniques & Air Monitoring 8.4 Decontamination Procedures, Site Control Zones & Post-Incident Recovery

9 Chapter 9: Environmental Remediation & Site Assessment

9.1 Environmental Site Assessments: ASTM Phase I & Phase II ESA 9.2 CERCLA Superfund Process & RCRA Corrective Action 9.3 In-Situ Remediation Technologies (ISCO, SVE, Bioremediation, PRBs) 9.4 Ex-Situ Remediation Technologies, Risk-Based Corrective Action (RBCA) & CSM

10 Chapter 10: Environmental Management Systems & Compliance Auditing

10.1 ISO 14001:2015 Environmental Management Systems (EMS) & PDCA 10.2 Environmental Auditing Protocols & EPA Audit Policy (Self-Disclosure) 10.3 Root Cause Analysis, CAPA Systems & IHMM Code of Ethics 10.4 Regulatory Currency, Rulemaking Participation, Public Outreach & Environmental Cost Analysis

11 Chapter 11: Environmental Fate, Hydrogeology & Sampling

11.1 Chemical Fate and Transport Mechanisms (Partitioning, Darcy's Law, Advection) 11.2 Soil, Groundwater & Air Sampling Protocols and Chain of Custody 11.3 Data Quality Objectives (DQOs), Analytical Methods & PARCC Parameters 11.4 Human Health & Ecological Risk Assessment (HQ, Hazard Index, Cancer Risk)

12 Chapter 12: Occupational Health, Industrial Hygiene & Safety

12.1 Industrial Hygiene Principles (AREC) & Occupational Exposure Limits (PEL, TLV, REL, IDLH) 12.2 Chemical Toxicology, Routes of Entry & Dose-Response (LD50, LC50) 12.3 Hierarchy of Controls & Engineering Solutions 12.4 Personal Protective Equipment (Levels A-D) & Respiratory Protection Programs (APF, MUC) 12.5 Industrial Hygiene Monitoring Equipment (PID, FID, Multi-Gas Meters, Noise & Heat Stress) 12.6 Job Hazard Analysis (JHA), the HAZWOPER Site Safety and Health Plan (HASP) & Required Written Programs

12.3 Hierarchy of Controls & Engineering Solutions

Key Takeaways Explain This Topic AI

The NIOSH/OSHA Hierarchy of Controls prioritizes exposure elimination, substitution, engineering controls, administrative controls, and PPE in descending order of protective reliability.

Dilution ventilation is a candidate for lower-hazard, diffuse, low-rate sources when adequate mixing and exposure control can be demonstrated. Toxicity, sensitization, carcinogenicity, process rate, and source location govern selection; 100 ppm is not a universal dividing line.

Required dilution ventilation airflow is calculated using Q = (G × 10^6 × K) / C, where G is vapor generation rate (cfm), K is a mixing factor (1 to 10), and C is target concentration (ppm).

Local Exhaust Ventilation (LEV) captures contaminants at the point of origin; hood capture airflow follows DallaValle equations: Q = Vc(10X² + A) for unflanged hoods and Q = 0.75 Vc(10X² + A) for flanged hoods.

Duct transport velocity must keep the actual contaminant entrained. Published ranges such as 1,000–2,000 fpm for gases/vapors and 3,500–4,500 fpm for many industrial dusts are design starting points, not universal regulatory minima.

Last updated: August 2026

Hierarchy of Controls & Engineering Solutions

The hierarchy of controls is the core risk-management framework for eliminating hazards and reducing exposure. OSHA standards often require feasible engineering and work-practice controls before respirators, but the exact legal duty comes from the applicable standard. Ventilation is one important engineering-control family; selection depends on source characteristics, toxicity, process constraints, and verified exposure performance.

1. The NIOSH / OSHA Hierarchy of Controls

The Hierarchy of Controls ranks risk mitigation strategies from the most inherently reliable and protective down to the least effective: +-----------------------------------------------------------------------------------+

  • | THE HIERARCHY OF CONTROLS |
  • | |
  • | MOST EFFECTIVE |
  • | +-------------------------------------------------------------------------+ |
  • | | 1. ELIMINATION | Physically remove the hazard from the process | |
  • | +-------------------------------------------------------------------------+ |
  • | | 2. SUBSTITUTION | Replace the hazard with a less hazardous chemical| |
  • | +-------------------------------------------------------------------------+ |
  • | | 3. ENGINEERING | Isolate people from the hazard (Ventilation/Enc.)| |
  • | +-------------------------------------------------------------------------+ |
  • | | 4. ADMINISTRATIVE | Change the way people work (Rotation, SOPs, Signs| |
  • | +-------------------------------------------------------------------------+ |
  • | | 5. PPE | Protect worker with Personal Protective Equipment| |
  • | +-------------------------------------------------------------------------+ |
  • | LEAST EFFECTIVE (Last Line of Defense) |
  • +-----------------------------------------------------------------------------------+
  • Tier 1: Elimination

Physically removing the hazard from the workplace. Examples include eliminating manual drum handling by designing gravity-fed piping networks, or eliminating solvent degreasing by switching to pre-treated mechanical fastening assemblies.

Tier 2: Substitution

Replacing a dangerous chemical, material, or process with a significantly less hazardous alternative. Examples include:

Replacing benzene ( P E L = 1 ppm PEL = 1\text{ ppm} PE L = 1 ppm , Group 1 human carcinogen) or trichloroethylene with aqueous ultrasonic cleaning solutions or citrus-based terpenes.

Replacing lead-based solders and primers with lead-free formulations.

Substituting dry sandblasting (respirable crystalline silica hazard) with wet abrasive blasting or garnet/steel shot.

Tier 3: Engineering Controls

Physical engineering solutions that isolate the hazard from the worker's breathing zone, operating independently of worker behavior. Examples include:

Enclosure / Isolation: Gloveboxes, fume hoods, sound-dampening acoustic enclosures around compressors.

Industrial Ventilation: Local exhaust ventilation (LEV) and dilution ventilation.

Automation / Interlocks: Automated chemical transfer systems with vapor recovery lines.

Tier 4: Administrative Controls

Managerial policies, standard operating procedures, and work scheduling designed to minimize exposure duration, frequency, or severity. Administrative controls do not remove the hazard . Examples include:

Rotating workers through high-noise or chemical vapor operations to ensure individual full-shift exposures remain below the 8-hr TWA PEL / Action Level.

Scheduling high-hazard maintenance or tank cleaning during off-shifts when fewest personnel are present.

Implementing preventative maintenance schedules and mandatory standard operating procedures (SOPs).

Tier 5: Personal Protective Equipment (PPE)

Equipping individual workers with physical protective gear (respirators, chemical suits, safety glasses, gloves). PPE is the least effective control tier because:

It acts as the final barrier; if PPE fails or is donned improperly, exposure is instantaneous.

It places heavy physiological and thermal stress on the worker.

It relies entirely on human compliance, proper fit-testing, maintenance, and training.

2. Industrial Ventilation Systems

Industrial ventilation represents the primary engineering control used to maintain airborne contaminant concentrations below OELs. Ventilation systems are divided into two fundamental categories: General Dilution Ventilation and Local Exhaust Ventilation (LEV) . +-----------------------------------------------------------------------------------+

  • | GENERAL DILUTION VENTILATION VS. LOCAL EXHAUST VENTILATION (LEV) |
  • | |
  • | GENERAL DILUTION VENTILATION LOCAL EXHAUST VENTILATION (LEV) |
  • | +------------------------------------+ +----------------------------------+ |
  • | | - Dilutes contaminant in room air | | - Captures contaminant at origin | |
  • | | - Large airflow rates required | | - Low airflow rate, high capture | |
  • | | - Lower-hazard, diffuse sources | | - Toxic or concentrated sources ||
  • | | - Demonstrated mixing is feasible | | - Five core components: Hood, | |
  • | | - Uniform, low release rates | | Duct, Air Cleaner, Fan, Stack | |
  • | | - Worker far from source | | - DallaValle capture equations | |
  • | +------------------------------------+ +----------------------------------+ |
  • +-----------------------------------------------------------------------------------+
  • General Dilution Ventilation

Dilution ventilation introduces clean outdoor air to mix with and dilute contaminated indoor air, exhausting the blended mixture out of the facility.

Screening Criteria for Dilution Ventilation Design:

The contaminant has sufficiently low toxicity for the proposed design concentration; there is no universal 100 ppm dividing line.

Contaminant release rates are small to moderate and generate at a constant, uniform rate .

Workers are situated at a sufficient distance from the contaminant generation point.

Toxic gases, vapors, or mists are distributed uniformly without stagnant dead zones.

Caution

Dilution ventilation is generally unsuitable as the primary control for highly toxic materials, carcinogens, sensitizers, uncontrolled point sources, or processes where mixing cannot be demonstrated. Evaluate the governing standard and validated engineering design rather than relying on a 100 ppm shortcut.

Dilution Airflow Formula: Q = G × 10 6 × K C Q = \frac{G \times 10^6 \times K}{C} Q = C G × 1 0 6 × K ​

where:

Q Q Q is the required dilution airflow rate in cubic feet per minute (cfm) .

G G G is the contaminant vapor generation rate in cubic feet per minute (cfm) .

K K K is the empirical mixing / safety factor (dimensionless, ranging from 1.0 1.0 1.0 for perfect mixing in idealized chambers up to 10.0 10.0 10.0 for poor mixing/turbulent airflow; typically K = 2 to 5 K = 2\text{ to }5 K = 2 to 5 ).

C C C is the target design concentration in parts per million (ppm) (typically the PEL or TLV).

If the liquid evaporation rate ( W W W , in lb/hr \text{lb/hr} lb/hr ) is known, the vapor generation rate G G G is calculated as: G = 387 × W MW × 60 G = \frac{387 \times W}{\text{MW} \times 60} G = MW × 60 387 × W ​

where MW \text{MW} MW is the molecular weight of the volatile chemical, and 387 ft 3 387\text{ ft}^3 387 ft 3 is the volume of ideal gas generated per pound-mole at standard temperature and pressure ( 70 ∘ F , 1 atm 70^\circ\text{F}, 1\text{ atm} 7 0 ∘ F , 1 atm ).

3. Local Exhaust Ventilation (LEV) Engineering

Local Exhaust Ventilation (LEV) captures airborne contaminants at or near their point of generation before they can escape into the general workroom environment and enter the employee breathing zone. LEV requires substantially lower total airflow volumes than dilution systems while providing superior protection. +-----------------------------------------------------------------------------------+

  • | 5 CORE COMPONENTS OF AN LEV SYSTEM |
  • | |
  • | [1. HOOD] ===> [2. DUCTWORK] ===> [3. AIR CLEANER] ===> [4. FAN] ===> [5. STACK]|
  • | Captures Transports air Removes dust/vapors Provides Vertical |
  • | contaminant at transport vel. (Baghouse, Carbon, static pres. discharge |
  • | at source (prevents settling) Wet Scrubber, ESP) (Centrifugal) >10ft roof|
  • +-----------------------------------------------------------------------------------+
  • 1. Hood Design & DallaValle Capture Velocity Equations

The hood is the point of entry into the LEV system. Capture velocity ( V c V_c V c ​ ) must overcome contaminant momentum and cross-drafts at the source. The following are common design-guide ranges; the designer must select and verify values for the actual process:

50 − 100 fpm 50 - 100\text{ fpm} 50 − 100 fpm : Evaporation from open tanks; degreasing.

100 − 200 fpm 100 - 200\text{ fpm} 100 − 200 fpm : Welding, barrel filling, non-spray painting.

200 − 500 fpm 200 - 500\text{ fpm} 200 − 500 fpm : Spray painting in booths, crushing, conveyor transfer.

500 − 2 , 000 fpm 500 - 2,000\text{ fpm} 500 − 2 , 000 fpm : High-velocity grinding, abrasive blasting.

DallaValle Capture Airflow Equations:

For an unflanged, freely suspended rectangular or round hood operating in open space: Q = V c ( 10 X 2 + A ) Q = V_c \left( 10 X^2 + A \right) Q = V c ​ ( 10 X 2 + A )

For a flanged hood (the addition of a flange suppresses airflow from behind the hood face, reducing required airflow by approximately 25 % 25\% 25% ): Q = 0.75 V c ( 10 X 2 + A ) Q = 0.75 \, V_c \left( 10 X^2 + A \right) Q = 0.75 V c ​ ( 10 X 2 + A )

where:

Q Q Q is required volumetric flow rate ( cfm \text{cfm} cfm ).

V c V_c V c ​ is capture velocity at distance X X X ( fpm \text{fpm} fpm ).

X X X is distance from the hood opening to the contaminant generation point ( ft \text{ft} ft ).

A A A is cross-sectional face area of the hood opening ( ft 2 \text{ft}^2 ft 2 ).

Note

Notice that airflow demand increases with the square of the distance ( X 2 X^2 X 2 ) . Doubling the distance from the hood face to the source quadruples the required airflow! Keeping hoods as close to the source as possible is the primary rule of LEV design.

2. Ductwork & Minimum Transport Velocities

Ductwork is sized to maintain a transport velocity that keeps the particular contaminant entrained without imposing unnecessary pressure loss. The following are common design ranges, not universal regulatory minima:

Contaminant Physical State Example Contaminants Minimum Duct Velocity

Gases, Vapors, Fumes Solvent vapors, welding fumes, sulfur dioxide 1 , 000 − 2 , 000 fpm 1,000 - 2,000\text{ fpm} 1 , 000 − 2 , 000 fpm

Light Mineral & Wood Dusts Fine sawdust, cotton lint, grain dust 2 , 000 − 3 , 000 fpm 2,000 - 3,000\text{ fpm} 2 , 000 − 3 , 000 fpm

Average Industrial Dusts Silica dust, grinding dust, clay, limestone 3 , 500 − 4 , 000 fpm 3,500 - 4,000\text{ fpm} 3 , 500 − 4 , 000 fpm

Heavy Industrial Dusts Lead dust, metal turnings, foundry sand, blast grit 4 , 000 − 4 , 500 + fpm 4,000 - 4,500+\text{ fpm} 4 , 000 − 4 , 500 + fpm

3. Air Cleaning Devices

Fabric Filters / Baghouses: High-efficiency ( > 99.9 % >99.9\% > 99.9% ) collection for dry particulates down to sub-micron diameters.

Cyclones: Centrifugal inertial separators used as pre-cleaners for coarse particulates ( > 10 μ m >10\text{ }\mu\text{m} > 10 μ m ).

Wet Scrubbers: Venturi and packed-bed scrubbers for acid gases, soluble mists, and explosive metal dusts (aluminum, titanium).

Activated Carbon Beds: Adsorption of volatile organic compounds (VOCs).

4. Exhaust Fan & System Pressures

Centrifugal Fans: (Radial, backward-inclined) used for industrial LEV to overcome high system static pressure losses.

Velocity Pressure ( V P VP V P ), Static Pressure ( S P SP SP ), and Total Pressure ( T P TP TP ): T P = S P + V P TP = SP + VP TP = SP + V P V = 4005 V P V = 4005 \sqrt{VP} V = 4005 V P ​

where V V V is air velocity in fpm \text{fpm} fpm , and V P VP V P is velocity pressure in inches of water gauge ( " wg "\text{wg} " wg ) at standard air density ( 0.075 lb/ft 3 0.075\text{ lb/ft}^3 0.075 lb/ft 3 ).

5. Discharge Stack Configuration

Exhaust discharge should be designed to prevent re-entrainment into air intakes and occupied zones. Vertical discharge, avoiding obstructive rain caps, adequate momentum, and separation above the roof are common strategies; values such as 3,000 fpm exit velocity or 10 feet above the roof are design guidance or code/project criteria, not universal federal LEV requirements.

Loading diagram... Hierarchy of Controls & Industrial Ventilation Decision Tree