Study guide

7.4 Sanitation, Potable Water, and Personal Hygiene Programs

CIH Certified Industrial Hygienist Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: The CIH Exam and How to Use This Guide

1.1 CIH Exam Format, Scoring, and Test-Day Logistics 1.2 Eligibility, Application Windows, Fees, and Certification Maintenance 1.3 The BGC Blueprint, Subject Areas, and a Calculation-First Study Plan

2 Chapter 2: Basic Science & Calculations

2.1 Gas Laws and Vapor Calculations 2.2 Unit Conversions: ppm, mg/m³, and Standard Temperature/Pressure 2.3 Fluid Mechanics and Airflow Fundamentals

3 Chapter 3: Air Sampling & Instrumentation

3.1 Active and Passive Air Sampling Strategies 3.2 Particulate and Aerosol Sampling 3.3 Direct-Reading Instruments and Calibration

4 Chapter 4: Analytical Chemistry & Lab Methods

4.1 Gas Chromatography and Mass Spectrometry 4.2 High-Performance Liquid Chromatography and Ion Chromatography 4.3 Spectroscopy and Elemental Analysis 4.4 Gravimetric, Microscopy, and Wet Chemical Methods 4.5 Laboratory Quality Assurance, Chain of Custody, and Desorption Efficiency

5 Chapter 5: Biostatistics & Epidemiology

5.1 Lognormal Distributions and Exposure Data Statistics 5.2 Upper Confidence Limits (UCL95) and Compliance Decision Rules 5.3 Epidemiological Study Designs and Measures of Association 5.4 Sampling Strategy: Sample Size, Power, and Worker Selection

6 Chapter 6: Toxicology & Biological Monitoring

6.1 Dose-Response Relationships and Points of Departure 6.2 Toxicokinetics: Absorption, Distribution, Metabolism, and Elimination 6.3 Aerosol Deposition, Clearance, and Respiratory Tract Dosimetry 6.4 Hepatic, Renal, Neurologic, and Hematologic Target Organ Toxicity 6.5 Pulmonary Toxicology, Carcinogenicity, and Reproductive Hazards 6.6 OEL Frameworks, Classifications, and Excursion Limits 6.7 Chemical Mixtures and Extended Work-Shift OEL Adjustments 6.8 Biological Exposure Indices (BEIs) and Biomonitoring

7 Chapter 7: Biohazards & Indoor Environmental Quality

7.1 Mold, Fungi, and Microbial Contaminants 7.2 Infectious Agents, Bloodborne Pathogens, and Biosafety Levels 7.3 Indoor Environmental Quality (IEQ) Investigations 7.4 Sanitation, Potable Water, and Personal Hygiene Programs

8 Chapter 8: Community Exposure & Environmental Health

8.1 Clean Air Act Framework, NAAQS, and New Source Review 8.2 Hazardous Air Pollutants, CEMS, and EPA Reference Methods 8.3 Atmospheric Stability, Lapse Rates, and Plume Morphology 8.4 Gaussian Plume Modeling, Plume Rise, and Environmental Fate 8.5 HAZWOPER Scope, Mandates, and Training Tiers 8.6 Protection Levels, Site Zoning, Incident Command, and Decontamination 8.7 Water Pollution, Hazardous Waste, and Community Right-to-Know

9 Chapter 9: Health Risk Analysis & Hazard Communication

9.1 GHS Hazard Classification: Health and Physical Hazard Criteria 9.2 GHS Labels, Safety Data Sheets, and Trade Secret Rules 9.3 The AIHA Exposure Assessment Strategy and Similar Exposure Groups 9.4 Qualitative Exposure Profiling and the AIHA Risk Matrix 9.5 Quantitative Health Risk Characterization: HQ, HI, and ELCR 9.6 NIOSH Occupational Exposure Banding 9.7 Risk Communication and Reporting to Affected Parties

10 Chapter 10: Industrial Ventilation Principles & LEV Design

10.1 Elimination, Substitution, Isolation, Containment, and Process Change 10.2 LEV Hood Taxonomy and Capture Velocity Selection 10.3 Hood Airflow Equations, Entry Losses, and Hood Static Pressure 10.4 Particulate Transport Aerodynamics and Duct Sizing 10.5 Duct Friction, Fitting Losses, and System Balancing 10.6 Fan Categories and Pressure Dynamics Across the Fan 10.7 System Curves, the Fan Laws, and Density Corrections

11 Chapter 11: General Ventilation, Air Cleaning & Diagnostics

11.1 Dilution Ventilation Principles and Steady-State Modeling 11.2 Transient Purging and Air Distribution Geometry 11.3 Particulate Air Cleaning: Cyclones, Baghouses, Scrubbers, and ESPs 11.4 Gaseous Emission Control and Air Cleaner Selection 11.5 Ventilation System Troubleshooting and Testing

12 Chapter 12: Noise Measurement & Hearing Conservation

12.1 Acoustic Physics and Decibel Mathematics 12.2 Sound Propagation, Octave Bands, and Frequency Weighting 12.3 Noise Dose Metrics and OSHA versus ACGIH Criteria 12.4 Exchange Rates, Extended Shifts, and Dosimetry Field Protocols 12.5 Engineering Noise Controls and Hearing Protector Attenuation 12.6 Hearing Conservation Programs and Standard Threshold Shifts 12.7 Hand-Arm and Whole-Body Vibration

13 Chapter 13: Thermal Stress Assessment & Control

13.1 Wet Bulb Globe Temperature (WBGT) and Heat Stress Indices 13.2 Heat-Related Disorders, Acclimatization, and Work/Rest Regimens 13.3 Cold Stress Evaluation and Wind Chill

14 Chapter 14: Ionizing Radiation Protection

14.1 Ionizing Radiation Physics and Radioactive Decay Kinetics 14.2 Radiation Units, Radiobiology, and Health Effects 14.3 ALARA, Stay-Time, and the Inverse Square Law 14.4 Shielding Physics, Material Selection, and Gamma Constants 14.5 Radiation Detection Instruments and Spectrometry 14.6 Personnel Dosimetry, Dose Limits, and Contamination Surveys

15 Chapter 15: Non-Ionizing Radiation & Laser Safety

15.1 The Non-Ionizing Spectrum and Static/ELF Field Exposures 15.2 Radiofrequency and Microwave Exposure: SAR, Standards, and Surveys 15.3 Ultraviolet, Visible, and Infrared Radiation Hazards 15.4 Laser Safety Classifications and Optical Density Calculations 15.5 Illumination, Lighting Design, and Visual Performance

16 Chapter 16: Non-Engineering Controls & Personal Protective Equipment

16.1 Respiratory Protection Programs and Assigned Protection Factors 16.2 Maximum Use Concentration, Oxygen Deficiency, and Breathing Air 16.3 Particulate Filters, Sorbent Cartridges, and Change Schedules 16.4 Respirator Fit Testing Protocols 16.5 Chemical Protective Clothing and Dermal Exposure Control

17 Chapter 17: Ergonomics & Workstation Design

17.1 Soft-Tissue Biomechanics and WMSD Pathophysiology 17.2 Ergonomic Risk Factors and Their Interaction Effects 17.3 The Revised NIOSH Lifting Equation 17.4 RULA, REBA, the Strain Index, and the ACGIH HAL TLV 17.5 Anthropometry and Workstation Geometry 17.6 VDT Workstations, Hand Tool Design, and Administrative Ergonomics

18 Chapter 18: Work Environments & Industrial Processes

18.1 Welding Fume Emissions, Metal Fume Fever, and Cr(VI)/Manganese Toxicology 18.2 Foundry Operations and Hot Work Fire Prevention 18.3 Vapor Degreasing, Pickling, Electroplating, and Cyanide Baths 18.4 Spray Coatings, Isocyanates, and Semiconductor Manufacturing 18.5 Confined Spaces and High-Hazard Industrial Operations 18.6 Asbestos, Lead, and Silica: Regulated Substance Programs 18.7 Abrasive Blasting and Surface Preparation

19 Chapter 19: IH Program Management & Professional Ethics

19.1 The BGC Code of Ethics: Canons and Enforcement 19.2 Professional Liability, Standard of Care, and Expert Testimony 19.3 Occupational Health & Safety Management Systems (ISO 45001, ANSI Z10) 19.4 Exposure Records Access and Medical Surveillance 19.5 OSHA Injury and Illness Recordkeeping and Enforcement

7.4 Sanitation, Potable Water, and Personal Hygiene Programs

Key Takeaways Explain This Topic AI

OSHA 29 CFR 1910.141 requires potable water for drinking and washing, prohibits common drinking cups, and requires outlets for non-potable water to be conspicuously marked as unfit to drink.

Toilet facilities are scaled to workforce size, beginning with one facility for 1 to 15 employees and increasing in steps to six for 111 to 150, plus one additional for each 40 workers above 150.

Employees may not consume or store food or beverages in any area exposed to a toxic material.

The lead, cadmium, and asbestos standards require change rooms with separated storage, showers where feasible, and lunchrooms supplied with filtered positive-pressure air.

Hand and face washing before eating and clothing controls are the primary defence against take-home contamination of workers’ families.

Last updated: August 2026

Sanitation, Personal Hygiene, and Take-Home Exposure

BGC's Biohazards subject area definition opens with " principles of sanitation, personal hygiene " before it reaches microorganisms at all. This is not a formality. Sanitation failures are a classic route of occupational and community disease, and take-home contamination is one of the few workplace hazards that reaches people who were never employed at the facility.

  • 1. OSHA 29 CFR 1910.141: The Baseline Sanitation Standard
  • Potable and non-potable water

Potable water must be provided in all places of employment for drinking, washing of the person, cooking, washing of foods, washing of cooking or eating utensils, and washing of food preparation premises.

Common drinking cups are prohibited. Portable drinking water dispensers must be closed, equipped with a tap, and designed so that water cannot be dipped from them.

Non-potable water outlets must be conspicuously posted as unfit for drinking, washing, or cooking. Non-potable water may be used only for purposes such as industrial cooling, fire protection, and cleaning of areas that do not contact food or persons.

Cross-connections between potable and non-potable systems are prohibited , because a back-siphonage event can contaminate the entire potable supply.

Toilet facilities

Toilet facilities are scaled to the number of employees:

  • Number of employees Minimum number of water closets
  • 1 to 15 1
  • 16 to 35 2
  • 36 to 55 3
  • 56 to 80 4
  • 81 to 110 5
  • 111 to 150 6
  • Over 150 6, plus 1 additional for each additional 40 employees

Separate facilities are required for each sex, except where a single toilet room can be locked from the inside and contains only one water closet.

Washing facilities

Washing facilities must be provided and maintained in a sanitary condition, with hot and cold or tepid running water, hand soap or similar cleansing agent, and individual hand towels, clean sections of continuous cloth toweling, or warm air blowers.

Change rooms and clothes drying

Where employees are required to wear protective clothing because of the possibility of contamination with toxic materials, change rooms with separate storage facilities for street clothes and for protective clothing are required — so that contaminated work clothing cannot contaminate the clothes worn home.

Food handling

Two provisions matter most:

No employee shall be allowed to consume food or beverages in a toilet room or in any area exposed to a toxic material.

Food service facilities must meet applicable sanitary standards, and waste food must be handled in covered, leak-proof, easily cleanable receptacles.

Vermin control

Every enclosed workplace must be constructed, equipped, and maintained to prevent the entrance or harbourage of rodents, insects, and other vermin, and a continuing extermination programme is required where they are detected. Vermin are both a direct disease vector and an indicator of a failed waste programme.

2. Enhanced Requirements Under Substance-Specific Standards

The general sanitation standard is a floor. The lead, cadmium, asbestos, chromium(VI), and several other substance-specific standards add much more, and the pattern is consistent:

Requirement Typical substance-specific provision

Change rooms Required where airborne exposure exceeds the PEL, with two separate lockers or storage facilities so street clothes never contact contaminated work clothes

Showers Required where feasible; employees must shower at the end of the work shift

Lunchrooms Must have a temperature-controlled, positive-pressure, filtered air supply and be readily accessible; entry in contaminated clothing is prohibited unless surface contamination has been removed

Handwashing Employees must wash hands and face prior to eating, drinking, smoking, or applying cosmetics

Clothing laundering Employer is responsible; contaminated clothing must not be removed from the workplace by employees, and blowing, shaking, or compressed-air cleaning is prohibited

Labelling Bags and containers of contaminated clothing sent for laundering must be labelled to warn the laundry workers

The prohibition on compressed-air cleaning of contaminated clothing deserves emphasis: it converts settled dust into a respirable aerosol and is one of the highest-exposure activities recorded in lead and silica workplaces.

3. Take-Home Exposure

Take-home (para-occupational) exposure occurs when a contaminant leaves the workplace on clothing, skin, hair, tools, or vehicles and exposes household members. The literature documents it clearly for lead, asbestos, beryllium, mercury, pesticides, and infectious agents , and the exposed household members — frequently children — have no occupational benefit and no protection. WORKPLACE HOME

  • -------- ----
  • Contaminated --> worn home --> Car seats, floors,
  • work clothing laundry, furniture
  • |
  • Skin/hair --> not washed --> v
  • Child hand-to-mouth
  • Tools/vehicle --> taken home --> exposure

Control follows the hierarchy exactly as it does inside the plant:

Eliminate/substitute the contaminant where possible.

Engineering: effective LEV and enclosure so clothing is not contaminated in the first place.

Administrative: mandatory shower-out and change-out, employer-provided and employer-laundered clothing, prohibition on removing work clothing from site, separate storage, and vacuuming rather than compressed air.

PPE , with correct doffing sequence and immediate containment of used items.

The single most cost-effective interventions are employer-provided laundering and a physically separated clean/dirty change room layout that makes it structurally impossible to walk from the dirty side to the exit without passing through the shower and clean locker area.

4. Sanitation in Field and Construction Settings

Construction and mobile crews are covered by the parallel construction sanitation provisions, and the practical problems are different:

Potable water must be supplied at the site, with single-use cups and a receptacle for used cups.

Toilets must be provided at the jobsite according to a similar scaling, and portable units require a servicing schedule.

Handwashing facilities must be adjacent to toilets and available before eating, which is frequently the failure point on remote sites and the reason field crews on lead or pesticide work ingest contaminant.